SEARCH · Search NASA

Results for “CONTROL AREA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Seasonal performance evaluation of zero-superheat active refrigerant charge control for variable-speed heat pumps

Heat pumps account for a significant portion of electricity consumption in buildings, making their energy efficiency a critical area of research. Control optimization is recognized as an effective approach for enhancing the efficiency of building HVAC systems. Specifically, since the efficiency of heat pumps increases with reduced superheat and the optimal refrigerant charge level varies with operating conditions, zero-superheat active charge control is a promising strategy to maximize the system’s COP. However, due to its complexity, this control strategy remains in the research phase and has only been tested under limited operating conditions. This paper proposes a methodology to evaluate the seasonal performance improvement of zero-superheat active charge control across a full range of heating conditions in buildings. The methodology includes the development of an optimal controller that utilizes an accumulator to store excess refrigerant and manages the active charge level at zero superheat through subcooling control, as well as the creation of a detailed physics-based heat pump model. Targeted a 3-ton variable-speed heat pump with R410A refrigerant, we selected ten U.S. cities representing different climate regions for seasonal performance evaluation. Our simulations indicate that, depending on the climate conditions, the optimal control strategy could achieve energy savings ranging from 5.8 % to 8.0 % over the entire heating season. These results suggest that zero-superheat active charge control, combined with coordinated compressor and fan speeds, could substantially improve the energy efficiency of heat pump systems while maintaining the required heating capacity.

Guo, Fangzhou↗

DOE OSTI2021

Control rod damping system

A damping area or “dash pot” on the upper ends of control rods absorb energy from dropped control rod assemblies without narrowing the diameter of guide tubes. As a result, coolant can freely flow through the guide tubes reducing boiling water issues. The dampening area reduces a separation distance between an outside surface of the control rod and an inside surface of the guide tubes decelerating the control rods when entering a top end of the guide tubes. In another example, the dampening area may be located on a drive shaft. The dampening area may have a larger diameter than an opening in a drive shaft support member that decelerates the drive shaft when dropped by a drive mechanism.

Snuggerud, Ross Douglas↗

DOE OSTI2023

Control rod damping system

Snuggerud, Ross Douglas↗

DOE OSTI2025

Stomata in-sight: Integrating live confocal microscopy with leaf gas exchange and environmental control

Stomatal anatomy (aperture area, length, and width) influences leaf-level physiology traits including conductance to water vapor. Stomatal anatomy can be visualized in situ by microscopy, but the difficulty of regulating the atmospheric environment of a microscope stage means that the conditions under which imaging is done are rarely physiologically relevant. Alternatively, leaf gas exchange instruments that measure gas fluxes reflect stomatal anatomical characteristics in aggregate, but the relative strengths of anatomical traits to control water use (e.g. size vs density) cannot be firmly established. To reconcile the microscopic stomatal characteristics with leaf-level gas exchange, we describe a tool that combines laser scanning confocal microscopy, gas exchange instruments, and machine-learning image analysis to simultaneously observe anatomical characteristics of many (>40) stomata alongside leaf-level traits like photosynthesis, transpiration, and stomatal conductance. We demonstrate how the tool has the resolution capable of quantifying aperture sizes and variability in maize (Zea mays) leaves under 5 steady-state light/pCO 2 treatments while tightly controlling other environmental variables like relative humidity and temperature. A model used to calculate stomatal conductance from measured apertures and stomatal density accurately matched stomatal conductance measured by gas exchange. This technical advancement will provide insight on how stomatal anatomy and function trade off to influence stomatal conductance and leaf-level water use efficiency.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

Exploration of Optimizing FPGA-based Qubit Controller for Experiments on Superconducting Quantum Computing Hardware

This work explores avenues and target areas for optimizing FPGA-based control hardware for experiments conducted on superconducting quantum computing systems and serves as an introduction to some of the current research at the intersection of classical and quantum computing hardware. With the promise of building larger-scale error-corrected quantum computers based on superconducting qubit architecture, innovations to room-temperature control electronics are needed to bring these quantum realizations to fruition. The QICK (Quantum Instrumentation Control Kit) is one leading experimental FPGA-based implementations. However, its integration into other experimental quantum computing architectures, especially those using superconducting radiofrequency (SRF) cavities, is largely unexplored. We identify some key target areas for optimizing control electronics for superconducting qubit architectures and provide some preliminary results to the resolution of a control pulse waveform. With optimizations targeted at 3D superconducting qubit setups, we hope to bring to light some of the requirements in classical computational methodologies to bring out the full potential of this quantum computing architecture, and to convey the excitement of progress in this research.

