Corrosion of Stainless and Carbon Steel in Aqueous Piperazine for CO2 Capture
PhD Dissertation
Liu, Ching-Ting↗
SEARCH · Search NASA
Results for “CO2 Capture”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Novel Algae Technology for CO2 Utilization
The United States, the world’s largest energy user and second largest CO2 emitter, is heavily dependent on fossil energy. In 2014, U.S. coal burning utilities emitted ~1562 million (MM) tons/year (TPY) of CO2 into the atmosphere, accounting for 76% of the total US power sector emissions1. Hence, reducing the CO2 emission footprint from coal plants is widely viewed as a key element in mitigating global warming. Despite significant interest, implementation of CO2 capture technologies has been constrained by the high capture cost which significantly increases the total cost of electricity. Not only is capturing CO2 with traditional technologies expensive, but generally the CO2 has little value and additional expense must be incurred for sequestration. This project funded by a SBIR grant from the U.S. D.O.E. to Helios-NRG in collaboration with the State University of New York at Buffalo (UB) and Membrane Technology and Research Inc. (MTR) aimed to develop a novel, algae based technology to capture CO2 from the effluent of coal-based power plants and convert it to renewable bio-fuels and higher value co-products such as animal feed and nutraceuticals with the potential to enable a substantial reduction in the net cost of carbon capture. The Phase 2 project was aimed at further demonstrating the technical feasibility of the proposed multi-stage continuous (MSC) flow CO2 capture system and the generation of high-value co-products to offset the CO2 capture cost. The project was completed and the project objectives were met and exceeded. A first-of-a-kind integrated, laboratory scale MSC process unit was fabricated and tested in a greenhouse. The tests were conducted with the preferred algae species identified in Phase I and simulated flue gas containing contaminants at levels typically present in the post flue gas desulfurization (FGD) stream, including ~12% CO2, acid gas (SOX, NOX), and a large number of heavy metals. The tests were successful and demonstrated a 25g/m2/day seasonal average algae productivity and an 80% CO2 capture efficiency. Two new algae species were identified for high-value nutraceutical production. Studies to improve growth rate and nutraceutical content of these algae species were performed and a pathway for further improvements was identified. A new dewatering technology called DeAqua was further advanced. Significant improvement in the performance index was achieved. The anti-fouling membrane was developed and fabricated into a module. The fabricated membrane module was tested with algae slurry and demonstrated improved fouling resistant properties, that can potentially reduce the cost and energy of the critical dewatering step. Test data were used to simulate operation of the overall process. The preliminary economic analysis was updated and modelled based on a 5000-acre algae farm. To the extent possible, the financial and operating assumptions used were the same as those used in the DOE’s 2022 projections for algae technology for CO2 capture and utilization. The results showed the proposed technology’s potential to significantly reduce the cost of CO2 capture compared to current options and that the high value products generated from the CO2 captured can make a step change in the cost of carbon capture. Plans to advance the technology to Phase 2B were developed and potential end-user partners were identified.
Maloney, James↗
Characterization of Solid Sorbent for Direct Air Capture of CO2 using a CFD-based Methodology
Computational Fluid Dynamics (CFD) was used to investigate the CO2 capture by a novel PIM sorbent developed in National Energy Technology Laboratory (NETL) for direct air capture (DAC) applications. The CO2 adsorption kinetics used in the CFD was developed using isotherm data and CO2 breakthrough data obtained from experiments. Effect on humidity on the CO2 adsorption was also investigated and compared with the CO2 adsorption in dry conditions.
Aziz, Hossain↗
CFD Model Development of a Small-Scale Fixed-Bed Reactor for Direct Air Capture of CO2
Direct air capture (DAC) is a promising approach to significantly reduce the CO2 concentration in the ambient air. This approach requires the extraction of CO2 from air with ultra dilute CO2 concentration which makes this approach more expensive than point source CO2 capture. Several efforts are being made in academics and industry to develop cost-efficient sorbents and solvents suitable for DAC. One of them is polymer with intrinsic microporosity (PIM) which is often used for CO2 capture because of its higher porosity and rigidity. A novel, cost-efficient aminated PIM sorbent, PF-15-TAEA, was developed at the National Energy Technology Laboratory for DAC applications. The current work is focused on the computational investigation of the CO2 capture by this novel sorbent from a gas mixture with ultra dilute concentration of CO2 in dry and humid conditions in a laboratory-scale fixed-bed reactor.
