Search NASA⌕ Search

SEARCH · Search NASA

Results for “ACOUSTIC IMPEDANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Acoustic Treatment Design Scaling Methods: Overview, Results, and Recommendations - Volume 1

Scale model fan rigs that simulate new generation ultra-high-bypass engines at about 1/5-scale are achieving increased importance as development vehicles for the design of low-noise aircraft engines. Testing at small scale allows the tests to be performed in existing anechoic wind tunnels, which provides an accurate simulation of the important effects of aircraft forward motion on the noise generation. The ability to design, build, and test miniaturized acoustic treatment panels on scale model fan rigs representative of the fullscale engine provides not only a cost-savings, but an opportunity to optimize the treatment by allowing tests of different designs. The primary objective of this study was to develop methods that will allow scale model fan rigs to be successfully used as acoustic treatment design tools. The study focuses on finding methods to extend the upper limit of the frequency range of impedance prediction models and acoustic impedance measurement methods for subscale treatment liner designs, and confirm the predictions by correlation with measured data. This phase of the program had as a goal doubling the upper limit of impedance measurement from 6 kHz to 12 kHz. The program utilizes combined analytical and experimental methods to achieve the objectives.

Kraft, R. E.↗
NASA NTRS1973

Effect of shear on duct wall impedance.

The solution to the equation governing the propagation of sound in a uniform shear layer is expressed in terms of parabolic cylinder functions. This result is used to develop a closed-form solution for acoustic wall impedance which accounts for both the duct liner and the presence of a boundary layer in the duct. The effective wall impedance can then be used as the boundary condition for the much simpler problem of sound propagation in uniform flow.

Goldstein, M.↗
NASA NTRS2004

Improvements to the Two-Thickness Method for Deriving Acoustic Properties of Materials

The characteristic impedance and other derivative acoustic properties of a material can be derived from impedance tube data using the specific impedance measured from samples with two different thicknesses. In practice, samples are chosen so that their respective thicknesses differ by a factor of 2. This simplifies the solution of the equations relating the properties of the two samples so that the computation of the characteristic impedance is straightforward. This approach has at least two drawbacks. One is that it is often difficult to acquire or produce samples with precisely a factor of 2 difference in thickness. A second drawback is that the phase information contained in the imaginary part of the propagation constant must be unwrapped before subsequent computations are performed. For well-behaved samples, this is not a problem. For ill behaved samples of unknown properties, the phase unwrapping process can be tedious and difficult to automate. Two alternative approaches have been evaluated which remove the factor-of-2 sample thickness requirement and directly compute unwrapped phase angles. One uses a Newton-Raphson approach to solve for the roots of the samples' simultaneous equations. The other produces a wave number space diagram in which the roots are clearly discernable and easily extracted. Results are presented which illustrate the flexibility of analysis provided by the new approaches and how this can be used to better understand the limitations of the impedance tube data.

Palumbo, Daniel L.↗
NASA NTRS1990

NDE of thermal protection system for space shuttle solid rocket booster

Potential nondestructive test (NDE) methods were evaluated for detecting debonds and weak bonds in the thermal protection system (TPS) for the space shuttle solid rocket boosters. The primary thermal protection material is a sprayable, thick epoxy coating that is filled with lightweight and thermal insulating materials. Test panels were fabricated with a wide variety of hidden realistic defects, including contact debonds and weak bonds. Nondestructive test results were obtained. Candidate NDE methods evaluated for booster production applications include laser interferometry (e.g., electronic shearography), infrared thermography, radiography (e.g., computed tomography), acousto-ultrasonics, mechanical/acoustic impedance, ultrasonics, acoustic emission, and the tap test. Capabilities, advantages, disadvantages, and relative performances in defect detection of each test method for TPS bonding applications are reported. Electronic shearography NDE was technically the superior method for detecting debonds.

Myers, R. S.↗
NASA NTRS1996

The Prediction of Ducted Fan Engine Noise Via a Boundary Integral Equation Method

A computationally efficient Boundary Integral Equation Method (BIEM) for the prediction of ducted fan engine noise is presented. The key features of the BIEM are its versatility and the ability to compute rapidly any portion of the sound field without the need to compute the entire field. Governing equations for the BIEM are based on the assumptions that all acoustic processes are linear, generate spinning modes, and occur in a uniform flow field. An exterior boundary value problem (BVP) is defined that describes the scattering of incident sound by an engine duct with arbitrary profile. Boundary conditions on the duct walls are derived that allow for passive noise control treatment. The BVP is recast as a system of hypersingular boundary integral equations for the unknown duct surface quantities. BIEM solution methodology is demonstrated for the scattering of incident sound by a thin cylindrical duct with hard walls. Numerical studies are conducted for various engine parameters and continuous portions of the total pressure field are computed. Radiation and duct propagation results obtained are in agreement with the classical results of spinning mode theory for infinite ducts.

