Search NASA⌕ Search

SEARCH · Search NASA

Results for “ARC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Fluctuations of precipitated electron intensity in flickering auroral arcs

Electron spectra associated with two aurorae observed by ground-based television are reported. One auroral arc was observed to flicker, large variations in the precipitated electron energy occurring on a time scale of 114 ms. The major variations occur at the higher energies of the 0.5-20 keV range covered by the detectors. Changes in the particle flux occur primarily in the pitch angle range 0 to 60 deg. Analysis of the video data shows a larger variation in intensity along the lower border of the arc in keeping with the results of the electron spectra. The second arc was not observed to flicker, and the associated electron spectra and video data show no large variations in precipitated electron energy or video intensity modulation. While pitch-angle distributions tend to be field-aligned in the first arc, the distributions in the second arc are nearly isotropic or peaked from 60 to 90 deg in the downward hemisphere.

Spiger, R. J.↗

A sun-aligned arc observed by DMSP and AE-C

On May 12, 1977, 8 minutes after a DMSP satellite photographed a sun-aligned auroral arc in the southern polar cap, AE-C crossed over the same arc. Precipitating electrons were observed with a peak energy flux of 0.94 erg per sq cm s but with no clear monoenergetic beam, and coincident ion precipitation was measured at energies of a few keV. A very sharp ion convection reversal was found coincident with the particle precipitation and embedded in a region of constant antisunward flow. Magnetic field data indicate that the arc occurred during the recovery phase of a weak magnetic storm, with the IMF in a toward sector and the Z component nearly zero. The data are consistent with a source of particles at altitudes of the order of 5-8 R(E) on field lines containing the plasma sheet boundary layer. The electron spectra do not indicate the existence of an electrostatic potential along the magnetic field lines projecting from the arc. The electrodynamic properties associated with the arc appear to be consistent with a simple model in which field-aligned currents are required along any boundary where the horizontal ionospheric current diverges.

Hoffman, R. A.↗

Welding torch with arc light reflector

A welding torch arc light reflector is disclosed for welding torches having optical viewing systems. A schematic of a welding torch having an internal coaxial viewing system consisting of a lens which focuses the field of view of the weld scene of the workpiece onto the end of the fiberoptic bundle is provided. The transmitted image of the fiberoptic bundle is provided to a camera lens which focuses it onto a TV sensor array for transmission. To improve the parity of the image of the monitoring system, an arc light reflector is shown fitted to the end of the torch housing or gas cup. The arc light reflector has an internal conical section portion which is polished to serve as a mirror which reflects the bright arc light back onto the darker areas of the weld area and thereby provides a more detailed image for the monitoring system. The novelty of the invention lies in the use of an arc light reflector on welding torches having optical viewing systems.

Gordon, Stephen S.↗

Jovian decametric arcs and Alfven currents

The Voyager Planetary Radio Astronomy (PRAD) experiment revealed prominent 'arcs' when the radio intensity at 1-40 MHz was displayed in time-frequency coordinates. These data are consistent with multiple currents flowing along longitudinally separated Jovian magnetic flux tubes, each current radiating conically at angles up to about 90 deg. The spacings between adjacent PRA arcs, and also between adjacent S burst arc segments observed at the Nancay Observatory, were analyzed and found to be so brief, less than 1-3 min, that either these currents and any associated Alfven waves survive for at least a few circulations of Jupiter by Io (a hypothesis independently supported by the observations of arcs at all Io phase angles), or each such Alfven current can radiate at several different cone-angles simultaneously (a hypothesis independently supported by the observation of such behavior in the S burst arcs).

Staelin, David H.↗

Numerical exploration of planetary arc dynamics

After analytically characterizing the response of a test particle to the combined effects of corotation and Lindblad resonances, due to the satellites of Neptune, as two coupled dynamical systems whose coupling depends on the collective effects in the arc, a formula is obtained for the energy imparted by the Lindblad resonance. This energy confines the arc material around the corotation resonance radius. The fact that the gradient of the torque density around the arc must be negative confirms the constraints defined by Lin et al. (1987) on the relative positions of the corotation and the Lindblad resonances if the arc is to be stable. These results are tested with a direct numerical simulation for two different arc configurations.

Sicardy, Bruno↗

An explanation for Neptune's ring arcs

The Voyager mission revealed a complex system of rings and ring arcs around Neptune and uncovered six new satellites, four of which occupy orbits well inside the ring region. Analysis of Voyager data shows that a radial distortion with an amplitude of approximately 30 kilometers is traveling through the ring arcs, a perturbation attributable to the nearby satellite Galatea. Moreover, the arcs appear to be azimuthally confined by a resonant interaction with the same satellite, yielding a maximum spread in ring particle semimajor axes of 0.6 kilometer and a spread in forced eccentricities large enough to explain the arc's 15-kilometer radial widths. Additional ring arcs discovered in the course of this study give further support to this model.

