Results for “DSMC” — Page 10

NASA NTRS2016

Extension of the Viscous Collision Limiting Direct Simulation Monte Carlo Technique to Multiple Species

There are many flows fields that span a wide range of length scales where regions of both rarefied and continuum flow exist and neither direct simulation Monte Carlo (DSMC) nor computational fluid dynamics (CFD) provide the appropriate solution everywhere. Recently, a new viscous collision limited (VCL) DSMC technique was proposed to incorporate effects of physical diffusion into collision limiter calculations to make the low Knudsen number regime normally limited to CFD more tractable for an all-particle technique. This original work had been derived for a single species gas. The current work extends the VCL-DSMC technique to gases with multiple species. Similar derivations were performed to equate numerical and physical transport coefficients. However, a more rigorous treatment of determining the mixture viscosity is applied. In the original work, consideration was given to internal energy non-equilibrium, and this is also extended in the current work to chemical non-equilibrium.

Liechty, Derek S.↗

NASA NTRSDate not supplied

Validating Drag and Heating Coefficients for Hollow Reentry Objects in Continuum Flow Using a Mach 7 Ludwieg Tube

Drag and heating coefficient databases and models are crucial to destructive reentry simulation. The NASA Orbital Debris Program Office (ODPO) develops, maintains, and performs analysis with the Object Reentry Survival Analysis Tool (ORSAT), which comprises drag and heating models for free molecular, transitional, and continuum flow regimes. These models have, in the past, only included solid, convex, blunt shapes (such as boxes, spheres, and cylinders). Previous work led by ODPO includes the extension of these models to hollow cylinders and square boxes in free molecular and transitional flow using the Direct Simulation Monte Carlo (DSMC) method. Since 2019, the ODPO has continued its program of DSMC simulations and extended the project to include analyses with the NASA Data Parallel Line Relaxation (DPLR) program on hollow cylinders and boxes (with varying wall thickness-diameter ratio). In fall 2022, the ODPO began a collaboration with the University of Texas San Antonio (UTSA) to use the Mach 7 Ludwieg Tube facility to validate the model built using numerical simulations. This facility can replicate (at a scale of approximately 100:1) the conditions seen by reentering objects near typical demise altitudes. We present here the drag and heating coefficients derived from the continued DSMC simulations, the new DPLR simulations, and the 26-test series at UTSA.

Chris Ostrom↗

NASA NTRS2023

Validating Drag and Heating Coefficients for Hollow Reentry Objects in Continuum Flow Using a Mach 7 Ludwieg Tube

Drag and heating coefficient databases and models are crucial to destructive reentry simulation. The NASA Orbital Debris Program Office (ODPO) develops, maintains, and performs analysis with the Object Reentry Survival Analysis Tool (ORSAT), which comprises drag and heating models for free molecular, transitional, and continuum flow regimes. These models have, in the past, only included solid, convex, blunt shapes (such as boxes, spheres, and cylinders). Previous work led by ODPO includes the extension of these models to hollow cylinders and square boxes in free molecular and transitional flow using the Direct Simulation Monte Carlo (DSMC) method. Since 2019, the ODPO has continued its program of DSMC simulations and extended the project to include analyses with the NASA Data Parallel Line Relaxation (DPLR) program on hollow cylinders and boxes (with varying wall thickness-diameter ratio). In fall 2022, the ODPO began a collaboration with the University of Texas San Antonio (UTSA) to use the Mach 7 Ludwieg Tube facility to validate the model built using numerical simulations. This facility can replicate (at a scale of approximately 100:1) the conditions seen by reentering objects near typical demise altitudes. We present here the drag and heating coefficients derived from the continued DSMC simulations, the new DPLR simulations, and the 26-test series at UTSA.

