Search NASA⌕ Search

SEARCH · Search NASA

Results for “Carbon structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Growth and passivation of individual carbon nanoparticles by C2H2 addition at high temperatures: Dependence of growth rate and evolution on material and size

Absolute kinetics for reactions of C2H2 with a series of ∼60 individual carbon nanoparticles (NPs) from graphite, graphene, graphene oxide, carbon black, diamond, and nano-onion feedstocks were measured for temperatures (TNP) ranging from 1200 to 1700 K. All the NPs were observed to gain mass by carbon addition under conditions that varied with feedstock but with large variations in initial growth rate. Long reaction periods were studied to allow the evolution of growth rates over time to be observed. Diamond NPs were found to passivate against C2H2 addition if heated above ∼1400 K, and the highly variable initial reactivity for carbon nano-onions was found to depend on the presence of non-onion-structure surface carbon. For graphitic and carbon black NPs, three distinct growth modes were observed, correlated with the initial NP mass (Minitial). Smallest graphitic and carbon black NPs, with masses <∼25 MDa, initially grew rapidly but also passivated quickly after adding <4% of Minitial. NPs in the 20–50 MDa range also passivated but only after multiple waves of fast growth separated by periods of low reactivity, with up to ∼11% total mass gain before passivation. The largest carbon black and graphitic NPs, with Minitial >50 MDa, grew rapidly and continuously, adding up to ∼300% of Minitial with no sign of rate slowing as long as C2H2 was present. The efficiencies for C2H2 addition and etching by O2 are strongly correlated, but the correlation changes as the NPs passivate. Growth and passivation mechanisms are discussed.

Chemistry↗
DOE OSTI2020

Electrical and structural characterization of nano-carbon–aluminum composites fabricated by electro-charging-assisted process

Incorporating nano-carbon phases into metal-matrix composites is a promising strategy for simultaneously enhancing electrical conductivity and mechanical properties of metals. Here, we describe the manufacture of novel nano-carbonaluminum composites by an electro-charge-assisted process (EAP) that show 5.6% ± 1.7% increase in electrical conductivity compared to the base metal alloy. The source of nano-carbon that we used in this study is activated carbon with particle size less than 100 nm. The enhancement is attributed to nano-graphitic structures that extend through the lattice of the metal. Through electron transfer from the metal to the nanostructures the electron density at the interface of nano-crystalline graphite and the metal lattice increases thereby enhancing the bulk electrical conductivity. We identify the important fabrication parameters of the EAP for a reaction system employing a tapered graphite cathode. Here, a high current density of 100 A/cm 2 causes ionization and crystallization of the carbon in the liquid metal. The increase in electrical conductivity of the composite are directly related to the incorporation of the nanocrystalline carbon in the metal lattice. The superior performance of these nano-carbon aluminum composites makes them promising candidates for power transmission lines and other applications.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Nanoscale oxidation behavior of carbon fibers revealed with in situ gas cell STEM

Thermal protection systems are used to protect spacecraft payloads during the extreme conditions of atmospheric entry. The backbone of the composite material often used for NASA mission is carbon fiber, which oxidizes at these conditions. This study presents the direct observation of carbon oxidation using in situ Scanning Transmission Electron Microscopy (STEM). A thin section of a commercially-available carbon fiber material containing multiple structures was examined by STEM in a closed-environmental cell in which temperature was raised from 25 to 1050 °C under a steady flow of air. Results show that the random polycrystalline carbon structure oxidized more uniformly and rapidly than the single crystallite region, which oxidized more anisotropically. These findings are the first to directly observe the structural dependence of carbon oxidation rates at these length-scales while also giving important insight into the onset of pitting at various active surface sites, important pieces in fundamentally understanding of carbon oxidation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Improving Carbonate-Promoted C–H Carboxylation Using Mesoporous Carbon Supports

