Search NASA⌕ Search

SEARCH · Search NASA

Results for “Combined effect testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Outbrief - Long Life Rocket Engine Panel

This white paper is an overview of the JANNAF Long Life Rocket Engine (LLRE) Panel results from the last several years of activity. The LLRE Panel has met over the last several years in order to develop an approach for the development of long life rocket engines. Membership for this panel was drawn from a diverse set of the groups currently working on rocket engines (Le. government labs, both large and small companies and university members). The LLRE Panel was formed in order to determine the best way to enable the design of rocket engine systems that have life capability greater than 500 cycles while meeting or exceeding current performance levels (Specific Impulse and Thrust/Weight) with a 1/1,OOO,OOO likelihood of vehicle loss due to rocket system failure. After several meetings and much independent work the panel reached a consensus opinion that the primary issues preventing LLRE are a lack of: physics based life prediction, combined loads prediction, understanding of material microphysics, cost effective system level testing. and the inclusion of fabrication process effects into physics based models. With the expected level of funding devoted to LLRE development, the panel recommended that fundamental research efforts focused on these five areas be emphasized.

Quinn, Jason Eugene↗
NASA NTRS1994

Self contamination effects in the TAUVEX UV Telescope: Ground testing and computer simulation

The contamination effects due to outgassing from construction materials of the TAUVEX (Tel Aviv University UV Telescope) were evaluated using a combination of ground testing and computer simulations. Tests were performed from the material level of the system level including: (1) High sensitivity CVCM(10(exp -3 percent) measurements of critical materials. (2) Optical degradation measurements of samples specially contaminated by outgassing products at different contamination levels. (3) FTIR studies of chemical composition of outgassed products on above samples. (4) High resolution AFM studies of surface morphology of contaminated surfaces. The expected degradation of TAUVEX performance in mission was evaluated applying a computer simulation code using input parameters determined experimentally in the above tests. The results have served as guidelines for the proper selection of materials, cleanliness requirements, determination of the thermal conditions of the system and bakeout processes.

Lifshitz, Y.↗
NASA NTRSDate not supplied

Expanding the Capability of A Legacy Combustion Flametube to Test High Temperature Engine Materials in Relevant Environments

New materials and component designs are needed to advance gas turbine engine technology and provide the performance and efficiency needs for future applications. In order to advance these materials, testing in combustion environments is a critical step prior to engine testing. In this work, we detail the design and the fabrication of a materials test sector in a flametube combustor facility. The facility simulates a combustion environment similar to that experienced by components in gas turbine engines. The flow regime is characterized by a combination of high-temperature, high-velocity, high-heat flux, and high-velocity that components experience in gas turbine engines. Exposure of components in this facility allows for the study of combined environmental effects and the impact on both coating and substrate durability. The test facility may operate across a wide range of pressures from 275-400 psig (1,896-2,758 kPa) and an air flow rate of 5 lb/s (2.27 kg/s). While combustion gas temperature is expected in excess of 3,000°F (1,649°C), 900°F (482°C) cooling air may be supplied to the backside of components or test articles. The flametube combustor was previously used to evaluate fuel injectors and combustion products, and the new test configuration will also allow for materials exposure to complex, engine-like conditions. The interior of the Test Section was additively manufactured from GRCop-84 and cryogenically fit and brazed to a stainless steel 304 housing. The use of a copper liner minimizes welds and with active cooling, is expected to provide better durability over traditional hardware using stainless steel or Inconel with a ceramic liner. The Test Section has two opposing removable windows approximately 230 mm x 80 mm that can accommodate articles up to 85 mm tall. This modular design allows for custom platforms to hold coupons, panels, or airfoil shapes to be tested with minimal re-engineering or fabrication. The bolted joint and sealing remains consistent, so any new testing only needs to work within the existing design footprint. This paper will provide an overview of the facility capabilities, design considerations, as well as thermal and structural analysis of the hardware. Future testing of ceramic matrix composite (CMC) airfoils and advanced environmental barrier coatings (EBCs) will also be discussed.