Porco, Carolyn C.↗

Solar cell arcing: The role of outgassing and contamination

The effect of outgassing, venting, and thruster firing events on spacecraft system performance has been a long standing issue. Recent laboratory measurements on negatively biased high voltage solar cells at Physical Sciences Inc. (PSI) suggest that some currently designed and certainly future space power systems must address/re-evaluate this issue. Our observations show that exposing these cells to moderate levels (10 exp -3 torr-min) of H2O vapor enhances the arcing frequency, while heating to 85 C to remove water vapor significantly reduces the arc frequency. The interaction of the adhesive used to attach the cover glass to the solar cell with ambient water vapor is the key factor in determining arcing rates. Elimination of adhesive exposed to the environmental plasma reduces the arc frequency more than two orders of magnitude, and eliminates any sensitivity to H2O exposure. The adhesive may also become a source of spacecraft contamination. Macroscopic amounts were observed to blow off some arc events, and (we assume) electrostatically precipitate at other negatively biased locations. Data, analysis, and potential impact for future space platforms are discussed.

Marinelli, W. J.↗

Arc-cathode interaction study

Insufficient electrode life and uncertainties in that life are major problems hampering the development in many plasma application areas which make use of plasma torches, arc heaters, and arc jet thrusters. In spite of a considerable amount of work published dealing with arc-cathode phenomena, our present understanding is still incomplete because different physical phenomena dominate for different combinations of experimental parameters. The objective of our present research project is to gain a better understanding of the behavior of arc-cathode surface interaction over a wide range of parameters, and furthermore to develop guidelines for better thermal design of the electrode and the selection of materials. This report will present the research results and progress obtained on the arc-cathode interaction studies at the University of Minnesota. It includes results which have been obtained under programs other than the NASA funded program. Some of the results have been submitted in an informal interim progress report, and all of the results have been presented in a seminar during a visit to the NASA Lewis Research Center on October 16, 1992.

Zhou, X.↗

A new giant luminous arc gravitational lens associated with a z = 0.62 galaxy cluster, and the environments of distant radio galaxies

In the course of a survey investigating the cluster environments of distant 3CR radio galaxies, I have identified a previously unknown 'giant luminous arc' gravitational lens. The lensing cluster is associated with the radio galaxy 3C 220.1 at z = 0.62 and is the most distant cluster now known to produce such arcs. I present imaging and spectroscopic observations of the cluster and the arc, and discuss the implications for the cluster mass. At z greater than 0.6 the cluster velocity dispersions implied by such giant arcs may provide an interesting constraint on theories of large scale structure formation. The parent investigation in which this arc was identified concerns galaxy clusters and radio galaxy environments at 0.35 less than z less than 0.8. At the present epoch, powerful FR 2 radio galaxies tend to be found in environments of poor or average galaxy density. In contrast, at the higher redshifts investigated here, richer group and cluster environments are common. I present additional data on other clusters from this survey, and discuss its extension to z greater than 1 through a program of near-infrared and optical imaging.

Dickinson, Mark↗

Gravitationally lensed arcs in two X-ray selected clusters of galaxies at z = 0.426 and z = 0.583

The discovery of two clusters of galaxies that contain new gravitationally lensed images (arcs) of high-redshift background galaxies is reported. Both clusters, MS1621.5+2640 and MS2053.7-0449, were selected from the Einstein Extended Medium Sensitivity Survey based on their high X-ray luminosity. V-band CCD images of the clusters taken in 0.5 arcsec seeing are presented, and it is shown that the arcs in both clusters are thin; they remain unresolved in width, but are fragmented along their length. The arc in MS1621.5+2640 has a small radius of curvature (about 7 arcsec), and spans about 70 deg centered near a 2.6 mJy radio galaxy that is not the brightest cluster galaxy. The arc in MS2053.7-0449 spans 40 deg at a radius of about 16 arcsec with a center slightly offset from the optically dominant cluster galaxy. The arc fragments into two clumps that appear to be stretched images of background galaxies.