C–H carboxylation is an attractive way to utilize CO 2 for chemical production provided that it does not consume resource-intensive reagents. Alkali carbonates dispersed into the pores of mesoporous supports display strongly basic reactivity under CO 2 , allowing them to be used as base promoters for C–H carboxylation of (hetero)arenes in the absence of other reagents or catalysts. Mesoporous oxides are convenient support materials, but only a relatively small fraction of the dispersed carbonate (ca. 10-20%) is converted to carboxylate products when metal oxide supports are used. Here we compare mesoporous oxide and carbon supports and investigate the dependence of carbonate reactivity on pore structure. We show that using mesoporous carbons supports can increase the carbonate conversion by 2–4x when compared to oxide supports. This improved carbonate reactivity is maintained across a variety of mesoporous carbons with different pore structures (ordered vs. disordered) and pore diameters, indicating that the dispersed carbonate is intrinsically more reactive on the surface of a carbon material compared to an oxide surface. Reaction of the carboxylate products with dimethyl carbonate yields isolable methyl esters as the final product and regenerates the dispersed carbonate. We show that mesoporous carbon supports are robust to at least 5 cycles of successive C–H carboxylation and methylation with dimethyl carbonate. Furthermore, understanding how the support structure affects dispersed carbonate reactivity is valuable for advancing C–H carboxylation toward practical application and utilizing these materials in other CO 2 transformations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

3D‐Printed Carbon Nanoneedle Electrodes for Dopamine Detection in Drosophila

In vivo electrochemistry in small brain regions or synapses requires nanoelectrodes with long straight tips for submicron scale measurements. Nanoelectrodes can be fabricated using a Nanoscribe two-photon printer, but annealed tips curl if they are long and thin. We propose a new pulling-force strategy to fabricate a straight carbon nanoneedle structure. A micron-width bridge is printed between two blocks. The annealed structure shrinks during pyrolysis, and the blocks create a pulling force to form a long, thin, and straight carbon bridge. Parameterization study and COMSOL modeling indicate changes in the block size, bridge size and length affect the pulling force and bridge shrinkage. Electrodes were printed on niobium wires, insulated with aluminum oxide, and the bridge cut with focused ion beam (FIB) to expose the nanoneedle tip. Annealed needle diameters ranged from 400 nm to 5.25 μm and length varied from 50.5 μm to 146 μm. The electrochemical properties are similar to glassy carbon, with good performance for dopamine detection with fast-scan cyclic voltammetry. Nanoelectrodes enable biological applications, such as dopamine detection in a specific Drosophila brain region. Long and thin nanoneedles are generally useful for other applications such as cellular sensing, drug delivery, or gas sensing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Structure–Property Correlation of Hierarchically Porous Carbons for Fluorocarbon Adsorption

Although traditional commercially available porous carbon-fluorocarbon working pairs have shown promising applicability for adsorption cooling, advancements in synthetic carbons may further improve performance. Moreover, insights into structure-property relationships that target higher sorption capacities within these synthesized carbons may guide such materials' future design. We utilized hierarchically porous synthetic carbons (HPCs) with colossal microporous and mesoporous characterized by high surface areas (up to 2689 m 2 /g) and pore volumes (up to 10.31 cm 3 /g) towards fluorocarbon R134a adsorption. This unique pore topology leads to exceptional R134a uptake, ~250 wt.%, outperforming the highest uptake carbon material to date, Maxsorb III (~220 wt.%). Additionally, material characterizations reveal that the outstanding R134a capacity may be attributed to textural properties and oxygen-terminated functional groups more than graphitization of the material. Most importantly, HPCs are efficiently utilized in a two-bed model chiller device, where the performance shows excellent working capacity (105 wt%, ~1.5 times the value of reported carbon materials/R134a). Fluorocarbons adsorption on HPCs also displays fast kinetics (equilibrium time: ~2 min) mainly driven by physical adsorption (Qst: ~27 kJ/mol), characteristic of swiftly reversible behavior adsorption-desorption behaviors. This work provides a fundamental understanding of the applicability of HPCs/R134a working pair for adsorption cooling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Impact of Interfacial Structure on Heterogeneous Nucleation of Amorphous Carbonates

