Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cu surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

An experimental investigation of silicon wafer surface roughness and its effect on the pull-strength of plated metals

Plated silicon wafers with surface roughness ranging from 0.4 to 130 microinches, subjected to tensile pull-strength tests, were analyzed. Results show that the measured pull-strength of plated metals decrease with increasing silicon surface roughness, effecting a weakening of the cohesive strength of the wafer, possibly caused by microcracks or 'etch pits' in the silicon surface. The mean value of pull-strength for all wafers plated with the Ni-Cu-Cu sequence exceeded the required 450 g/0.02 sq cm, and at Ra = 0.4 microinches, the mean pull-strength for the Ni-Cu-Cu and Ni-Cu wafers were 2290 and 850 g/0.02 sq cm, respectively. The development of standardized methods for measuring contact pull-strength is suggested. These results may have some bearing on solar cell arrays problems.

Spiers, G. D.↗
NASA NTRS1986

Relation between L-band soil emittance and soil water content

An experimental relation between soil emittance (E) at L-band and soil surface moisture content (M) is compared with a theoretical one. The latter depends on the soil dielectric constant, which is a function of both soil moisture content and of soil texture. It appears that a difference of 10 percent in the surface clay content causes a change in the estimate of M on the order of 0.02 cu m/cu m. This is based on calculations with a model that simulates the flow of water and energy, in combination with a radiative transfer model. It is concluded that an experimental determination of the E-M relation for each soil type is not required, and that a rough estimate of the soil texture will lead to a sufficiently accurate estimate of soil moisture from a general, theoretical relationship obtained by numerical simulation.

Stroosnijder, L.↗
NASA NTRS1992

Pancakelike domes on Venus

The shape of seven large domes on the plains of Venus, with volumes between 100 and 1000 cu km, is compared with that of an axisymmetric gravity current spreading over a rigid horizontal surface. Both the altimetric profiles and the horizontal projection of the line of intersection of domes on the SAR images agree well with the theoretical similarity solution for a newtonian fluid, but not with the shape calculated for a rigid-plastic rheology, nor with that for a static model with a strong skin. As a viscous current spreads, it generates an isotropic strain rate tensor whose magnitude is independent of radius. Such a flow can account for the randomly oriented cracks that are uniformly distributed on the surface of the domes. The stress induced by the flow in the plains material below is obtained, and is probably large enough to produce the short radial cracks in the surface of the plains beyond the domes. The viscosity of the domes can be estimated from their thermal time constants if spreading is possible only when the fluid is hot, and lies between 10(exp 14) and 10(exp 17) Pa s. Laboratory experiments show that such viscosities correspond to temperatures of 610 - 690 C in dry rhyolitic magmas. These temperatures agree with laboratory measurements of the solidus temperature of wet rhyolite. These results show that the development of the domes can be understood using simple fluid dynamical ideas, and that the magmas involved can be produced by wet melting at depths below 10 km, followed by eruption and degassing.

Mckenzie, Dan↗
NASA NTRS1991

Creep behavior of copper at intermediate temperatures. II - Surface microstructural observations. III - A comparison with theory

Three different types of microstructural slip features are noted to occur during the creep of Cu at 0.46-0.72 of absolute melting point. While single slip is associated with higher temperatures and lower stresses, complex wavy slip features are observed at higher temperatures and higher stresses as well as with increasing strains: suggesting the importance of cross-slip mechanisms. At lower temperatures and higher stresses the multiple-slip morphologies observed indicate that cross-slip mechanisms may control the creep of polycrystalline Cu only over a limited stress and temperature range. A phenomenological model is proposed which assumes that (1) cell boundaries within subgrains act as both sources of, and obstacles to, gliding dislocations, and (2) dislocation annihilation occurs at the cell boundaries by climb and cross-slip.

