Search NASA⌕ Search

SEARCH · Search NASA

Results for “Adhesion Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Understanding and Overcoming Water-induced Interfacial Degradation in Si Modules (Final Technical Report)

Moisture ingress is an established issue for photovoltaic module durability. Durability studies probing moisture effects typically evaluate performance losses at the module level, attributing global power losses to the overall humidity condition of the test environment while leaving local module behavior unknown. This project successfully develops an in situ short-wave infrared probe of moisture content in PV modules with demonstrated detection limits better than 100 ppm in EVA-encapsulated Al-BSF and PERC architectures (66 µg/cm3) and applicability across the range of terrestrial conditions. Combining this optical moisture quantification method (water reflectometry detection, WaRD) with peel testing of interfaces, biased photoluminescence imaging of performance, and first principles computation, we correlate module moisture content and cell performance over the course of accelerated damp heat tests. By performing multi-level humidity and thermal accelerated testing over thousands of hours (0, 65 and 85% RH and 25, 65, and 85°C), we are able to attribute effects of individual environmental stresses and the dependence on module architecture. Using first-principles computational chemistry, we find that the decomposition of EVA to acetic acid (Norrish II) is thermodynamically preferred over a pathway to acetaldehyde (Norrish I), elucidating the underlying chemistry of encapsulant degradation. We also find it is likely that water segregates to the stable interfaces of the cell, especially the SiNx/EVA interface. We find that moisture is strongly correlated with reduction in adhesion at the interfaces of the cells, particularly at Ag fingers. We show uniquely that the peel strength required to delaminate the encapsulant from the front of the cell depends not only on the exposure to a high heat and humid environment, but also to the moisture content during the mechanical testing, indicating an important interaction between when mechanical stresses are faced in terms of the moisture content of the module and its durability. We find that the background sheet resistance (that is, the sheet resistance rise not attributable to finger interruptions or cracks) is substantially higher in the backsheet mini-modules vs glass-glass packages when humidity and temperature are faced. This increase in power loss due to the background resistance increase over time in damp heat in glass-backsheet modules resulted in ~3-4% larger decrease in relative PCE compared to glass-glass modules. In glass-backsheet modules, the effect of the moisture dose alone is comparable or greater than that of the combined temperature and water term, suggesting that glass-backsheet modules are overall more susceptible to moisture induced performance loss. Finally, we show that thin film PV modules are amenable to WaRD measurement, based on the ability to detect moisture in POE encapsulants or in the cell stack itself. The ease of WaRD measurement and its few requirements on the bill of materials should enable broad applicability of this technique for studying the effects of moisture in PV.

14 SOLAR ENERGY↗
DOE OSTI2025

Trade-offs at the interface

The durability of perovskite solar cells is closely linked to the mechanical adhesion toughness of their interfaces, though some toughening strategies could trigger detrimental chemical reactions. Here, research now shows that this trade-off can be effectively managed through interfacial engineering, informed by innovative mechanical testing.

14 SOLAR ENERGY↗
DOE OSTI2023

Design, Manufacture, and Testing of an Open-Source Benchmark Composite Hydrokinetic Turbine Blade: Preprint

In a trend toward clean energy alternatives, recent years have seen great strides in the marine energy space. Consequently, there is a pressing need for the design, development, and validation of novel energy harvesting technologies such as hydrokinetic devices, which capture kinetic energy from waves, tides, and currents. However, these devices span numerous concepts and designs that often lack solid benchmark research that can be freely referenced throughout their development. This work focuses on the design process of an open-source composite hydrokinetic turbine blade for a three-bladed marine turbine rotor assembly with a diameter of 2.5 m. The proposed blade consists of two structural composite skins that are bonded with an adhesive and filled with a foam core. This study also explores and contrasts the efficiency and resolution of low-fidelity rapid design methodologies and comprehensive high-fidelity approaches in the context of blade design, modeling, and analysis efforts, a key objective in this research. Blade hydrodynamic loads were modeled and applied to finite-element blade models to study deformations and potential failure. Ongoing and upcoming efforts will result in blade manufacture and structural testing at the National Renewable Energy Laboratory. In future work, multiple blades will be deployed at the Living Bridge site at the University of New Hampshire and will be compared to rigid aluminum blades of the same geometry, developed by Sandia National Laboratories. Ultimately, this research will lay foundational groundwork for researchers and manufacturers, establishing a baseline composite blade design that will serve as a benchmark in the development of future hydrokinetic turbine blades.

