Search NASA⌕ Search

SEARCH · Search NASA

Results for “Alloy 718”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Effect of cryogenic irradiation on NERVA structural alloys

Several alloys (Hastelloy X, AISI 347, A-286 bolts, Inconel 718, Al 7039-T63 and Ti-5Al-2.5Sn ELI) were irradiated in liquid nitrogen (140 R) to neutron fluences between 10 to the 17th power and 10 to the 19th power nvt (E greater than 1.0 Mev). After irradiation, tensile properties were obtained in liquid nitrogen without permitting any warmup except for some specimens which were annealed at 540 R. The usual trend of radiation damage typical for materials irradiated at and above room temperature was observed, such as an increase in strength and decrease in ductility. However, the damage at 140 R was greater because this temperature prevented the annealing of radiation-induced defects which occurs above 140 R.

Dixon, C. E.↗
NASA NTRS1988

Fatigue life prediction modeling for turbine hot section materials

This paper presents a summary of the life prediction methods developed under the NASA Lewis Research Center's Hot Section Technology (HOST) program. A major objective of the fatigue and fracture efforts under the HOST program was to significantly improve the analytic life prediction tools used by the aeronautical gas turbine engine industry. This has been achieved in the areas of high-temperature thermal and mechanical fatigue of bare and coated high-temperature superalloys. Such technical improvements will eventually reduce life cycle costs. The cyclic crack initiation and propagation resistance of nominally isotropic polycrystalline alloys and highly anisotropic single crystal alloys has been addressed. A sizeable data base has been generated for three alloys [cast PWA 1455 (B-1900 + Hf), wrought Inconel 718, and cast single crystal PWA 1480] in bare and coated conditions. Two coatings systems, diffusion aluminide (PWA 273) and plasma sprayed MCrAIY overlay (PWA 286) were employed. Life prediction modeling efforts were devoted to creep-fatigue interaction, oxidation, coatings interactions, multiaxiality of stress-strain states, mean stress effects, cumulative damage, and thermomechanical fatigue. The fatigue crack initiation life models developed to date include the Cyclic Damage Accumulation (CDA) Model of Pratt & Whitney and the Total Strain Version of Strainrange Partitioning (TS-SRP) of NASA Lewis for nominally isotropic materials, and the Tensile Hysteretic Energy Model of Pratt & Whitney for anisotropic superalloys. The fatigue model being developed by the General Electric Company is based upon the concepts of Path-lndependent Integrals (PII) for describing cyclic crack growth under complex nonlinear response at the crack tip due to thermomechanical loading conditions. A micromechanistic oxidation crack extension model has been derived by researchers at Syracuse University. The models are described and discussed in the paper. Only limited verification has been achieved to-date as several of the technical programs are still in progress and the verification tasks are scheduled, quite naturally, near the conclusion of the program. To-date, efforts have concentrated on development of independent models for cyclic constitutive behavior, cyclic crack initiation, and cyclic crack propagation. The transition between crack initiation and crack propagation has not been thoroughly researched as yet, and the integration of these models into a unified life prediction method has not been addressed.

Metal fatigue↗
NASA NTRS2001

Behavior of Three Metallic Alloys Under Combined Axial-Shear Stress at 650 C

Three materials, Inconel 718, Haynes 188, and 316 stainless steel, were tested under an axial-torsional stress state at 650 C. The objective of this study was to quantify the evolution of the material while in the viscoplastic domain. Initial and subsequent yield surfaces were experimentally determined to quantify hardening. Subsequent yield surfaces (yield surfaces taken after a preload) had a well-defined front side, in the prestrain direction, but a poorly defined back side, opposite the prestrain direction. Subsequent yield surfaces exhibited isotropic hardening by expansion of the yield surface, kinematic hardening by translation of the yield surface, and distortional hardening by flattening of the yield surface in the direction opposite to the last prestrain. An existing yield function capable of representing isotropic, kinematic, and distortional hardening was used to fit each yield surface. Four variables are used to describe each surface. These variables evolve as the material state changes and have been regressed to the yield surface data.