43 PARTICLE ACCELERATORS↗

DOE OSTI2023

A 30% reduction in switchgrass rhizome reserves did not decrease biomass yield

Abstract A long‐standing question in perennial grass breeding and physiology is whether yield improvement strategies could compromise winter survival. Since perennial grasses rely on stored carbohydrates for winter maintenance and spring regrowth, yield improvement strategies could reduce winter survival if they increase biomass and grain yields at the expense of carbon allocation to storage. Therefore, it is crucial to comprehend the dependence of regrowth on storage reserves. We experimentally depleted switchgrass ( Panicum virgatum L.) rhizome reserves by storing rhizomes for 2 weeks at 5°C (control treatment) and 25°C (reserve‐depleted treatment). During the storage period rhizome respiration was 5.3× higher at 25°C (0.010 μmol CO 2 g −1 min −1 at 5°C vs. 0.054 μmol CO 2 g −1 min −1 at 25°C; p < 0.0001) and the starch content was depleted by 30% by the end of storage. Surprisingly, reserve‐depleted switchgrass had 60% larger leaf area (LA; LA control = 149 cm 2 pot −1 vs. LA depleted = 239 cm 2 pot −1 ; p = 0.013) and produced ~40% more aboveground biomass than control plants (9.46 g pot −1 vs. 6.63 g pot −1 ; p = 0.112). In addition, reserve‐depleted switchgrass restored its rhizome starch reserves to pre‐storage levels. Switchgrass showed a large plasticity among its source‐sink components to buffer the imposed reserve depletion. It increased plant photosynthesis by increasing the photosynthetic leaf area while keeping photosynthesis constant on a leaf area basis and readjusted the timing and activity of sink organs. These results suggest that switchgrass, and potentially other perennial grasses, largely over‐invest in storage reserves. Therefore, current breeding strategies in perennial grasses aimed to extend the aboveground growing season should not compromise crop persistence. Our study also has implications on long‐term yield dynamics as it highlights sink limitations as potential driver of the yield decline commonly observed in perennial grasses 5+ years after cultivation.

Tejera‐Nieves, Mauricio↗

DOE OSTI2021

Harnessing autocatalytic reactions in polymerization and depolymerization

Abstract Autocatalysis and its relevance to various polymeric systems are discussed by taking inspiration from biology. A number of research directions related to synthesis, characterization, and multi-scale modeling are discussed in order to harness autocatalytic reactions in a useful manner for different applications ranging from chemical upcycling of polymers (depolymerization and reconstruction after depolymerization), self-generating micelles and vesicles, and polymer membranes. Overall, a concerted effort involving in situ experiments, multi-scale modeling, and machine learning algorithms is proposed to understand the mechanisms of physical and chemical autocatalysis. It is argued that a control of the autocatalytic behavior in polymeric systems can revolutionize areas such as kinetic control of the self-assembly of polymeric materials, synthesis of self-healing and self-immolative polymers, as next generation of materials for a sustainable circular economy. Graphic Abstract

36 MATERIALS SCIENCE↗

DOE OSTI2021

Optically enhanced patternable photosensitivity via oxygen excitation

The present disclosure relates to a method for performing a three dimensional (3D) printing process. A primary light beam having a wavelength sufficient to initiate polymerization of a photoresin is generated and patterned into a patterned primary beam. The patterned primary beam is directed toward an ultraviolet (UV) or visible light sensitive photoresin to initiate polymerization of select areas of the photoresin. The photoresin is also illuminated with a secondary light beam having a wavelength of at least one of about 765 nm, 1064 nm, or 1273 nm. The secondary light beam stimulates triplet oxygen into singlet oxygen, which controls oxygen inhibition in additional areas bordering the select areas, to enable controlled polymerization inhibition in the additional areas bordering the select areas.