Chris Ostrom↗

DOE OSTI2026

A lumped particle direct simulation Monte-Carlo method combined with the collisional-radiative model for simulations of non-equilibrium laser-induced plasma plumes

Collisional plasma plumes induced by laser irradiation of material targets exhibit large variations in local density as well as ionization and excitation states, making purely hydrodynamic or kinetic simulations inaccurate or infeasible. To address this challenge and capture non-equilibrium effects in laser-induced plasma plumes at arbitrary degrees of ionization, we develop a hybrid computational approach that combines the kinetic direct simulation Monte Carlo (DSMC) method with a collisional-radiative model (CRM). This ℓDSMC-CRM approach utilizes a lumped particle method to represent minor fractions of excited ions in particle-based simulations and a special coarse-graining technique for atomic spectra and photoionization rates, ensuring numerical convergence at reduced computational cost. The hybrid approach is applied to simulate spatially homogeneous relaxation as well as one- and two-dimensional expansions of plasma plumes induced by irradiation of a copper target by a nanosecond laser pulse in a vacuum or background gas. The comparison with an equilibrium model, where local Saha-Boltzmann equilibrium is enforced, shows that the non-equilibrium effects play a dominant role. The equilibrium model can fail to predict the flow structure and strongly underestimate the degree of absorption of laser radiation by the plume. The ℓDSMC-CRM approach is validated against experimental data demonstrating reasonable agreement with the experimental electron density and temperature, while the equilibrium model is found to dramatically underestimate electron density and temperature. The flexibility of the ℓDSMC-CRM approach allows for its seamless integration into existing DSMC frameworks, making it a valuable tool for high-fidelity plasma modeling in laser-material interactions, laser-based manufacturing, and beyond.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2024

Efficient particle control in systems with large density gradients

Simulations of large density gradients present a number of challenges for direct Monte Carlo methods, since they lead to too few particles in dilute regions and prohibitively many in the dense regions. Here, we propose a particle control methodology that gives the user more control of the number of particles per cell by introducing a variable weight for each particle. The proposed scheme is based on the stochastic weighted particle method, requires only small modifications to DSMC, and exactly conserves mass, momentum, and energy. In validation tests of systems with density ratios of order 102-104, we observe 101-102 times less variance in the dilute region compared to a DSMC solution with the same number of system particles, while introducing a moderate additional computational cost.

DSMC↗

NASA NTRS2017

Tortuosity Computations of Porous Materials using the Direct Simulation Monte Carlo

Low-density carbon fiber preforms, used as thermal protection systems (TPS) materials for planetary entry systems, have permeable, highly porous microstructures consisting of interlaced fibers. Internal gas transport in TPS is important in modeling the penetration of hot boundary-layer gases and the in-depth transport of pyrolysis and ablation products. The gas effective diffusion coefficient of a porous material must be known before the gas transport can be modeled in material response solvers; however, there are very little available data for rigid fibrous insulators used in heritage TPS.The tortuosity factor, which reflects the efficiency of the percolation paths, can be computed from the effective diffusion coefficient of a gas inside a porous material and is based on the micro-structure of the material. It is well known, that the tortuosity factor is a strong function of the Knudsen number. Due to the small characteristic scales of porous media used in TPS applications (typical pore size of the order of 50 micron), the transport of gases can occur in the rarefied and transitional regimes, at Knudsen numbers above 1. A proper way to model the gas dynamics at these conditions consists in solving the Boltzmann equation using particle-based methods that account for movement and collisions of atoms and molecules.In this work we adopt, for the first time, the Direct Simulation Monte Carlo (DSMC) method to compute the tortuosity factor of fibrous media in the rarefied regime. To enable realistic simulations of the actual transport of gases in the porous medium, digitized computational grids are obtained from X-ray micro-tomography imaging of real TPS materials. The SPARTA DSMC solver is used for simulations. Effective diffusion coefficients and tortuosity factors are obtained by computing the mean-square displacement of diffusing particles.We first apply the method to compute the tortuosity factors as a function of the Knudsen number for computationally designed materials such as random cylindrical fibers and packed bed of spheres with prescribed porosity. Results are compared to literature values obtained using random walk methods in the rarefied and transitional regime and a finite-volume method for the continuum regime. We then compute tortuosity factors for a real carbon fiber material with a transverse isotropic structure (FiberForm), quantifying differences between through-thickness and in-plain tortuosities at various Knudsen regimes.