Colaiuta, Jason F.↗
NASA NTRS1989

High performance alloy electroforming

Electroformed copper and nickel are used in structural applications for advanced propellant combustion chambers. An improved process has been developed by Bell Aerospace Textron, Inc. wherein electroformed nickel-manganese alloy has demonstrated superior mechanical and thermal stability when compared to previously reported deposits from known nickel plating processes. Solution chemistry and parametric operating procedures are now established and material property data is established for deposition of thick, large complex shapes such as the Space Shuttle Main Engine. The critical operating variables are those governing the ratio of codeposited nickel and manganese. The deposition uniformity which in turn affects the manganese concentration distribution is affected by solution resistance and geometric effects as well as solution agitation. The manganese concentration in the deposit must be between 2000 and 3000 ppm for optimum physical properties to be realized. The study also includes data regarding deposition procedures for achieving excellent bond strength at an interface with copper, nickel-manganese or INCONEL 718. Applications for this electroformed material include fabrication of complex or re-entry shapes which would be difficult or impossible to form from high strength alloys such as INCONEL 718.

Malone, G. A.↗
NASA NTRS1990

Approach to SSME health monitoring. II - Exhaust plume emission spectroscopy at the DTF

The Diagnostics Testbed Facility (DTF) located at the Stennis Space Center (SSC) is used for obtaining extensive sets of H2O2 exhaust plume emission spectral data for the SSME critical components related elements and materials. The SSME related elements and materials are simulated by mixing appropriate amounts of compounds of their respective constituent elements in an aqueous solution which is injected into the combustion chamber of the DTFT. Five of the most critical components of the SSME which have experienced very severe wear and tear problems in the past are analyzed. These are high pressure turbopump (HPTP) turbine blades, HPTP turbine disks, HPTP bearing, main injector LOX posts, and the main combustion chamber structural shell. The alloys used in the manufacturing of these components are MAR-M 246 + Hf, Waspaloy X, AISI 440C, Haynes 188, and Inconel 718, respectively. The experimental setup and procedures at the DTF are described; stratospheric data for the five alloys are presented; and strategies for the material identification in the SSME exhaust plume are discussed.

Tejwani, Gopal D.↗
NASA NTRS1978

Computer-aided analysis and design of the shape rolling process for producing turbine engine airfoils

Mild steel (AISI 1018) was selected as model cold rolling material and Ti-6A1-4V and Inconel 718 were selected as typical hot rolling and cold rolling alloys, respectively. The flow stress and workability of these alloys were characterized and friction factor at the roll/workpiece interface was determined at their respective working conditions by conducting ring tests. Computer-aided mathematical models for predicting metal flow and stresses, and for simulating the shape rolling process were developed. These models utilized the upper bound and the slab methods of analysis, and were capable of predicting the lateral spread, roll separating force, roll torque, and local stresses, strains and strain rates. This computer-aided design system was also capable of simulating the actual rolling process, and thereby designing the roll pass schedule in rolling of an airfoil or a similar shape.

Lahoti, G. D.↗
NASA NTRS2004

A Comparison of Weld-Repaired and Base Metal for Inconel 718 and CRES 321 at Cryogenic and Room Temperatures

Fatigue crack growth tests were conducted to characterize the performance of Inconel 718 and CRES 321 welds, weld heat-affect-zone and parent metal at room temperature laboratory air and liquid nitrogen (-196oC) environments. The results of this study were required to predict the damage tolerance behavior of proposed orbiter main engine hydrogen fuel liner weld repairs. Experimental results show that the room and cryogenic temperature fatigue crack growth characteristics of both alloys are not significantly degraded by the weld repair process. However, both Inconel 718 and CRES 321 exhibited lower apparent toughness within the weld repair region compared to the parent metal.

Newman, John A.↗
NASA NTRSDate not supplied

A Comparison of Microstructure and Mechanical Performance of Inconel 718 Manufactured via L-PBF, LP-DED, and WAAM Technologies

The microstructure and mechanical properties of additively manufactured (AM) alloys can be significantly affected by variations in cooling rates, resulting from different process conditions across different additive manufacturing (AM) platforms. Therefore, it is crucial to understand the effect of manufacturing process on the microstructure and mechanical properties of AM Inconel 718. This study examines three AM processes: laser powder bed fusion, laser powder directed energy deposition, and wire arc additive manufacturing. Results show that fully heat treated laser powder bed fused (L-PBF) and wire arc additively manufactured (WAAM) Inconel 718 specimens exhibit higher strength compared to laser powder directed energy deposited (LP-DED) ones due to finer grain structure in L-PBF and retained dendritic microstructure in WAAM. The ductility in LP-DED Inconel 718 was slightly higher compared to WAAM and L-PBF due to relatively small carbide size, which causes stress concentration in a small material volume, leading to delayed fracture.