Hensleigh, Ryan↗

DOE OSTI2024

End-Use Savings Shapes Measure Documentation: Thermostat Control for Load Shedding in Large Offices

This documentation focuses on a single End-Use Savings Shape measure - thermostat control for load shedding. The thermostat control for load shedding measure applies heating and cooling temperature setpoint offsets for reducing the heating and cooling load during peak window. The measure takes daily peak load schedule inputs generated by the method "Dispatch Schedule Generation" described in the "Supplemental Documentation: Dispatch Schedule Generation for Demand Flexibility Measures" to determine the start and end times of the peak window, and then adjusts the thermostat cooling and/or heating setpoints by an offset value from original schedules during the peak window to reduce the HVAC or whole building daily peak load. The measure is flexible and allows users to adjust the heating and cooling offset values respectively, but for this study, the adjustment for heating and cooling setpoints are set to -2 degrees Celsius and +2 degrees Celsius by default. The measure provides options of adding rebound control period (default 2 hours) after peak windows for the setpoints to be ramped back to default values, to prevent the system from generating higher peak demand with step changes of setpoints in post-peak periods . This measure is applicable t o large offices equipped with electric HVAC system (either electric cooling only or both electric heating and cooling), which account for approximately 8.72% of the ComStock floor area. The thermostat control for load shedding measure demonstrates 2-5% daily peak demand reduction and 0.068% total site energy savings (3 trillion British thermal units [TBtu]) for the U.S. commercial building stock modeled in ComStock.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

AI for Science: Report on the Department of Energy (DOE) Town Halls on Artificial Intelligence (AI) for Science

The report documents the DOE Town Halls held during 2019 at Argonne National Laboratory, Oak Ridge National Laboratory, Lawrence Berkeley National Laboratory, and in Washington, DC. From July to October 2019, the Argonne, Oak Ridge, and Berkeley National Laboratories hosted a series of four town hall meetings attended by more than 1,000 U.S. scientists and engineers. The goal of the town hall series was to examine scientific opportunities in the areas of artificial intelligence (AI), Big Data, and high-performance computing (HPC) in the next decade, and to capture the big ideas, grand challenges, and next steps to realizing these opportunities. In this report and in the Department of Energy (DOE) laboratory community, we use the term “AI for Science” to broadly represent the next generation of methods and scientific opportunities in computing, including the development and application of AI methods (e.g., machine learning, deep learning, statistical methods, data analytics, automated control, and related areas) to build models from data and to use these models alone or in conjunction with simulation and scalable computing to advance scientific research. The AI for Science town hall discussions focused on capturing the transformational uses of AI that employ HPC and/or data analysis, leveraging data sets from HPC simulations or instruments and user facilities, and addressing scientific challenges unique to DOE user facilities and the agency’s wide-ranging fundamental and applied science enterprise.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Project 57 Air Monitoring Report: (Jan 1 - Dec 31 2018)

During the late 1950s, the Atomic Energy Commission (AEC) (now the U.S. Department of Energy [DOE]) conducted a series of safety experiments to determine if a nuclear device subjected to a large conventional explosives detonation would result in a nuclear yield. The AEC obtained temporary use of a large portion of western Emigrant Valley from the U.S. Department of Defense (DOD) for one of these experiments: Project 57. Following the Project 57 safety experiment, the AEC fenced the contaminated area and returned control of the surrounding land to the DOD. Emigrant Valley is part of the Nevada Test and Training Range (NTTR). For safety and security reasons, access to the NTTR is controlled using both physical (i.e., fences) and administrative (e.g., signs and postings) controls. Therefore, the public cannot access the Project 57 site and there are no known human receptors that routinely access the site. Project 57 was detonated on April 24, 1957, in Emigrant Valley approximately 13 mi (21 km) northeast of the north end of Yucca Flat. This test was undertaken to develop: (1) a means of estimating immediate distribution and long-term redistribution of plutonium dispersed during a nonnuclear detonation; (2) biomedical evaluation techniques for use in likely plutonium-laden environments; (3) methods of decontaminating ground areas, pavements, and building materials; and (4) alpha survey instruments and field monitoring procedures to promptly estimate contaminant deposition. Although the test did not result in the fission of nuclear materials, it did disseminate plutonium across the ground surface. Various radiological surveys have been performed in the area since Project 57 was conducted. The AEC delineated the area containing radioactive material based on radioactivity surveys performed shortly after the test was conducted. A designated Contamination Area (CA), marked by a fence, was established later. The distribution of americium-241 (Am-241) in the area was determined again in a 1997 flyover, which showed Am-241 ranging from as much as 70,000 counts per second (cps) at ground zero to background (<70 cps). This survey also documented Am-241 radioactivity on the ground surface beyond the east side CA fence at levels of up to 150 cps. In 2007, the DOE expanded the CA by posting “Contamination Area” signs 200 ft to 400 ft (60 m to 120 m) beyond the original fence, which formed a new CA boundary.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2020

