Experimental evaluation of outer case blowing or bleeding of single stage axial flow compressor. Part 4 - Performance of bleed insert configuration no. 3
Evaluation of bleed insert configuration of single stage axial flow compressor
Koch, C. C.↗
SEARCH · Search NASA
Results for “Axial Compressors”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Comparison between optical measurements and a numerical solution of the flow field within a transonic axial-flow compressor rotor
A comparison between numerical and experimental results is presented for the flowfield within a transonic axial-flow compressor rotor. The rotor was tested at design speed and a wide open throttle discharge condition. The relative tip Mach number was 1.4. A laser anemometer system was used to measure velocity and flow angle upstream, within, and downstream of the rotor. A holographic interferometer was used to visualize the rotor shock system near the tip. The computational procedure solves the full three-dimensional Euler equations using a time-marching technique. Shock location and shape determined from the two optical systems are compared. Calculated relative Mach number and flow angle contours, shock locations, and shock strength are compared to values measured with the laser anemometer.
Strazisar, A. J.↗
Predicting the Performance of an Axial-Flow Compressor
Stage-stacking computer code (STGSTK) developed for predicting off-design performance of multi-stage axial-flow compressors. Code uses meanline stagestacking method. Stage and cumulative compressor performance calculated from representative meanline velocity diagrams located at rotor inlet and outlet meanline radii. Numerous options available within code. Code developed so user modify correlations to suit their needs.
Steinke, R. J.↗
Investigation of an Experimental Supersonic Axial-Flow Compressor
An investigation is in progress at the Langley Laboratory of the NACA to explore the possibilities of axial-flow compressors operating with supersonic velocities relative to the blade rows. The first phase of this investigation, a study of supersonic diffusers, has been reported. The second phase, an analysis of supersonic compressors, has also been reported. Preliminary calculations have shown that very high pressure ratios across a stage, together with somewhat increased mass flows, are possible with compressors which decelerate air through the speed of sound in their rotor blading. These performance characteristics are desirable in compressors for aircraft jet propulsion units, gas turbines, or superchargers. The third phase, presented here, is a preliminary experimental investigation of a supersonic compressor designed to produce a high pressure ratio in a single stage.
Erwin, John R.↗
Axial flow compressor computer program for calculating off design performance /Program 4/
Computer program for calculating off-design aerodynamic performance of axial flow compressor
Carmody, R. H.↗
Experimental evaluation of outer case blowing or bleeding of single stage axial flow compressor. Part 3 - Performance of blowing insert configuration no. 1
Experimental evaluation of outer case blowing or bleeding of single stage axial flow compressor, and performance tests using distorted or undistorted inlet flow
Koch, C. C.↗
Analysis of supersonic stall bending flutter in axial-flow compressor by actuator disk theory
An analytical model was developed for predicting the onset of supersonic stall bending flutter in axial-flow compressors. The analysis is based on two-dimensional, compressible, unsteady actuator disk theory. It is applied to a rotor blade row by considering a cascade of airfoils. The effects of shock waves and flow separation are included in the model. Calculations show that the model predicts the onset, in an unshrouded rotor, of a bending flutter mode that exhibits many of the characteristics of supersonic stall bending flutter. The validity of the analysis for predicting this flutter mode is demonstrated.
Adamczyk, J. J.↗
Mean velocity and decay characteristics of the guidevane and stator blade wake of an axial flow compressor
Pure tone noise, blade row vibrations, and aerodynamic losses are phenomena which are influenced by stator and IGV (inlet guide vane) blade wake production, decay, and interaction in an axial-flow compressor. The objective of this investigation is to develop a better understanding of the nature of stator and IGV blade wakes that are influenced by the presence of centrifugal forces due to flow curvature. A single sensor hot wire probe was employed to determine the three mean velocity components of stator and IGV wakes of a single stage compressor. These wake profiles indicated a varying decay rate of the tangential and axial wake velocity components and a wake profile similarity. An analysis, which predicts this trend, has been developed. The radial velocities are found to be appreciable in both IGV and the stator wakes.
Lakshminarayana, B.↗
STGSTK: A computer code for predicting multistage axial flow compressor performance by a meanline stage stacking method
A FORTRAN computer code is presented for off-design performance prediction of axial-flow compressors. Stage and compressor performance is obtained by a stage-stacking method that uses representative velocity diagrams at rotor inlet and outlet meanline radii. The code has options for: (1) direct user input or calculation of nondimensional stage characteristics; (2) adjustment of stage characteristics for off-design speed and blade setting angle; (3) adjustment of rotor deviation angle for off-design conditions; and (4) SI or U.S. customary units. Correlations from experimental data are used to model real flow conditions. Calculations are compared with experimental data.
Steinke, R. J.↗
Vibration Survey of Blades in 19XB Axial-Flow Compressor: Dynamic Investigation - 2
Strain-gage measurements were taken under operating conditions from blades of various stages of the 19XB axial-flow compressor in an effort to determine the reason for failures in the seventh and tenth stages. First bending-mode vibrations were detected in the first five stages of the compressor caused by each integral multiple of rotor speed from three through ten. Lead-wire failures in the last five stages resulted in incomplete data. The dynamic-vibration frequencies at various rotor speeds were compared with statically measured frequencies analytically corrected for the influence of centrifugal force. Large increases in vibration ani~litude with increased pressure ratio were observed. During surging operation, blade vibrations were not present. The effects of pressure ratio and surge indicate the existence of aerodynamic excitation as the cause of the blade vibrations.
