Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRCRAFT DETECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

An Approach to Detect and Mitigate Ice Particle Accretion in Aircraft Engine Compression Systems

The accretion of ice in the compression system of commercial gas turbine engines operating in high ice water content conditions is a safety issue being studied by the aviation sector. While most of the research focuses on the underlying physics of ice accretion and the meteorological conditions in which accretion can occur, a systems-level perspective on the topic lends itself to potential near-term operational improvements. This work focuses on developing an accurate and reliable algorithm for detecting the accretion of ice in the low pressure compressor of a generic 40,000 lbf thrust class engine. The algorithm uses only the two shaft speed sensors and works regardless of engine age, operating condition, and power level. In a 10,000-case Monte Carlo simulation, the detection approach was found to have excellent capability at determining ice accretion from sensor noise with detection occurring when ice blocks an average of 6.8% of the low pressure compressor area. Finally, an initial study highlights a potential mitigation strategy that uses the existing engine actuators to raise the temperature in the low pressure compressor in an effort to reduce the rate at which ice accretes.

May, Ryan D.↗

[Micron]ADS-B Detect and Avoid Flight Tests on Phantom 4 Unmanned Aircraft System

Researchers at the National Aeronautics and Space Administration Armstrong Flight Research Center in Edwards, California and Vigilant Aerospace Systems collaborated for the flight-test demonstration of an Automatic Dependent Surveillance-Broadcast based collision avoidance technology on a small unmanned aircraft system equipped with the uAvionix Automatic Dependent Surveillance-Broadcast transponder. The purpose of the testing was to demonstrate that National Aeronautics and Space Administration / Vigilant software and algorithms, commercialized as the FlightHorizon UAS"TM", are compatible with uAvionix hardware systems and the DJI Phantom 4 small unmanned aircraft system. The testing and demonstrations were necessary for both parties to further develop and certify the technology in three key areas: flights beyond visual line of sight, collision avoidance, and autonomous operations. The National Aeronautics and Space Administration and Vigilant Aerospace Systems have developed and successfully flight-tested an Automatic Dependent Surveillance-Broadcast Detect and Avoid system on the Phantom 4 small unmanned aircraft system. The Automatic Dependent Surveillance-Broadcast Detect and Avoid system architecture is especially suited for small unmanned aircraft systems because it integrates: 1) miniaturized Automatic Dependent Surveillance-Broadcast hardware; 2) radio data-link communications; 3) software algorithms for real-time Automatic Dependent Surveillance-Broadcast data integration, conflict detection, and alerting; and 4) a synthetic vision display using a fully-integrated National Aeronautics and Space Administration geobrowser for three dimensional graphical representations for ownship and air traffic situational awareness. The flight-test objectives were to evaluate the performance of Automatic Dependent Surveillance-Broadcast Detect and Avoid collision avoidance technology as installed on two small unmanned aircraft systems. In December 2016, four flight tests were conducted at Edwards Air Force Base. Researchers in the ground control station looking at displays were able to verify the Automatic Dependent Surveillance-Broadcast target detection and collision avoidance resolutions.

avoidance↗

Examining the Pilot and Controller Performance Data When in a Free Flight with Weather Phenomenon

The present study investigated effects of weather related factors on the performance of pilots under free flight. A weather scenario was defined by a combination of precipitation factors (light rain, moderate rain, and heavy rain or snow), visibility (1,4,8 miles), wind conditions (light, medium, or heavy), cloud ceiling (800ft. below, 1800ft above, and 4000ft horizontal). The performance of the aircraft self-separation was evaluated in terms of detection accuracy and detection times for student- and commercial (expert) pilots. Overall, the results obtained from a behavioral analysis showed that in general, the ability to recognize intruder aircraft conflict incidents, followed by the ability to acquire the spatial location of the intruder aircraft relative to ownership aircraft were judged to be the major cognitive tasks as perceived by the participants during self-separation. Further, the participants rarely used cockpit display of traffic information (CDTI) during conflict management related to aircraft separation, but used CDTI highly during decision-making tasks. In all weather scenarios, there were remarkable differences between expert and student pilots in detection times. In summary, weather scenarios were observed to affect intruder aircraft detection performance accuracies. There was interaction effects between weather Scenario-1 and Scenario-2 for climbing task data generated by both expert- and student- pilots at high traffic density. Scenario-3 weather condition provided an opportunity for poor detection accuracy as well as detection time increase. This may be attributed to low visibility. The intruder aircraft detection times were not affected by the weather conditions during climbing and descending tasks. The decision of pilots to fly into certain weather condition was dependent in part on the warning distance to the location of the weather. When pilots were warned of the weather conditions, they were more likely to fly their aircraft into it, but mostly when the warning was not close to the weather location.