Aziz, Hossain↗
Investigating Combinations of Alkali Metal Oxides and Hydrogenation Catalysts for Reactive Capture of CO2 to Useful C1 Products
As the world endures environmental crises associated with climate change and the rise of atmospheric CO2 concentrations from anthropogenic CO2 emission, carbon capture and utilization (CCU) technologies are increasingly necessary. Reactive carbon capture (RCC) technologies, in which capture and conversion of CO2 occur in a single reactor, are more energetically and economically attractive by avoiding the need to purify, compress, and transport the captured CO2. To this end, dual function materials (DFMs) - composed of sorbents and catalysts co-dispersed on the same high surface area carrier - have been developed. The sorbent component allows for selective capture of CO2 from a gas stream and the catalyst component subsequently performs the in-situ conversion of the adsorbed CO2 upon introduction of a reactive gas (typically H2). The end product of the most established DFM, comprised of Ru and/or Ni with an alkaline sorbent, is methane via the CO2 methanation reaction. While renewable methane would be an excellent transition fuel, fossil methane is inexpensive (averaging $2.57/MMBTU in pre-pandemic 2019) and the economics of renewable methane utilization are noncompetitive. This requires the design and investigation of DFMs that enable CO2 capture and conversion to more valuable and more useful C1 products like CO or methanol (average price of methanol was $20.61/MMBTU in pre-pandemic 2019). These products can then be further upgraded to high energy density synthetic fuels, and related carbonaceous products, for more sustainable alternatives in industries that are difficult to decarbonize, specifically heavy duty vehicles and aviation. Herein, we report various sorbent + catalyst combinations to achieve the production of useful C1 products through reactive capture of CO2.
carbon capture↗
A Combined Water and CO2 Direct Air Capture System (CRADA 521)
The primary objective of this project is to demonstrate the outstanding technical and economic performance of a transformational Hybrid DAC (HDAC) technology that simultaneously captures CO2 and water from the air. Air is passed over a CO2 selective sorbent to remove ≥85% of the CO2 from the air stream. The atmospheric water extraction (AWE) section of the unit utilizes a novel isothermal pressure swing regeneration cycle with desiccant beds thermally coupled by heat pipes that provide a passive heat transfer mechanism to “cancel” the heat of water vapor adsorption. By proving system performance through this demonstration project, our initial technoeconomic analysis (TEA) will be validated, showing that HDAC technology: 1) is deployable in many more locations with limited water resources, 2) improves the financial returns, and 3) reduces risks from volatility in the price of CO2.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Advances in Carbon Capture and Use (CCU) Technologies: A Comprehensive Review and CO2 Mitigation Potential Analysis
One of society’s major current challenges is carbon dioxide emissions and their consequences. In this context, new technologies for carbon dioxide (CO2) capture have attracted much attention. One of these is carbon capture and utilization (CCU). This work focuses on the latest trends in a holistic approach to carbon dioxide capture and utilization. Absorption, adsorption, membranes, and chemical looping are considered for CO2 capture. Each CO2 capture technology is described, and its benefits and drawbacks are discussed. For the use of carbon dioxide, various possible applications of CCU are described, starting with the utilization of carbon dioxide in agriculture and proceeding to the conversion of CO2 into fuels (catalytic processes), chemicals (photocatalytic processes), polymers, and building supplies. For decades, carbon dioxide has been used in industrial processes, such as CO2-enhanced oil recovery, the food industry, organic compound production (such as urea), water treatment, and, therefore, the production of flame retardants and coolants. There also are several new CO2-utilization technologies at various stages of development and exploitation, such as electrochemical conversion to fuels, CO2-enhanced oil recovery, and supercritical CO2. At the end of this review, future opportunities are discussed regarding machine learning (ML) and life cycle assessment (LCA).
