Search NASA⌕ Search

SEARCH · Search NASA

Results for “Condensation Particle Counter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Twenty years of balloon-borne tropospheric aerosol measurements at Laramie, Wyoming

The paper examines the tropospheric aerosol record obtained over the period 1971 to 1990, during which high-altitude balloons with optical particle counters were launched at Laramie, Wyoming, in a long-term study of the stratospheric sulfate aerosol layer. All aerosol particle size ranges display pronounced seasonal variations, with the condensation nuclei concentration and the optically active component showing a summer maximum throughout the troposphere. Mass estimates, assuming spherical sulfate particles, indicate an average column mass between altitudes of 2.5 and 10 km of about 4 and 16 mg/sq m in winter and summer, respectively. Calculated optical depths vary between 0.01 and 0.04 from winter to summer; the estimated mass scattering cross section is about 3 sq m/g throughout the troposphere. There is evidence for a decreasing trend of 1.6-1.8 percent/yr in the optically active tropospheric aerosol over the past 20 yr, which may be related to a similar reduction in SO2 emission in the U.S. over this period.

Hofmann, David J.↗

Stratosphere aerosol and cloud measurements at McMurdo Station Antarctica during the spring of 1987

Measurements of stratospheric aerosols with balloonborne optical particle counters on 6 occasions at McMurdo Station (78 deg S) in the spring of 1986 indicated subsidence of the stratospheric sulfate layer during the time that the ozone hole was forming (Hofmann et al., 1988). Since dynamic models of ozone depletion involving upwelling in the spring polar vortex would suggest the opposite, we repeated the measurements with an increased frequency (about one sounding per week) in 1987. During 3 of the aerosol soundings in 1986, temperatures in the 15 to 20 km range were low enough (less than 80 C) for HNO3 to co-condense with water according to several theories of polar stratospheric cloud formation. However, particles were not observed with the characteristic size suggested by theory (approx. 0.5 microns). For this reason, it was proposed that polar stratospheric clouds may predominantly consist of large (approx. 5 to 50 microns) ice crystals at very low (approx. 10 sup 4- 10 sup 3 cm cubed) concentrations (Rosen et al., 1988). The particle counter employed would be relatively insensitive to these low concentrations. With the increased frequency of soundings in 1987, and adding additional size discrimination in the 1 to 2 micron region, this hypothesis could be verified if suitably low temperatures were encountered.

Hofmann, D. J.↗

Elastic colloidal monopoles and reconfigurable self-assembly in liquid crystals

Monopole-like electrostatic interactions are ubiquitous in condensed matter, but they are often screened by counter-ions and cannot be switched from attractive to repulsive. In colloidal science, where the main goal is to develop colloidal particles that mimic and exceed the diversity and length scales of atomic and molecular assembly, electrostatically charged particles cannot change the sign of their surface charge or transform from monopoles to higher-order multipoles. In liquid-crystal colloids, elastic interactions between particles arise to minimize the free energy associated with elastic distortions in the long-range alignment of rod-like molecules around the particles. In dipolar quadrupolar and hexadecapolar nematic colloids, the symmetries of such elastic distortions mimic both electrostatic multipoles and the outermost occupied electron shells of atoms. Electric and magnetic switching, spontaneous transformations and optical control of elastic multipoles, as well as their interactions with topological defects and surface boundary conditions, have been demonstrated in such colloids. However, it has long been understood that elastic monopoles should relax to uniform or higher-order multipole states because of the elastic torques that they induce. We develop nematic colloids with strong elastic monopole moments and with elastic torques balanced by the optical torques induced by ambient light. We demonstrate the monopole-to-quadrupole reconfiguration of these colloidal particles by unstructured light, which resembles the driving of atoms between the ground state and various excited states. We show that the sign of the elastic monopoles can be switched, and that like-charged monopoles attract whereas oppositely charged ones repel, unlike in electrostatics. We also demonstrate the out-of-equilibrium dynamic assembly of these colloidal particles. This diverse and surprising behaviour is explained using a model that considers the balance of the optical and elastic torques that are responsible for the excited-state elastic monopoles and may lead to light-powered active-matter systems and self-assembled nanomachines.