Boundary integral equation↗
NASA NTRS2011

On the Use of Experimental Methods to Improve Confidence in Educed Impedance

Results from impedance eduction methods developed by NASA Langley Research Center are used throughout the acoustic liner community. In spite of recent enhancements, occasional anomalies persist with these methods, generally at frequencies where the liner produces minimal attenuation. This investigation demonstrates an experimental approach to educe impedance with increased confidence over a desired frequency range, by combining results from successive tests with different cavity depths. A series of tests is conducted with three wire-mesh facesheets, for which the results should be weakly dependent on source sound pressure level and mean grazing flow speed. First, a raylometer is used to measure the DC flow resistance of each facesheet. These facesheets are then mounted onto a frame and a normal incidence tube is used to determine their respective acoustic impedance spectra. A comparison of the acoustic resistance component with the DC flow resistance for each facesheet is used to validate the measurement process. Next, each facesheet is successively mounted onto three frames with different cavity depths, and a grazing flow impedance tube is used to educe their respective acoustic impedance spectra with and without mean flow. The no-flow results are compared with those measured in the normal incidence tube to validate the impedance eduction method. Since the anti-resonance frequency varies with cavity depth, each sample provides robust results over a different frequency range. Hence, a combination of results can be used to determine the facesheet acoustic resistance. When combined with the acoustic reactance, observed to be weakly dependent on the source sound pressure level and grazing flow Mach number, the acoustic impedance can be educed with increased confidence. Representative results of these tests are discussed, and the complete database is available in electronic format upon request.

Jones, Michael G.↗
NASA NTRS2016

Effects of Liner Length and Attenuation on NASA Langley Impedance Eduction

This study explores the effects of liner length and attenuation on the CHE (convected Helmholtz equation) impedance eduction method, in which the surface impedance of an acoustic liner is inferred through an iterative process based on repeated solutions to the convected Helmholtz equation. Wire mesh-over-honeycomb and perforate-over-honeycomb acoustic liners are tested in the NASA Langley Grazing Flow Impedance Tube, and the resultant data are processed using two impedance eduction methods. The first is the CHE method, and the second is a direct method (labeled the KT method) that uses the Kumaresan and Tufts algorithm to compute the impedance directly. The CHE method has been extensively used for acoustic liner evaluation, but experiences anomalous behavior under some test conditions. It is postulated that the anomalies are related to the liner length and/or attenuation. Since the KT method only employs data measured over the length of the liner, it is expected to be unaffected by liner length. A comparison of results achieved with the two impedance eduction methods is used to explore the interactive effects of liner length and attenuation on the CHE impedance eduction method.

Jones, M. G.↗
NASA NTRS2024

Examination of Perforate Facesheet Impedance Prediction Models

This study examines several perforate facesheet impedance prediction models. Each model is validated with impedances educed from acoustic pressure measurements acquired in the NASA Langley Research Center Normal Incidence Tube (NIT) and Grazing Flow Impedance Tube (GFIT). This measurement dataset includes results for 73 NIT samples acquired at sound pressure levels of 100, 120, and 140 dB, and for 9 GFIT samples acquired at SPLs of 120 and 140 dB and at mean flow speeds of Mach 0.0, 0.3, and 0.5. Multiple metrics are evaluated based on different potential applications of the selected perforate facesheet model. An optimizer is then used to modify one of these models to more accurately match the full measurement dataset.

acoustic↗
NASA NTRS1981

Influence of exit impedance on finite difference solutions of transient acoustic mode propagation in ducts

The cutoff mode instability problem associated with a transient finite difference solution to the wave equation is explained. The steady-state impedance boundary condition is found to produce acoustic reflections during the initial transient, which cause finite instabilities in the cutoff modes. The stability problem is resolved by extending the duct length to prevent transient reflections. Numerical calculations are presented at forcing frequencies above, below, and nearly at the cutoff frequency, and exit impedance models are presented for use in the practical design of turbofan inlets.

Baumeister, K. J.↗
NASA NTRS1981

Influence of exit impedance on finite difference solutions of transient acoustic mode propagation in ducts

The time-dependent governing acoustic-difference equations and boundary conditions are developed and solved for sound propagation in an axisymmetric (cylindrical) hard-wall duct without flow and with spinning acoustic modes. The analysis begins with a harmonic sound source radiating into a quiescent duct. This explicit iteration method then calculates stepwise in real time to obtain the steady solutions of the acoustic field. The transient method did not converge to the steady-state solution for cutoff acoustic duct modes. This has implications as to its use in a variable-area duct, where modes may become cutoff in the smal-area portion of the duct. For single cutoff mode propagation the steady-state impedance boundary condition produced acoustic reflections during the initial transient that caused finite instabilities in the numerical calculations. The stability problem is resolved by reformulating the exit boundary condition. Example calculations show good agreement with exact analytical and numerical results for forcing frequencies above, below, and nearly at the cutoff frequency.