Peres, Christiano B.↗
Metallic Phase-Free Zn-Al Mixed Oxide Dual Function Materials Enable High Co Selectivity in Reactive Carbon Capture From Dilute Streams
Scaling conventional carbon capture and utilization methods can be limited by cost and permitting issues associated with transportation of captured CO2. Reactive carbon capture (RCC), in which a single solid-phase dual function material (DFM) is used to both capture CO2 from dilute streams (e.g., flue gas) and catalytically convert the bound species to products in a single unit operation, has the potential to reduce energy and capital costs by over 50% relative to separate capture and conversion. To incentivize adoption, high-value products such as methanol and CO should be targeted. Appealingly, CO can be produced at atmospheric pressure, thereby lowering overall H2 demand; however, high reaction temperatures (> 600 degrees C) and the use of oxidizable transition metals, such as Ni, are often necessary to drive the reverse water-gas shift (RWGS) during reactive desorption of the bound CO2. The sensitivity of these transition metals to oxygen undercuts their utility in point source RCC. To further derisk RCC, it is essential to develop metallic-phase free DFMs that are insensitive to residual oxygen in flue gas and can achieve selective reactive desorption to CO at moderate pressures (< 400 degrees C). To this end, we have developed K-modified Zn-Al mixed oxides (K/ZnAlOx) to convert captured CO2 to CO with > 97% selectivity and yields up to 53% of captured CO2 at 400 degrees C. Complementary in situ spectroscopy studies revealed the role of K-modification in improving RCC performance of unmodified ZnAlOx. The top performing DFM was also subjected to extended RCC cycling with oxygen co-fed with CO2 during the capture test to assess durability under simulated flue gas.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Crystal Engineering of Hydrogen Bonding for Direct Air Capture of CO2: A Quantum Crystallography Perspective
Rising atmospheric CO2 levels demand efficient and sustainable carbon capture solutions. Direct air capture (DAC) via crystallizing hydrogen-bonded frameworks such as carbonate salts has emerged as a promising approach. This review explores the potential of crystal engineering, in tandem with advanced quantum crystallography techniques and computational modeling, to unlock the full potential of DAC materials. We examine the critical role of hydrogen bonding and other noncovalent interactions within a family of bis-guanidines that governs the formation of carbonate salts with high CO2 capture capacity and low regeneration energies for utilization. Quantum crystallography and charge density analysis prove instrumental in elucidating these interactions. A case study of a highly insoluble carbonate salt of a 2,6-pyridine-bis-(iminoguanidine) exemplifies the effectiveness of these approaches. However, challenges remain in the systematic and precise determination of hydrogen atom positions and atomic displacement parameters within DAC materials using quantum crystallography, and limitations persist in the accuracy of current energy estimation models for hydrogen bonding interactions. Future directions lie in exploring diverse functional groups, designing advanced hydrogen-bonded frameworks, and seamlessly integrating experimental and computational modeling with machine learning. This synergistic approach promises to propel the design and optimization of DAC materials, paving the way for a more sustainable future.
36 MATERIALS SCIENCE↗
NH 4 OH Looping with Membrane CO 2 Absorber and Distributed Stripper for Enhanced Algae Growth
The University of Kentucky Center for Applied Energy (UK CAER) has devised a unique, integrated CO2 capture and utilization technology. CO2 from coal-fired power generation flue gas is first captured at half the operating cost of a typical aqueous CO2 capture system (CCS), distributed in an aqueous stream and then fixed by algae in bioreactors where the algae production is increased by 50% over that with a typical intermittent nutrient feeding system. Lower CCS operating cost is achieved by eliminating the flue gas pretreatment step for cooling and SO2 removal, eliminating steam extraction from the power generation steam cycle for solvent regeneration, and eliminating CO2 compression. Higher algae production is achieved by continuous, just-in-time nutrient feed to the bioreactors directly from a distributed solvent regenerator, which maintains the bioreactor pH for optimum growth. The process starts with a uniquely configured membrane absorber, where the flue gas is indirectly contacted with an ammonium hydroxide (NH4OH) solvent. Dissolved NH3 is attractive for both CO2 capture and as an algae nutrient. For CO2 capture it is inexpensive, has a low regeneration energy, is thermally- and oxidatively-stable and has a viscosity near that of water, which makes is easy to transport. Numerous studies have shown that the scrubbing capacity of