Search NASA⌕ Search

SEARCH · Search NASA

Results for “Corrected coefficients”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Experimental Investigation of a Flexible Wing with a Variable Camber Continuous Trailing Edge Flap Design

This paper presents experimental results of a flexible wing wind tunnel model with a variable camber continuous trailing edge flap (VCCTEF) design for drag minimization, tested at the University of Washington Aeronautical Labo- ratory (UWAL). The wind tunnel test was designed to explore the relative merit of the VCCTEF concept for improved cruise efficiency through the use of low-cost aeroelastic model test techniques. The flexible wing model is a 10-scaled model of a typical transport wing and is constructed of woven fabric composites and foam core. The wing structural stiffness in bending is tailored to be half of the stiffness of a Boeing 757-era transport wing, while the torsional stiffness is about the same. This stiffness reduction results in a wing tip deflection of about 10 of the wing semi-span. The VCCTEF is a multi-segment flap design having three chordwise camber segments and five spanwise flap sections for a total of 15 individual flap elements. The three chordwise camber segments can be positioned appropriately to create a desired trailing edge camber. Elastomeric material is used to cover the gaps in between the spanwise flap sections, thereby creating a continuous trailing edge. Wind tunnel data indicate a high degree of data correlation and repeata- bility. The VCCTEF can achieve a drag reduction of up to 6.31 and an improvement in the lift-to-drag ratio (LD) of up to 4.85. The paper also presents two methods for estimating the lift coefficient of a rigid wing using a dynamic pressure correction and an aeroelastic deflection correction. Both methods provide good estimates of the rigid-wing lift coefficient.

Aerodynamics↗
NASA NTRS2022

MODIS TEB Electronic Crosstalk Correction Update and Impact on L1B Product Uncertainty

The MODIS instruments onboard the Terra and Aqua satellites have been in operation for over22 and 20 years, respectively. The instruments’ calibration accuracy has been maintained, even with instrument degradation. Electronic crosstalk in the thermal emissive bands (TEB) is a known issue with an increasing impact on the calibration and product. The Terra MODIS photovoltaic (PV) longwave infrared (LWIR) bands crosstalk corrections have been applied in Collection 6.1 (C6.1). However, the electronic crosstalk contamination for some detectors in the mid-wave infrared (MWIR) bands and the Aqua PVLWIR bands affect the Level-1B (L1B) product’s measurement accuracy and image quality. In Collection 7 (C7), crosstalk corrections for select detectors in the Terra and Aqua MWIR and Aqua PV LWIR bands are applied. The entire mission crosstalk coefficients for the select detectors and bands are derived from scheduled lunar observations and populated in the form of look-up tables (LUTs). The Aqua PV-LWIR bands exhibit similar downward crosstalk trends as the Terra PV-LWIR bands, especially in recent years. The crosstalk coefficients and their trends provide a guideline for the correction application. Earth measurement analyses before and after the correction provide contamination and correction assessments. It has been shown that the product quality is enhanced with the crosstalk correction applied in C7. For C7, the crosstalk coefficient uncertainty is derived from the fit residuals between the measured values and a linear fit over a three-year sliding window. The uncertainty propagation is modeled and applied in the total uncertainty calculation intheL1B product. The TEB electronic crosstalk LUTs have been processed over the entire Terra and Aqua MODIS missions. This paper presents the C7 crosstalk correction, as well as its assessment and uncertainty propagation algorithm to the TEB uncertainty.

Tiejun Chang↗
NASA NTRS2022

Modis TEB Electronic Crosstalk Correction Update and Impact on L1B Product Uncertainty

The MODIS instruments on board the Terra and Aqua satellites have been in operation for over 22 and 20 years, respectively. The instruments’ calibration accuracy has been maintained, even with instrument degradation. Electronic crosstalk in the thermal emissive bands (TEB) is a known issue with an increasing impact on the calibration and product. The Terra MODIS photovoltaic (PV) longwave infrared (LWIR) bands crosstalk corrections have been applied in Collection 6.1 (C6.1). However, the electronic crosstalk contamination for some detectors in the mid-wave infrared(MWIR) bands and the Aqua PVLWIR bands affect the Level-1B(L1B) product’s measurement accuracy and image quality. In Collection 7 (C7), crosstalk corrections for select detectors in the Terra and Aqua MWIR and Aqua PV LWIR bands are applied. The entire mission crosstalk coefficients for the select detectors and bands are derived from scheduled lunar observations and populated in the form of look-up tables (LUTs). The Aqua PV-LWIR bands exhibit similar downward crosstalk trends as the Terra PV-LWIR bands, especially in recent years. The crosstalk coefficients and their trends provide a guideline for the correction application. Earth measurement analyses before and after the correction provide contamination and correction assessments. It has been shown that the product quality is enhanced with the crosstalk correction applied in C7. For C7, the crosstalk coefficient uncertainty is derived from the fit residuals between the measured values and a linear fit over a three-year sliding window. The uncertainty propagation is modeled and applied in the total uncertainty calculation intheL1B product. The TEB electronic cross talk LUT shave been processed over the entire Terra and Aqua MODIS missions. This paper presents the C7 crosstalk correction, as well as its assessment and uncertainty propagation algorithm to the TEB uncertainty.

