Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ceramic Capacitor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

The relationship between reliability and bonding techniques in hybrid systems

Differential thermal expansion has been shown to be responsible for many observed failures in ceramic chip capacitors mounted on alumina substrates. The present work has shown that the mounting techniques used in bonding the capacitors have a marked effect upon the thermally induced mechanical stress and thus the failure rate. A mathematical analysis of a composite model of the capacitor-substrate system to predict the magnitude of thermally induced stresses has been conducted. It has been observed that the stresses in more compliant bonding systems such as soft lead/tin and indium solders are significantly lower than those in hard solder and epoxy systems. The marked dependence upon heating and cooling rate has proven to be a determining factor in the prediction of failure in both the indium and tin/lead solder systems. This study has shown that the harder or higher melting solders are less susceptible to thermal cycling effects but that they are more likely to fail during initial processing operations. Recommendations are made concerning the optimum bonding system for the achievement of maximum reliability.

Kinser, D. L.↗

Partial discharge testing under direct voltage conditions

DC partial discharge (PD) (corona) testing is performed using a multichannel analyzer for pulse storing, and data is collected during increase of voltage and at quiescent voltage levels. Thus high voltage ceramic disk capacitors were evaluated by obtaining PD data interspersed during an accelerated life test. Increased PD activity was found early in samples that later failed catastrophically. By this technique, trends of insulation behavior are revealed sensitively and nondestructively in high voltage dc components.

Bever, R. S.↗

Aqueous synthesis and electrical properties of nano-crystalline PLZT capacitors.

Devices with nano-crystalline microstructures have been shown to possess improved electrical properties. Further advantages include lower processing temperatures; however, device fabrication from nano-particles poses several challenges. This presentation describes a novel aqueous synthesis technique to produce large batch sizes with minimal waste. The precipitate is readily converted at less than 550 C to a phase pure, nano-crystalline Pb{sub 0.88} La{sub 0.12}(Zr{sub 0.70} Ti{sub 0.30}){sub 0.97} O{sub 3} powder. Complications and solutions to sample fabrication from nano-powders are discussed, including the use of glass sintering aids to improve density and further lower sintering temperatures. Finally, electrical properties are presented to demonstrate the potential benefits of nano-crystalline capacitors.

36 MATERIALS SCIENCE↗

Origin(s) of the apparent high permittivity in CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics: clarification on the contributions from internal barrier layer capacitor and sample-electrode contact effects

CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics with a range of resistivities have been prepared using both conventional sintering and spark plasma sintering. For all cases, the high effective permittivity is associated primarily with an internal barrier layer capacitor mechanism. Additional polarization associated with the electrode-sample interface may appear but its visibility depends on the grain boundary resistivity (R{sub gb}) of the ceramic. If the R{sub gb} is large, the electrode polarization is obscured by sample-related effects; if the R{sub gb} is small, a separate impedance associated with the electrode polarization may be seen. Discrepancies in the literature regarding the magnitude and origin of the high effective permittivity are attributed to a combination of differences in processing conditions, electrode contact material and measuring frequency range.

36 MATERIALS SCIENCE↗

Uses of ceramics in microelectronics: A survey

The properties and behavior of ceramic materials used in components for electronic circuitry are examined to appraise the present and future directions for microelectronics, and to suggest further product development, and how innovations may be useful in other technologies. Ceramic and glass insulators, resistors, capacitors, and the use of ceramics and glasses in microcircuitry are discussed along with technology transfer to nonaerospace uses.