For this work, classical molecular dynamics simulations were performed to provide physical insight into the impact of interfacial structure on the heterogeneous nucleation of amorphous calcium carbonate (ACC, CaCO 3 ·H 2 O) and amorphous magnesium carbonate (AMC, MgCO 3 ·H 2 O) by using α-quartz as a model substrate. Interfacial structure and energies were computed for ACC and AMC in contact with the (100), (001), and (101) α-quartz surfaces. The simulations showed α-quartz surfaces drew water molecules out of the carbonate nuclei to form a partial hydration layer. The formation of a partial hydration layer and its disruption to the ACC/AMC structure meant the α-quartz–ACC/AMC interfaces were not energetically favored relative to separate α-quartz–water and ACC/AMC–water interfaces and, thus, homogeneous ACC/AMC nucleation was favored over heterogeneous nucleation. The CMD simulations hence provided an atomic-level explanation for a reported nonclassical growth mechanism whereby carbonate minerals grow via homogeneous nucleation and subsequent surface attachment of amorphous intermediates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Metallic and ferromagnetic carbon allotrope discovered using molecular precursors

Although carbon materials are known for their versatile structures and properties, a crystalline phase of carbon being both metallic and ferromagnetic is yet to be found. Here, using an organic molecular precursor 3,3-dimethyl-1-butene ( C 6 H 12 ) and a comprehensive theoretical study, we have discovered a metastable crystalline carbon phase that is both metallic and ferromagnetic under ambient conditions. The new carbon structures, produced by stacking puckered layers of 4,6-membered rings, are found to exhibit exotic electronic, magnetic, and mechanical properties originating from a special s p 2 − s p 3 bonding topology. These findings open the prospect of realizing the metallic and ferromagnetic carbon allotrope in practice. Published by the American Physical Society 2025

Fang, Hong (ORCID:0000000209688687)↗
DOE OSTI2021

Energetics of polymeric carbon monoxide

The transformation of carbon monoxide (CO) from a molecular liquid to a polymeric solid under isothermal compression at room temperature is investigated using first principles theory. We report structural and thermodynamic properties from ambient density up to 2.45 g/cc obtained using density functional theory molecular dynamics simulations, including hybrid exchange corrections. The theoretical results are compared with newly obtained polymeric CO samples, synthesized in a large volume press. The explosive performance of polymeric CO is predicted and discussed. Under most favorable assumptions, it is found to be comparable to trinitrotoluene.

25 ENERGY STORAGE↗
DOE OSTI2023

Ab initio structural dynamics of pure and nitrogen-containing amorphous carbon

Abstract Amorphous carbon (a-C) has attracted considerable interest due to its desirable properties, which are strongly dependent on its structure, density and impurities. Using ab initio molecular dynamics simulations we show that the sp 2 /sp 3 content and underlying structural order of a-C produced via liquid quenching evolve at high temperatures and pressures on sub-nanosecond timescales. Graphite-like densities ( $$\lesssim$$ ≲ 2.7 g/cc) favor the formation of layered arrangements characterized by sp 2 disordered bonding resembling recently synthesized monolayer amorphous carbon (MAC), while at diamond-like densities ( $$\gtrsim$$ ≳ 3.3 g/cc) the resulting structures are dominated by disordered tetrahedral sp 3 hybridization typical of diamond-like amorphous carbon (DLC). At intermediate densities the system is a highly compressible mixture of coexisting sp 2 and sp 3 regions that continue to segregate over 10’s of picoseconds. The addition of nitrogen (20.3%) (a-CN) generates major system features similar with those of a-C, but has the unexpected effect of reinforcing the thermodynamically disfavored carbon structural motifs at low and high densities, while inhibiting phase separation in the intermediate region. At the same time, no nitrogen elimination from the carbon framework is observed above $$\simeq$$ ≃ 2.8 g/cc, suggesting that nitrogen impurities are likely to remain embedded in the carbon structures during fast temperature quenches at high pressures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Molecular simulation using transfer-learned potentials for the disordered nanoscale structure of nitrogen-doped nanoporous carbons