Tiejun Chang↗
NASA NTRS1978

Forwardscattering corrections for optical extinction measurements in aerosol media. I - Monodispersions

A parametric investigation of forwardscattering corrections applicable to experimentally determined optical extinction coefficients in homogeneous aerosol media is discussed for the case of monodispersion. Assuming forwardscattering to be a single-scattering phenomenon, corrections are made by two methods: one employing the exact Mie theory, the other employing the approximate Rayleigh diffraction formula. The corrections are evaluated as functions of particle size, the real and imaginary parts of the complex refractive index, and the half-angle of the detector view cone.

Deepak, A.↗
NASA NTRS2002

Implementation of the NCAR Community Land Model (CLM) in the NASA/NCAR finite-volume Global Climate Model (fvGCM)

In this study, the NCAR CLM version 2.0 land-surface model was integrated into the NASA/NCAR fvGCM. The CLM was developed collaboratively by an open interagency/university group of scientists and based on well-proven physical parameterizations and numerical schemes that combine the best features of BATS, NCAR-LSM, and IAP94. The CLM design is a one-dimensional point model with 1 vegetation layer, along with sub-grid scale tiles. The features of the CLM include 10-uneven soil layers with water, ice, and temperature states in each soil layer, and five snow layers, with water flow, refreezing, compaction, and aging allowed. In addition, the CLM utilizes two-stream canopy radiative transfer, the Bonan lake model and topographic enhanced streamflow based on TOPMODEL. The DAO fvGCM uses a genuinely conservative Flux-Form Semi-Lagrangian transport algorithm along with terrain- following Lagrangian control-volume vertical coordinates. The physical parameterizations are based on the NCAR Community Atmosphere Model (CAM-2). For our purposes, the fvGCM was run at 2 deg x 2.5 deg horizontal resolution with 55 vertical levels. The 10-year climate from the fvGCM with CLM2 was intercompared with the climate from fvGCM with LSM, ECMWF and NCEP. We concluded that the incorporation of CLM2 did not significantly impact the fvGCM climate from that of LSM. The most striking difference was the warm bias in the CLM2 surface skin temperature over desert regions. We determined that the warm bias can be partially attributed to the value of the drag coefficient for the soil under the canopy, which was too small resulting in a decoupling between the ground surface and the canopy. We also discovered that the canopy interception was high compared to observations in the Amazon region. A number of experiments were then performed focused on implementing model improvements. In order to correct the warm bias, the drag coefficient for the soil under the canopy was considered a function of LAI (Leaf Area Index). Analysis of the results revealed that there was a substantial impact, and the warm and dry bias in the CLM2 was significantly reduced. For the interception scheme, the canopy throughfall was increased to allow for more infiltration of precipitation into the soil, resulting in increased low-level moisture and a decrease in the interception loss ratio (canopy evaporation to precipitation).

Radakovich, Jon D.↗
NASA NTRS2001

Application of Pressure-Based Wall Correction Methods to Two NASA Langley Wind Tunnels

This paper is a description and status report on the implementation and application of the WICS wall interference method to the National Transonic Facility (NTF) and the 14 x 22-ft subsonic wind tunnel at the NASA Langley Research Center. The method calculates free-air corrections to the measured parameters and aerodynamic coefficients for full span and semispan models when the tunnels are in the solid-wall configuration. From a data quality point of view, these corrections remove predictable bias errors in the measurement due to the presence of the tunnel walls. At the NTF, the method is operational in the off-line and on-line modes, with three tests already computed for wall corrections. At the 14 x 22-ft tunnel, initial implementation has been done based on a test on a full span wing. This facility is currently scheduled for an upgrade to its wall pressure measurement system. With the addition of new wall orifices and other instrumentation upgrades, a significant improvement in the wall correction accuracy is expected.