Nituen, Celestine A.↗

Investigation of Advanced Radar Techniques for Atmospheric Hazard Detection with Airborne Weather Radar

In 2013 ProSensing Inc. conducted a study to investigate the hazard detection potential of aircraft weather radars with new measurement capabilities, such as multi-frequency, polarimetric and radiometric modes. Various radar designs and features were evaluated for sensitivity, measurement range and for detecting and quantifying atmospheric hazards in wide range of weather conditions. Projected size, weight, power consumption and cost of the various designs were also considered. Various cloud and precipitation conditions were modeled and used to conduct an analytic evaluation of the design options. This report provides an overview of the study and summarizes the conclusions and recommendations.

Pazmany, Andrew L.↗

Mitigating the Impact of Sensor Uncertainty on Unmanned Aircraft Operations

Without a pilot onboard an aircraft, a Detect-and-Avoid (DAA) system, in conjunction with surveillance sensors, must be used to provide the remotely-located Pilot-in-Command sufficient situational awareness in order to keep the Unmanned Aircraft (UA) safely separated from other aircraft. To facilitate safe operations of UA within the U.S.' National Airspace System, the uncertainty associated with surveillance sensors must be accounted for. An approach to mitigating the impact of sensor uncertainty on achievable separation has been developed to support technical requirements for DAA systems.

Jack, Devin P.↗

UAS Activity Profile Survey

Commercial vendors, trying to tap into the physical protection of critical infrastructure, are offering nuclear facilities the opportunity to borrow detection counter-unmanned aircraft systems (CUAS) equipment to survey the airspace over and around the facility. However, using one vendor or method of detection (e.g., radio frequency [RF], radar, acoustic, visual) will not necessarily provide a complete airspace profile since no single method can detect all UAS threats. Using several detection technologies, the unmanned aircraft systems (UAS) Team, who supports the U.S. National Nuclear Security Administration (NNSA) Office of International Nuclear Security (INS), would like to offer partners a comprehensive airspace profile of the types and frequency of UAS that fly within and around critical infrastructure. Improved UAS awareness will aid in the risk assessment process.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Coherent CO2 lidar systems for remote atmospheric measurements

Several examples of applications of coherent CO2 Doppler lidar systems are summarized to illustrate the potential of these systems. The applications discussed include the use of continuous-wave systems for detecting and tracking aircraft wake vortices, transverse velocity measurements, and measurements of mass flow rates of high stack emissions. The use of pulsed coherent lidars is illustrated by applications involving the measurement of thunderstorm gust fronts, the measurement of wind profiles, and clear air turbulence detection. Following a summary of previous efforts, some current programs are reviewed. These include investigations into two-dimensional wind field measurements, atmospheric backscatter measurements, transverse velocity measurements, and the feasibility of space operations.

Bilbro, J. W.↗

Remote detection of soil geochemical anomalies from an aircraft platform - Examples from the Virginia Piedmont

The use of remote-sensing data on forest leaf flush to identify areas with anomalously high soil heavy-metal concentrations is demonstrated using airborne Thematic Mapper Simulator (TMS) leaf-area-index data obtained over two sites in Virginia in spring 1983 and 1984. Mean-reflectance differences, especially in the 760-900-nm and 630-690-nm bands, corresponding to delayed leaf flush are found to be good indicators of higher heavy-metal concentration. Airborne and ground-based canopy-temperature measurements are also shown to be significantly higher in high-heavy-metal areas than in control areas.