Machine learning (ML)-based molecular dynamics (MD) simulations of the formation of a class of N-doped nanoporous carbons are performed to assess their disordered partially graphitized nanoscale structure. The study is motivated by the effectiveness of so-called nitrogen assembly carbons (NACs) for catalysis applications. Benchmark simulations for pure-C disordered graphitic systems reveal the importance of reliably capturing the vdW component of the potentials in order to accurately describe the tendency for layering of disordered graphene-like sheets. In our modeling, this is achieved by a transfer learning strategy incorporating features of the energetics from the optB88-vdW DFT functional into potentials initially trained with a less expensive functional, thereby providing a superior description of the pure-C systems. Generation from MD simulations of realistic partially graphitized structures is significantly more challenging for N-doped versus for pure C systems. However, such structures are achieved by a tailored MD simulation protocol mimicking the experimental synthesis process and in particular incorporating an annealing and subsequent quenching stages. Simulated PXRD patterns effectively reproduce the features of experimental observations for NACs, including the appearance of a prominent but broad (002) peak at around 25, and the development of another weaker feature associated with in-layer ordering of mixed C-N graphene-like sheets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

IACMI Project 4.7: Pultruded Textile Carbon Fiber for Spar Caps (Final Report)

The primary objective of this project was to demonstrate the potential to significantly reduce the cost of wind turbine blades with carbon fiber reinforced polymer (CFRP) structure. Applicability of textile carbon fibers (TCF) were evaluated for use in pultruded spar cap (SC) elements as a path to cost reduction for utility scale wind turbine blades. In earlier work for the Department of Energy (DOE) Wind Energy Technologies Office (WETO), a collaboration of Sandia National Laboratory (SNL), Oak Ridge National Laboratory (ORNL), and Montana State University has demonstrated potential for pultruded TCF to compete with infused fiberglass and commercially available carbon fiber pultruded sections for spar cap construction. In the design cases evaluated, the TCF sections fared well when compared on cost per unit composite stiffness and cost per unit composite compressive strength for those designs [1]. Both stiffness and compressive strength tend to be key factors in the design of blade composite Spar Cap which carry the bulk of the blade structural loads in bending. Spar Cap design tends to distribute largely symmetric tensile and compressive stresses to opposite sides of the spar structure, but since carbon fiber composite compressive strength is typically 20-50% lower than tensile strength, the compressive loading reaches failure levels well before the tensile loading. Stiffness is critical in containing the large tip deflection in high wind loading situations. However, materials and process development were very limited in the earlier study and the work in this project was expanded to make the comparative information more representative of what will be required in order to make further inroads towards implementation. Similar to that study, this project team confirmed that the primary materials of interest for pultruded spar cap elements should be thermoset (TS) resins reinforced by carbon fibers, utilizing as high a percentage of TCF as practical to benchmark cost and performance against commercial carbon fibers. To make the closest comparison possible and eliminate specific test article size, resin selection, and equipment/operational nuance effects, the team planned to pultrude sections with 100% commercially available carbon fiber (Panex 35 carbon fiber from Zoltek) as well as samples utilizing high fractions of TCF. The resin system chosen was based on formulations recommended by large wind industry supplier Hexion and consisted of Hexion resin RSL-4597, curing agent CCA-138, and internal mold release additive 117, along with common kaolin filler ASP400P from BASF. As commonly deployed in spar cap configurations, the team had a mold built to pultrude a rectangular spar cap element of 100mm width and 3mm thickness. The extremely limited number of samples produced for the earlier study were produced with a “generic” epoxy utilized for a variety of applications by the pultruder contracted to produce test articles for demonstration purposes. More importantly, those samples were produced at a fiber fraction only slightly over 50%. Based on feedback from our industrial advisory team for that project and strongly recommended by this project team, the consensus is that it is highly desirable to obtain fiber fractions of 65-68% for significant penetration in wind blade spar cap. Although this requirement has yet to be exhaustively confirmed in