Iyer, V.↗
NASA NTRS1977

A model of the 1.6 GHz scatterometer

The performance was studied of the 1.6 GHz airborne scatterometer system which is used as one of several Johnson Space Center (JSC) microwave remote sensors to detect moisture content of soil. The system is analyzed with respect to its antenna pattern and coupling, the signal flow in the receiver data channels, and the errors in the signal outputs. The operational principle and the sensitivity of the system, as well as data handling are also described. The finite cross-polarized gains of all four 1.6 GHz scatterometer antennae are found to have profound influence on the cross-polarized backscattered signal returns. If these signals are not analyzed properly, large errors could result in the estimate of the cross-polarized coefficient. It is also found necessary to make corrections to the variations of the aircraft parameters during data reduction in order to minimize the error in the coefficient estimate. Finally, a few recommendations are made to improve the overall performance of the scatterometer system.

Wang, J. R.↗
NASA NTRS1947

Altitude-Wind-Tunnel Investigation of the 19B-2, 19B-8 and 19XB-1 Jet- Propulsion Engines: Analysis of Compressor Performance - 4

Investigations were conducted in the Cleveland altitude wind tunnel to determine the performance and operational characteristics of the 19B-2, 19B-8, and 19XS-1 turbojet engines. One objective was to determine the effect of altitude, flight Mach number, and tail-pipe-nozzle area on the performance characteristics of the six-stage and ten-stage axial-flow compressors of the 19B-8 and 19XB-1 engines, respectively, The data were obtained over a range of simulated altitudes and flight Mach numbers. At each simulated flight condition the engine was run over its full operable range of speeds. Performance characteristics of the 19B-8 and 19XB-1 compressors for the range of operation obtainable in the turboJet-engine installation are presented. Compressor characteristics are presented as functions of air flow corrected to sea-level conditions, compressor Mach number, and compressor load coefficient. For the range of compressor operation investigated, changes in Reynolds number had no measurable effect on the relations among compressor Mach number, corrected air flow, compressor load coefficient, compressor pressure ratio, and compressor efficiency. The operating lines for the 19B-8 compressor lay on the low-air-flow side of the region of maximum compressor efficiency; the 19B-8 compressor operated at higher average pressure coefficients per stage and produced a lower over-all pressure ratio than did the 19XB-1 compressor.

Dietz, Robert O.↗
NASA NTRS1989

Downward continuation of the free-air gravity anomalies to the ellipsoid using the gradient solution and terrain correction: An attempt of global numerical computations

The formulas for the determination of the coefficients of the spherical harmonic expansion of the disturbing potential of the earth are defined for data given on a sphere. In order to determine the spherical harmonic coefficients, the gravity anomalies have to be analytically downward continued from the earth's surface to a sphere-at least to the ellipsoid. The goal is to continue the gravity anomalies from the earth's surface downward to the ellipsoid using recent elevation models. The basic method for the downward continuation is the gradient solution (the g sub 1 term). The terrain correction was also computed because of the role it can play as a correction term when calculating harmonic coefficients from surface gravity data. The fast Fourier transformation was applied to the computations.

Wang, Y. M.↗
NASA NTRS1972

Distribution of error in least-squares solution of an overdetermined system of linear simultaneous equations

Probability density functions were derived for errors in the evaluation of unknowns by the least squares method in system of nonhomogeneous linear equations. Coefficients of the unknowns were assumed correct and computational precision were also assumed. A vector space was used, with number of dimensions equal to the number of equations. An error vector was defined and assumed to have uniform distribution of orientation throughout the vector space. The density functions are shown to be insensitive to the biasing effects of the source of the system of equations.

Miller, C. D.↗
NASA NTRS1973

New approach to cosmic-ray diffusion theory.

We have investigated a new approach to deriving a diffusion equation for charged particles in a static, random magnetic field. Our method incorporates essential effects of the magnetic fluctuations in the lowest order particle orbits. Significant corrections to the usual quasilinear diffusion coefficient for cosmic rays with pitch angles near 90 deg are a consequence. Monte Carlo results bear out the validity of our theory.