Combustion↗
NASA NTRSDate not supplied

Reynolds Number Effects on a 5.2%-Scale High Lift Common Research Model

A 5.2%-scale High Lift Common Research Model (CRM-HL) semispan wind tunnel model was tested at the National Transonic Facility (NTF) wind tunnel in Hampton, VA. One of the primary objectives of the NTF test was to determine the effect of varying Reynolds number on the configuration. The test used a combination of air and cryogenic nitrogen testing to obtain up to flight-like Reynolds numbers. The landing and takeoff configurations of the model were tested at speeds ranging from Mach 0.2 to 0.35. The Reynolds numbers based on the mean aerodynamic chord of the model ranged from 1.6 to 30 million. Overall, the lift increased and drag decreased with increasing Reynolds number for chord Reynolds numbers less than 16 million, following well-established trends. However, some anomalies in the force and moment data were observed in the linear region of the angle of attack range that did not follow expected trends. The force and moment results for both the landing and takeoff configurations are presented, along with surface pressure data for the landing configuration. Incremental effects from the landing gear, nacelle, and horizontal tail on the landing configuration are also presented.

CRM-HL↗
NASA NTRSDate not supplied

Reynolds Number Effects on a 5.2%-Scale High Lift Common Research Model

A 5.2%-scale High Lift Common Research Model (CRM-HL) semispan wind tunnel model was tested at the National Transonic Facility (NTF) wind tunnel in Hampton, VA. One of the primary objectives of the NTF test was to determine the effect of varying Reynolds number on the configuration. The test used a combination of air and cryogenic nitrogen testing to obtain up to flight-like Reynolds numbers. The landing and takeoff configurations of the model were tested at speeds ranging from Mach 0.2 to 0.35. The Reynolds numbers based on the mean aerodynamic chord of the model ranged from 1.6 to 30 million. Overall, the lift increased and drag decreased with increasing Reynolds number for chord Reynolds numbers less than 16 million, following well-established trends. However, some anomalies in the force and moment data were observed in the linear region of the angle of attack range that did not follow expected trends. The force and moment results for both the landing and takeoff configurations are presented, along with surface pressure data for the landing configuration. Incremental effects from the landing gear, nacelle, and horizontal tail on the landing configuration are also presented.

CRM-HL↗
DOE OSTI2022

Exploring Critical Synthetic Parameters for Nanoscale ε-Fe 2 O 3 and Their Influence on Magnetic Behaviors

An intermediate polymorph of iron oxide, ε-Fe 2 O 3 , has attracted significant attention due to its giant coercive field ( H c ) and potential applications in high-frequency millimeter-wave absorption and high-density magnetic recording. However, the fabrication of ε-Fe 2 O 3 with high phase purity is still a challenge due to complicated synthetic procedures and a large variety of reaction parameters. In this study, we have identified critical reaction parameters to improve the phase purity of ε-Fe 2 O 3 , and the effects of all possible reaction parameters have been tested through systematic studies. A combination of structural and magnetic characterization techniques provides us with an accurate and reliable phase purity analysis of the ε-Fe 2 O 3 phase. Specifically, we observed that (1) the reaction temperature and time and (2) the addition of Ba are critical parameters to improve the phase purity. We identified the optimal conditions that maximize the coercivity and phase purity, giving insight into the effects of each parameter on the γ- to ε- to α-phase-transition pathway. We obtained nearly single-phase ε-Fe 2 O 3 (~87 wt % with ~13 wt % α-phase) with a large coercivity of H c = 20.6 kOe, enabling us to obtain pure ε-Fe 2 O 3 by a simple magnetic separation protocol, and tuned the H c of the ε-Fe 2 O 3 nanoparticles in the range of 4.0–20.6 kOe by controlling the reaction parameters. Furthermore, the structural properties of the resulting ε-Fe 2 O 3 nanoparticles are confirmed by characterizing their chemical and magnetic properties using X-ray absorption spectroscopy and X-ray magnetic circular dichroism measurements.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Simulated Space Vacuum Ultraviolet (VUV) Exposure Testing for Polymer Films