Meyer, Andre J., Jr.↗
Performance of a 1380-foot-per-second-tip-speed axial-flow compressor rotor with a blade tip solidity of 1.3
Aerodynamic design parameters are presented along the overall and blade element performance, of an axial flow compressor rotor designed to study the effects of blade solidity on efficiency and stall margin. At design speed the peak efficiency was 0.844 and occurred at an equivalent weight flow of 63.5 lb/sec with a total pressure ratio of 1.801. Design efficiency, pressure ratio, and weight flow 0.814, 1.65, and 65.3(41.1 lb/sec/sq ft of annulus area), respectively. Stall margin for design speed was 6.4 percent based on the weight flow and pressure ratio values at peak efficiency and just prior to stall.
Hager, R. D.↗
Performance of 1380 foot per second tip-speed axial-flow compressor rotor blade tip solidity of 1.5
This presents the aerodynamic design parameters along with the overall and blade element performance of an axial-flow compressor rotor designed to study the effects of blade solidity on efficiency and stall margin. At design speed the peak efficiency was 0.892 and occurred at an equivalent weight flow of 65.0 lb/sec. The total pressure ratio was 1.83 and the total temperature ratio was 1.215. Design efficiency, weight flow, pressure ratio, and temperature ratio were 0.824, 65.3, 1.65, and 1.187, respectively. Stall margin for design speed was 10 percent based on the weight flow and pressure ratio values at peak efficiency and just prior to stall.
Ball, C. L.↗
Experimental evaluation of outer case blowing or bleeding of single stage axial flow compressor. Part 5 - Performance of plain casing insert configuration with distorted inlet flow
Outer case bleeding or blowing effects on casing insert of single stage axial flow compressor with distorted inlet flow
Koch, C. C.↗
Performance of 1380-foot-per-second tip-speed axial-flow compressor rotor with blade tip solidity of 1.1
The aerodynamic design parameters are presented along with the overall and blade element performance, of an axial-flow compressor rotor designed to study the effects of blade solidity on efficiency and stall margin. At design speed the peak efficiency was 0.853 and occured at an equivalent weight flow of 65.7lb/sec. The total pressure ratio was 1.68. Design efficiency, weight flow, pressure ratio, and temperature ratio were 0.822, 65.3, 1.65, and 1.187, respectively. Stall margin for design speed was 14 percent based on the weight flows and pressure ratios at peak efficiency and just prior to stall.
Janetzke, D. C.↗
Frequency response of an axial-flow compressor exposed to inlet pressure perturbations
Experimental results of a series of engine tests designed to obtain the stage dynamics of an eight-stage axial-flow compressor over the frequency range of 0.5 to 200 hertz are presented. The total pressure at the compressor face was varied by means of a secondary air jet system installed in the engine inlet and positioned to oppose the primary airflow. Total-pressure probes located at each compressor stage were used to obtain the frequency response of each compressor-stage total pressure to the average compressor-inlet total pressure. The engine operating conditions were chosen to illustrate the effects of changing the rotor speed, changing the exhaust nozzle area, and isolating the compressor discharge pressure perturbations from the fuel control and hence, the fuel flow.
Milner, E. J.↗
End-wall and profile losses in a low-speed axial flow compressor rotor
The blade-to-blade variation of relative stagnation pressure losses in the tip region inside the rotor of a single-stage, axial-flow compressor, is presented and interpreted in this paper. The losses are measured at two flow coefficients (one at the design point and the other at the near peak pressure rise point) to discern the effect of blade loading on the end-wall losses. The tip clearance losses are found to increase with an increase in the pressure rise coefficient. The losses away from the tip region and near the hub regions are measured downstream. The losses are integrated and interpreted in this paper.
Lakshminarayana, B.↗
Investigation of Performance of Axial-Flow Compressor of XT-46 Turbine-Propeller Engine. I - Preliminary Investigation at 50-,70-, and 100-Percent Design Equivalent Speed
An investigation is being conducted to determine the performance of the 12-stage axial-flow compressor of the XT-46 turbine-propeller engine. This compressor was designed to produce a pressure ratio of 9 at an adiabatic efficiency of 0.86. The design pressure ratios per stage were considerably greater than any employed in current aircraft gas-turbine engines using this type of compressor. The compressor performance was evaluated at two stations. The station near the entrance section of the combustors indicated a peak pressure ratio of 6.3 at an adiabatic efficiency of 0.63 for a corrected weight flow of 23.1 pounds per second. The other, located one blade-chord downstream of the last stator row, indicated a peak pressure ratio of 6.97 at an adiabatic efficiency of 0.81 for a corrected weight flow of 30.4 pounds per second. The difference in performance obtained at the two stations is attributed to shock waves in the vicinity of the last stator row. These shock waves and the accompanying flow choking, together with interstage circulatory flows, shift the compressor operating curves into the region where surge would normally occur. The inability of the compressor to meet design pressure ratio is probably due to boundary-layer buildup in the last stages, which cause axial velocities greater than design values that, in turn, adversely affect the angles of attack and turning angles in these blade rows.
John W R Creagh↗
Investigation of X24C-2 10-Stage Axial-Flow Compressor: Effect of Inlet-Air Pressure and Temperature of Performance - 2
Effect of inlet-air pressure and temperature on the performance of the X24-2 10-Stage Axial-Flow Compressor from the X24C-2 turbojet engine was evaluated. Speeds of 80, 89, and 100 percent of equivalent design speed with inlet-air pressures of 6 and 12 inches of mercury absolute and inlet-air temperaures of approximately 538 degrees, 459 degrees,and 419 degrees R ( 79 degrees, 0 degrees, and minus 40 degrees F). Results were compared with prior investigations.
Finger, Harold B.↗