blade design↗
DOE OSTI2024

Low-Cost, High-Performance Carbon Fiber for Compressed Natural Gas Storage Tanks (Final Technical Report – Down Select Report)

The aim of this project is to reduce the cost of Type IV, carbon fiber (CF) composite overwrap compressed gas storage tanks by reducing the cost of CF and CF composites. The project team worked to reduce the cost of CF by exploring and testing opportunities for a low-cost alternative precursor material for CF production to supplant market-dominant and costly polyacrylonitrile (PAN). Concurrently, the team aimed to reduce the cost of the tanks at the composite level by improving the interfacial adhesion between the fibers and the matrix resin through the incorporation of low-cost nanoparticles recycled from waste materials, which would reduce the volume of costly CF required to achieve the same tank performance. At the end of the first year, the project team selected mesophase pitch as the primary precursor candidate from a field of materials based on the superior mechanical performance and cost-saving potential. During the second year, the team produced CFs derived from mesophase pitch achieving an average tensile strength of 365.6 ksi and average tensile modulus of 40.74 Msi. Facility availability for spinning and converting these fibers at greater scale has hindered scale-up demonstration, but the team has identified opportunities to conduct this work in the near term. Cost modeling shows that these mesophase pitch-derived CFs can be up to 40% less expensive than PAN-derived CFs due to the lower cost of the feedstock material, higher throughput, greater conversion yield, and lower cost spinning method and compared to PAN. Additionally, the team has demonstrated at lab-scale that nanoparticle coating CFs can significantly increase the interfacial shear strength and load transfer efficiency of CFs in a matrix. Single filament pull-out testing showed a 27% average increase in max interfacial shear strength due to this coating. A continuous method of applying these coatings to a tow of CF has been developed for scale-up. 26 m tows of coated CFs were produced using this system and formed into composite ring samples for ASTM ring burst testing. Issues with the testing protocol have limited assessment of these results. A prototype Type IV tank was designed to meet ANSI HGV2 standards, and the design criteria set out by DOE, using the CF properties developed by the team paired with a proprietary resin matrix, a polyamide liner, and aluminum end bosses. The tank weighs 153.1 kg and with a total capacity of 5.8 kg H2 (5.6 kg usable), which yields a gravimetric capacity of 1.17 kWh/kg. Cost modeling predicts that the tank will have a projected cost of $15.73/kWh. Tank performance modeling does not include considerations for fiber-matrix load transfer efficiency improvements offered by nanoparticle coating method.

08 HYDROGEN↗
DOE OSTI2021

Qualification of 3-D Printed Mortar With Electrical Conductivity Measurements

Additive manufacturing (AM) or 3D printing of concrete allows for construction of arbitrary shape structures without a mold. Since reproducibility of 3D printed concrete is lower than that of conventional fabrication, each 3D printed structure should be monitored for proper curing. Conventional qualification of concrete is based on several tests, including destructive compressive strength measurements. Because a structure is 3-D printed layer-by-layer, the surfaces of AM concrete structures have significant surface roughness. This limits the applicability of conventional nondestructive testing methods. We investigated qualification of 3D printed mortar by monitoring curing with nondestructive electrical conductivity measurements. Bulk resistance of concrete was extracted from electrochemical impedance spectroscopy (EIS measurements made using custom flexible self-adhesive electrodes, which contour to rough surfaces. We show that bulk resistivity of concrete increases linearly with time. This allows for developing a calibration curve for compressive strength lookup from nondestructive electrical conductivity measurements. Conductivity measurements also allow for estimation of formation factor, which is an indicator of mortar permeability.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Independence of Environmental and Mechanical Damages on Silicone Adhesive Stored in a Thermo-Oxidative Environment