Additive manufacturing (AM)↗
NASA NTRS1982

Evaluation of dopants in hydrogen to reduce hydrogen permeation in candidate Stirling engine heater head tube alloys at 760 deg and 820 deg

Alloy tubes filled with hydrogen doped with various amounts of carbon monoxide, carbon dioxide, ethane, ethylene, methane, ammonia, or water were heated in a diesel fuel-fired Stirling engine simulator materials test rig for 100 hours at 21 MPa and 760 or 820 C to determine the effectiveness of the dopants in reducing hydrogen permeation through the hot tube walls. Ultra high purity (UHP) hydrogen was used for comparison. The tube alloys were N-155, A-286, Incoloy 800, Nitronic 40, 19-9DL, 316 stainless steel, Inconel 718, and HS-188. Carbon dioxide and carbon monoxide in the concentration range 0.2 to 5 vol % were most effective in reducing hydrogen permeation through the hot tube walls for all alloys. Ethane, ethylene, methane, ammonia, and water at the concentrations investigated were not effective in reducing the permeation below that achieved with UHP hydrogen. One series of tests were conducted with UHP hydrogen in carburized tubes. Carburization of the tubes prior to exposure reduced permeation to values similar to those for carbon monoxide; however, carbon dioxide was the most effective dopant.

Misencik, J. A.↗
DOE OSTI2025

Creep Property of Intermetallic Dispersive Steels for Nuclear Applications

To meet the materials performance demands of next-generation nuclear and high-temperature energy systems, a new class of intermetallic-dispersive steels (IDS) has been designed through integrated computational thermodynamics and alloy design strategies. The IDS alloys incorporate coherent L1₂ (γ′-Ni₃Al) nanoprecipitates within an Fe–Ni–Cr austenitic matrix, engineered to achieve both high temperature strength and thermodynamic stability while suppressing the formation of detrimental δ-Ni₃Nb and η-Ni₃Ti phases. Initial creep testing of Ti-IDS and TiTa-IDS alloys demonstrates rupture lives comparable to or exceeding those of Inconel 718 and ODS steels, despite being fabricated through conventional ingot metallurgy. Step-load creep tests identified a stress threshold near 300–350 MPa for the onset of tertiary creep, and in-situ neutron diffraction experiments on Ti-IDS revealed clear load partitioning between the matrix and γ′ precipitates: elastic strain is shared by both phases, while plastic strain localizes in the matrix. These results confirm that stable γ′–matrix interfaces play a dominant role in retarding dislocation motion and enhancing creep resistance. In FY26, the program will conduct repeat creep rupture testing of TiTa-IDS at 650 °C/400 MPa, initiate long-term rupture testing of TiNb-IDS, and perform TEM-based microstructural characterization to elucidate dislocation–precipitate interactions and microstructural stability. Collectively, these efforts will establish the mechanistic foundation for next-generation high-temperature structural materials based on the IDS concept.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1977

Effect of high-pressure oxygen on the mechanical properties of alloys

Unnotched and notched tensile properties of stressed and unstressed specimens of wrought 316 stainless steel, Incology 903, Monel K-500, and cast specimens of Inconel 718 were examined. Environmental tests were performed in atmospheric pressure air, high pressure nitrogen, and high pressure oxygen. Results show that oxygen did not alter the tensile properties of any of the alloys studied.

Schwartzberg, F. R.↗
NASA NTRS1968

Method for removing surface-damaged layers from nickel alloys

Electrical discharge machining /EDM/ damaged layer can be effectively removed from Rene 41, Inconel 625, Inconel 718, and Monel K-500 by abrasive-grit blasting or electropolishing /at room temperature/ at a current density of 5A/inches squared in a water solution of phosphoric and sulfuric acids.

Fawley, R. W.↗
NASA NTRS1978

Computer-aided analysis and design of the shape rolling process for producing turbine engine airfoils

Mild steel (AISI 1018) was selected as model cold-rolling material and Ti-6Al-4V and INCONEL 718 were selected as typical hot-rolling and cold-rolling alloys, respectively. The flow stress and workability of these alloys were characterized and friction factor at the roll/workpiece interface was determined at their respective working conditions by conducting ring tests. Computer-aided mathematical models for predicting metal flow and stresses, and for simulating the shape-rolling process were developed. These models utilize the upper-bound and the slab methods of analysis, and are capable of predicting the lateral spread, roll-separating force, roll torque and local stresses, strains and strain rates. This computer-aided design (CAD) system is also capable of simulating the actual rolling process and thereby designing roll-pass schedule in rolling of an airfoil or similar shape. The predictions from the CAD system were verified with respect to cold rolling of mild steel plates. The system is being applied to cold and hot isothermal rolling of an airfoil shape, and will be verified with respect to laboratory experiments under controlled conditions.

