SEARCH · Search NASA

Results for “Brittle fracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Compliance calibration of the short rod chevron-notch specimen for fracture toughness testing of brittle materials

The short rod chevron-notch specimen has the advantages of (1) crack development at the chevron tip during the early stage of test loading, and (2) convenient calculation of plane-strain fracture toughness from the maximum test load and from a calibration factor which depends only on the specimen geometry and manner of loading. For generalized application, calibration of the specimen over a range of specimen proportions and chevron-notch configurations is necessary. Such was the objective of this investigation, wherein calibration of the short rod specimen was made by means of experimental compliance measurements converted into dimensionless stress intensity factor coefficients.

Bubsey, R. T.↗

DOE OSTI2020

The combined effects of hydrogen and aging condition on the deformation and fracture behavior of a precipitation-hardened nickel-base superalloy

The effect of hydrogen (H) on the deformation behavior of Monel K-500 in various isothermal heat treatment conditions (non-aged, under-aged, peak-aged, and over-aged) was assessed via uniaxial mechanical testing. H-charged and non-charged specimens were strained to failure to facilitate a comparison of ductility, fracture surface morphology, strength, and work hardening behavior. For all examined heat treatment conditions, H charging leads to a significant reduction in ductility, which is accompanied by a consistent change in fracture surface morphology from ductile microvoid coalescence to brittle intergranular fracture. While H charging led to a systematic enhancement in the yield strength of all heat treatments, the three age-hardened conditions exhibited a more than 2-fold increase relative to the non-aged heat treatment. This suggests that H modifies the dislocation–precipitate interactions, which also manifest themselves through changes in work hardening metrics related to the dislocation storage and recovery rates. In particular, the H-charged peak-aged specimen exhibited a significant increase in initial hardening (dislocation storage) rate relative to the H-charged under-aged specimen. Transmission electron microscopy of these samples revealed the onset of widespread dislocation looping in the H-charged peak-aged sample, in addition to the planar slip bands characteristic of the non-charged condition. This result suggests that hydrogen induces the particle shearing-to-looping transition at smaller particle sizes. Possible mechanistic explanations for this observed behavior are presented.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Numerical Simulation of Container Breach and Airborne Release of Solids Due to Mechanical Insults

Throughout U.S. Department of Energy (DOE) complexes, safety engineers employ the five-factor formula to calculate the source term (ST) that includes parameters of airborne release fraction (ARF), respirable fraction (RF) and damage ratio (DR). Limited experimental data on fragmentation of solids, such as ceramic pellets (i.e., PuO2), and container breach due to mechanical insults (i.e., drop and forklift impact), can be supplemented by modeling and simulation using high fidelity computational tools to estimate these parameters. This paper presents the use of Sandia National Laboratories' SIERRA solid mechanics (SM) finite element code to investigate the behavior of the widely utilized waste container (such as 7A Drum) subject to a range of free fall impact and puncture scenarios. The resulting behavior of the container is assessed, and the estimates are presented for bounding DRs from calculated breach areas for the various accident conditions considered. This paper also describes a novel multiscale constitutive model recently implemented in SIERRA/SM that simulates the fracture of brittle materials such as PuO 2 and determines ARF during the fracture process. Furthermore, comparisons are made between model predictions and simple bench-top experiments.

61 RADIATION PROTECTION AND DOSIMETRY↗

NASA NTRS1985

Influence of the resin on interlaminar mixed-mode fracture

Both literature review data and new data on toughness behavior of seven matrix and adhesive systems in four types of tests were studied in order to assess the influence of the resin on interlaminar fracture. Mixed mode (i.e., various combinations of opening mode 1, G sub 1, and shearing mode 2; G sub 2) fracture toughness data showed that the mixed mode relationship for failure appears to be linear in terms of G sub 1 and G sub 2. The study further indicates that fracture of brittle resins is controlled by the G sub 1 component, and that fracture of many tough resins is controlled by total strain-energy release rate, G sub T. Regarding the relation of polymer structure and the mixed mode fracture: high mode 1 toughness requires resin dilatation; dilatation is low in unmodified epoxies at room temperature/dry conditions; dilatation is higher in plasticized epoxies, heated epoxies, and in modified epoxies; modification improves mode 2 toughness only slightly compared with mode 1 improvements. Analytical aspects of the cracked lap shear test specimen were explored.