Raj, S. V.↗
NASA NTRS1982

Sorption of noble gases by solids, with reference to meteorites. II - Chromite and carbon. III - Sulfides, spinels, and other substances; on the origin of planetary gases

The trapping of noble gases by chromite and carbon, two putative carriers of primordial noble gases in meteorites, was studied by synthesizing 19 samples in a Ne-Ar-Kr-Xe atmosphere at 440-720 K. Noble gas contents are found to approximately obey Henry's Law, but only slight correlations are found with composition, surface area, or adsorption temperature. Geometric mean distribution coefficients for bulk samples and HCl residues in 10 cu cm STP/g atm are: Xe 100, Kr 15, Ar 3.5, and Ne 0.62. Elemental fractionation data support the suggestion of Lewis et al. (1977) that chromite and carbon in C2 and C3 chondrites were formed by the reaction: Fe, Cr + 4CO yields (Fe, Cr)3O4 + 4C + carbides. In contrast to meteoritic minerals, the synthetic specimens show no isotopic fractionation of noble gases. In a subsequent study, attention is given to the cases of sulfides and spinels, on the way to consideration of the origin of planetary gases. Sulfides showed three distinctive trends relative to chromite or magnetite. The elemental fractionation pattern of Ar, Kr and Xe in meteorites, terrestrial rocks and planets resembles the adsorption patterns on the carbons, spinels, sulfides, and other solids studied. The high release temperature of meteoritic noble gases may be explained by transformation of the physisorbed or chemisorbed gas. The ready loss of meteoritic heavy gases on surficial oxidation is consistent with adsorption, as is the high abundance.

Yang, J.↗
NASA NTRS2011

Autonomous Coordination of Science Observations Using Multiple Spacecraft

This software provides capabilities for autonomous cross-cueing and coordinated observations between multiple orbital and landed assets. Previous work has been done in re-tasking a single Earth orbiter or a Mars rover in response to that craft detecting a science event. This work enables multiple spacecraft to communicate (over a network designed for deep-space communications) and autonomously coordinate the characterization of such a science event. This work investigates a new paradigm of space science campaigns where opportunistic science observations are autonomously coordinated among multiple spacecraft. In this paradigm, opportunistic science detections can be cued by multiple assets where a second asset is requested to take additional observations characterizing the identified surface feature or event. To support this new paradigm, an autonomous science system for multiple spacecraft assets was integrated with the Interplanetary Network DTN (Delay Tolerant Network) to provide communication between spacecraft assets. This technology enables new mission concepts that are not feasible with current technology. The ability to rapidly coordinate activities across spacecraft without requiring ground in the loop enables rapid reaction to dynamic events across platforms, such as a survey instrument followed by a targeted high resolution instrument, as well as regular simultaneous observations.

Estlin, Tara A.↗
NASA NTRS2014

Column Aerosol Optical Properties and Aerosol Radiative Forcing During a Serious Haze-Fog Month over North China Plain in 2013 Based on Ground-Based Sunphotometer Measurements

In January 2013, North China Plain experienced several serious haze events. Cimel sunphotometer measurements at seven sites over rural, suburban and urban regions of North China Plain from 1 to 30 January 2013 were used to further our understanding of spatial-temporal variation of aerosol optical parameters and aerosol radiative forcing (ARF). It was found that Aerosol Optical Depth at 500 nm (AOD500nm) during non-pollution periods at all stations was lower than 0.30 and increased significantly to greater than 1.00 as pollution events developed. The Angstrom exponent (Alpha) was larger than 0.80 for all stations most of the time. AOD500nm averages increased from north to south during both polluted and non-polluted periods on the three urban sites in Beijing. The fine mode AOD during pollution periods is about a factor of 2.5 times larger than that during the non-pollution period at urban sites but a factor of 5.0 at suburban and rural sites. The fine mode fraction of AOD675nm was higher than 80% for all sites during January 2013. The absorption AOD675nm at rural sites was only about 0.01 during pollution periods, while 0.03-0.07 and 0.01-0.03 during pollution and non-pollution periods at other sites, respectively. Single scattering albedo varied between 0.87 and 0.95 during January 2013 over North China Plain. The size distribution showed an obvious tri-peak pattern during the most serious period. The fine mode effective radius in the pollution period was about 0.01-0.08 microns larger than during nonpollution periods, while the coarse mode radius in pollution periods was about 0.06-0.38 microns less than that during nonpollution periods. The total, fine and coarse mode particle volumes varied by about 0.06-0.34 cu microns, 0.03-0.23 cu microns, and 0.03-0.10 cu microns, respectively, throughout January 2013. During the most intense period (1-16 January), ARF at the surface exceeded −50W/sq m, −180W/sq m, and −200W/sq m at rural, suburban, and urban sites, respectively. The ARF readings at the top of the atmosphere were approximately −30W/sq m in rural and −40-60W/sq m in urban areas.