readily available information, this was established as a project goal and informally decided we needed to exceed 60% fiber fraction to gain serious industry consideration. Previous TCF pultrusion trials have been challenged by the lack of robust TCF packages, resulting in non-uniform tension across and between tows, as well as excess labor and waste for removal of interleaved paper. The non-uniform tension and associated intermingling of tows in textile acrylic fiber tows and associated difficulties created from broken filaments in carbon fiber conversion inhibit the ordered packing necessary to enhance fiber fraction elevation. (These “cross-overs” are not considered undesirable for textile applications and there is some sense that they might be advantageous for those applications). In addition to work that is ongoing at the acrylic fiber manufacturers to improve their formats, The Institute of Advanced Composites Manufacturing Innovation (IACMI) Project 6.12 (report PA16-0349-6.12-01) [2] has developed and demonstrated a more robust packaging and creeling approach that at least partially addresses these issues, thus improving control of the TCF feed into the pultrusion unit. It was hoped that these and other improvements currently being implemented would allow us to achieve fiber fractions at least approaching these fiber fraction targets. During this project, sections utilizing 100% commercially available carbon fiber reinforcement were produced as a baseline, as well as sections reinforced with about 94% TCF and the balance being commercially available fiber for comparison. The most important finding was that similar to results reported in the earlier WETO-funded project and results from tests of TCF reported at IACMI meetings, this work demonstrated that sections pultruded with TCF in an epoxy resin frequently utilized in actual spar cap production had stiffness and compressive strengths largely comparable to similar sections pultruded with a commercially available carbon fiber also frequently utilized in the wind industry. Although the amount of that data is limited, some of the tensile strength results were actually closer than would have been expected based on fiber strength results provided by the TCF and commercial fiber producers. The actual test data are reported and discussed in detail in Section 5. The pultruded sections dominated by TCF reinforcement were approximately 8-10% lower in fiber fraction than for the sections produced using commercial fiber alone, making direct comparison difficult. The COVID-19 project has provided significant insight into the current state-of-the-art with various TCF product forms. The data obtained in this project will guide the planned improvements at the precursor level, especially in attaining uniform tensioning and payout to facilitate enhanced fiber fractions and overall processability of the TCF composites. The project team is providing guidance to stakeholders concerning the attributes, needs, and potential demand for TCF in wind blade spar caps. Results achieved in this project are consistent with findings in the related work cited [1] and support this guidance and the high potential for this product type. TCF precursor-producing partners continue to express interest in enhancing their product forms and the team looks forward to working with these improved materials as they become available.

42 ENGINEERING↗
DOE OSTI2025

Low-dimensional carbon materials decorated FAPbI 3 for carbon-based perovskite solar cells

Carbon nanomaterials are at the forefront of research in perovskite solar cells (PSCs) due to their exceptional electrical, optical, and stability properties. Their diverse applications include serving as interfacial layers, additives, hole and electron transport materials, and back electrodes. While the influence of various low-dimensional carbon nanomaterial structures on crystallinity, optical and electrical performance, and overall device efficiency has been a topic of interest, it has not been thoroughly explored until now. In this study, we effectively integrated carbon quantum dots (CQDs), multi-walled carbon nanotubes (MWCNTs), and graphene into the FAPbI 3 photoactive layer using a two-step sequential deposition method. Our experiments revealed marked improvements in the photovoltaic performance of PSCs that incorporated all three types of carbon nanomaterials. In particular, the data shows significant enhancements in power conversion efficiency, demonstrating the effectiveness of these materials in optimizing device functionality. Notably, MWCNTs distinguished themselves by exhibiting a remarkable potential for enhancing long-term stability. This finding underscores the importance of selecting the right carbon nanomaterials for future PSC developments, paving the way for more reliable and efficient solar energy solutions. As a result, our research highlights the critical role of carbon nanomaterials in advancing perovskite solar technology.

