Search NASA⌕ Search

SEARCH · Search NASA

Results for “Auger electron spectroscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Deposition of reactively ion beam sputtered silicon nitride coatings

An ion beam source was used to deposit silicon nitride films by reactively sputtering a silicon target with beams of Ar + N2 mixtures. The nitrogen fraction in the sputtering gas was 0.05 to 0.80 at a total pressure of 6 to 2 millionth torr. The ion beam current was 50 mA at 500 V. The composition of the deposited films was investigated by auger electron spectroscopy and the rate of deposition was determined by interferometry. A relatively low rate of deposition of about 2 nm. one-tenth min. was found. AES spectra of films obtained with nitrogen fractions higher than 0.50 were consistent with a silicon to nitrogen ratio corresponding to Si3N4. However the AES spectra also indicated that the sputtered silicon nitride films were contaminated with oxygen and carbon and contained significant amounts of iron, nickel, and chromium, most probably sputtered from the holder of the substrate and target.

Grill, A.↗
NASA NTRS1981

Micro-area Auger analysis of a SiC/Ti fibre composite

Micro-area Auger electron spectroscopy with a spatial resolution of less than 50 nm has been used to study the concentration of elements across the reaction zone of a W-reinforced SiC fiber in a titanium matrix. Although the elemental concentrations obtained by this technique are affected by the reaction zone morphology to a greater extent than in the case of X-ray microprobe analysis, the proposed technique has the advantage of a much higher spatial resolution and avoids the problems of bulk averaging that characterize the X-ray technique.

Zironi, E. P.↗
NASA NTRS1982

UHV studies of the interaction of CO with small supported metal particles, Ni/mica

The interaction of carbon monoxide with small nickel (Ni) particles supported on UHV-cleaved mica was studied using flash thermal desorption, Auger electron spectroscopy, and transmission electron microscopy. Molecular desorption was accompanied by decomposition of CO at a rate strongly dependent on particle size. Recombination of surface-precipitated carbon with adsorbed oxygen was observed, and gas-induced morphological particle changes because of exposure to CO and O2 are analyzed in some detail.

Doering, D. L.↗
NASA NTRS1982

UHV studies of the interaction of CO with small supported metal particles, Pd/mica

The interaction of carbon monoxide with small palladium particles supported on UHV-cleaved and heat-treated single-crystal mica was studied. The Pd particles were characterized and tested using the techniques of flash thermal desorption, Auger electron spectroscopy, core electron energy loss spectroscopy, and transmission electron microscopy. Evidence is presented for CO decomposition on Pd particles during CO adsorption-desorption experiments. The rate of CO decomposition increased rapidly with diminishing particle size. Residual carbon from CO decomposition blocked CO adsorption and had a strong poisoning effect on the CO oxidation reaction.

Doering, D. L.↗
NASA NTRS1982

Chemisorption of CO on particulate deposits of platinum

Morphology and CO chemisorption properties are studied as a function of particle size for the case of particulate Pt films, vapor-deposited onto ultrahigh vacuum-cleaved and heat-treated mica surfaces at a 200 C substrate temperature. The particles were found to be mostly irregular in shape and randomly-oriented, with two desorption peaks after CO absorption at 60 C: (1) an alpha peak, at 120 C, attributed to smooth particle surfaces, and (2) a beta peak, at about 175 C, attributed to particle edges and steps. Transmission electron microscopy showed that major changes occur in particle morphology during absorption-desorption cycling, so that the decrease in CO desorption flux may be interpreted as due to particle restructuring, rather than contamination by CO decomposition as in the cases of Ni or Pd on mica. Auger electron spectroscopy corroborates the lack of CO decomposition, even for the case of very small Pt particles.

Doering, D. L.↗
NASA NTRS1982

Mechanisms of devitrification of grain boundary glassy phases in Si3N4 materials

Changes in the grain boundary (g.b.) phases of Si3N4 are analyzed, the effects of composition and thermal history on devitrification of the g.b. phases are determined, devitrification of the g.b. phases of Si3N are related to mechanical behavior and oxidation sensitivity of the material. The phase relationships that occur within the grain boundaries of Si3N4 containing various densification aids are reviewed. Comparisons of the effects of MgO, Y2O3, CeO2, and Y2O3 + AL2O3 are made in terms of the phase equilibria of the Si3N4 + SiO2 + additive compositional system. Two new equilibrium phase diagrams for the Si3N4-SiO2 and Y2O3 and Si3N4-SiO2-Ce2O3 systems are preented. The effects of Y2O3 vs CeO2 densification aids on the fracture surfaces of Si3N4 are compared. Auger electron spectroscopy shows that both oxides are concentrated within the fracture surface. Scanning electron microscopy shows evidence that Si3N4 with CeO2 formed an intergranular structure of fine grained oxynitride reaction products, as predicted by phase quilibria, whereas the Y2O3 containing sample shows evidence of an intergranular glassy phase.