36 MATERIALS SCIENCE↗

The GlueX Detector

The GlueX detector is being built along with the new experimental Hall D at Jefferson lab as part of the 12 GeV upgrade project which received CD-3 approval in fall 2008. GlueX is a fixed target experiment built around a 2 Tesla superconducting solenoid having charged particle tracking and calorimetry with large acceptance. A high rate DAQ system consisting of pipeline electronics will allow the detector to operate at high luminosity (10{sup 8} tagged {lambda}/sec on target). Details on the photon beam and GlueX detector are given including capabilities in resolutions and rates.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Fundamental Research Applied To Enable Hardware Performance in Microgravity

NASA sponsors microgravity research to generate knowledge in physical sciences. In some cases, that knowledge must be applied to enable future research. This article describes one such example. The Dust and Aerosol measurement Feasibility Test (DAFT) is a risk-mitigation experiment developed at the NASA Glenn Research Center by NASA and ZIN Technologies, Inc., in support of the Smoke Aerosol Measurement Experiment (SAME). SAME is an investigation that is being designed for operation in the Microgravity Science Glovebox aboard the International Space Station (ISS). The purpose of DAFT is to evaluate the performance of P-Trak (TSI Incorporated, Shoreview, MN)--a commercially available condensation nuclei counter and a key SAME diagnostic- -in long-duration microgravity because of concerns about its ability to operate properly in that environment. If its microgravity performance is proven, this device will advance the state of the art in particle measurement capabilities for space vehicles and facilities, such as aboard the ISS. The P-Trak, a hand-held instrument, can count individual particles as small as 20 nm in diameter in an aerosol stream. Particles are drawn into the device by a built-in suction pump. Upon entering the instrument, these particles pass through a saturator tube where they mix with an alcohol vapor (see the following figure). This mixture then flows through a cooled condenser tube where some of the alcohol condenses onto the sample particles, and the droplets grow in a controlled fashion until they are large enough to be counted. These larger droplets pass through an internal nozzle and past a focused laser beam, producing flashes of light that are sensed by a photodetector and then counted to determine particle number concentration. The operation of the instrument depends on the proper internal flow and recycling of isopropyl alcohol in both the vapor and liquid phases.

Sheredy, William A.↗

Aerosol Inlets for a Mid-Sized Uncrewed Aerial System (UAS)

The purpose of this technical report is to document the efforts to design and test two inlet systems for aerosol sampling suitable for deployment on a medium-sized fixed-wing Uncrewed Aerial System (UAS). This work, which was supported by the U.S. Department of Energy’s Atmospheric Radiation Measurement (ARM) user facility, was conducted at the Pacific Northwest National Laboratory (PNNL) for the ARM Aircraft Facility (AAF) starting in November 2017. The current work is a part of AAF efforts to instrument the ArcticShark (a mid-sized UAS owned and operated by the AAF) for atmospheric research and develop a scientific payload for deployment on a similar-sized UAS with minimal adaptation and integration. An aerosol inlet system is necessary to sample and transport ambient air sample to the scientific instrumentation with minimal distortions to the aerosols. Two isokinetic aerosol inlets were designed: the first is a simple passive system for a single instrument suitable to be installed in a wing pylon; the second is a system with active control designed to sample and distribute air among several heterogeneous instruments and to provide basic humidity control of the air sample so that the measured aerosol parameters should correspond to “dry” conditions (a common requirement). Both systems could be easily adapted for deployment on another platform and/or with a different set of instrumentation. Several conducted flight tests showed that the inlets’ performance met our design goals.

42 ENGINEERING↗

Condensation-nuclei (Aitken Particle) measurement system used in NASA global atmospheric sampling program

The condensation-nuclei (Aitken particle) measuring system used in the NASA Global Atmospheric Sampling Program is described. Included in the paper is a description of the condensation-nuclei monitor sensor, the pressurization system, and the Pollack-counter calibration system used to support the CN measurement. The monitor has a measurement range to 1000 CN/cm cubed and a noise level equivalent to 5 CN/cm cubed at flight altitudes between 6 and 13 km.