Luppino, G. A.↗

Recycling of volatiles at subduction zones: Noble gas evidence from the Tabar-Lihir-Tanga-Feni arc of papua New Guinea

Convergent margin processes play an important but poorly understood role in the distribution of terrestrial volatile species. For example, subduction processes filter volatiles from the subducting package, thereby restricting their return to the mantle. In addition, once extracted from the downgoing slab, volatiles become an essential component in the petrogenesis of island arc magmas. The noble gases, with their systematic variation in physical properties and diversity of radiogenic isotopes, should carry a uniquely valuable record of these processes. However, thus far studies of noble gases in arc volcanics have achieved only limited success in this regard. Subduction-related lavas and geothermal fluids carry (3)He/(4)He ratios equal to or slightly lower than those found in the depleted upper mantle source of mid-ocean ridge basalts. Apparently slab-derived helium (which should have (3)He/(4)He much less than MORB) is extensively diluted by MORB-like helium from the mantle wedge, making it difficult to use helium as a tracer of convergent margin processes. Interpretation of the heavier noble gases (Ne-Ar-Kr-Xe) in arc lavas has also proven difficult, because the lavas carry low noble gas concentrations and hence are subject to pervasive atmospheric contamination. The low noble gas concentrations may be a consequence of degassing in the high level magma chambers characteristic of arc stratovolcanos. We have recently initiated a project to better constrain the behavior of volatiles in subduction zones through geochemical studies of the tectonically unusual volcanoes of the Tabar-Lihir-Tanga-Feni (TLTF) arc in the Bismarck Archipelago, Papua New Guinea.

Farley, Kenneth↗

Model study of multiple polar cap arcs: Occurrence and spacing

A new scenario for the formation of multiple polar cap arcs is proposed based on the results from a time-dependent electrodynamic model of polar cap arcs developed by Zhu et al. (1993). The results suggest that the appearance of multiple polar cap arcs may not be due to multiple structures in the magnetospheric source region, but instead, may primarily be determined by the coupled magnetosphere-ionosphere system in which the ionosphere plays an active role. It was found that with the same magnetospheric driver, a strong ionospheric background convection and an ionospheric background Hall conductance in the range of from 0.5 to 1.5 mho favor the occurrence of multiple polar cap arcs. It was also found that the spacing between individual arcs is highly correlated with the ratio of the enhanced Hall and Pedersen conductances (i.e., the hardness of the primary magnetospheric precipitation), which is allowed to vary in the model runs. A harder precipitation causes a wider spacing. In the modelings, the spacing ranged from about 20 kilometers to about 60 kilometers when the precipitation hardness increased.

Zhu, L.↗

An advanced arc track resistant airframe wire

Tensolite, a custom cable manufacturer specializing in high temperature materials as the dielectric medium, develops an advance arc track resistant airframe wire called Tufflite 2000. Tufflite 2000 has the following advantages over the other traditional wires: lighter weight and smaller in diameter; excellent wet and dry arc track resistance; superior dynamic cut-through performance even at elevated temperatures; flight proven performance on Boeing 737 and 757 airplanes; and true 260 C performance by utilizing Nickel plated copper conductors. This paper reports the different tests performed on Tufflite 2000: accelerated aging, arc resistance (wet and dry), dynamic cut through, humidity resistance, wire-to-wire abrasion, flammability, smoke, weight, notch sensitivity, flexibility, and markability. It particularly focuses on the BSI (British Standards Institute) dry arc resistance test and BSI wet arc tracking.

Beatty, J.↗

Electromagnetic radiation generated by arcing in low density plasma

An unavoidable step in the process of space exploration is to use high-power, very large spacecraft launched into Earth orbit. Obviously, the spacecraft will need powerful energy sources. Previous experience has shown that electrical discharges occur on the surfaces of a high-voltage array, and these discharges (arcs) are undesirable in many respects. Moreover, any high voltage conductor will interact with the surrounding plasma, and that interaction may result in electrical discharges between the conductor and plasma (or between two conductors with different potentials, for example, during docking and extravehicular activity). One very important aspect is the generation of electromagnetic radiation by arcing. To prevent the negative influence of electromagnetic noise on the operation of spacecraft systems, it seems necessary to determine the spectra and absolute levels of the radiation, and to determine limitations on the solar array bias voltage that depend on the parameters of LEO plasma and the technical requirements of the spacecraft equipment. This report describes the results of an experimental study and computer simulation of the electromagnetic radiation generated by arcing on spacecraft surfaces. A large set of high quality data was obtained during the Solar Array Module Plasma Interaction Experiment (SAMPIE, flight STS-62) and ground test. These data include the amplitudes of current, pulse forms, duration of each arc, and spectra of plasma waves. A theoretical explanation of the observed features is presented in this report too. The elaborated model allows us to determine the parameters of the electromagnetic noise for different frequency ranges, distances from the arcing site, and distinct kinds of plasma waves.