14 SOLAR ENERGY↗
DOE OSTI2022

Computational investigation of hydrogen-induced phonon changes in carbon fiber

Optical vibrational spectroscopy has shown promise as a noninvasive means of monitoring the mechanical properties of carbon fiber (CF), which is increasingly used for industrial and consumer purposes. However, interpretation of optical vibrational spectra for solid materials is inferential, particularly when defects are present. Because inelastic neutron scattering (INS) spectroscopy is not subject to selection rules, the full vibrational spectra can be measured. And, identifying correlations between INS features and tensile properties can assist in the interpretation of spectra from more commonly used optical vibrational spectroscopic techniques, such as Raman and infrared (IR) spectroscopy. Recent INS experiments on high-performance commercial carbon fibers showed features near 900 and 1100 cm –1 in addition to a broad feature near 3000 cm –1 that increased in intensity with decreasing tensile strength. These features were assigned to hydrogen defects. Here, we use density functional theory to simulate the INS spectra of several hydrogen defect geometries in graphite as a model for carbon fiber structure units, confirming the experimental assignment of these peaks to hydrogen modes and providing insights into the structure and lattice dynamics of the defects.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-Resolution X-ray Spectromicroscopy Reveals Process-Structure Correlations in sub-5-μm Diameter Carbon Nanotube-Polymer Composite Dry-Spun Yarns

A persistent lack of detailed and quantitative structural analysis of these hierarchical carbon nanotube (CNT) ensembles precludes establishing processing-structure-property relationships that are essential to enhance macroscale performance (e.g., in mechanical, electrical, thermal applications). Here, in this work, we use scanning transmission X-ray microscopy (STXM) to analyze the hierarchical, twisted morphology of dry-spun CNT yarns and their composites, quantifying key structural characteristics such as density, porosity, alignment, and polymer loading. As the yarn twist density increases (15,000 to 150,000 turns per meter), the yarn diameter decreased (4.4–1.4 μm) and density increased (0.55–1.26 g·cm –3 ), as intuitively expected. Yarn density, ρ, ubiquitously scaled with diameter d according to ρ ~ d –2 for all parameters studied here. Spectromicroscopy probes with 30 nm resolution and elemental specificity were employed to analyze the radial and longitudinal distribution of the oxygen-containing polymer content (~30% weight fraction), demonstrating nearly perfect filling of the voids between CNTs with a vapor-phase polymer coating and cross-linking process. These quantitative correlations highlight the intimate connections between processing conditions and yarn structure with important implications for translating the nanoscale properties of CNTs to the macroscale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Advanced Structured Adsorbent Architectures for Transformative Carbon Dioxide Capture Performance (Final Report)