Vacuum ultraviolet (VUV) radiation of wavelengths between 115 and 200 nm produced by the sun in the space environment can cause degradation to polymer films producing changes in optical, mechanical, and chemical properties. These effects are particularly important for thin polymer films being considered for ultra-lightweight space structures, because, for most polymers, VUV radiation is absorbed in a thin surface layer. NASA Glenn Research Center has developed facilities and methods for long-term ground testing of polymer films to evaluate space environmental VUV radiation effects. VUV exposure can also be used as part of sequential simulated space environmental exposures to determine combined damaging effects. This paper will describe the effects of VUV on polymer films and the necessity for ground testing. Testing practices used at Glenn Research Center for VUV exposure testing will be described including characterization of the VUV radiation source used, calibration procedures traceable to the National Institute of Standards and Technology (NIST), and testing techniques for VUV exposure of polymer surfaces.

Dever, Joyce A.↗
NASA NTRS2000

FDNS CFD Code Benchmark for RBCC Ejector Mode Operation: Continuing Toward Dual Rocket Effects

Computational Fluid Dynamics (CFD) analysis results are compared with benchmark quality test data from the Propulsion Engineering Research Center's (PERC) Rocket Based Combined Cycle (RBCC) experiments to verify fluid dynamic code and application procedures. RBCC engine flowpath development will rely on CFD applications to capture the multi -dimensional fluid dynamic interactions and to quantify their effect on the RBCC system performance. Therefore, the accuracy of these CFD codes must be determined through detailed comparisons with test data. The PERC experiments build upon the well-known 1968 rocket-ejector experiments of Odegaard and Stroup by employing advanced optical and laser based diagnostics to evaluate mixing and secondary combustion. The Finite Difference Navier Stokes (FDNS) code [2] was used to model the fluid dynamics of the PERC RBCC ejector mode configuration. Analyses were performed for the Diffusion and Afterburning (DAB) test conditions at the 200-psia thruster operation point, Results with and without downstream fuel injection are presented.

West, Jeff↗
NASA NTRS2016

Wind Tunnel Test of Subscale Ringsail and Disk-Gap-Band Parachutes

A subsonic wind tunnel test was conducted to determine the drag and static aerodynamic coefficients, as well as to capture the dynamic motions of a new Supersonic Ringsail parachute developed by the Low Density Supersonic Decelerator Project. To provide a comparison against current Mars parachute technology, the Mars Science Laboratory's Disk-Gap-Band parachute was also included in the test. To account for the effect of fabric permeability, two fabrics ("low" and "standard" permeability) were used to fabricate each parachute canopy type, creating four combinations of canopy type and fabric material. A wide range of test conditions were covered during the test, spanning Mach numbers from 0.09 to 0.5, and static pressures from 103 to 2116 pounds per square inch (psf) (nominal values). The fabric permeability is shown to have a first-order effect on the aerodynamic coefficients and dynamic motions of the parachutes. For example, for a given parachute type and test condition, models fabricated from "low" permeability fabric always have a larger drag coefficient than models fabricated from "standard" permeability material. This paper describes the test setup and conditions, how the results were analyzed, and presents and discusses a sample of the results. The data collected during this test is being used to create and improve parachute aerodynamic databases for use in flight dynamics simulations for missions to Mars.

Zumwalt, Carlie H.↗
NASA NTRS1957

Static Longitudinal and Lateral Stability Characteristics at Low Speed of 45 Degree Sweptback-midwing Models Having Wings with an Aspect Ratio of 2, 4, or 6

Results are presented of tests conducted in the Langley stability tunnel to determine the effects of various components and combinations of components on the static longitudinal and lateral stability characteristics at low speed of a series of 45 degree sweptback-midwing-airplane configurations having wings with an aspect ratio of 2, 4, or 6. The tests were made at a dynamic pressure of 24.9 pounds per square foot which corresponds to a Mach number of 0.13 and Reynolds numbers of 1.00 x 10(exp 6), 0.71 x 10 (exp 6), and 0.58 x 10 (exp 6) based on the respective wing mean aerodynamic chords. The angle-of-attack range covered was from -4 degrees to 32 degrees and the sideslip angles used for the lateral-derivative tests were 5 degrees and -5 degrees. An increasing loss in tail contribution to directional stability both with increasing wing aspect ratio and increasing angle of attack was found to be a principal cause of all the complete models becoming directionally unstable in the high angle-of-attack range.