Vayner, Boris V.↗

Electric Arc and Electrochemical Surface Texturing Technologies

Surface texturing of conductive materials can readily be accomplished by means of a moving electric arc which produces a plasma from the environmental gases as well as from the vaporized substrate and arc electrode materials. As the arc is forced to move across the substrate surface, a condensate from the plasma re-deposits an extremely rough surface which is intimately mixed and attached to the substrate material. The arc textured surfaces produce greatly enhanced thermal emittance and hold potential for use as high temperature radiator surfaces in space, as well as in systems which use radiative heat dissipation such as computer assisted tomography (CAT) scan systems. Electrochemical texturing of titanium alloys can be accomplished by using sodium chloride solutions along with ultrasonic agitation to produce a random distribution of craters on the surface. The crater size and density can be controlled to produce surface craters appropriately sized for direct bone in-growth of orthopaedic implants. Electric arc texturing and electrochemical texturing techniques, surface properties and potential applications will be presented.

Banks, Bruce A.↗

X-Ray Gas Temperatures in the Arc Clusters MS0440+204 and MS0302+1658

The cluster of galaxies MS0440+02, originally discovered through its X-ray emission, was part of an optical observational program to search for arcs and arclets in a complete sample of X-ray luminous, medium-distant clusters of galaxies. Mauna Kea CCD images of MS0440+02 showed a remarkable optical morphology. The core of the cluster contains 6 bright galaxies and numerous fainter ones embedded in a low surface brightness halo. Besides, MS0440+02 is the most spectacular example that we have found of an arc system in a compact condensed cluster, with arcs symmetrically distributed to draw almost perfect circles around the cluster center. Giant arcs are magnified images of distant galaxies, gravitationally distorted by massive foreground clusters. It is of great importance to compare the results of the lensing studies with those derived from X-ray observations, as the two are independent methods of studying the mass distribution. Thus MS0440+02 was the ideal target to obtain temperature measurement with ASCA and good spatial resolution X-ray observations with ROSAT. The X-ray data have been used in conjunction with Hubble Space Telescope observations to put more stringent constrains on the mass estimates. Most of the different wavelength datasets have been reduced and analyzed. Mass determinations have been separately obtained from galaxy virial motions and X-ray profile fitting using the cluster gas temperature as measured by the ASCA satellite. Assuming that the hot gas is in hydrostatic equilibrium and in a spherical potential, we find from the X-ray data a mass distribution profile that is well described by a Beta model. From the multiple images formed by gravitational lensing (HST data) using the modelling of the gravitational lensed arcs, we have derived Beta model. To reconcile the mass estimates we have explored the possibility of having a supercluster surrounding the MOS0440 cluster, that is a model with two isothermal spheres, one embedded inside the other. These results have been published or are in press.

Gioia, Isabella M.↗

Preliminary Development of Electrodes for an Electric-Arc Wind Tunnel

Two electrode configurations were tested in an electric-arc wind tunnel at the NASA Lewis Research Center. The results indicated approximately the same heat-loss rate per unit of arc power input for each of the configurations. Measured heat-loss rates were on the order of 40 percent of the arc power input. Nearly all this loss occurred at the anode. The power input and arc current limitations of the electrodes appear to be the critical design factors. Up to now, the maximum power to the stream has been 115 kilowatts with a cooled tungsten cathode and a cooled cylindrical anode incorporating a magnetic field. The maximum power input to this anode could not be established with the cooled tungsten cathode because cathode failures occurred at a gross power level of approximately 175 kilowatts. It was necessary to use a graphite cathode to seek the limitation of the anode. The results indicated that the anode limitation was primarily a function of arc current rather than power input. The anode was successfully operated at a power of 340 kilowatts at 1730 amperes; however, the anode failed with a power input of 324 kilowatts and a current of 2140 amperes. The magnetic flux density at the time of failure was 0.32 weber per square meter, or 3200 gauss. The graphite cathode was used only to establish the anode limitation; further investigation of graphite cathodes was discontinued because of the large amount of stream contamination associated with this type of electrode.

Shepard, Charles E.↗

Short-Arc Analysis of Intersatellite Tracking Data in a Gravity Mapping Mission

A technique for the analysis of low-low intersatellite range-rate data in a gravity mapping mission is explored. The technique is based on standard tracking data analysis for orbit determination but uses a spherical coordinate representation of the 12 epoch state parameters describing the baseline between the two satellites. This representation of the state parameters is exploited to allow the intersatellite range-rate analysis to benefit from information provided by other tracking data types without large simultaneous multiple data type solutions. The technique appears especially valuable for estimating gravity from short arcs (e.g., less than 15 minutes) of data. Gravity recovery simulations which use short arcs are compared with those using arcs a day in length. For a high-inclination orbit, the short-arc analysis recovers low-order gravity coefficients remarkably well, although higher order terms, especially sectorial terms, are less accurate. Simulations suggest that either long or short arcs of GRACE data are likely to improve parts of the geopotential spectrum by orders of magnitude.

Rowlands, David D.↗