Johnson, W. S.↗

NASA NTRS1987

Influence of the resin on interlaminar mixed-mode fracture

Johnson, W. S.↗

NASA NTRS1986

References and conference proceedings towards the understanding of fracture mechanics

A list of books, reports, periodicals, and conference proceedings, as well as individual papers, centered on specific aspects of fracture phenomenon has been compiled by the ASTM Committee E-24 on Fracture Testing. A list of basic references includes the articles on the development of fracture toughness, evaluation of stress intensity factors, fatigue crack growth, fracture testing, fracture of brittle materials, and fractography. Special attention is given to the references on application of fracture mechanics to new designs and on reevaluation of failed designs, many of them concerned with naval and aircraft structures.

Toor, P. M.↗

DOE OSTI2020

Damage and Failure in a Statistical Crack Model

In this paper I will take a close look at a statistical crack model (SCM) as is used in engineering computer codes to simulate fracture at high strain rates. My general goal is to understand the macroscopic behavior effected by the microphysical processes incorporated into an SCM. More specifically, I will assess the importance of including local interactions between cracks into the growth laws of an SCM. My strategy will be to construct a numerical laboratory that represents a single computational cell containing a realization of a statistical distribution of cracks. The cracks will evolve by the microphysical models of the SCM, leading to quantifiable damage and failure of the computational cell. I will use the numerical data generated by randomly generated ensembles of the fracture process to establish scaling laws that will modify and simplify the implementation of the SCM into large scale engineering codes.

42 ENGINEERING↗

NASA NTRS1989

Reliability-based failure analysis of brittle materials

The reliability of brittle materials under a generalized state of stress is analyzed using the Batdorf model. The model is modified to include the reduction in shear due to the effect of the compressive stress on the microscopic crack faces. The combined effect of both surface and volume flaws is included. Due to the nature of fracture of brittle materials under compressive loading, the component is modeled as a series system in order to establish bounds on the probability of failure. A computer program was written to determine the probability of failure employing data from a finite element analysis. The analysis showed that for tensile loading a single crack will be the cause of total failure but under compressive loading a series of microscopic cracks must join together to form a dominant crack.

Powers, Lynn M.↗

NASA NTRS1975

Surface energy and surface tension at holes and cracks

The concept of surface tension and surface energy of solids was used by Griffith to obtain a criterion for the extension of cracks in brittle materials. Griffith, however, neglected the stresses due to the normal traction at the crack implied by the surface tension. A complete solution to the problem of an elliptic hole in an infinite plate with surface tension loading at the hole is given. Complex potentials are given in closed form in terms of elliptic integrals of the first, second, and third kinds. Stress distributions are studied. For a flat crack, the nature of the singularity at the tip is shown to be radically different from that usually encountered in fracture mechanics. The implications of our analysis for theories of fracture in brittle materials are discussed.

Rajapakse, Y. D. S.↗

DOE OSTI2026

Capturing the fractocohesive length scale in elastomers through a statistical mechanics-based gradient enhanced damage model

Here, this study aims to examine modeling flaw sensitivity in elastomers. The direct incorporation of polymer chain statistical mechanics considerations into a continuum stretch-based gradient-enhanced damage formulation, in turn, allows a representation of diffuse chain damage and fracture events that align with known micromechanical mechanisms. Through a series of numerical experiments, we simulate crack propagation and extract the fracture energy as an output of the model, while keeping track of the micromechanical signatures of diffuse chain damage that accommodate fracture propagation and eventually influence flaw sensitivity. Finally, by combining the fracture toughness and the work to rupture, we identify a fractocohesive length of the material, corresponding to the full width of the damage process zone. As the damage-to-fracture cascade in the proposed GED model is influenced by the introduction of a length scale associated with network imperfection and long-range load transfer, the emerging relationship of the two length scales is discussed, providing a potential link between microscopic damage mechanisms and the observed macroscopic fracture response.