Bratschun, W. R.↗

Reliability Effects of Surge Current Testing of Solid Tantalum Capacitors

Solid tantalum capacitors are widely used in space applications to filter low-frequency ripple currents in power supply circuits and stabilize DC voltages in the system. Tantalum capacitors manufactured per military specifications (MIL-PRF-55365) are established reliability components and have less than 0.001% of failures per 1000 hours (the failure rate is less than 10 FIT) for grades D or S, thus positioning these parts among electronic components with the highest reliability characteristics. Still, failures of tantalum capacitors do happen and when it occurs it might have catastrophic consequences for the system. This is due to a short-circuit failure mode, which might be damaging to a power supply, and also to the capability of tantalum capacitors with manganese cathodes to self-ignite when a failure occurs in low-impedance applications. During such a failure, a substantial amount of energy is released by exothermic reaction of the tantalum pellet with oxygen generated by the overheated manganese oxide cathode, resulting not only in destruction of the part, but also in damage of the board and surrounding components. A specific feature of tantalum capacitors, compared to ceramic parts, is a relatively large value of capacitance, which in contemporary low-size chip capacitors reaches dozens and hundreds of microfarads. This might result in so-called surge current or turn-on failures in the parts when the board is first powered up. Such a failure, which is considered as the most prevalent type of failures in tantalum capacitors [I], is due to fast changes of the voltage in the circuit, dV/dt, producing high surge current spikes, I(sub sp) = Cx(dV/dt), when current in the circuit is unrestricted. These spikes can reach hundreds of amperes and cause catastrophic failures in the system. The mechanism of surge current failures has not been understood completely yet, and different hypotheses were discussed in relevant literature. These include a sustained scintillation breakdown model [1-3]; electrical oscillations in circuits with a relatively high inductance [4-6]; local overheating of the cathode [5,7, 8]; mechanical damage to tantalum pentoxide dielectric caused by the impact of MnO2 crystals [2,9, 10]; or stress-induced-generation of electron traps caused by electromagnetic forces developed during current spikes [11]. A commonly accepted explanation of the surge current failures is that at unlimited current supply during surge current conditions, the self-healing mechanism in tantalum capacitors does not work, and what would be a minor scintillation spike if the current were limited, becomes a catastrophic failure of the part [l, 12]. However, our data show that the scintillation breakdown voltages are significantly greater that the surge current breakdown voltages, so it is still not clear why the part, which has no scintillations, would fail at the same voltage during surge current testing (SCT).

Teverovsky, Alexander↗

All-Ceramic Passive Wireless Temperature Sensor Realized by Tin-Doped Indium Oxide (ITO) Electrodes for Harsh Environment Applications

In this work, an all-ceramic passive wireless inductor–capacitor (LC) resonator was presented for stable temperature sensing up to 1200 °C in air. Instead of using conventional metallic electrodes, the LC resonators are modeled and fabricated with thermally stable and highly electroconductive ceramic oxide. The LC resonator was modeled in ANSYS HFSS to operate in a low-frequency region (50 MHz) within 50 × 50 mm geometry using the actual material properties of the circuit elements. The LC resonator was composed of a parallel plate capacitor coupled with a planar inductor deposited on an Al2O3 substrate using screen-printing, and the ceramic pattern was sintered at 1250 °C for 4 h in an ambient atmosphere. The sensitivity (average change in resonant frequency with respect to temperature) from 200–1200 °C was ~170 kHz/°C. The temperature-dependent electrical conductivity of the tin-doped indium oxide (ITO, 10% SnO2 doping) on the quality factor showed an increase of Qf from 36 to 43 between 200 °C and 1200 °C. The proposed ITO electrodes displayed improved sensitivity and quality factor at elevated temperatures, proving them to be an excellent candidate for temperature sensing in harsh environments. The microstructural analysis of the co-sintered LC resonator was performed using a scanning electron microscope (SEM) which showed that there are no cross-sectional and topographical defects after several thermal treatments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Energy Density Capacitors for Electric Vehicle Traction Inverters

DC bus capacitors take up substantial space in a traction inverter, limiting the traction drive power density. Thus, several commercial capacitor technologies, under consideration for use as DC bus capacitors for electric vehicle traction inverters, were reviewed for their ability to optimize the volume of traction inverters and are evaluated in this paper. Three promising capacitor technologies--film, ceramic, and PLZT have been selected for detailed experimental characterization. Experimental results for equivalent series resistance, equivalent series inductance, and effective capacitance with respect to DC bias voltage for various operating frequencies and temperatures are presented. The results reveal the superiority of the PLZT capacitor in terms of power density, current conduction capability, and redundancy.