STABILITY, LONGITUDINAL - STATIC↗
NASA NTRS2016

Capabilities of the Environmental Effects Branch at Marshall Space Flight Cente

The Environmental Effects Branch at the Marshall Space Flight Center supports a myriad array of programs for NASA, DoD, and commercial space including human exploration, advanced space propulsion, improving life on Earth, and the study of the Sun, the Earth, and the solar system. The branch provides testing, evaluation, and qualification of materials for use on external spacecraft surfaces and in contamination-sensitive systems. Space environment capabilities include charged particle radiation, ultraviolet radiation, atomic oxygen, impact, plasma, and thermal vacuum, anchored by flight experiments and analysis of returned space hardware. These environmental components can be combined for solar wind or planetary surface environment studies or to evaluate synergistic effects. The Impact Testing Facility allows simulation of impacts ranging from sand and rain to micrometeoroids and orbital debris in order to evaluate materials and components for flight and ground-based systems. The Contamination Control Team is involved in the evaluation of environmentally-friendly replacements for HCFC-225 for use in propulsion oxygen systems, developing cleaning methods for additively manufactured hardware, and reducing risk for the Space Launch System.

Rogers, Jan↗
NASA NTRS2004

Real-Time Measurements of Aft Dome Insulation Erosion on Space Shuttle Reusable Solid Rocket Motor

Real-time erosion of aft dome internal insulation was measured with internal instrumentation on a static test of a lengthened version of the Space Shuffle Reusable Solid Rocket Motor (RSRM). This effort marks the first time that real-time aft dome insulation erosion (Le., erosion due to the combined effects of thermochemical ablation and mechanical abrasion) was measured in this kind of large motor static test [designated as Engineering Test Motor number 3 (ETM3)I. This paper presents data plots of the erosion depth versus time. The data indicates general erosion versus time behavior that is in contrast to what would be expected from earlier analyses. Engineers have long known that the thermal environment in the aft dome is severe and that the resulting aft dome insulation erosion is significant. Models of aft dome erosion involve a two-step process of computational fluid dynamics (CFD) modeling and material ablation modeling. This modeling effort is complex. The time- dependent effects are difficult to verify with only prefire and postfire insulation measurements. Nozzle vectoring, slag accumulation, and changing boundary conditions will affect the time dependence of aft dome erosion. Further study of this data and continued measurements on future motors will increase our understanding of the aft dome flow and erosion environment.

McWhorter, Bruce↗
NASA NTRS1989

Sliding seal materials for low heat rejection engines

Sliding friction coefficients and wear rates of promising piston seal materials were measured under temperature, environmental, velocity, and loading conditions that are representative of the low heat rejection (LHR) diesel engine environment. These materials included carbides, oxides, and nitrides. In addition, silicon nitride and partially stablized zirconia disks (cylinder liners) were ion-implanted with TiNi, Ni, Co, and Cr, and subsequently run against carbide pins (piston rings), with the objective of producing reduced friction via solid lubrication at elevated temperature. Friction and wear measurements were obtained using pin-on-disk laboratory experiments and a unique engine friction test rig. Unmodified ceramic sliding couples were characterized at all temperatures by friction coefficients of 0.24 and above during the pin-on-disk tests. The coefficient at 800 C in an oxidizing environment was reduced to below 0.1, for certain material combination, by the ion-implantation of TiNi or Co. This beneficial effect was found to derive from the lubricious Ti, Ni, and Co oxides. Similar results were demonstrated on the engine friction test rig at lower temperatures. The structural integrity and feasibility of engine application with the most promising material combination were demonstrated during a 30-hour single-cylinder, direct-injection diesel engine test.