Nyland, T. W.↗

EPCAPE-PT-LANL Measurements: Cloud Condensation Nuclei Counter

Coastal cities offer a unique environment for studying aerosol-cloud interactions and the effects of urban emissions on cloud properties. As part of the Eastern Pacific Cloud Aerosol Precipitation Experiment (EPCAPE), the Partitioning Thrust by Los Alamos National Laboratory (EPCAPE-PT-LANL) was conducted. Our campaign focused on measuring the optical and chemical properties of aerosols and their interactions within marine stratocumulus clouds in La Jolla, California. EPCAPE-PT-LANL enhances the primary goals of EPCAPE through innovative observations of vapor-phase transitions between aerosols and cloud droplets, the impact of black carbon on aerosol-cloud dynamics, and the effects of cloud processing on aerosol optical properties. Instrument: Cloud Condensation Nuclei Counter, single column (Droplet Measurements Technology) Files: data_10sec_CCNc.csv, data_10min_CCNc.csv Header: - SuperSaturation[unitless]: The level of supersaturation, expressed as a unitless percentage, at which cloud condensation nuclei (CCN) activity is measured. - NumberConcentration[/cm3]: Number concentration of particles acting as CCN at the baseline supersaturation level, measured in particles per cubic centimeter. - NumberConcentration_SS2[/cm3]: Number concentration of particles acting as CCN at a supersaturation level of 0.2%, measured in particles per cubic centimeter. - NumberConcentration_SS4[/cm3]: Number concentration of particles acting as CCN at a supersaturation level of 0.4%, measured in particles per cubic centimeter. - QualityControl_Flag[bool]: A boolean flag indicating whether the data point passed quality control checks. - CVI_Flag[bool]: A boolean flag indicating whether the Counterflow Virtual Impactor (CVI) was active (true) or inactive (false) during the measurement.

54 ENVIRONMENTAL SCIENCES↗

In situ measurements of particulate number density and size distribution from an aircraft

Two different commercial particulate measuring instruments were flown aboard the NASA Convair 990. A condensation nuclei monitor was utilized to measure particles larger than approximately 0.003 micron in diameter. A specially designed pressurization system was used with this monitor at cabin altitude pressure. A near-forward light scattering counter was used to measure the number and size distribution particles in the size range from 0.5 to 5 microns and greater in diameter. Considerable variation in number density was encountered for both classes of particles at the test altitudes ranging from 5 to 12 km. Presence of clouds could be detected by the light scattering instrument because large numbers of particles would then be registered by the instrument, especially in the size range above 5.0 microns in diameter.

Briehl, D.↗

CCN Measurements at Urban Site during CoURAGE

Cloud condensation nuclei (CCN) measurements were collected during CoURAGE from March - June 2025 at the BSEC urban atmospheric chemistry supersite (39.32057 N, 76.6246 W). CCN number concentrations (# cm-3) were obtained at a frequency of 1 second using a cloud condensation nuclei counter (CCN-100, Droplet Measurement Technologies). The CCN counter was operated in stepping mode, measuring CCN over a range of supersaturations from 0.2 to 1.0%. The settings of the instrument were set such that the supersaturation increased in increments of 0.2% up to the maximum supersaturation, and then decreased in increments of 0.2% down to the minimum supersaturation in a repeating cycle. The supersaturation of the instrument was calibrated weekly using ammonium sulfate. The weekly calibrated supersaturation values have been applied to the data. Data during transitions between supersaturation values were removed and replaced with a value of -999. Transitions are defined as the first 210 seconds after a new supersaturation value to ensure the instrument has stabilized following a change in supersaturation. Data were also flagged with a value of -999 if there were concerns with the function of the instrument, specifically the presence of alarm codes, fogging of the optical particle counter (1st stage monitor > 0.4 V), or a sheath to sample flow ratio outside the expected range (< 9 or > 11).