Chowdhury, Shajjad↗

Preparation and characterization of Ag-doped BaTiO{sub 3} based X7R ceramics

Ag-doped BaTiO{sub 3} based X7R (temperature coefficient of capacitance within the range of {+-}15% between -55 and +125 deg. C) ceramics with different amounts of silver (0.0-20.0 mol%) were prepared in this paper. The X-ray diffraction analysis indicated that no phases other than BaTiO{sub 3} and silver were observed in the ceramics. The energy dispersive X-ray spectroscopy analysis showed that the silver particles presented homogeneous distribution in the BaTiO{sub 3} ceramics. The dielectric properties of Ag-doped ceramics were investigated. A small amount of silver (<0.5 mol%) and a large amount of silver (>2.0 mol%) could both improve the sintered density and permittivity, but more content of silver (0.5-2.0 mol%) would decrease the relative density and permittivity. Specially, the temperature coefficient of capacitors of the ceramics doped with 20 mol% silver still met the X7R characteristics, and the room temperature permittivity of the ceramics was 6823, which was the highest dielectric constant in the BaTiO{sub 3} based X7R ceramics.

36 MATERIALS SCIENCE↗

300°C Capable Electronics Platform and Temperature Sensor System For Enhanced Geothermal Systems (Final Technical Report)

A silicon carbide (SiC) based electronic temperature sensor prototype has been demonstrated to operate at 300°C. We showed continuous operation of 1,000 hours with SiC operational amplifier and surface mounted discreet resistors and capacitors on a ceramic circuit board. This feasibility demonstration is a major milestone in the development of high temperature electronics in general and high temperature geothermal exploration and well management tools in particular. SiC technology offers technical advantages that are not found in competing technologies such as silicon-on-insulator (SOI) at high temperatures of 200°C to 300°C and beyond. The SiC integrated circuits and packaging methods can be used in new product introduction by GE Oil and Gas for high temperature down-hole tools. The existing SiC fabrication facility at GE is sufficient to support the quantities currently demanded by the marketplace, and there are other entities in the United States and other countries capable of ramping up SiC technology manufacturing. The ceramic circuit boards are different from traditional organic-based electronics circuit boards, but the fabrication process is compatible with existing ceramic substrate manufacturing. This project has brought high temperature electronics forward, and brings us closer to commercializing tools that will enable and reduce the cost of enhanced geothermal technology to benefit the public in terms of providing clean renewable energy at lower costs.

15 GEOTHERMAL ENERGY↗

High-Temperature Passive Power Electronics

In many future NASA missions - such as deep-space exploration, the National AeroSpace Plane, minisatellites, integrated engine electronics, and ion or arcjet thrusters - high-power electrical components and systems must operate reliably and efficiently in high-temperature environments. The high-temperature power electronics program at the NASA Lewis Research Center focuses on dielectric and insulating material research, the development and characterization of high-temperature components, and the integration of the developed components into a demonstrable 200 C power system - such as an inverter. NASA Lewis has developed high-temperature power components through collaborative efforts with the Air Force Wright Laboratory, Northrop Grumman, and the University of Wisconsin. Ceramic and film capacitors, molypermalloy powder inductors, and a coaxially wound transformer were designed, developed, and evaluated for high-temperature operation.