36 MATERIALS SCIENCE↗

DOE OSTI2022

A unified finite strain gradient-enhanced micropolar continuum approach for modeling quasi-brittle failure of cohesive-frictional materials

Here, in this work, a novel framework for modeling quasi-brittle crack propagation and shear band dominated failure of cohesive-frictional materials like concrete, mortar, rock, tough ceramics, energetic materials, but also granular materials like sands or powders in terms of a unified continuum approach is proposed. It is based on a combination of the gradient-enhanced continuum with gradients of internal variables for representing quasi-brittle cracking, and the micropolar continuum, accounting for the deformation of the microstructure. For developing the gradient-enhanced micropolar framework, the set of balance equations and the kinematic relations are derived, and the constitutive relations are established in a general manner. The framework is formulated in a geometrically exact setting, based on the thermodynamically sound theory of hyperelasto-plasticity, and the numerical implementation by means of the finite element method is discussed. For assessing the approach, realizations of this new approach in terms of constitutive models for particular materials are developed. They are applied to numerical benchmark examples, investigating various loading conditions, and the obtained results are validated by means of a comparison with experiments from the literature.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Hydroxylpyromorphite, a mineral important to lead remediation: Modern description and characterization

Abstract Hydroxylpyromorphite, Pb5(PO4)3(OH), has been documented in the literature as a synthetic and naturally occurring phase for some time but has not previously been formally described as a mineral. It is fully described here for the first time using crystals collected underground in the Copps mine, Gogebic County, Michigan. Hydroxylpyromorphite occurs as aggregates of randomly oriented hexagonal prisms, primarily between about 20–35 μm in length and 6–10 μm in diameter. The mineral is colorless and translucent with vitreous luster and white streak. The Mohs hardness is ~3½–4; the tenacity is brittle, the fracture is irregular, and indistinct cleavage was observed on {001}. Electron microprobe analyses provided the empirical formula Pb4.97(PO4)3(OH0.69F0.33Cl0.06)Σ1.08. The calculated density using the measured composition is 7.32 g/cm3. Powder X-ray diffraction data for the type material is compared to data previously reported for hydroxylpyromorphite from the talc mine at Rabenwald, Austria, and from Whytes Cleuch, Wanlockhead, Scotland. Hydroxylpyromorphite is hexagonal, P63/m, at 100 K, a = 9.7872(14), c = 7.3070(10) Å, V = 606.16(19) Å3, and Z = 2. The structure [R1 = 0.0181 for 494 F>4σ(F) reflections] reveals that hydroxylpyromorphite adopts a column anion arrangement distinct from other members of the apatite supergroup due to the presence of fluorine and steric constraints imposed by stereoactive lone-pair electrons of Pb2+ cations. The F– anion sites are displaced slightly from hydroxyl oxygen anions, which allows for stronger hydrogen-bonding interactions that may in turn stabilize the observed column-anion arrangement and overall structure. Our modern characterization of hydroxylpyromorphite provides deeper understanding to a mineral useful for remediation of lead-contaminated water.

Geochemistry & Geophysics↗

DOE OSTI2020

Fracture Strength Determination Methods for Ceramic Materials Applied to Uranium Dioxide

The Advanced Fuels Campaign is currently focusing on development of accident-tolerant fuels that possess a range of property modifications intended to improve fuel performance during accident and transient conditions as well as extend license limits to burnups beyond 62 MWd/kgU. Both of these drivers have identified understanding and mitigating fuel cracking as a key performance criterion. Small-scale cantilever beam testing has been identified as a plausible method by which to collect fracture data for UO 2 as a function of chemical and structural evolutions introduced either during fabrication or irradiation. While this method has been found to be capable of providing data that are in reasonable agreement with literature for unirradiated UO 2 , the inherently small sample volumes that can be sampled limit its ability to capture the statistical nature of mechanisms that govern the fracture of brittle ceramics. A biaxial flexure strength test was developed to be used for unirradiated UO 2 . This method is standard in the community, but no systems presently in use at national laboratories, universities, or private companies are available to be used for nuclear fuel materials. This report describes the operation and benchmarking of this system, which has been validated for a number of common oxides. Future work will extend this system to characterization of both doped UO 2 and other relevant microstructural modifications that can also be measured using small-scale cantilever beam testing. Comparison of datasets collected using both methods will allow the overall applicability of small-scale techniques to be assessed and provide confidence or bounds on their use for irradiated fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Impact of annealing at 1000°C in flowing He with low O 2 concentration on the room temperature tensile properties of Mo alloys