Characterizing Physical Properties of Streambed Interface Sediments Using In Situ Complex Electrical Conductivity Measurements

Streambed sediment physical properties such as surface area, are difficult to quantify in situ but exert a high-level control on a wide range of biogeochemical processes and sorption of contaminants. We introduce the use of complex electrical conductivity (CC) methods (also known as spectral-induced polarization (SIP)) that measure both real and imaginary conductivity to noninvasively and efficiently characterize shallow streambed sediments. We explore the method through synthetic modeling, laboratory, and field measurements to demonstrate the sensitivity of imaginary conductivity to sediment surface area, controlled in part by fine-grained iron oxides produced by anoxic groundwater discharge. Laboratory measurements verify expected relationships between CC parameters and sediment properties. Synthetic modeling using a 1D analytical model illustrates the influence of water layer depth and conductivity on the field CC measurements made at the streambed-stream water interface. Specifically, the inverted sediment imaginary conductivity is less impacted by uncertainty in the water layer depth and conductivity relative to the real conductivity and phase shift. Field CC measurements along a landfill-impacted river reveal discrete streambed zones with enhanced bulk surface area generally corresponding to anoxic groundwater discharge zones with high concentrations of fine-grained iron oxide precipitates.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Towards On-Chip Learning for Low Latency Reasoning with End-to-End Synthesis

The Software Defined Architectures (SODA) Synthesizer is an open-source compiler-based tool able to automatically generate domain-specialized systems targeting Application-Specific Integrated Circuits (ASICs) or Field Programmable Gate Arrays (FPGAs) starting from high-level programming. SODA is composed of a frontend, SODA-OPT, which leverages the multilevel intermediate representation (MLIR) framework to interface with productive programming tools (e.g., machine learning frame-works), identify kernels suitable for acceleration, and perform high-level optimizations, and of a state-of-the-art high-level synthesis backend, Bambu from the PandA framework, to generate custom accelerators. One specific application of the SODA Synthesizer is the generation of accelerators to enable ultra-low latency inference and control on autonomous systems for scientific discovery (e.g., electron microscopes, sensors in particle accelerators, etc.). This paper provides an overview of the flow in the context of the generation of accelerators for edge processing to be integrated in transmission electron microscopy (TEM) devices, focusing on use cases from precision material synthesis. We show the tool in action with an example of design space exploration for inference on reconfigurable devices with a conventional deep neural network model (LeNet). Finally, we discuss the research directions and opportunities enabled by SODA in the area of autonomous control for scientific experimental workflows.

Castellana, Vito G.↗

DOE OSTI2023

pystorms: A simulation sandbox for the development and evaluation of stormwater control algorithms

Advances in cyber–physical technologies have enabled real-time sensing and adaptive control of stormwater infrastructure. These smart stormwater systems allow for inexpensive, minimally-invasive stormwater control interventions in lieu of new construction. Importantly, however promising the area of smart stormwater control, there still remain barriers – for experts and novices alike – to access shared tools and methods for investigating, developing, and contributing to it. In an effort to make smart stormwater control research more methodical and accessible, we present pystorms, an open-source Python-based simulation sandbox that facilitates the quantitative evaluation and comparison of control strategies. pystorms consists of a collection of real world-inspired smart stormwater control scenarios on which any number of control strategies can be applied and tested via an accompanying Python programming interface and coupled stormwater simulator. pystorms provides a framework for the rigorous and efficient evaluation of smart stormwater control methodologies across diverse watersheds with only a few lines of code.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

End-Use Savings Shapes Measure Documentation: Thermostat Control for Load Shifting in Large Offices

This documentation focuses on a single end-use savings shape measure - thermostat control for load shifting. The thermostat control for load shifting measure applies heating and cooling temperature setpoint adjustment for pre-conditioning before the peak window. The measure takes daily peak load schedule inputs generated by the method "Dispatch Schedule Generation" described in the "Supplemental Documentation: Dispatch Schedule Generation for Demand Flexibility Measures" to determine the start time of the peak window, and then adjusts the thermostat cooling or heating setpoints by a specified offset value from original schedules to precool or preheat the space , for a specified length of time before the start of peak window, and thus shifts load in the peak window to the pre-conditioning period. The measure is flexible and allows users to adjust the heating and cooling offset values and length of pre-conditioning period, but for this study, the load shifting strategy is applied as pre-cooling only (adjusting only cooling setpoints). The default adjustment for cooling setpoints is set to -1 degrees Celsius , and the default duration of pre-cooling is 1 hour. This measure is applicable to large offices equipped with electric HVAC system, which account for approximately 8.72% of the ComStock floor area. The thermostat control for load shifting measure demonstrates -1% daily peak demand reduction and 0% total site energy savings (0 trillion British thermal units [TBtu]) for the U.S. commercial building stock modeled in ComStock.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2021