Source record↗

Power Electronics Being Developed for Deep Space Cryogenic Applications

Electronic circuits and systems designed for deep space missions need to operate reliably and efficiently in harsh environments that include very low temperatures. Spacecraft that operate in such cold environments carry a large number of heaters so that the ambient temperature for the onboard electronics remains near 20 C. Electronics that can operate at cryogenic temperatures will simplify system design and reduce system size and weight by eliminating the heaters and their associated structures. As a result, system development and launch cost will be reduced. At the NASA Glenn Research Center, an ongoing program is focusing on the development of power electronics geared for deep space low-temperature environments. The research and development efforts include electrical components design, circuit design and construction, and system integration and demonstration at cryogenic temperatures. Investigations are being carried out on circuits and systems that are targeted for use in NASA missions where low temperatures will be encountered: devices such as ceramic and tantalum capacitors, metal film resistors, semiconductor switches, magnetics, and integrated circuits including dc/dc converters, operational amplifiers, voltage references, and motor controllers. Test activities cover a wide range of device and circuit performance under simple as well as complex test conditions, such as multistress and thermal cycling. The effect of low-temperature conditions on the switching characteristics of an advanced silicon-on-insulator field effect transistor is shown. For gate voltages (VGS) below 2.6 V, drain currents at -190 C are lower than drain currents at room temperature (20 C).

Patterson, Richard L.↗

Liquid-Metal-Fed Pulsed Plasma Thrusters

A short document proposes liquid-metal-fed pulsed plasma thrusters for small spacecraft. The propellant liquid for such a thruster would be a low-melting-temperature metal that would be stored molten in an unpressurized, heated reservoir and would be pumped to the thruster by a magnetohydrodynamic coupler. The liquid would enter the thruster via a metal tube inside an electrically insulating ceramic tube. A capacitor would be connected between the outlet of the metal tube and the outer electrode of the thruster. The pumping would cause a drop of liquid to form at the outlet, eventually growing large enough to make contact with the outer electrode. Contact would close the circuit through the capacitor, causing the capacitor to discharge through the drop. The capacitor would have been charged with enough energy that the discharge would vaporize, ionize, and electromagnetically accelerate the contents of the metal drop. The resulting plasma would be ejected at a speed of about 50 km/s. The vaporization of the drop would reopen the circuit through the capacitor, enabling recharging of the capacitor. As pumping continued, a new drop would grow and the process would repeat.

Markusic, Thomas↗

Impedance Spectroscopy Study of the Electrical Properties of Cation-Substituted Barium Hexaaluminate Ceramics

We report on the behavior of frequency and temperature dependences of the impedance of a measuring cell in the form of a parallel-plate capacitor filled with barium hexaaluminate ceramics with four aluminum cations replaced by iron (BaO · 2Fe{sub 2}O{sub 3} · 4Al{sub 2}O{sub 3}). The measurements have been performed in the frequency range of 0.5–10{sup 8} Hz at temperatures of 20-375°C. A technique for determining the electrical properties of the investigated ceramics is proposed, which is based on an equivalent electric circuit allowing the recorded impedance spectra to be approximated with sufficiently high accuracy. The established spectral features are indicative of the presence of two electric relaxation times different from each other by three orders of magnitude. This fact is explained by the difference between the charge transport processes in the bulk of crystallites and thin intercrystallite spacers, for which the charge activation energies have been determined.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Sputter deposition of thin film MIM capacitors on LTCC substrates for RF bypass and filtering applications

Thin film capacitors for RF bypass and filtering applications were sputter deposited onto low temperature co-fired ceramic (LTCC) substrates. The capacitors were configured in a metal-insulator-metal (MIM) design featuring 200 nm thick Al electrodes and a 300 nm thick Al{sub 2}O{sub 3} dielectric layer, with dimensions varied between ~150x150 μm and ~750x750 μm. DC current-voltage measurements (E ≤ 5 MV/cm) coupled with impedance analysis (≤15 MHz) was used to characterize the resulting devices. More than 90% of the devices functioned as capacitors with high DC resistance (>20 MΩ) and low loss (tan δ <0.1). A second set of capacitors were made under the same experimental conditions with device geometries optimized for high frequency (≥200 MHz) applications. These capacitors featured temperature coefficient of capacitance (TCC) values between 500 and 1000 ppm/°C as well as low loss and high self-resonant frequency performance (ESR <0.6 Ohms at self-resonance of 5.7 GHz for 82 pF). Capacitance and loss values were comparable between the capacitor structures of similar areas at the different frequency regimes.

36 MATERIALS SCIENCE↗