Abstract Elastomeric polymer materials hold a special place in today’s industrial sectors with respect to structural application needs. Low quality materials are detrimental to industries like aerospace, and automotive engineering. Assessment of the durability of elastomers for structural applications has been of much interest among the literary circles for decades and new materials keep outperforming the existing ones. Polymeric adhesives are one of the most abundantly used materials in these industries. All polymeric materials get damaged when in contact with aggressive environments in presence of high temperature and oxygen. Commonly referred to as thermo-oxidation, this environment exposes the material to heat and oxidation reactions in presence of oxygen. Resultantly, during service life, the damage to the polymer matrix is primarily caused by two factors: mechanical damage and environmental aging. Environmental aging is an irreversible phenomenon caused by changes in the molecular structure while mechanical damage maintains the shape of the polymer matrix, and the deterioration is mostly due to polymer chain mobility. Environmental aging can be caused by a single environmental agent or by a synergized impact of several environmental elements. Increasing temperature is found to be proportional to decreasing tensile strength and toughness of material. The rate and extent of degradation can be accessed by scrutinizing the changes in constitutive behavior of material through mechanical and chemical properties. Accelerated thermal aging is among the most common modes of process related degradation, leading generally to chain scission, and crosslinking phenomena and reduced resistance to fracture stress, and strain. In this experimental study, our goal is to separate the environmental degradation from mechanical damage. A silicone-based adhesive was aged in thermo-oxidative at (0%RH) aging environment. The damage and decay mechanisms have been used to draw a distinction between environmental degradation and mechanical damage. Material characterization included uniaxial tensile test (failure and cyclic) and scanning electron microscopy (SEM) tests on as-received and aged samples. Aging was conducted at three different temperatures (60°C, 80°C and 95°C) and six different exposure durations (1, 3, 10, 30, 90 and 200 days). This work confirms that environmental damage is superposed on top of the mechanical damage, and thus, they are separable. The total mechanical and environmental damage is a synergized effect of all exposure conditions and parameters involved i.e., aging time, temperature, and oxygen. The chemistry and mechanics of the polymer degradation were found to be in good agreement with each other.

Alazhary, Sharif↗
DOE OSTI2021

Tribological behavior of ceramic-alloy bearing contacts in molten salt lubrication for concentrating solar power

Molten salts are considered as candidate heat transfer fluids and thermal energy storage media for next generation concentrating solar power (CSP). A molten salt circulates inside the piping and heat exchanger and also functions as a lubricant for the sleeve bearings of the CSP pump. Furthermore, wear- and corrosion-resistant high-temperature bearing materials are critical for the pump efficiency and durability. This study evaluated the tribological performance of candidate bearing materials in lubrication of a molten chloride salt mixture (20% NaCl + 40% MgCl 2 + 40% KCl) at 750 °C in an inert argon gas (a simulative CSP pump environment). Six ceramic-alloy pairs were tested, zirconia and silicon nitride against Haynes 244, Hastelloy C276, and Tribaloy T900 alloy, and ranked by the friction coefficient and wear loss. Characterization of worn surfaces suggested the wear mechanism as a combination of abrasion, adhesion, and tribocorrosion. Results from this study provide fundamental insight for the development and selection of bearing materials for molten salt powered CSP pumps.

14 SOLAR ENERGY↗
DOE OSTI2024

Anti-reflection coating with mullite and Duroid for large-diameter cryogenic sapphire and alumina optics

We developed a broadband two-layer anti-reflection (AR) coating for use on a sapphire half-wave plate (HWP) and an alumina infrared (IR) filter for the cosmic microwave background (CMB) polarimetry. Measuring the faint CMB B-mode signals requires maximizing the number of photons reaching the detectors and minimizing spurious polarization due to reflection with an off-axis incident angle. Sapphire and alumina have high refractive indices of 3.1 and are highly reflective without an AR coating. This paper presents the design, fabrication, quality control, and measured performance of an AR coating using thermally sprayed mullite and Duroid 5880LZ. This technology enables large optical elements with diameters of 600 mm. We also present a thermography-based nondestructive quality control technique, which is key to assuring good adhesion and preventing delamination when thermal cycling. We demonstrate the average reflectance of about 2.6% (0.9%) for two observing bands centered at 90/150 (220/280) GHz. At room temperature, the average transmittance of a 105 mm square test sample at 220/280 GHz is 83%, and it will increase to 90% at 100 K, attributed to reduced absorption losses. Therefore, our developed layering technique has proved effective for 220/280 GHz applications, particularly in addressing dielectric loss concerns. This AR coating technology has been deployed in the cryogenic HWP and IR filters of the Simons Array and the Simons observatory experiments and applies to future experiments such as CMB-S4.