Svante is a world leader at using solid sorbents for low-cost Carbon Dioxide (CO 2 ) capture, a technology which is recognized as critical in meeting the dual mandates of energy security/reliability and the mitigation of man-made CO 2 emissions. Svante has been developing proprietary adsorbent material compositions, forming them into structured laminates, developing and optimizing process cycles, and system design for efficient capture of CO 2 from post-combustion flue gases of thermal power plants and industrial facilities. The deployment of first-generation CO 2 capture technology has been significantly hampered by high costs and energy penalties, among other barriers. Second generation CO 2 capture technologies (including the Mark I variant of Svante’s Veloxotherm™ adsorption-based technology), utilizing single adsorbent architecture, show promise for reducing the barriers to deploying CO 2 capture plants in commercially meaningful numbers. The objective of this project was to evaluate the Recipient’s transformational (Mark-II) VeloxoTherm™ Technology via the development and bench-scale testing of an advanced structured adsorbent, including novel Bi-layer, laminated adsorbent structures and segmented beds. Svante selected, synthesized, and characterized tailored solid adsorbents for computational modeling, advanced structured adsorbent development, process simulations, and dynamic bench scale (~1-10 kg/day CO 2 captured) testing using an existing single-bed VeloxoTherm™ Station (VTS) coupled with a natural gas-fired boiler. Segmented beds used the in-house, multi-bed Process Demonstration Unit (PDU) to demonstrate key performance indicators (KPIs), such as recovery, product purity, regeneration energy, and the integrated system's productivity in lifetime analysis. Segmented beds were used at a 1 tonne per day (TPD) unit at an industrial site to provide bench-scale validation of performance in an industrial setting. Svante was developing and optimizing the post-combustion CO 2 adsorption technology architectures, including the Bi-layer and segmented laminated adsorbent structure design, integrated rapid cycle temperature swing adsorption (RC-TSA) cycle, flow path architecture, and adsorbent bed construction and packaging (including gas porting) to progress towards achievement of DOE’s Transformational CO 2 Capture goals of 95% CO 2 purity and a cost of electricity at least 30% lower than a supercritical Pulverized Coal (PC) power plant with CO 2 capture, or approximately $30 per tonne of CO 2 captured ready for demonstration by 2030. The main requirements to reach the DOE target cost of carbon capture below $30/MT using Rapid-Cycling Temperature Swing Adsorption (RC-TSA) are as follows: (1) Increased capacity at different CO 2 concentrations, (2) Increased sorbents cycle life, (3) Increased O 2 resistance, and (4) Decreased steam requirement to extract 1 kg of CO 2 .

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Tailored Additive Design of Scaffold‐Free Porous Mg for Ultimate Hydrogen Storage

For hydrogen storage materials to become practically viable, comprehensive improvements in key properties—kinetics, thermodynamics, thermal transport, and durability—are crucial. Porous Mg structure has been proposed as a promising strategy due to its high storage capacity and ability to accommodate volume expansion. However, challenges such as sluggish kinetics and structural degradation resulting from instability due to vacant sites still remain. In this study, a tailored design of porous Mg structure with site-specific transition metal dual-doping and structure-reinforced carbon nanotube (CNT)-framework is presented for optimal hydrogen storage. Ti and Ni are strategically deposited on the surface to synergistically enhance hydrogen sorption kinetics by facilitating hydrogen dissociation and diffusion, while CNTs are interpenetrated into 3D Mg structure for improving thermal conductivity and maintaining the porous structure. The resulting composite demonstrates exceptional performance, achieving hydrogen absorption and desorption of 4.8 and 5.8 wt%, respectively, within 10 min with an impressively low activation energy for absorption of 46 kJ mol −1 H 2 . Even after 50 cycles, its capacity and porous structure are well preserved, showing excellent cyclability in comparison with previously reported materials. In conclusion, this delicate design strategy based on a comprehensive understanding of structural and chemical characteristics is key to maximizing the targeted performance.

CNT embedding↗
DOE OSTI2021

Sustainable Coal Tar Pitch Carbon Fiber Manufacturing

Coal is a versatile resource that has historically propelled the Industrial Revolution, transportation, and energy generation, and continues to meet needs for power. The United States possesses the largest worldwide coal reserves (with a 2019 total production-to-recoverable-reserves ratio of 0.05) that are of high quality and are cost-effective to recover (i.e., $0.03/kg–$0.10/kg). However, the demand of coal for power generation has declined because of a shift to natural gas (because of lower natural gas prices) and to renewable energy sources. This decline has affected the economic viability US coal industry. Historically, domestic demand for coal was driven mostly by the electric power sector, which accounts for about 93% of the total demand, followed by industrial uses (primarily for cement and chemicals at a minimal level) and steel production (coke). The complex, dense carbon chemical structure of coal, abundant domestic supply, and stable, low price gives it great potential for use in a wide range of value-added non-fuel coal products (e.g., nanomaterials at $20,000/kg–$100,000/kg and commercial-grade carbon fiber at $22/kg–$33/kg), as well as in upgraded coal fuels.

01 COAL, LIGNITE, AND PEAT↗