CPS Testbed Architectures for WAMPAC using Industrial Substation and Control Center Platforms and Attack-Defense Evaluation

Advanced persistent threats and cyberattacks can impact wide-area monitoring, protection, and control (WAMPAC) system operation. Many cyber-physical system (CPS) testbeds have been developed for attack-defense experimentation and attack-resiliency tools evaluation for WAMPAC, but they are limited to a simulation-and-emulation based environment. This paper presents a quasi-realistic CPS attack-defense testbed-based framework for WAMPAC applications using the industrial substation and control center platforms such as eTerra integrated with the hardware-in-the-loop CPS smart grid testbed available at Iowa State University. The proposed framework includes various combinations of industry-grade substation and control center platforms, communication topologies, real-time digital simulators, and a novel cyber-physical distributed intrusion-and-anomaly detection system (D-IADS) for WAMPAC applications. The D-IADS includes a master at the control center and geographically distributed sensor devices at each substation. Each D-IADS sensor deployed at a substation or control center network monitors ingress and egress traffic, detect intrusions, and dispatch alerts to the D-IADS master. The D-IADS master centrally monitors and analyze the alerts and controls D-IADS sensors. We considered an EMP60 synthetic CPS grid as a case study to demonstrate the framework and proposed D-IADS for WAMPAC applications against cyberattack vectors such as Man-in-the-Middle DNP3 attack, denial-of-service, and data-integrity attacks.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2021

Optimization of Magnesium‐Doped Lithium Metal Anode for High Performance Lithium Metal Batteries through Modeling and Experiment

Abstract Lithium (Li)‐magnesium (Mg) alloy with limited Mg amount, which can also be called Mg‐doped Li (Li‐Mg), has been considered as a potential alternative anode for high energy density rechargeable Li metal batteries. However, the optimum doping‐content of Mg in Li‐Mg anode and the mechanism of the improved performance are not well understood. Herein, density functional theory (DFT) calculations are used to investigate the effect of Mg amount in Li‐Mg anode. The Li‐Mg with about 5 wt. % Mg (abbreviated as Li‐Mg5) has the lowest absorption energy of Li, thus all the surface area can be “controlled” by Mg atoms, leading to the smooth and continuous deposition of Li on the surface around the Mg center. A localized high concentration electrolyte enables Li‐Mg5 to exhibit the best cycling stability in Li metal batteries with high‐loading cathode and lean electrolyte under 4.4 V high‐voltage, which is approaching the demand of practical application. This electrolyte also helps generate an inorganic‐rich solid electrolyte interphase, which leads to smooth, compact and less corrosion layer on the Li‐Mg5 surface. Both theoretical simulations and experimental results prove that Li‐Mg5 has optimum Mg content and gives best battery cycling performance.

Gao, Peiyuan↗

DOE OSTI2021

Optimization of Magnesium-Doped Lithium Metal Anode for High Performance Lithium Metal Batteries through Modeling and Experiment

Lithium (Li)-magnesium (Mg) alloy with limited Mg amount, which can also be called Mg-doped Li (Li-Mg), has been considered as a potential alternative anode for high energy density rechargeable Li metal batteries. However, the optimum doping-content of Mg in Li-Mg anode and the mechanism of the improved performance are not well understood. In this study, density functional theory (DFT) calculations are used to investigate the effect of Mg amount in Li-Mg anode. The Li-Mg with about 5 wt. % Mg (abbreviated as Li-Mg5) has the lowest absorption energy of Li, thus all the surface area can be “controlled” by Mg atoms, leading to the smooth and continuous deposition of Li on the surface around the Mg center. A localized high concentration electrolyte enables Li-Mg5 to exhibit the best cycling stability in Li metal batteries with high-loading cathode and lean electrolyte under 4.4 V high-voltage, which is approaching the demand of practical application. This electrolyte also helps generate an inorganic-rich solid electrolyte interphase, which leads to smooth, compact and less corrosion layer on the Li-Mg5 surface. Both theoretical simulations and experimental results prove that Li-Mg5 has optimum Mg content and gives best battery cycling performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