Sakaguri, Kana (ORCID:0000000156678118)↗
DOE OSTI2022

Investigation of the Interactions Between Low-Temperature Ag Paste Components and SiO2/Poly-Si(n) Contacts and the Impact on Contact Properties

Reducing poly-Si thickness to minimize parasitic absorption on a light-receiving side of a TOPCon solar cell without suffering voltage losses after metallization is a challenge in optimizing TOPCon performance. As an alternative to fire-through pastes, we investigate low-temperature Ag paste to SiO2/poly-Si passivating contacts through fabrication of electrical test structures to characterize the passivation quality and electrical transport across the metallized interface. With current paste chemistries, we find that solvent wetting of the poly-Si surface before evaporation and non-volatile binder resin adhesion to the surface after curing are major impediments which prevent Ag contact formation. However, low- resistance poly-Si/Ag interfaces formed with physical vapour deposition similarly degrade after annealing, indicating contacting issues related to the Ag content even in the absence of the organic paste components.

low temperature Ag paste↗
DOE OSTI2026

Designing carbon wetting layers with inorganic salts as additives for enhanced adhesion and molten sodium wettability in electrochemical application

ß” alumina solid-state electrolyte (BASE) is considered one of the most promising materials for sodium batteries due to its high ionic conductivity and exceptional stability with molten sodium. However, at lower operating temperatures, the poor physical contact at the liquid-solid interface between molten sodium and BASE results in high interfacial resistance. In this study, we explore the optimization of carbon wetting layers with various salt additives to enhance adhesion and improve molten sodium wettability. Using a spray-coating method, carbon layers incorporating sodium hexametaphosphate (Na6(PO3)6, SHMP) as an additive demonstrate superior adhesion, mechanical stability, and enhanced wettability with molten sodium. Scanning Electron Microscopy (SEM) analysis reveals that SHMP preserves the porous carbon network required for efficient sodium transport while minimizing structural defects such as cracks and voids. Electrochemical testing using Na symmetric cells confirms that SHMP-modified layers significantly reduce interfacial resistance and overpotential, outperforming No salts counterparts. These findings highlight that the strategic incorporation of suitable additives, such as SHMP, in the design of microscale carbon layers could significantly enhance the performance of molten sodium batteries at lower operating temperatures.

Han, Henry H.↗
DOE OSTI2024

Covalently-Bonded Laminar Assembly of Van der Waals Semiconductors with Polymers: Toward High-Performance Flexible Devices

Van der Waals semiconductors (vdWS) offer superior mechanical and electrical properties and are promising for flexible microelectronics when combined with polymer substrates. However, the self-passivated vdWS surfaces and their weak adhesion to polymers tend to cause interfacial sliding and wrinkling, and thus, are still challenging the reliability of vdWS-based flexible devices. Here, in this study, an effective covalent vdWS–polymer lamination method with high stretch tolerance and excellent electronic performance is reported. Using molybdenum disulfide (MoS 2 ) and polydimethylsiloxane (PDMS) as a case study, gold–chalcogen bonding and mercapto silane bridges are leveraged. The resulting composite structures exhibit more uniform and stronger interfacial adhesion. This enhanced coupling also enables the observation of a theoretically predicted tension-induced band structure transition in MoS 2 . Moreover, no obvious degradation in the devices’ structural and electrical properties is identified after numerous mechanical cycle tests. This high-quality lamination enhances the reliability of vdWS-based flexible microelectronics, accelerating their practical applications in biomedical research and consumer electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Biocompatible Electrostatic Layered Systems for Viral Elimination in the Nose/Throat