Lahoti, G. D.↗
NASA NTRS1984

Study of high performance alloy electroforming

The first series of heat treated nickel manganese alloys are tested for mechanical properties at temperatures of 148.9 C (300 F) and 260 C (500 F). All material receives the same heat treatment in order to provide a common basis for comparison of results. Mechanical property performance improves with increasing manganese content in the alloy. Although all manganese bearing alloy is significantly superior to conventional electroformed nickel, samples containing over 3000 ppm manganese display outstanding ultimate and yield strengths while maintaining reasonably satisfactory ductility. Alloy containing over 6000 ppm of manganese is very competitive to Inconel 718 (mill annealed and age hardened) at all temperatures of interest, although ductility is not as great in the electrodeposited counterpart.

Malone, G. A.↗
DOE OSTI2024

Microstructure and Mechanical Properties of Ni-based Alloys Fabricated by Laser Powder Bed Fusion

The Advanced Materials and Manufacturing Technologies (AMMT) program is aiming at the accelerated incorporation of new materials and manufacturing technologies into nuclear-related systems. Complex Ni-based components fabricated by laser powder bed fusion (LPBF) could enable operating temperatures at T > 700°C in aggressive environments such as molten salts or liquid metals. However, available mechanical properties data relevant to material qualification remains limited, in particular for Ni-based alloys routinely fabricated by LPBF such as IN718 (Ni- 19Cr-18Fe-5Nb-3Mo) and Haynes 282 (Ni-20Cr-10Co-8.5Mo-2.1Ti-1.5Al). Creep testing was conducted on LPBF 718 at 600°C and 650°C and on LPBF 282 at 750°C. finding that the creep strength of the two alloys was close to that of wrought counterparts. with lower ductility at rupture. Heat treatments were tailored to the LPBF-specific microstructure to achieve grain recrystallization and form strengthening γ' precipitates for LPBF 282 and γ' and γ" precipitates for LPBF 718. In-situ data generated during printing and ex-situ X-ray computed tomography (XCT) scans were used to correlate the creep properties of LPBF 282 to the material flaw distribution. In- situ data revealed that spatter particles are the potential causes for flaws formation in LPBF 282. with significant variation between rods based on their location on the build plate. XCT scans revealed the formation of a larger number of creep flaws after testing in the specimens with a higher initial flaw density. which led to a lower ductility for the specimen.

Dryepondt, Sebastien↗
NASA NTRS2003

Behavior of Three Metallic Alloys under Combined Axial-Shear Stresses at Elevated Temperature

Type 316 stainless steel, Haynes 188, and Inconel 718 samples were subjected to an axial-shear strain controlled loading history while the specimen temperature was held at 650 C to quantify the evolution of material state under a complex biaxial load path when the material is in the viscoplastic domain. Yield surfaces were constructed in the axial-shear stress plane using a sensitive, 30 x 10(exp -6)m/m, equivalent offset strain definition for the yield strain. Subsequent yield surfaces were constructed at various points along the strain path to define the material evolution. These subsequent yield surface translated, expanded, and distorted relative to the initial yield surface. Each of these very different materials exhibited components of isotropic, kinematic and distortional hardening. Furthermore, subsequent yield surfaces for each material have a very well defined front face and a poorly defined, flattened, back side.

Colaiuta, J. F.↗
NASA NTRS1981

Effect of oxide films on hydrogen permeability of candidate Stirling engine heater head tube alloys

The effect of oxide films developed in situ from CO/CO2 doped hydrogen on high pressure hydrogen permeability at 820 C was studied on N-155, A-286, IN 800, 19-9DL, Nitronic 40, HS-188, and IN 718 tubing in a Stirling materials simulator. The hydrogen permeability decreased with increasing dopant levels of CO or CO2 and corresponding decreases in oxide porosity. Minor reactive alloying elements strongly influenced permeability. At high levels of CO or CO2, a liquid oxide formed on alloys with greater than 50 percent Fe. This caused increased permeability. The oxides formed on the inside tube walls were analyzed and their effective permeabilities were calculated.

Schuon, S. R.↗
NASA NTRS1969

Hot-cracking studies of Inconel 718 weld- heat-affected zones

Hot ductility tests, gas-tungsten-arc fillerless fusion tests, and circle patch-weld-restraint tests were conducted on Inconel 718 to better understand and correlate the weldability /resistance to hot cracking/ of the alloy. A correlation of the test results with composition, heat-treat condition, grain size, and microstructure was made.

Thompson, E. G.↗