CCN number density↗

A case of type I polar stratospheric cloud formation by heterogeneous nucleation

The NASA ER-2 aircraft flew on January 24, 1989, from Stavanger to Spitsbergen, Norway, at the 430-440 K potential temperature surface (19.2-19.8 km pressure altitude). Aerosols were sampled continuously by an optical particle counter (PMS-FSSP300) for concentration and size analyses, and during five 10-min intervals by four wire and one replicator impactor for concentration, size, composition, and phase analysis. During sampling, the air saturation of H2O with respect to ice changed from 20 to 100 percent, and of HNO3 with respect to nitric acid trihydrate (NAT) from subsaturation to supersaturation. Data from both instruments indicate a condensation of hydrochloric acid and, later, nitric acid on the background aerosol particles as the ambient temperature decreases along the flight track. This heterogeneous nucleation mechanism generates type I polar stratospheric cloud particles of 10-fold enhanced optical depth, which could play a role in stratospheric ozone depletion.

Pueschel, R. F.↗

Measurements in polar stratospheric clouds over Antarctica in September 1989

The results of six balloon flights at McMurdo Station, Antarctica, under varying temperature conditions, are used in a study of polar stratospheric clouds during Sept. 1989. A particle counter, with size resolution in the 0.5 micron radius region, indicates that cloud size distributions are always bimodal. Mode radii ranging from 0.05 to 0.10 microns were observed for the small particle mode, representing the sulfate layer or condensational growth enhancements of it. The data are not inconsistent with the expected increase in size with decreasing temperature of the small particle mode in the sulfate layer owing to deliquescence although this phenomenon is often masked by nitric acid trihydrate (NAT) condensation when temperatures are sufficiently low. Mode radii generally ranged from 1.5 to 3.5 micron for the large particle mode at concentrations 3 to 4 orders of magnitude lower than the small particle mode. The large particle mode, which normally comprises most of the mass, is presumably caused by NAT condensation on larger particles of the sulfate layer and indicates HNO3 mixing ratios of 1 to 5 ppbv for most of the cloud layers observed, suggesting substantial denitrification. On several occasions, distributions were observed with mode radii as high as 7 microns, and correspondingly large inferred mass, indicating water ice clouds in the 12 to 15 km region. On other occasions, absence of such clouds at very low temperatures indicated water vapor mixing ratios of less than 3 ppmv suggesting dehydration. Generally, the inferred HNO3 mixing ratios were higher in the lower stratosphere, suggesting redistribution through particle sedimentation.

Deshler, Terry↗

Water uptake of clay and desert dust aerosol particles at sub- and supersaturated water vapor conditions

Airborne mineral dust particles serve as cloud condensation nuclei (CCN), thereby influencing the formation and properties of warm clouds. It is therefore of particular interest how dust aerosols with different mineralogy behave when exposed to high relative humidity (RH) or supersaturation with respect to liquid water similar to atmospheric conditions. In this study the sub-saturated hygroscopic growth and the supersaturated cloud condensation nucleus activity of pure clays and real desert dust aerosols was determined using a hygroscopicity tandem differential mobility analyzer (HTDMA) and a cloud condensation nuclei counter (CCNC), respectively. Five different illite, montmorillonite and kaolinite clay samples as well as three desert dust samples (Saharan dust (SD), Chinese dust (CD) and Arizona test dust (ATD)) were used. Aerosols were generated both with a wet and a dry disperser and the water uptake was parameterized via the hygroscopicity parameter, κ. The hygroscopicity of dry generated dust aerosols was found to be negligible when compared to processed atmospheric aerosols, with CCNC derived κ values between 0.00 and 0.02. The latter value can be idealized as a particle consisting of 96.7% (by volume) insoluble material and ~3.3% ammonium sulfate. Pure clay aerosols were found to be generally less hygroscopic than real desert dust particles. All illite and montmorillonite samples had κ~0.003, kaolinites were least hygroscopic and had κ=0.001. SD (κ=0.023) was found to be the most hygroscopic dry-generated desert dust followed by CD (κ=0.007) and ATD (κ=0.003). Wet-generated dust showed an increased water uptake when compared to dry-generated samples. This is considered to be an artifact introduced by redistribution of soluble material between the particles while immersed in an aqueous medium during atomization, thus indicating that specification of the generation method is critically important when presenting such data. Any atmospheric processing of fresh mineral dust which leads to the addition of more than ~3% soluble material is expected to significantly enhance hygroscopicity and CCN activity.