Beaty, Kevin↗
DOE OSTI2025

Multifunctional Catalysts for the Tandem Reactions of Oxygenates

Industrially-relevant catalytic reactions rarely consist of a simple sequence of elementary steps. Moreover, kinetic coupling of multiple reactions on a catalyst surface is highly desired for process intensification and improved energy efficiency for large scale chemical transformations. The shifting landscape of hydrocarbon chemical feedstocks in the US also motivates research on the selective conversion of more complex molecules. One desirable type of catalytic reaction is the reduction of carboxylic acids that are produced from biomass feedstocks to their corresponding alcohols. The proposed research explores the fundamental importance of hydrogen spillover on a multifunctional catalyst for carboxylic acid reduction with H 2 composed of metal particles coupled to metal oxide particles. Recent work has demonstrated the excellent performance of supported tungsten oxide clusters for carboxylic acid reduction, but only after they are promoted with a late transition metal such as palladium. Elucidating the active state of the catalyst and the associated reaction mechanism for acid reduction on that active state are the overall goals of the proposed project and successful completion will enable future design of efficient multifunctional catalysts. The critically important role of the metal promoter is hypothesized to be its ability to dissociate H2 and spillover atomic H to the support. Although hydrogen spillover is a well-recognized phenomenon in catalysis, its role in both catalyst activation and catalytic turnover are still unresolved. The study combined materials synthesis, characterization, reactivity testing, and molecular simulations, to explore the effect of hydrogen chemical potential on the formation of the active catalytic sites and on the steady state catalytic reduction of carboxylic acid. Varying the hydrogen chemical potential through modification of the gas conditions, support composition, and metal loading to modulated the structure and catalytic performance of the reducible metal oxide. Dual function catalysts containing supported Pd and WO x species co-located on a non-reducible carrier (silica) and a reducible carrier (titania) were synthesized and characterized by electron microscopy, temperature-programmed reduction, and chemisorption. Spectroscopic methods such as X-ray absorption and UV-vis were also used to evaluate the catalysts, which were used in the reduction of propionic acid to aldehyde and alcohol. Quantum chemical calculations, including ab initio phase diagrams provided molecular insights into the H spillover phenomenon.

09 BIOMASS FUELS↗
NASA NTRS1980

Experimental determination of pure rotary stability derivatives using curved and rolling flow wind tunnel

The technique of using a curved and rolling flow wind tunnel to extract pure rotary stability derivatives is presented. Descriptions of the curved flow and the rolling flow test sections of the Virginia Tech Stability Wind Tunnel are given including methods for obtaining the proper velocity profiles and correcting the data acquired. Results of testing current fighter configurations in this facility are presented with particular attention given to comparing pure rotary derivatives with combined rotary and unsteady derivatives obtained by standard oscillation tests. Also the effect of curved and rolling flow on lateral static stability derivatives is examined.

Lutze, F. H.↗
NASA NTRS1992

Scaling Of Responses Of Composite Beams

Report describes series of experiments in which scale-model composite beams made of matrix/fiber composite materials tested to failure under combined axial compressive and bending loads. Discusses scaling effects in static large-deflection response of composite beams.

Jackson, Karen E.↗
NASA NTRS2007

Viability of NLCD Products From IRS-P6, And From Landsat 7 Scan-gap Data

Landcover test on Salt Lake test site illustrates potential issues with AWiFS/LISS-III for classification of certain land cover classes (evergreen, shrub/scrub, woody wetlands, emergent wetlands). Canopy and impervious graphs of product differences from source indicate slightly lower overall accuracies (shorter peaks, wider bases) for AWiFS/LISS-III, compared to L5/L7. Inspection of individual products from canopy and impervious estimate tests revealed issues with combining AWifs quadrants, and similar but less severe effects with combining multiple dates of L7 scan gap data.

Coan, Michael↗