Jones, F. C.↗
NASA NTRS1975

Numerical procedure for analyzing Langmuir probe data

A numerical procedure is proposed for analyzing Langmuir probe data in the presence of a two-group plasma containing both primary and Maxwellian electrons. The procedure is known as a least-squares differential-correction technique for determining the unknown coefficients of the governing equation. It is shown that for a given set of input data the results of the analysis are unique and independent of the initial estimate of electron temperature, that convergence is fastest when electron temperature is overestimated, that the results are sensitive to the region of the curve used as input and also to the voltage increment, and that plasma properties determined by the proposed numerical procedure are either consistent with those determined graphically or closer to expected values. With a suitable data acquisition system, the Fortran IV program worked out for this procedure could be used to provide real-time plasma diagnostic information for an operating ion thruster.

Beattie, J. R.↗
NASA NTRS1976

9.6 micrometer ozone band /nu sub 3/ intensity

The band intensity of the 9.6 micrometer (nu sub 3) band of ozone was investigated. The nu sub 3 band strength was determined from ultraviolet spectra over the interval 9.36-11.00 micrometers. A set of 34 absorption measurements were made at pressures of about 730 torr and mass paths of 0.002-0.025 atm cm (STP). The ozone amounts were corrected to the Harn (1961) absorption coefficients. The data indicate that the weak-line approximation is valid at least to 0.025 atm cm (STP). A least-squares fit yields a band strength (298 K) of 355/cm/atm cm STP with a standard deviation of 10/cm/atm cm STP, in close agreement with results reported by McCaa and Shaw (1968) and Young and Bunner (1974).

Bartman, F. L.↗
NASA NTRS1981

An objective method for determining the generalized transport tensor for two-dimensional Eulerian models

An objective method for deriving the components of a generalized transport tensor for a two-dimensional model is presented. Representative meridional and vertical velocities and thermodynamic scalars at a uniform grid are used to reduce the problem to the solution of two flux equations for two unknowns. One unknown is the stream-function, coefficient of an antisymmetric tensor, which corrects the Eulerian mean motions for Stokes drift; the other is a time constant, which converts the deviatory velocity tensor to a symmetric transport tensor. The complete asymmetric tensor, called a transport tensor, has a divergence which yields both advection and diffusion by the deviatory velocities. Advantages and disadvantages of Lagrangian and Eulerian averages are discussed, and meridional-vertical velocity correlations are provided.

Danielsen, E. F.↗
NASA NTRS1984

Transonic solutions for a multielement airfoil using the full-potential equation

Transonic flow solutions are obtained over a multielement airfoil (augmentor-wing) using the full-potential equation. Solutions obtained for a subcritical case and a strong shock case show good quantitative agreement with experiment in regions not dominated by viscous effects. In those regions where viscous effects are dominant, the results are still in good qualitative agreement. For the strong shock case, Mach number and angle-of-attack corrections were necessary to match experimental coefficient of lift. Typical results from the transonic augmentor-wing Potential Code on the Cray-1S computer require about 10 sec of CPU time for a three-order-of-magnitude drop in the maximum residual. The speed with which solutions can be generated, and the associated low cost, will make this code a practical tool for the design aerodynamicist.

Flores, J.↗
NASA NTRS1987

Maximum survival capability of an aircraft in a severe windshear

The performance of constant-alpha, maximum-alpha, constant-velocity, constant-absolute-inclination, constant-climb-rate, and constant-pitch (CP) vertical-plane guidance schemes for aircraft taking off under horizontal-windshear conditions with a downdraft is compared by means of numerical simulations; the results are presented in tables and graphs, and it is found that CP guidance gives the best aircraft survivability. Optimal, gamma-guidance, and simplified-gamma trajectories are then evaluated to improve the performance of CP, and the correct selection of the feedback gain coefficient and the time delay for response to windshear onset is shown to be of great importance for maximizing survivability.

Miele, A.↗
NASA NTRS1991

The NASA aircraft noise prediction program improved propeller analysis system

The improvements and the modifications of the NASA Aircraft Noise Prediction Program (ANOPP) and the Propeller Analysis System (PAS) are described. Comparisons of the predictions and the test data are included in the case studies for the flat plate model in the Boundary Layer Module, for the effects of applying compressibility corrections to the lift and pressure coefficients, for the use of different weight factors in the Propeller Performance Module, for the use of the improved retarded time equation solution, and for the effect of the number grids in the Transonic Propeller Noise Module. The DNW tunnel test data of a propeller at different angles of attack and the Dowty Rotol data are compared with ANOPP predictions. The effect of the number of grids on the Transonic Propeller Noise Module predictions and the comparison of ANOPP TPN and DFP-ATP codes are studied. In addition to the above impact studies, the transonic propeller noise predictions for the SR-7, the UDF front rotor, and the support of the enroute noise test program are included.

Nguyen, L. Cathy↗