Atmosphere↗
NASA NTRS1989

Intrinsic fatigue crack propagation in aluminum-lithium alloys - The effect of gaseous environments

Gaseous environmental effects on intrinsic fatigue crack growth are significant for the Al-Li-Cu alloy 2090, peak aged. For both moderate Delta K-low R and low Delta K-high R regimes, crack growth rates decrease according to the environment order: purified water vapor, moist air, helium and oxygen. Gaseous environmental effects are pronounced near threshold and are not closure dominated. Here, embrittlement by low levels of H2O (ppm) supports hydrogen embrittlement and suggests that molecular transport controlled cracking, established for high Delta K-low R, is modified near threshold. Localized crack tip reaction sites or high R crack opening shape may enable the strong, environmental effect at low levels of Delta K. Similar crack growth in He and O2 eliminates the contribution of surface films to fatigue damage in alloy 2090. While 2090 and 7075 exhibit similar environmental trends, the Al-Li-Cu alloy is more resistant to intrinsic corrosion fatigue crack growth.

Piascik, Robert S.↗
NASA NTRS1999

Characterization of the Heat Extraction Capability of a Compliant, Sliding, Thermal Interface for Use in a High Temperature, Vacuum Microgravity Furnace

Much of the material science gained in microgravity research requires processing a sample in a high performance furnace. One such furnace currently being designed is the Quench Module Insert (QMI). The Principle Investigators, for whom the furnace is proposed, require high temperature gradients in their cylindrical samples to achieve the science objectives. One of the components critical to achieving high sample axial temperature gradients in the Quench Module Insert is a high performance cold zone to extract the heat from the sample. This cold zone employs a compliant, sliding thermal interface based on a Vel-Therm felt. This felt provides a conductive path between the Sample Cartridge Assembly (SCA) exterior surface and the interior surface of the water cooled chill block while allowing movement of the sample relative to the chill block. The Vel-Therm felt is composed of long polymer-based fibers affixed to a thin flexible substrate layer. The fibers are oriented perpendicular to this substrate giving the felt the appearance of a velvet fabric. The Vel-Therm felt heat extraction capability was quantified in earlier tests performed in an inert gas environment. The current activity, described in this paper, is intended to characterize the extraction capability of Vel-Therm felt in a vacuum environment similar to the QMI environment. This testing is necessary to quantify the thermal performance of the Vel-Therm felt and the sensitivity of that performance to key variables. The data derived from these tests will be incorporated into the current thermal models to improve the quality of the models and reduce uncertainty of the analytical results. In addition, the data will be used to help select the appropriate Vel-Therm felt and set proper operating limits as well as assess the performance range of the furnace. The objective of this test is to measure the heat extraction rate of the Vel-Therm felt as specified by the effective heat transfer coefficient. Therefore, the test setup was designed to force the bulk of the heat transfer through the area where the Vel-Therm felt was applied. A heat source, consisting of a ceramic heating element encased in a Copper (Cu) housing is mounted on four isolated support rods. A 6-layer molybdenum radiation shield is used to insulate against heat loss from the heater and prevent heat exchange between the hot and cold sides of the test apparatus. The Vel-Therm felt is affixed to the surface of the cold sink, a water-cooled Cu chill block. An adjustable plate supports and isolates the cold sink from above and is used to control the amount of the deflection of the Vel- Therm when in contact with the Cu heating element housing. The primary means of establishing the power being conducted through the felt is to measure the energy being transferred to the water passing through the chill block. Analysis was performed to support the assumption that the source and sink surfaces were approximately isothermal under the specific test conditions. As a check on the amount of power passing through the felt, the power supplied to the heater was also measured. Thermocouples were strategically located throughout the test apparatus for measurement purposes. A bell jar was lowered over the assembly to impose vacuum conditions. Currently, variables tested have been fiber compression and fiber type and surface temperatures (both the hot and cold side temperatures are hypothesized to be important to the performance of the Vel-Therm.) Selected runs were repeated to ensure consistency and repeatability. Results obtained thus far reveal that Vel-Therm performance is significantly degraded by fibers being exposed to high compression. It also shows that performance is somewhat negatively impacted by previous compression, thereby, raising the question of repeatability. In addition, early results show a significant dependence on temperature. A computer aided mathematical analysis of the test setup is ongoing. The results will be correlated to actual results. The correlation will examine such details as parasitic loses, conduction down the power leads and many other concerns.