An anti-viral coating for the nose & throat is needed to quickly address the spread of COVID-19 infections and to aid future pandemics. Current nasal delivery systems are typically a 1-spray homogenous solution, which is convenient but may not be as efficient or durable as a multi-spray solution that contains a binding layer to anchor the anti-viral components. Many of the current nasal solutions being investigated to aid in pandemic response have solution-based mechanisms of action and are quickly cleared from the nose/mouth limiting their efficacy lifetime. A multi-spray approach utilizing strong intermolecular forces between polymeric materials and anti-viral agents to provide a robust biocompatible coating is expected to have increased physical and chemical properties to combat viral infection. This work evaluated which tailored biocompatible materials are needed to generate a layered system to combat viral infection. This layered system takes advantage of electrostatic interactions to bind anti-viral components, shown in Figure 1. Proof of concept success was demonstrated through cell toxicity studies and anti-viral assays on both the individual layer components and the complete layered system. Project work began with chemical modifications of Xantham Gum to hydrolyzing xanthan gum to give a negatively charged polymer with varying degrees of ionic character and investigate bonding efficiencies. However, this was abandoned in favor of comparing COTS available materials listed in Table 1 (Results section). Concentration and adhesion studies were performed on layers created using the listed polymeric materials and anti-viral agents. Finally, biocompatibility of materials, layers, and coating system were confirmed through cytotoxicity studies and the efficacy of the anti-viral properties tested with phi6 bacteriophage as a SARS-CoV2 surrogate.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Lamination of transparent conductive adhesives for tandem solar cell applications

A transparent conductive adhesive (TCA) interlayer for mechanically stacked multijunction solar cells provides adhesive strength and electrical connection between sub-cells when stacked. The fabrication of TCA sheets from an ethyl-vinyl acetate (EVA) matrix and silver coated compliant conductive microspheres, similar to industry-standard EVA encapsulant sheets, compatible with a standard lamination process was developed. Blade coating TCA sheets using 3D printed blades and testing of vertical conduction through the interlayer with a TCA conductivity jig allowed for reproducible measurements and low-cost fabrication. The supplemental information provides design files to enable other researchers to produce their own blades and testing jigs. We identified 0.5 mm as an optimal blade height for producing lab-scale TCA sheets and 120 °C at 3 psi for 10 min as the optimal vacuum lamination process to minimize resistance and possible damage to samples. For TCA sheets with coverages between 0.75% and 9%, the series resistance was approximately 0.2 O cm2 which should result in minimal losses for one-sun photovoltaic applications.

14 SOLAR ENERGY↗
DOE OSTI2024

Designing metal halide perovskite solar modules for thermomechanical reliability

There is a significant deficiency in perovskite solar module (PSM) stability under thermomechanical stressors which is not well-understood. In this perspective, common issues seen with perovskite solar cell device fabrication related to thermomechanical reliability of PSM processing are discussed, with a focus on how the robustness of device layers and interlayer adhesion can be improved. Film stresses, adhesion of charge transport layers, and instability under light and heat are discussed with the purpose of providing insight on designing PSMs for durability. Processing conditions of encapsulation of PSMs and critical parameters to consider are also examined, and accelerated testing protocols for PSMs are discussed that probe mechanical degradation modes and ensure reliability of devices in the field.

14 SOLAR ENERGY↗
DOE OSTI2021

Adhesive Bonding of Copper Prepared by Laser-Interference near the Interference Structuring Limits