Bell, R.↗

Icing: Accretion, Detection, Protection

The global aircraft industry and its regulatory agencies are currently involved in three major icing efforts: ground icing; advanced technologies for in-flight icing; and tailplane icing. These three major icing topics correspondingly support the three major segments of any aircraft flight profile: takeoff; cruise and hold; and approach and land. This lecture addressess these three topics in the same sequence as they appear in flight, starting with ground deicing, followed by advanced technologies for in-flight ice protection, and ending with tailplane icing.

Reinmann, John J.↗

Detecting the Onset of Fire in an Aircraft by Employing Correlation Spectroscopy

The cause of aircraft fire and locations of the fires are numerous. Worldwide, numerous in-flight fires have been passenger initiated, the prime location being the lavatory areas. Most in-flight fires in commercial carriers are of electrical origin and cigarettes. A cargo bay fire can be caused by a variety of reasons. The sheer number of different types of cargo makes it difficult to identify the origin, especially when the fire reaches the catastrophic level. The damage can be minimized, and fire can be suppressed effectively if a warning system for the onset of fire is available for onboard monitoring.

Goswami, Kisholoy↗

A Portable Ground-Based Atmospheric Monitoring System (PGAMS) for the Calibration and Validation of Atmospheric Correction Algorithms Applied to Aircraft and Satellite Images

Detecting changes in the Earth's environment using satellite images of ocean and land surfaces must take into account atmospheric effects. As a result, major programs are underway to develop algorithms for image retrieval of atmospheric aerosol properties and atmospheric correction. However, because of the temporal and spatial variability of atmospheric transmittance it is very difficult to model atmospheric effects and implement models in an operational mode. For this reason, simultaneous in situ ground measurements of atmospheric optical properties are vital to the development of accurate atmospheric correction techniques. Presented in this paper is a spectroradiometer system that provides an optimized set of surface measurements for the calibration and validation of atmospheric correction algorithms. The Portable Ground-based Atmospheric Monitoring System (PGAMS) obtains a comprehensive series of in situ irradiance, radiance, and reflectance measurements for the calibration of atmospheric correction algorithms applied to multispectral. and hyperspectral images. The observations include: total downwelling irradiance, diffuse sky irradiance, direct solar irradiance, path radiance in the direction of the north celestial pole, path radiance in the direction of the overflying satellite, almucantar scans of path radiance, full sky radiance maps, and surface reflectance. Each of these parameters are recorded over a wavelength range from 350 to 1050 nm in 512 channels. The system is fast, with the potential to acquire the complete set of observations in only 8 to 10 minutes depending on the selected spatial resolution of the sky path radiance measurements

Schiller, Stephen↗

Radar Reflectivity in Wingtip-Generated Wake Vortices

This report documents new predictive models of radar reflectivity, with meter-scale resolution, for aircraft wakes in clear air and fog. The models result from a radar design program to locate and quantify wake vortices from commercial aircraft in support of the NASA Aircraft Vortex Spacing System (AVOSS). The radar reflectivity model for clear air assumes: 1) turbulent eddies in the wake produce small discontinuities in radar refractive index; and 2) these turbulent eddies are in the 'inertial subrange' of turbulence. From these assumptions, the maximum radar frequency for detecting a particular aircraft wake, as well as the refractive index structure constant and radar volume reflectivity in the wake can be obtained from the NASA Terminal Area Simulation System (TASS) output. For fog conditions, an empirical relationship is used to calculate radar reflectivity factor from TASS output of bulk liquid water. Currently, two models exist: 1) Atlas-based on observations of liquid water and radar reflectivity factor in clouds; and 2) de Wolf- specifically tailored to a specific measured dataset (1992 Vandenberg Air Force Base).