Tortuosity↗

NASA NTRS2018

Numerically Simulating an Expanding Continuum Jet into a Surrounding Non-Continuum Region

A numerical technique that simulates the interaction between a continuum jet and a free-molecular, rarefied or transitional flow field is presented and applied. The technique is based on selecting a boundary between the expanding jet plume and interacting flow field defined by the Bird breakdown parameter, P. By properly choosing the boundary, the jet plume computed by computational fluid dynamics (CFD) is uncoupled from the interaction region that is simulated by direct simulation Monte Carlo (DSMC). The mechanics of uncoupling the continuum and non-continuum regions is discussed first. Also, a discussion of expanding continuum plume breakdown and the formulation of the Bird breakdown parameter is presented. To show the usefulness, examples of applying the CFD-DSMC technique are given. Many of the examples were taken from projects worked by the staff of the Aerothermodynamics Branch at the NASA Langley Research Center. These examples show a variety of applications of the technique and allow those examples not previously documented to be formally presented.

Jet interaction↗

NASA NTRSDate not supplied

Application of OpenFOAM to Plume Impingement in Space Environments

After 30 years of continuous human presence in low-earth orbit, NASA is returning to the moon and eventually will go to Mars. Travelling beyond low earth orbit requires NASA to learn how humans can live in Deep Space environments – beyond the protection of Earth’s magnetosphere and at distances from Earth that prevent a quick return in case of trouble. To this end, NASA is constructing the Lunar Gateway, an ISS-like space station to be put in orbit around the moon to act as a home base for Lunar exploration for NASA astronauts. The Gateway Lunar outpost will be built incrementally, via modules which will arrive at separate times and dock to the existing structure. The incremental addition of Gateway modules, and the docking of visiting vehicles, is achieved via a sequence of firings from the approaching body’s onboard reaction control system (RCS) thrusters to achieve the required approach trajectory. The typical hypergolic chemical RCS thrusters work by firing hot gases to produce adverse thrust and the needed change in velocity to safely finish the docking process. The exhaust gas from the RCS thrusters form plumes that expand into the vacuum of space and can impinge onto the outer surfaces of the Lunar Gateway, causing unwanted forces and moments, heat loads, sediment deposition, and in extreme cases, even surface erosion - all mechanisms that can damage the Lunar Gateway and must be minimized. Both permanent and visiting modules will have this RCS thruster exhaust impingement problem. This research aims to establish existing OpenFOAM solvers as a methodology for improving simulation techniques of rocket exhaust plume impingement in space environments. The flow structure of a plume in a space environment is complex; a plume that originates from a hypergolic chemical RCS thruster and expands into a vacuum will experience several regimes of rarefication. This range includes the continuum flow in the rocket nozzle through the fully rarefied free molecular flow further from the nozzle. The flow physics is different at these two extremes, and as such, the simulation approach for plumes is generally divided into a traditional computational fluid dynamics (CFD) simulation in and near the nozzle which is coupled to a subsequent direct simulation Monte Carlo (DSMC) simulation. At this time, the scope of this research is developing, verifying, and validating a method using existing solvers in the OpenFOAM framework for performing coupled CFD/DSMC calculations to determine the extent of plume impingement loading on generic space structures. This presentation will detail code-to-code comparisons between the hyStrath dsmcFoam+ solver, developed using OpenFOAM and available as open-source, and NASA’s in-house DSMC Analysis Code (DAC). Comparisons to several open-source publication findings using DAC [3,4] are presented, and advantages of using an OpenFOAM based solver are also discussed. The presentation concludes with a discussion of future work, and a plan for coupling the dsmcFoam+ solver with CFD simulations of chemical rocket engines for unified coupled plume simulation.

DSMC↗

NASA NTRSDate not supplied

Boundary-Layer Flow Simulations Over Ablating Woven Thermal Protection System Material