Bellomy-Ezell, Jenny↗
NASA NTRS2024

Combining Multi-Faceted Laboratory Studies of 74001-2 and Regional Remote Sensing to Address How Pyroclastic Eruptions Record and Affect the Lunar Volatile Budget

Basaltic magmatism is an efficient process for bringing volatiles from a planetary interior to its surface, with the possibility of generation of a transient lunar atmosphere as abundant volcanic materials de-gassed. However, pyroclastic deposits are locations where trapped gases may be studied [e.g., 2,3]. Volatile-rich pyroclastic deposits occur over a wide surface area of the Moon, indicating that the transport of volatiles and associated pyroclastic materials from the Moon’s mantle to the surface was a wide-spread phenomenon. Numerous studies analyzing remotely sensed data and using empirical modeling have demonstrated that various stages of pyroclastic eruptions significantly influence gas release patterns, morphology, and mineralogy of the deposit. Many observations based on mare basalts and pyroclastic deposits have identified potential histories of gas release [e.g., 2-10] and their influence on volatiles and their stable isotopes [e.g., 11-13]. The best representation of these pyroclastic deposits in the sample collection is core sample 74001-74002 that was collected during the Apollo 17 mission to the Taurus-Littrow Valley (TLV). The double drive tube penetrated a part of a regional-scale pyroclastic deposit and sampled approximately 68.1 cm of that deposit in the TLV. Remnants of this and other pyroclastic depos-its are represented throughout and beyond the TLV [e.g., 14-16]. The stratigraphy of this core has been investigated and defined by numerous studies. The CASA Moon SSERVI research team is conducting a multi-faceted analytical study of this deposit. Data generated from revisiting the stratigraphy of 74001-74002 will be used to place stable isotopes (H, B, Cl, S, Zn, Cu, Rb, Ga, Pb), Ar-Ar and U-Pb chronology, geochemistry, nanometer-scale observations of mineral surfaces, orbital observations, and experiments and modeling within a stratigraphic, eruptive, and geologic context. It is important to place these data into such a context. For example, recent S isotope measurements reported by Dottin et al. show differences within this core that may be related to either changes in source or eruptive process over the course of the eruption (vs. multiple eruptions). A fuller understanding of the stratigraphy is fundamental to resolving this interpretation. This comprehensive approach can only be achieved within the context of a program such as SSERVI. In addition, imaging produced in this project will be incorporated into a citizen scientist program to further identify many of the textural features of this double drive tube.

SSERVI↗
NASA NTRS1994

Innovative instrumentation for mineralogical and elemental analyses of solid extraterrestrial surfaces: The Backscatter Moessbauer Spectrometer/X Ray Fluorescence analyzer (BaMS/XRF)

We have developed a four-detector research-grade backscatter Moessbauer spectrometer (BaMS) instrument with low resolution x-ray fluorescence analysis (XRF) capability. A flight-qualified instrument based on this design would be suitable for use on missions to the surfaces of solid solar-system objects (Moon, Mars, asteroids, etc.). Target specifications for the flight instrument are as follows: mass less than 500 g; volumes less than 300 cu cm; and power less than 2 W. The BaMS/XRF instrument would provide data on the oxidation state of iron and its distribution among iron-bearing mineralogies and elemental composition information. This data is a primary concern for the characterization of extraterrestrial surface materials.

Shelfer, T. D.↗
NASA NTRS1976

Determination of surface recombination velocity in heavily doped silicon

A method was developed and successfully tested for the determination of the effective surface recombination velocity of silicon layers doped by diffusion of phosphorus to a level of 10 to the 19th to 10 to the 21st per cu cm. The effective recombination velocity was obtained from the dependence of the electron-beam-induced current on the penetration of the electron beam of a scanning electron microscope. A special silicon diode was constructed which permitted the collection at the p-n junction of the carriers excited by the electron beam. This diode also permitted the study of the effects of surface preparation on the effective surface recombination velocity.

Watanabe, M.↗
NASA NTRS1971

Work function measurements by the field emission retarding potential method

Using the field emission retarding potential method true work functions have been measured for the following monocrystalline substrates: W(110), W(111), W(100), Nb(100), Ni(100), Cu(100), Ir(110) and Ir(111). The electron elastic and inelastic reflection coefficients from several of these surfaces have also been examined near zero primary beam energy.

Swanson, L. W.↗
NASA NTRS1972

Mars lower atmosphere - Some new implications.