NH3 is approximately 0.9-1.2 kg of CO2/kg of NH3, with a CO2 removal efficiency of ~99% and half the solvent regeneration energy than that of 30 wt% MEA[1, 2, 3]. NH3 is attractive as an algae nutrient due to its low cost. The rich NH4OH solvent is pumped to a set of distributed regenerators which are co-located with the algae bioreactors. Solvent pumping, transport and distribution reduces the balance of plant (BOP) cost compared to a typical aqueous CCS related to the flue gas duct and boost fan required to transport the flue gas. The energy required for the distributed solvent regeneration is supplied by solar-thermal panels eliminating the need for steam extraction from the power generation steam cycle. After solvent regeneration, the product stream contains both the CO2 captured from the flue gas and volatized NH3 from the solvent. This product stream is fed directly to the bioreactors, eliminating the need for compression of the CO2 stream. The relative amounts of CO2 and NH3 in the product stream are adjusted and controlled by a controlling the regeneration conditions (pressure and temperature). The continuous feed of the right ratio of nutrients overcomes the typical inhibition of algae growth resulting from frequent pH swings in the bioreactor due to unbalanced (intermittent) feeding systems for CO2 and N. Also, because the regenerators will operate at pressure and be located in close proximity to the bioreactors, there is no worry about pressure drop when sparging the gas into the algae. Sparging produces small bubbles which is beneficial for mass transfer efficiency. One known challenge when using an NH4OH solvent is high NH3 emission. Hydrophobic membranes are used for CO2 capture using an aqueous NH3 solution[4, 5] without the direct contact between flue gas and aqueous solution. Additionally, UK CAER CO2 capture and utilization process manages NH3 slip in three extra measures. First, NH3 slip is minimized by working with minimal species partial pressure, which is proportional to the concentration in the liquid. Hence, lowering the capture solvent concentration will lower the NH3 partial pressure. Second, UK CAER’s previous work has demonstrated that the addition of Zn2+ into NH3 solutions to chelate the NH3 can reduce NH3 volatility. Third, the configuration of the membrane CO2 absorber utilizes condensed water from the flue gas to continually wash the gas-side of the membrane to reduce fouling and recapture NH3 slip. Additional details about the UK CAER unique, integrated CO2 capture and utilization technology will be presented along with technology development plans. Diao, N., Q. Li, and Z. Fang. 2004. Heat transfer in ground heat exchangers with groundwater advection. International Journal of Thermal Sciences. 43: 1203-1211, He, Q., M. Chen, L. Meng, K. Liu, and W. Pan. 2004. Study on Carbon Dioxide Removal from Flue Gas by Absorption of Aqueous Ammonia. Western Kentucky University. Yeh, A.C., and H. Bai. 1999. Comparison of ammonia and monoethanolamine solvents to reduce CO2 greenhouse gas emissions. The Science of the Total Environment. 228: 121-133, Villeneuve, K., D. Roizard, J.C. Remigy, M. Iacono, and S. Rode. 2018. CO2 capture by aqueous ammonia with hollow fiber membrane contactors: Gas phase reactions and performance stability. Separation and Purification Technology, 199: 189-197, Toro Molina, C., and C. Bouallou. 2016. Carbon dioxide absorption by ammonia intensified with membrane contactors. Clean Techn Environ Policy 18, 2133–2146 (2016)
20 FOSSIL-FUELED POWER PLANTS↗
Deep Learning Potential For Investigation of Chemical Conversion of CO2 at Air-Reactive Deep Eutectic Solvent Interface
Capturing CO2 from air is urgent to battle against the climate change. Traditional CO2 capture by alkaline solution or aqueous amine has high regeneration cost, equipment corrosion, and amine leakage. Deep eutectic solvents (DESs) are promising alternatives with low corrosion, non-toxicity, and biodegradable nature. Functionalized DESs can capture and convert CO2 at low partial pressures. Developing reactive DESs for efficient CO2 capture needs a foundational understanding of the reaction-transport coupling of CO2 at the air-DES interface. In this study, we develop a deep learning potential (DLP) to investigate the absorption and reaction of CO2 at the air-DES interface (DES: 1-ethyl-3-methylimidazolium 2-cyanopyrrolide ([Emim][2-CNpyr]) and ethylene glycol (EG)). The DLP model allows us to simulate chemical reactions at a lower computational cost with ab initio accuracy. By analyzing reaction free energy surfaces, molecular interactions among CO2, DES components and reaction products, and transport of CO2 through the interface, we identify three main reaction pathways of CO2 at the interface: forming carboxylate with [Emim], carbamate with [2-CNpyr], and carbonate with EG. The mechanistic understanding of CO2 chemisorption at the interface will facilitate the development of novel direct air capture technology using DESs.