Spallation is the mechanical removal of small chunks of material gets removed typically due to high shear conditions of the flow field. This reduces the ability of the thermal protection system (TPS) material to protect the spacecraft as well as cause turbulence in the flow causing higher heating rates. In this work, we focus on the material removal through ablation and high shear flow within the boundary layer region of woven TPS material. Woven TPS (WTPS) material is the latest class of material developed by NASA, to be used within the next generation of space flights. They are complex interlocked weaves designed to create a rigid structure that is highly resistant to heat and can be easily designed and tailored for a wide variety of entry environments. Due to material removal resulting from chemical degradation, the structural integrity of TPS material is affected. Spallation occurs when this structurally compromised material is exposed to the high shear flow conditions within the boundary layer. In order to understand the spallation mechanism within WTPS material, we first perform the material removal simulations which occur primarily through oxidation to obtain the microstructure at various stages of degradation. These simulations are performed using the Porous Microstructure Analysis (PuMA) software developed at NASA Ames. The micro-structure geometry used within these simulations were generated artificially to be similar to the 3D weave architecture of MSR-EEV (Mars Sample Return - Earth Entry Vehicle). The various eroded TPS micro-structures are then subjected to the boundary layer flow conditions to obtain critical surface quantities which contribute to the structural failure mechanism such as heat flux, pressure, and shear stress. The direct simulation Monte Carlo (DSMC) methodology is used to perform these simulations in order to accurately capture the strong gradients within the high-temperature boundary layer flow over the intricate geometry of WTPS material. The boundary layer profile is directly taken from the Computational Fluid Dynamics (CFD) simulation and provided as boundary conditions to the DSMC inlet and outlet. Further, the variation of these properties as the microstructure undergoes changes due to oxidation is also investigated. Finally, these quantities are used as input in PuMA to understand the material expansion/compression and strain within the woven TPS geometry and help in developing a comprehensive spallation and structure failure model.

microstructure↗

NASA NTRSDate not supplied

Boundary-Layer Flow Simulations Over Ablating Woven Thermal Protection System Material

Spallation is the mechanical removal of small chunks of material gets removed typically due to high shear conditions of the flow field. This reduces the ability of the thermal protection system (TPS) material to protect the spacecraft as well as cause turbulence in the flow causing higher heating rates. In this work, we focus on the material removal through ablation and high shear flow within the boundary layer region of woven TPS material. Woven TPS (WTPS) material is the latest class of material developed by NASA, to be used within the next generation of space flights. They are complex interlocked weaves designed to create a rigid structure that is highly resistant to heat and can be easily designed and tailored for a wide variety of entry environments. Due to material removal resulting from chemical degradation, the structural integrity of TPS material is affected. Spallation occurs when this structurally compromised material is exposed to the high shear flow conditions within the boundary layer. In order to understand the spallation mechanism within WTPS material, we first perform the material removal simulations which occur primarily through oxidation to obtain the microstructure at various stages of degradation. These simulations are performed using the Porous Microstructure Analysis (PuMA) software developed at NASA Ames. The micro-structure geometry used within these simulations were generated artificially to be similar to the 3D weave architecture of MSR-EEV (Mars Sample Return - Earth Entry Vehicle). The various eroded TPS micro-structures are then subjected to the boundary layer flow conditions to obtain critical surface quantities which contribute to the structural failure mechanism such as heat flux, pressure, and shear stress. The direct simulation Monte Carlo (DSMC) methodology is used to perform these simulations in order to accurately capture the strong gradients within the high-temperature boundary layer flow over the intricate geometry of WTPS material. The boundary layer profile is directly taken from the Computational Fluid Dynamics (CFD) simulation and provided as boundary conditions to the DSMC inlet and outlet. Further, the variation of these properties as the microstructure undergoes changes due to oxidation is also investigated. Finally, these quantities are used as input in PuMA to understand the material expansion/compression and strain within the woven TPS geometry and help in developing a comprehensive spallation and structure failure model.

microstructure↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Computational Investigation of Oxidative Etch Pitting in FiberForm and Its Impact on Material Properties