Based on occultation data from the Mariner spacecraft, there are some preliminary indications of an apparent systematically higher surface pressure on the night side of Mars than on the day side. If confirmed by additional data currently becoming available, this apparent surface pressure difference could be attributed to several causes, including topography effects as has been assumed previously, an actual increase of pressure on the night side caused by diurnal effects, an apparent increase on the night side due to some mechanisms such as a dust layer, or an apparent lower pressure on the day side due to the existence of a low-lying electron layer. By calculating the effect of a low-lying electron layer on the combined neutral atmosphere and electron layer refractivity profile, it is found that the day side and night side surface pressures would be in agreement if a layer with maximum density of about 80,000 electrons per cu cm below 15 km altitude were present on the day side.

Michael, W. H., Jr.↗
NASA NTRS1975

The Influence of Coastal Fronts on the Movement and Dispersion of Oil Slicks

The author has identified the following significant results. LANDSAT, aircraft, and boats were used successfully to study estuarine and coastal fronts or boundaries. Fronts are a major hydrographic feature in Delaware Bay and in other estuaries. Horizontal salinity gradients of 4% in one meter and convergence velocities of the order of 0.1 m/sec were observed. Visibility improved from one meter to two meters as certain boundaries were crossed. Fronts near the mouth of the bay are associated with the tidal exchange with shelf water. The formation of fronts in the interior of the bay appears to be associated with velocity shears induced by differences in bottom topography with horizontal density difference in the deep water portion of the estuary. Surface slicks and foam collected at frontal convergence zones near boundaries were found to contain concentrations of Cr, Cu, Fe, Hg, Pb, and Zn higher by two to four orders of magnitude than concentrations in mean ocean water.

Klemas, V.↗
NASA NTRS1976

Shear strength of metal-sapphire contacts

The shear strength of polycrystalline Ag, Cu, Ni, and Fe contacts on clean (0001) sapphire has been studied in ultrahigh vacuum. Both clean metal surfaces and surfaces exposed to O2, Cl2, and C2H4 were used. The results indicate that there are two sources of strength of Al2O3-metal contacts: an intrinsic one that depends on the particular clean metal in contact with Al2O3 and an additional one due to intermediate films. The shear strength of the clean metal contacts correlated directly with the free energy of oxide formation for the lowest metal oxide, in accord with the hypothesis that a chemical bond is formed between metal cations and oxygen anions in the sapphire surface. Contacts formed by metals exposed to chlorine exhibited uniformly low shear strength indicative of van der Waals bonding between chlorinated metal surfaces and sapphire. Contacts formed by metals exposed to oxygen exhibited enhanced shear strength, in accord with the hypothesis that an intermediate oxide layer increases interfacial strength.

Pepper, S. V.↗
NASA NTRS1992

X-ray scattering measurements from thin foil X-ray mirrors

Thin foil X-ray mirrors are to be used as the reflecting elements in the telescopes of the X-ray satellites Spectrum-X-Gamma (SRG) and ASTRO-D. High resolution X-ray scattering measurements from the Au coated and dip-lacquered Al foils are presented. These were obtained from SRG mirrors positioned in a test quadrant of the telescope structure and from ASTRO-D foils held in a simple fixture. The X-ray data is compared with laser data and other surface structure data such as STM, atomic force microscopy (AFM), TEM, and electron micrography. The data obtained at Cu K-alpha(1), (8.05 keV) from all the mirrors produced on Al foils shows a scatter which limits the obtainable half-power width to above 1.5 arcmin. Mirrors based on electroformed Ni foils, however, show local regions with a factor of 4 better performance, and they are being developed for future applications.

Christensen, F. E.↗
NASA NTRS2007

Effects of Different Braze Materials and Composite Substrates on Composite/Ti Joints

An ever increasing number of applications require robust joining technologies of dissimilar materials. In this study, three types of ceramic composites (C-C, C-SiC, and SiC-SiC) were vacuum brazed to commercially pure Ti using the Cusil-ABA (63 Ag - 35.5 Cu - 1.75 Ti) active metal braze alloy. The study also compared composite specimens as-fabricated and after surface grinding/polishing. A butt-strap tensile shear strength test was used to evaluate the joined structures at room temperature, 270 and 500 C. The elevated temperatures represent possible use temperatures for some heat rejection type applications. Joint strength will be discussed in light of braze wetting and spreading properties, composite properties, and test temperature.

Morscher, Gregory N.↗