Baumeister, K. J.↗
NASA NTRS2003

On the Propagation of Plane Acoustic Waves in a Duct With Flexible and Impedance Walls

This Technical Memorandum (TM) discusses the harmonic and random plane acoustic waves propagating from inside a duct to its surroundings. Various duct surfaces are considered, such as rigid, flexible, and impedance. In addition, the effects of a mean flow are studied when the duct alone is considered. Results show a significant reduction in overall sound pressure levels downstream of the impedance wall for both mean flow and no mean flow cases and for a narrow duct. When a wider duct is used, the overall sound pressure level (OSPL) reduction downstream of the impedance wall is much smaller. In the far field, the directivity is such that the overall sound pressure level is reduced by about 5 decibels (dB) on the side of the impedance wall. When a flexible surface is used, the far field directivity becomes asymmetric with an increase in the OSPL on the side of the flexible surface of about 7 dB.

Frendi, Abdelkader↗
NASA NTRS2005

Benchmark Data for Evaluation of Aeroacoustic Propagation Codes With Grazing Flow

Increased understanding of the effects of acoustic treatment on the propagation of sound through commercial aircraft engine nacelles is a requirement for more efficient liner design. To this end, one of NASA s goals is to further the development of duct propagation and impedance reduction codes. A number of these codes have been developed over the last three decades. These codes are typically divided into two categories: (1) codes that use the measured complex acoustic pressure field to reduce the acoustic impedance of treatment that is positioned along the wall of the duct, and (2) codes that use the acoustic impedance of the treatment as input and compute the sound field throughout the duct. Clearly, the value of these codes is dependent upon the quality of the data used for their validation. Over the past two decades, data acquired in the NASA Langley Research Center Grazing Incidence Tube have been used by a number of researchers for comparison with their propagation codes. Many of these comparisons have been based upon Grazing Incidence Tube tests that were conducted to study specific liner technology components, and were incomplete for general propagation code validation. Thus, the objective of the current investigation is to provide a quality data set that can be used as a benchmark for evaluation of duct propagation and impedance reduction codes. In order to achieve this objective, two parallel efforts have been undertaken. The first of these is the development of an enhanced impedance eduction code that uses data acquired in the Grazing Incidence Tube. This enhancement is intended to place the benchmark data on as firm a foundation as possible. The second key effort is the acquisition of a comprehensive set of data selected to allow propagation code evaluations over a range of test conditions.

Jones, Michael G.↗
NASA NTRS2019

Overview of Liner Activities in Support of the International Forum for Aviation Research

This paper provides an overview of liner research being conducted by members of the International Forum for Aviation Research (IFAR). The IFAR consists of representatives from a number of national research labs and is established to enable information exchange on aviation research activities. NASA has provided three challenges that explore different aspects of acoustic liner research, and will compile the results from each of the partners into a common database when the challenges are completed. The goal of the first challenge is to compare experimental methods applied at different national labs for acoustic liner evaluation, and to compare impedance eduction methodologies for uniform liners. The second challenge is to evaluate the ability of 3D propagation codes to predict the effects of spanwise variable-impedance liners on the acoustic pressure field. The third challenge is to explore different approaches to simultaneously educe the impedances for each zone of a three-zone liner. Each challenge is intended to be conducted as a blind test. Thus, only representative results achieved by the NASA Liner Physics Team for each of the three challenges are presented herein. When the results from all participants are available, the compiled results are intended to be provided in future reports.

Jones, Michael G.↗
NASA NTRSDate not supplied

Investigating the Numerical Stability of Using an Impedance Boundary Condition to Model Broadband Noise Scattering With Acoustic Liners

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for achieving aircraft noise reduction and are characterized by a frequency-dependent impedance value. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering by geometric bodies treated with acoustic liners. A Broadband Impedance Model will be discussed in which the liner impedance is specified along a wide range of frequencies. The liner impedance boundary condition will be derived and coupled with a time-domain boundary integral equation to model acoustic scattering by a flat plate consisting of both un-lined and lined surfaces. The scattering solution will be obtained iteratively using both spatial and temporal basis functions and the stability will be demonstrated through eigenvalue analysis. Stability will be assessed for its dependence on time step, spatial discretization, as well as temporal basis function order. Both second- and third-order Lagrange temporal basis functions are considered.

acoustics↗
NASA NTRSDate not supplied

Investigating the Numerical Stability of Using an Impedance Boundary Condition to Model Broadband Noise Scattering With Acoustic Liners

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for achieving aircraft noise reduction and are characterized by a frequency-dependent impedance value. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering by geometric bodies treated with acoustic liners. A Broadband Impedance Model will be discussed in which the liner impedance is specified along a wide range of frequencies. The liner impedance boundary condition will be derived and coupled with a time-domain boundary integral equation to model acoustic scattering by a flat plate consisting of both un-lined and lined surfaces. The scattering solution will be obtained iteratively using both spatial and temporal basis functions and the stability will be demonstrated through eigenvalue analysis. Stability will be assessed for its dependence on time step, spatial discretization, as well as temporal basis function order. Both second- and third-order Lagrange temporal basis functions are considered.

acoustics↗