Hench, L. L.↗
NASA NTRS1983

Mechanical and spectroscopic properties of metal-containing polyimides

The incorporation of specific metal ions into polyimides is described. Detailed studies have included various compounds of copper, lithium, and palladium as dopants. Addition of the metal during polymerization or after formation of the polyamic acid precedes the thermal imidization step. With many dianhydride-diamine-dopant combinations high quality variously colored films are produced. Many metal doped films exhibit (1) improved high temperature adhesive properties, (2) increased electrical conductivity, (3) excellent thermal stability, (4) improved acid/base resistance, (5) increased modulus in flexible films and (6) excellent high temperature tensile strength. X-ray photo-electron spectroscopic study of these films suggests that many of the additives undergo chemical modification during thermal imidization. Palladium dopants appear to be partially reduced to the metallic state, while lithium and copper dopants are probably converted to their oxides. Ion etching experiments with Auger electron spectroscopy monitoring are discussed.

Taylor, L. T.↗
NASA NTRS1982

Surface chemistry, friction and wear of Ni-Zn and Mn-Zn ferrites in contact with metals

X-ray photoelectron and Auger electron spectroscopy analysis were used in sliding friction experiments. These experiments were conducted with hot-pressed polycrystalline Ni-Zn and Mn-Zn ferrites, and single-crystal Mn-Zn ferrite in contact with various transition metals at room temperature in both vacuum and argon. The results indicate that Ni2O3 and Fe3O4 were present on the Ni-Zn ferrite surface in addition to the nominal bulk constituents, while MnO2 and Fe3O4 were present on the Mn-Zn ferrite surface in addition to the nominal bulk constituents. The coefficients of friction for the ferrites in contact with metals were related to the relative chemical activity of these metals. The more active the metal, the higher is the coefficient of friction. The coefficients of friction for the ferrites were correlated with the free energy of formation of the lowest metal oxide. The interfacial bond can be regarded as a chemical bond between the metal atoms and the oxygen anions in the ferrite surfaces. The adsorption of oxygen on clean metal and ferrite does strengthen the metal-ferrite contact and increase the friction. The ferrites exhibit local cracking and fracture with sliding under adhesive conditions. All the metals transferred to he surfaces of the ferrites in sliding.

Miyoshi, K.↗
NASA NTRS1983

Effect of oxygen concentration in ZDP containing oils on surface composition and wear

A pin-on-disk wear study was performed with the lubricants dibutyl sebacate (DBS) and mineral oil (MO) with and without 1 weight percent zinc-dialkyl-dithiophospatee (ZDP) as an additive. The pin was annealed pure iron and the disk was M-2 tool steel. The selected load and speed guaranteed boundary lubrication. The ambient atmospheric oxygen concentration in an oxygen-nitrogen mixture was varied from 0 percent to 20 percent in order to examine its relationship to ZDP effectiveness. Auger electron spectroscopy combined with argon ion bombardment (depth profiling) was used to determine surface elemental composition on the pin when tested in DBS with and without ZDP. The ambient atmosphere was found to cause large variations in wear rate and surface composition. With MO, ZDP reduced wear under all conditions, but had little advantage over oxides formed at 20 percent oxygen atmosphere. With DBS, ZDP reduced wear at 0 percent oxygen, but gave varied results at other oxygen concentrations. Depth profiling revealed sulfuide formation at 0 percent oxygen and probably sulfates at 20 percent oxygen. The results are significant because varied oxygen concentrations can occur under actual lubricating conditions in practical machinery.