Nguyen, Manh Tien↗
Recent Cryogenic Carbon Capture™ Field Test Results
Sustainable Energy Solutions (SES) has been developing Cryogenic Carbon Capture™ (CCC) since 2008. In that time, two processes have been developed, the External Cooling Loop and Compressed Flue Gas CCC processes (CCC-ECL and CCC-CFG, respectively). The CCC-ECL process cools the flue gas with an external refrigerant loop. This process currently captures up to 1 tonne of CO2 per day (TPD). SES has tested CCC-ECL on real flue gas slip streams from subbituminous coal, bituminous coal, biomass, natural gas, shredded tires, and municipal waste fuels at field sites that include utility power stations, heating plants, cement kilns, and pilot-scale research reactors. The CO2 concentrations from these tests ranged from 5 to 22% on a dry basis. CO2 capture ranged from 95-99+% during these tests. Several other condensable species were also captured including NO2, SO2 and PMxx at 95+%. NO was also captured at a modest rate. The CCC-CFG process has been scaled up to a 0.25 ton per day system. This system has been tested on real flue gas streams including subbituminous coal, bituminous coal, and natural gas at field sites that include utility power stations, heating plants, and pilot-scale research reactors. CO2 concentrations for these tests ranged from 5 to 15% on a dry basis. CO2 capture ranged from 95-99+% during these tests. Several other condensable species were also captured including NO2, SO2, and PMxx at 95+%. NO was also captured at 90+%. Hg capture was also verified and the resulting effluent from CCC-CFG was below a 1ppt concentration. This paper will focus on discussion of the capabilities of CCC generally, the results of CCC-ECL field testing, and future steps surrounding the development of this technology. Test results that will be presented have been collected during 9 months of testing at a commercial power plant under funding from the US Department of Energy (DOE) and the host utility. Testing of one of the systems at a commercial cement plant in the United States will also be discussed. During this testing, the system captured CO2 from the cement plant and stored the CO2 in pressurized tanks. These tanks were provided to a partner company that later used the CO2 in a CO2 utilization demonstration. The CO2 was utilized to cure concrete manufactured using cement from the same plant where the CO2 was captured. This integrated capture and utilization demonstration was the first time that the cement industry has shown in the field that it can sequester its CO2 emissions in its main product stream. This represents a potential game changing solution for industrial CO2 emissions. Operational data and host-site feedback indicate that the CCC process is ideally suited for deployment into a variety of commercial environments. A few areas of de-risking remain to make sure the technology can meet very strict industrial reliability standards. These areas of de-risking are identified and discussed. The product CO2 is shown to meet specification for many uses including industrial and merchant applications. The technology is nearing readiness for deployment at commercial scale and several initial target markets have been identified.
20 FOSSIL-FUELED POWER PLANTS↗
Direct Air Capture of CO2 (DAC) [Tech Snapshot]
Researchers at Los Alamos have extensive capabilities in design, testing and optimization of: (1) new capture materials based on membrane separation, amine and other solvent and sorbent separation, and porous materials; (2) biological capture methods, particularly algae and plants; (3) full-scale systems using science-based virtual learning; and (4) system performance under specific meteorological conditions, impacts of CO2 capture via atmospheric data and simulations, and availability of energy and storage capacity. The goal for Los Alamos is advancing our physical technologies and engineered systems approaches from the development phase to a minimal viable product in the energy sector for commercial purposes. Los Alamos is seeking strategic commercialization partners to work with us in advancing these capabilities and technologies for commercial viability.