NorthStar is developing an accelerator-based technology to produce the medical isotope Mo-99. A previous ORNL report (ORNL/SPR-2022/2490) studied the oxidation behavior of Mo in flowing He with low oxygen content at 800°C and 1000°C and it was shown that an O 2 concentration lower than ~5ppm (μ1/1) is required to achieve acceptable oxidation rates for wrought or powder metallurgy (PM) Mo. Oxidation may also impact the mechanical properties of Mo and this report summarizes tensile results at room temperature on wrought and PM Mo before and after exposure at 1000°C in flowing He with O 2 concentration varying from 1 to 15 ppm O 2 . It was found that oxidation at 1000°C results in a significant decrease of Mo strength and ductility with brittle intergranular fracture surfaces, likely due to the segregation of oxygen at grain boundaries. For the PM Mo material, the decrease in strength and ductility was also observed after annealing in vacuum at 1000°C, indicating that the diffusion of the oxygen trapped in the material pores to grain boundaries after 20-100h at 1000°C is sufficient to embrittle the material. Finally, initial results on actual aMo and high-density disks provided by NorthStar revealed the lack of ductility of the materials due to the specific disk microstructure.

36 MATERIALS SCIENCE↗

NASA NTRS1967

Delayed fracture of titanium alloys

Delayed fracture tests and brittle properties of titanium aluminum zirconium alloy

ALUMINUM ALLOY↗

NASA NTRS1979

Improved adherence of sputtered titanium carbide coatings on nickel- and titanium-base alloys

Rene 41 and Ti-6Al-4V alloys were radio frequency sputter coated with titanium carbide by several techniques in order to determine the most effective. Coatings were evaluated in pin-on-disk tests. Surface analysis by X-ray photoelectron spectroscopy was used to relate adherence to interfacial chemistry. For Rene 41, good coating adherence was obtained when a small amount of acetylene was added to the sputtering plasma. The acetylene carburized the alloy surface and resulted in better bonding to the TiC coating. For Ti-6Al-4V, the best adherence and wear protection was obtained when a pure titanium interlayer was used between the coating and the alloy. The interlayer is thought to prevent the formation of a brittle, fracture-prone, aluminum oxide layer.

Wheeler, D. R.↗

NASA NTRS1986

Dislocation mechanism based model for stage II fatigue crack propagation rate

Repeated plastic deformation, which of course depends on dislocation mechanism, at or near the crack tip leads to the fatigue crack propagation. By involving the theory of thermally activated flow and the cumulative plastic strain criterion, an effort is made here to model the stage II fatigue crack propagation rate in terms of the dislocation mechanism. The model, therefore, provides capability to ascertain: (1) the dislocation mechanism (and hence the near crack tip microstructures) assisting the crack growth, (2) the relative resistance of dislocation mechanisms to the crack growth, and (3) the fracture surface characteristics and its interpretation in terms of the dislocation mechanism. The local microstructure predicted for the room temperature crack growth in copper by this model is in good agreement with the experimental results taken from the literature. With regard to the relative stability of such dislocation mechanisms as the cross-slip and the dislocation intersection, the model suggests an enhancement of crack growth rate with an ease of cross-slip which in general promotes dislocation cell formation and is common in material which has high stacking fault energy (produces wavy slips). Cross-slip apparently enhances crack growth rate by promoting slip irreversibility and fracture surface brittleness to a greater degree.

Mazumdar, P. K.↗

NASA NTRS1988

Reliability based analysis of contact problems

The Batdorf model is modified to include the reduction in shear due to the effect of compressive stresses on the crack face. This new formulation was used to obtain the probability of failure of ceramic components under contact stress conditions. The combined effect of the surface and volume flaws are included in the analysis. Due to the nature of the fracture of brittle materials under compressive loading, the component is modeled as a series system in order to establish bounds on the probability of failure.

Powers, Lynn M.↗