Brainard, W. A.↗
NASA NTRS1983

Nitriding of titanium and titanium: 8 percent aluminum, 1 percent molybdenum, 1 percent vanadium alloy with an ion-beam source

Titanium and Ti-8Al-1Mo-1V alloy were nitrided with an ion-beam source of nitrogen or argon and nitrogen at a total pressure of 2 x 10 to the minus 4th power to 10 x 10 to the minus 4th power torr. The treated surface was characterized by surface profilometry, X-ray diffractometry, Auger electron spectroscopy and microhardness measurements. The tetragonal Ti2N phase formed in pure titanium and Ti-8Al-1Mo-1V alloy with traces of AlN in the alloy. Two opposite processes competed during the ion-beam-nitriding process: (1) formation of nitrides in the surface layer and (2) sputtering of the nitrided layers by the ion beam. The highest surface hardnesses, about 500 kg/sq mm in titanium and 800 kg/sq mm in Ti-8Al-1Mo-1V, were obtained by ion nitriding with an ion beam of pure nitrogen at 4.2 x 10 to the minus 4th power torr at a beam voltage of 1000 V.

Gill, A.↗
NASA NTRS1982

RF sputtered silicon and hafnium nitrides: Properties and adhesion to 440C stainless steel

Silicon nitride and hafnium nitride coatings were deposited by reactive RF sputtering on oxidized and unoxidized 440C stainless steel substrates. Sputtering was done in mixtures of argon and nitrogen gases from pressed powder silicon nitride and from hafnium metal targets. Depositions were at two background pressures, 8 and 20 mtorr, and at two different fractions (f) of nitrogen in argon, 0.25 and 0.60, for hafnium nitride and at f = 0.25 for silicon nitride. The coatings and the interface between the coating and substrates were investigated by X-ray diffractometry, scanning electron microscopy, energy dispersive X-ray analysis and Auger electron spectroscopy. A Knoop microhardness of 1650 + or - 100 kg/sq mm was measured for hafnium nitride and 3900 + or - 500 kg/sq mm for silicon nitride. The friction coefficients between a 440C rider and the coatings were measured under lubricated conditions. Scratch test results demonstrate that the adhesion of hafnium nitride to both oxidized and unoxidized 440C is superior to that of silicon nitride. Oxidized 440C is found to have increased adhesion, to both nitrides, over that of unoxidized 440C.

Grill, A.↗
NASA NTRS1982

XPS, AES and friction studies of single-crystal silicon carbide

The surface chemistry and friction behavior of a single crystal silicon carbide surface parallel to the 0001 plane in sliding contact with iron at various temperatures to 1500 C in a vacuum of 3 x 10 nPa are investigated using X-ray photoelectron and Auger electron spectroscopy. Results show that graphite and carbide-type carbon are seen primarily on the silicon carbide surface in addition to silicon at temperatures to 800 C by both types of spectroscopy. The coefficients of friction for iron sliding against a silicon carbide surface parallel to the 0001 plane surface are found to be high at temperatures up to 800 C, with the silicon and carbide-type carbon at maximum intensity in the X-ray photoelectron spectroscopy at 800 C. The concentration of the graphite increases rapidly on the surface as the temperature is increased above 800 C, while the concentrations of the carbide-type carbon and silicon decrease rapidly and this presence of graphite is accompanied by a significant decrease in friction. Preheating the surfaces to 1500 C also gives dramatically lower coefficients of friction when reheating in the sliding temperature range of from room temperature to 1200 C, with this reduction in friction due to the graphite layer on the silicon carbide surface.

Miyoshi, K.↗
NASA NTRS1983

Drastic reduction of adsorption of CO and H2 on (111)-type Pd layers

Clean surfaces of (111)-type Pd layers, grown from the vapor phase on Mo(110) at room temperature, were used to study the adsorption of CO and H2 by temperature-programmed desorption, Auger electron spectroscopy, and low-energy electron diffraction. Mild annealing of the as-grown layers during a single desorption cycle (to about 600 K) drastically reduces the adsorption for both adsorbates. Low-dose argon-ion bombardment introduces surface imperfections which restore a high adsorption probability. The results are interpreted in terms of particular (111)-type surface structures that persist tp layer thicknesses of about four monolayers; the results raise questions with respect to the surface structure of supported thin epitaxial islands and particles of Pd and possibly also with respect to conventional methods of preparing bulk surfaces of Pd for adsorption studies.