54 ENVIRONMENTAL SCIENCES↗

The role of ions in new particle formation in the CLOUD chamber

The formation of secondary particles in the atmosphere accounts for more than half of global cloud condensation nuclei. Experiments at the CERN CLOUD (Cosmics Leaving OUtdoor Droplets) chamber have underlined the importance of ions for new particle formation, but quantifying their effect in the atmosphere remains challenging. By using a novel instrument setup consisting of two nanoparticle counters, one of them equipped with an ion filter, we were able to further investigate the ion-related mechanisms of new particle formation. In autumn 2015, we carried out experiments at CLOUD on four systems of different chemical compositions involving monoterpenes, sulfuric acid, nitrogen oxides, and ammonia. We measured the influence of ions on the nucleation rates under precisely controlled and atmospherically relevant conditions. Our results indicate that ions enhance the nucleation process when the charge is necessary to stabilize newly formed clusters, i.e., in conditions in which neutral clusters are unstable. For charged clusters that were formed by ion-induced nucleation, we were able to measure, for the first time, their progressive neutralization due to recombination with oppositely charged ions. A large fraction of the clusters carried a charge at 1.5 nm diameter. However, depending on particle growth rates and ion concentrations, charged clusters were largely neutralized by ion–ion recombination before they grew to 2.5 nm. At this size, more than 90 % of particles were neutral. In other words, particles may originate from ion-induced nucleation, although they are neutral upon detection at diameters larger than 2.5 nm. Observations at Hyytiälä, Finland, showed lower ion concentrations and a lower contribution of ion-induced nucleation than measured at CLOUD under similar conditions. Although this can be partly explained by the observation that ion-induced fractions decrease towards lower ion concentrations, further investigations are needed to resolve the origin of the discrepancy.

54 ENVIRONMENTAL SCIENCES↗

Mixing-height measurement by lidar, particle counter, and rawinsonde in the Williamette Valley, Oregon

The feasibility of using laser radar (lidar) to measure the spatial distribution of aerosols and water vapor in the earth's mixing or boundary layer is shown. From these data the important parameter of actual mixing height was determined, that is, the maximum height to which particulate pollutants actually mix. Data are shown for simultaneous lidar, rawinsonde, and aircraft-mounted condensation nuclei counter and temperature measurements. The synoptic meteorology is also presented. The Williamette Valley, Oregon, was chosen for the measurements because of its unique combination of meteorology, terrain, and pollutant source, along with an ongoing Oregon State University study of the natural ventilation of this valley.

Mccormick, M. P.↗

Unusual behavior in the condensation nuclei concentration at 30 km

The result obtained with an improved balloon-borne condensation nuclei (CN) counter that is capable of operating to altitudes of at least 30 km are presented. Of major interest is the appearance of a quasiannual variation near 30 km which could be described by a sudden concentration increase of unusually small particles occurring in the winter or spring followed by a 1- to 3-month decay period to background levels. The magnitude of the variation has increased dramatically following the recent generally high levels of volcanic activity affecting the lower stratosphere. Several potential explanations for the event are considered, but none appear entirely satisfactory or complete at the present time. The explanation with the fewest drawbacks would attribute the production of growth of the new cn to a highly supersaturated H2SO4 vapor layer generated by any one of several proposed processes in the upper high latitude stratosphere.

Rosen, J. M.↗

Preliminary investigation of a water-based method for fast integrating mobility spectrometry

A water-based condensational growth channel was developed for imaging mobility-separated particles within a parallel plate separation channel of the Fast Integrated Mobility Spectrometer (FIMS). Reported are initial tests of that system, in which the alcohol condenser of the FIMS was replaced by a water-based condensational growth channel. Tests with monodispersed sodium chloride aerosol verify that the water-condensational growth maintained the laminar flow, while providing sufficient growth for particle imaging. Particle positions mapped onto particle mobility, in accordance with theoretical expectations. Particles ranging in size from 12 nm to 100 nm were counted with the same efficiency as with a butanol-based ultrafine particle counter, once inlet and line losses were taken into account.

54 ENVIRONMENTAL SCIENCES↗