Marshall, Robert E.↗

Development and testing of advanced redundancy management methods for the F-8 DFBW aircraft

A reliable aircraft sensor failure detection and identification (FDI) technique is presented. The technique exploits the kinematic and dynamic relationships that exist between variables measured by dissimilar sensors to identify failures in the sensors. The method is applied to management of dual redundant sensors on the NASA F-8 digital fly-by-wire (DFBW) research aircraft.

Deyst, J.↗

Alert Timing Assessment for Unmanned Aircraft System Terminal Area Operations

A Detect and Avoid (DAA) system is an essential enabler for integrating Unmanned Aircraft Systems (UAS) into the U.S. National Airspace System. A DAA system uses a suite of sensors, trackers and alerting and guidance algorithms to assist a remote pilot in maintaining separation from airborne traffic. The initial minimum performance standards focused on en route operations; in order to facilitate operations in and around the airport environment, this paper presents the derivation of the early alert threshold for UAS terminal operations.

Unmanned Aircraft Systems↗

Preliminary flight test investigation of an airborne wake vortex detection concept

NASA and the FAA have conducted a brief flight-test investigation to furnish preliminary data on the feasibility of transport aircraft wake-vortices' detection, with a view to improving airport capacity by reducing the longitudinal in-trail spacing between aircraft on landing runs. Attention was given to the possibility that the detection of strong vortices at a sufficiently early stage might furnish reasonable warning of impending aerodynamic effects. Preliminary results indicate that while maximum detection distances obtainable with wingtip-mounted flow-angularity vanes are slightly lower than had been predicted, improved detector algorithms may render them more sensitive.

Verstynen, Harry A.↗

Predictive Information: Status or Alert Information?

Previous research investigating the efficacy of predictive information for detecting and diagnosing aircraft system failures found that subjects like to have predictive information concerning when a parameter would reach an alert range. This research focused on where the predictive information should be located, whether the information should be more closely associated with the parameter information or with the alert information. Each subject saw 3 forms of predictive information: (1) none, (2) a predictive alert message, and (3) predictive information on the status display. Generally, subjects performed better and preferred to have predictive information available although the difference between status and alert predictive information was minimal. Overall, for detection and recalling what happened, status predictive information is best; however for diagnosis, alert predictive information holds a slight edge.

Trujillo, Anna C.↗

NASA UAS Integration into the NAS Project: Human Systems Integration

This presentation provides an overview of the work the Human Systems Integration (HSI) sub-project has done on detect and avoid (DAA) displays while working on the UAS (Unmanned Aircraft System) Integration into the NAS project. The most recent simulation on DAA interoperability with Traffic Collision Avoidance System (TCAS) is discussed in the most detail. The relationship of the work to the larger UAS community and next steps are also detailed.

unmanned aircraft systems↗

A Unified Nonlinear Adaptive Approach for Detection and Isolation of Engine Faults

A challenging problem in aircraft engine health management (EHM) system development is to detect and isolate faults in system components (i.e., compressor, turbine), actuators, and sensors. Existing nonlinear EHM methods often deal with component faults, actuator faults, and sensor faults separately, which may potentially lead to incorrect diagnostic decisions and unnecessary maintenance. Therefore, it would be ideal to address sensor faults, actuator faults, and component faults under one unified framework. This paper presents a systematic and unified nonlinear adaptive framework for detecting and isolating sensor faults, actuator faults, and component faults for aircraft engines. The fault detection and isolation (FDI) architecture consists of a parallel bank of nonlinear adaptive estimators. Adaptive thresholds are appropriately designed such that, in the presence of a particular fault, all components of the residual generated by the adaptive estimator corresponding to the actual fault type remain below their thresholds. If the faults are sufficiently different, then at least one component of the residual generated by each remaining adaptive estimator should exceed its threshold. Therefore, based on the specific response of the residuals, sensor faults, actuator faults, and component faults can be isolated. The effectiveness of the approach was evaluated using the NASA C-MAPSS turbofan engine model, and simulation results are presented.

Tang, Liang↗