54 ENVIRONMENTAL SCIENCES↗
CO 2 Capture Using Electrochemically Mediated Amine Regeneration
We describe the current status of our research on, and the development of, the Electrochemically Mediated Amine Regeneration (EMAR) process for the capture of CO2 from flue gases. The absorption step in the EMAR process is the same as in the widely used amine process, but the desorption step is accomplished electrochemically as opposed to by a thermal swing used in the amine process. Our laboratory unit has operated continuously for over 200 h, spanning 130 absorption/desorption cycles. We have established an understanding of the thermodynamics of the EMAR process and provided engineering estimates of key features (energetics and sizing) of this technology. The EMAR system does not rely on steam integration, making it a truly plug-and-play unit that can be easily deployed for a range of applications. The EMAR system can also be scaled-down for distributed, modular, and small-scale operations (e.g., stainless steel mini-mills, etc.). Here, results to date indicate that the EMAR process has the potential to be a viable option for post-combustion CO2 capture.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Thermally Enhanced Acidity for Regeneration of Carbon Dioxide Sorbent
The thermal regeneration of CO2 sorbent is the most energy-consuming step in the CO2-capturing process. Although the addition of an acid can induce CO2 release, it does not regenerate the sorbent because the acid forms a salt with the basic sorbent and diminishes its capability for capturing CO2. In this work, a novel approach based on thermally enhanced acidity was studied. This approach utilizes an additive that does not affect the sorbent at room temperature, but its acidity significantly increases at elevated temperatures, which assists the thermal release of CO2. M-cresol was added to an aqueous solution of morpholine. The CO2 capture and release of the mixture were compared to those of a control solution without m-cresol. The amounts of carbamate, bicarbonate, and unreacted morpholine were quantitatively determined using 1H NMR and weight analysis. The results showed that m-cresol did not affect the reactivity of morpholine in the formation of carbamate with CO2 at room temperature. At elevated temperatures, the acidity of m-cresol increased according to Van’t Hoff’s equation, which resulted in a significantly higher rate of CO2 release than that of the control. Given the low cost of m-cresol and its derivatives, this approach could lead to practical technology in the near future.
Energy & Fuels↗
Advanced Sensors for In-Situ Amine Degradation Monitoring in Post-Combustion Carbon Capture
In order to improve the long-term performance of post-combustion carbon capture technologies, improvements to the detection of solvent degradation or reduction in CO2 capture efficiency are necessary. A pair of sensors were deployed to the National Carbon Capture Center’s (NCCC) to monitor CO2 capture and solvent degradation. The CO2 sensors were located to measure before capture and after capture concentrations of CO2 to measure the capture efficiency of the solvent system. Amine degradation sensors were located at four locations along the main solvent lines corresponding to CO2 loading and temperature: hot rich, cold rich, hot lean, and cold lean. Experimental results from laboratory tests using the sensors are shown, along with prototype designs that were deployed to the field site.
Brister, Matthew↗
Decarbonization of the Iron and Steel Sector: Challenges and Opportunities
The iron and steel industry is one of the largest contributors to industrial emissions in the United States (U.S.). As this industry represents an impactful opportunity for industrial decarbonization, this paper presents the techno-economics of retrofitting iron/steel plants in the U.S. with post-combustion carbon dioxide (CO2) capture technology. For a representative base plant, this analysis considers an integrated steel mill, including a blast furnace (BF) and basic oxygen furnace (BOF), and evaluates CO2 capture as applied to the three largest and highest concentration emission sources of these facilities. A levelized cost of CO2 captured (LCOC) of $80.3/tonne CO2 and $80.7/tonne CO2 was estimated for a retrofit site with 99 and 90 percent capture, respectively.
Henry, Samuel [NETL Site Support Contractor, Natio↗
Development of a rate-based ENRTL-RK process model for a water-lean solvent
Advanced water-lean solvents (WLS) for post-combustion CO2 capture offer several advantages over the aqueous amine solvents . WLS have lower parasitic energy penalty, lower corrosion, lower temperature and high-pressure CO2 regeneration leading to lower cost of CO2 capture. RTI International, with funding from the US Department of Energy, has been developing its novel water-lean solvent, that has shown specific reboiler duty of 2.3 GJ/t-CO2 at the 60-kWe pilot testing unit (Tiller Plant, SINTEF, Norway) and 2.6 GJ/t-CO2 at the engineering scale testing system (12 MWe) at the Technology Centre Mongstad (TCM) in Norway. All heat duties, including the one from TCM testing, were consistent with Aspen Plus modeling of the specific configuration of each test plant. This work focuses on the development of a detailed process model using in-house laboratory measurements and process data at pilot scale. The eNTRL-RK model used in this work is based on an unsymmetric activity coefficient model with the reference states chosen to be pure liquids for solvents and ideal dilute solution at unit solute molality (resulting in activity coefficient of unity at infinite dilution) for electrolytes. It uses the Redlich-Kwong equation of state for vapor phase properties and Henry’s law for solubility of supercritical gases. The model was validated using process data from the pilot-scale campaign at the Tiller plant, and the engineering scale test campaign at TCM. Data on CO2 capture rate, absorber, and regenerator temperature profiles and specific reboiler duties from two different test campaigns at Tiller and TCM, were used to further refine and validate the model and the model compares favorably to experimental data. The validation results against TCM campaign will be presented in this work.
CO2 capture↗