Poppa, H.↗
NASA NTRS1983

Tribological characteristics of nitrogen (N+) implanted iron

The effect of implantation of nitrogen ions (1.5 MeV) on the friction and wear characteristics of pure ion sliding against M-50 steel (unimplanted) was studied in a pin-on-disk sliding friction apparatus. Test conditions included room temperature (25 C), a dry air atmosphere, a load of 1/2 kg (4.9 N), sliding velocities of 0.043 to 0.078 m/sec (15 to 25 rpm), a pure hydrocarbon lubricant (n-hexadecane), or a U.S.P. mineral oil and nitrogen ion implantation doses of 5x10 to the 15th power and 5x10 to the 17th power ions/sq cm. No differences in wear rates were observed in the low dose experiments. In the high dose experiments, small reductions in initial (40 percent) and steady state (20 percent) wear rates were observed for nitrogen implanted iron riders as compared with unimplanted controls. No differences in average friction coefficients were noted for either dose. Auger electron spectroscopy combined with argon ion bombardment revealed a subsurface Gaussian nitrogen distribution with a maximum concentration of 6 atomic percent at a depth of 0.8 microns. Similar analysis within the wear scar of an implanted rider after 20 microns of wear yielded only background nitrogen concentration. No inward migration of nitrogen ions was observed. Previously announced in STAR as N82-24322

Jones, W. R., Jr.↗
NASA NTRS1983

Interfacial chemistry of electrical contacts on GaAs and Al0.3Ga0.7As

Thermal restructuring of oxides of GaAs and Al0.3Ga0.7As substrates has been studied using Auger electron spectroscopy and both neutral and secondary ion mass spectrometry. The oxide underwent restructuring at temperature of at least 250 C while gallium oxides desorbed at temperatures depending upon the type of oxide. Reoxidation at low oxygen pressures resulted in surface oxygen species different from those in native oxides. These species desorbed at about 520 C while native oxides desorbed at 600 C. Carbon-containing contaminants did not desorb. The implications of these results for electrical contacts are discussed.

Buonaquisti, A. D.↗
NASA NTRS1983

Interfacial layers in high-temperature-oxidized NiCrAl

The utility of Auger electron spectroscopy combined with ball cratering for depth analysis of oxide and diffusion layers produced in a Ni-14Cr-24Al alloy by oxidation in air at 1180 C for 25 hr is demonstrated. During postoxidation cooling, the oxide layers formed by this alloy spalled profusely. The remaining very thin oxide was primarily Cr2O3 with a trace of Ni. The underlying metal substrate exhibited gamma/gamma-prime and beta phases with a metallic interfacial layer which was similar to the bulk gamma/gamma-prime phase but slightly enriched in Cr and Al. These data are compared to electron microprobe results from a nominally identical alloy. The diffusion layer thickness is modelled with a simple mass balance equation and compared to recent results on the diffusion process in NiCrAl alloys.

Larson, L. A.↗
NASA NTRS1983

Surface acoustic wave/silicon monolithic sensor/processor

A new technique for sputter deposition of piezoelectric zinc oxide (ZnO) is described. An argon-ion milling system was converted to sputter zinc oxide films in an oxygen atmosphere using a pure zinc oxide target. Piezoelectric films were grown on silicon dioxide and silicon dioxide overlayed with gold. The sputtered films were evaluated using surface acoustic wave measurements, X-ray diffraction, scanning electron microscopy, Auger electron spectroscopy, and resistivity measurements. The effect of the sputtering conditions on the film quality and the result of post-deposition annealing are discussed. The application of these films to the generation of surface acoustic waves is also discussed.

Kowel, S. T.↗
NASA NTRS1983

Radiative properties of advanced spacecraft heat shield materials

Experimental results are presented to show the effects of simulated reentry exposure by convective heating and by radiant heating on spectral and total emittance of statically oxidized Inconel 617 and Haynes HS188 superalloys to 1260 K and a silicide coatea (R512E) columbium 752 alloy to 1590 K. Convective heating exposures were conducted in a supersonic arc plasma wind tunnel using a wedge-shaped specimen configuration. Radiant tests were conducted at a pressure of .003 atmospheres of dry air at a flow velocity of several meters per second. Convective heating specimens were subjected to 8, 20, and 38 15-min heating cycles, and radiant heating specimens were tested for 10, 20, 50, and 100 30-min heating cycles. Changes in radiative properties are explained in terms of changes in composition resulting from simulated reentry tests. The methods used to evaluate morphological, compositional and crystallographic changes include: Auger electron spectroscopy; scanning electron microscopy; X-ray diffraction analysis; and electron microprobe analysis.

Cunnington, G. R.↗