Oxidation-driven carbon erosion does not occur uniformly but rather through the development of localized etch pits at active surface sites. These active sites form due to atomic defects on the carbon surface, making them significantly more reactive than the surrounding, non-defective areas. As a result, these sites are the first to react during ablation, leading to their removal. This process creates new defects in neighboring atoms, increasing their reactivity and causing localized carbon removal around these active sites. In this way, the highly reactive defective areas serve as nucleation points for the formation and growth of etch pits, which can have adverse effects on structural integrity of FiberForm. To better understand how these etch pits impact the material properties of carbon fiber microstructures, we have developed a new capability within the direct simulation Monte Carlo (DSMC) framework to capture the etch pit formation process. This capability, integrated into the DSMC code SPARTA (Stochastic Parallel Rarefied-gas Time-accurate Analyzer), models material removal in the presence of active sites, leading to the formation of etch pits. The current work focuses on studying the effects of these etch pits on the material properties of FiberForm, a widely used base material in thermal protection systems (TPS). The microstructure of virgin FiberForm, obtained via X-ray microtomography, is imported into SPARTA to generate the ablated geometries with etch pits. These modified microstructures are then analyzed using the Porous Microstructure Analysis (PuMA) software to compute various material properties, including elasticity, thermal conductivity, and permeability. We investigate the variation of these properties due to the complex surface topology changes caused by etch pit formation. Additionally, we compare the effects of pitting with the conventional model of shrinking fibers, traditionally used to simulate the ablation of carbon structures. Significant differences emerge between the two approaches. Consequently, this physically realistic model of material removal through etch pit formation offers improved accuracy in predicting the degradation of carbon-based TPS during oxidation. It also provides insights into other mechanisms, such as spallation, where chunks of material are removed into the flow due to etch pit growth. Ultimately, this model enhances our understanding of failure modes in these materials during ablation.

PuMA↗

DOE OSTI2020

A velocity space hybridization-based Boltzmann equation solver

In the present research, a new method for simulation of rarefied gas flows is proposed, a velocity-space hybrid of both a DSMC representation of particles and a discrete velocity quasi-particle representation of the distribution function. The hybridization scheme is discussed in detail, and is numerically verified for two test-cases: the BKW relaxation problem and a stationary Maxwellian distribution. It is demonstrated that such a velocity-space hybridization can provide computational benefits when compared to a pure discrete velocity method or pure DSMC approach, while retaining some of the more attractive properties of discrete velocity methods. Further possible improvements to the velocity-space hybrid approach are discussed.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2024

An improved stochastic weighted particle method for boundary driven flows

Here, the stochastic weighted particle method (SWPM) is a generalization of the Direct Simulation Monte Carlo (DSMC) method where particle weights are variable and dynamic. SWPM is backed by a strong theoretical foundation but has not been critically evaluated for problems of practical interest. A thorough assessment of SWPM for boundary-driven flows reveals significant numerical artifacts near the boundary, notably a diverging heat flux. To correct the boundary heat flux, two modifications to SWPM are proposed: separated grouping and a spatially-dependent weight transfer function. To gauge the relative efficiency of SWPM in comparison to DSMC, a high-Mach-number wheel flow which forms a strong density gradient is also simulated.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2023

Near-continuum, hypersonic oxygen flow over a double cone simulated by direct simulation Monte Carlo informed from quantum chemistry

A large-scale, fully resolved direct simulation Monte Carlo (DSMC) computation of a non-equilibrium, reactive flow of pure oxygen over a double cone is presented. Under the simulated near-continuum conditions, the computational demands are shown to be significant because of the wide range of length scales that must be resolved. Therefore, robust grid adaption capabilities and efficient parallelization of the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code that is utilized in this work are essential. The thermochemical and transport collision models were selected for efficiency and simplicity. First-principles data, obtained from the highly accurate direct molecular simulation method, were used to inform the collision models’ parameters. Importantly, because SPARTA implements molecular collision models using collision-specific energies, the resulting macroscopic relaxation rates were evaluated a posteriori via zero-dimensional heat bath simulations. The comparisons of surface properties, namely heat flux and pressure, show very close agreement with previous computational fluid dynamics (CFD) results. Differences with the measurements were found to be similar to the CFD simulations. The unresolved discrepancy with the measurements could be due to inconsistent free stream conditions with the actual experimental data or missing physical phenomena altogether, for example atomic and molecular oxygen electronically excited states, three-dimensional effects, or more complex gas–surface interactions. As shown in this work, the advantages of obtaining a DSMC particle solution for these flows reside in the method's ability to be directly informed from first principles and to seamlessly describe internal energy non-equilibrium for all modes. With the advent of exascale computing and beyond, particle methods will be an increasingly important tool to verify the validity of physical assumptions in reduced-order models via fully resolved, experimental-scale simulations, down to the level of molecular-level distributions.

Mechanics↗