Adhesive bonding requires adequate surface preparation for ensuring an appropriate joint quality. The interest in adhesive joining has recently expanded to thermal systems having a large number of joints employed for manufacturing and assembly. This study presents surface topology of copper 110 produced by a laser-interference setup that would theoretically yield a periodicity of 1.7 μm, which is near the 1.6–2 μm structuring limit that was estimated based on thermal diffusion length scale for an 8 ns laser pulse. The results show that although the expected periodic interference structuring was not attained, the melt-induced texturing was affected by the laser-interference profile. Single-lap shear tests were performed with specimen surfaces prepared by traditional abrasion and laser-interference structuring methods. Several laser processing parameters, such as the laser spot size, density, number of pulses, and raster speed, were studied. Scanning electron microscope and profilometry measurements were used to characterize the processed surface microstructures. Web-like structures, which indicate widespread melting, were shown to be formed at different processing conditions. Based on the surface topologies investigated, two laser raster speeds were selected to make single-lap-joint specimens. Baseline joints were prepared by abrading joining specimens. The shear-lap strength and displacement at maximum load were shown to be higher by 16.8% and 43.8% for the laser-structured specimens than those of the baseline specimens, respectively. Moreover, the load-displacement curves indicated that the laser-structured joints were more ductile than those without laser-structuring. The increased ductility for the laser-structured joints was found to yield an increase in the energy absorbed during shear-lap testing of approximately of 80–90% over those measured for baseline joints. It is another indicator that laser-interference structuring enhanced the bonding performance of single-lap shear joints.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical Performance and Mesostructure Analysis of Proton-Irradiated Fused Filament Fabrication Acrylonitrile Butadiene Styrene Material

The use of fused filament fabrication (FFF) acrylonitrile butadiene styrene (ABS) and other thermoplastics in radiation environments is beginning to be studied as possible replacements for traditionally manufactured parts and tools. Interlayer adhesion within the mesostructure has been shown in published literature to be an integral component in the strength of FFF ABS. Research of irradiated 3D printed polymers has primarily focused on the influence of gamma irradiation on the mechanical properties of FFF ABS samples, without evaluating its impact on the mesostructure of the samples. The purpose of this paper is to understand the mechanical damage caused by proton radiation on FFF ABS samples through the evaluation of the mesostructure of the ABS samples. To achieve this objective, proton radiation at 40 MeV was applied to FFF ABS samples at radiation doses up to 1.0 MGy at a dose rate of 1 MGy/hr. Following the irradiation, tensile testing was performed on the samples. Here, the fractured surfaces of the tested samples were subsequently observed using a scanning electron microscope. The mechanical test results show an increase in the ultimate tensile strength (UTS) and a decrease in the ductility of the irradiated samples. Statistical analysis on the results shows that there is a statistically significant difference in the UTS and the ductility of unirradiated and 1.0 MGy irradiated samples and between irradiated samples and 1.0 MGy samples. In addition, the percentage elongation at break has statistically significant differences in the means between irradiated samples and 1.0 MGy samples. The UTS has statistically significant differences in the means between 0.1 MGy and 1.0 MGy. The difference in the means between the unirradiated and the 1.0 MGy samples is the most significant for both the UTS and elongation at break. The scanning electron microscopy (SEM) results indicated that interlayer adhesion improved as a function of radiation dose corresponding to the increase in tensile strength. The SEM results also showed that crazing and plastic deformation were reduced; aligning with the loss in ductility observed in the tensile tests results. The proton radiation is causing these mechanical and physical changes through two mechanisms: (1) dose rate effects on ionizing radiation-induced oxidative degradation; and (2) radiation heating effects of high energy (>1 MeV) charged particles.

electron microscopy↗
DOE OSTI2020

A novel fiber-fretting test for tribological characterization of the fiber/matrix interface

Ceramic matrix composites exhibit excellent high temperature properties and are candidate materials for structural applications from jet engines to nuclear fuel cladding. The strength and deformation behavior of these composites are intrinsically tied to the properties of the fiber/matrix interface. This research introduces a novel technique to evaluate the fundamental friction and wear characteristics of these interfaces. A case study on SiC f /PyC/SiC m composites applies in situ fiber fretting to investigate the kinetic friction coefficient and cyclic wear characteristics of the interphase. The experimental methodology is presented in explicit detail to encourage other researchers to explore the capabilities of this technique. Additionally, testing was carried out as a function of fiber roughness, PyC thickness (≈10, 500, 1200 nm), cycle count (10, 100, 1000), and frequency (1, 5, and 10 Hz). The friction coefficient and wear behavior changed with cycle length due to a transition from adhesive to abrasive mechanisms. SEM fractography provided insights to tribological evolution from adhesive sliding to three-body abrasive wear. The structural disorder at the tribo-surface relating to graphitic content and dangling bond density was investigated using Raman spectroscopy. Properties are contextualized with comparison to uniaxial tensile behavior of the parent composite.

36 MATERIALS SCIENCE↗