Results for “Deep Space Network DSN” — Page 10

NASA NTRS2016

Comparison of Atmospheric Delay Statistics from Deep Space Network Arrays and Nearby Test Interferometers

Several techniques have been explored and demonstrated that allow for greater data return on space-to-ground links. Among these techniques, arraying several smaller diameter dish antennas together is one method used in several arenas. These arrays can achieve larger effective area and gain than are available from a single larger antenna. This technique is routinely used by the NASA Deep Space Network (DSN) at 8.4 GHz where the incoming signals are much weaker than those experienced by the near-Earth satellite community. When considering arraying at much higher frequencies such as 32 GHz deep-space Ka-band, the phase alignment of the individual antenna signals is significantly disrupted by atmospheric turbulence. Since 2012, several downlink array demonstrations have been conducted using 32 GHz carrier signals emitted by the deep space probes Cassini and Kepler. Site test interferometers (STIs) that receive signals from geostationary satellites have been deployed at all three DSN tracking complexes for long-term monitoring of atmospheric delay fluctuations. In a previous DSN array demonstration study involving the Cassini spacecraft, it was shown that statistics of the adjusted STI phase fluctuations matched the statistics of concurrent array demonstration phase fluctuations. These adjustments accounted for differences in antenna separation, elevation angle and spacecraft frequencies. The STI antenna separations were about 200 m and the DSN antenna separations were about 300 m. These adjustments made use of the thick-layer turbulence model that was applicable to the Goldstone desert climate during the summer months for which the data were acquired. In this paper, we report on the results of additional array demonstrations involving the Kepler spacecraft and compare the adjusted STI phase fluctuations with those seen by a nearby two-element array of 34 m diameter antennas tracking Kepler’s 32 GHz signal at the Goldstone, California and Madrid, Spain DSN sites. We also discuss results from a demonstration using an array over a longer 12.5 km baseline. The Cassini and Kepler array demonstrations were found to validate the long term statistics acquired from several years of STI data as well as the models used to adjust the statistics for the conditions of an array. These statistics represent reliable estimates of the phase fluctuations that would be seen by an array tracking a deep space signal after applying appropriate adjustments for a given array configuration, elevation angle profile and observing frequency.

Morabito, David D.↗

NASA NTRS1988

A long constraint length VLSI Viterbi decoder for the DSN

A Viterbi decoder, capable of decoding convolutional codes with constraint lengths up to 15, is under development for the Deep Space Network (DSN). The objective is to complete a prototype of this decoder by late 1990, and demonstrate its performance using the (15, 1/4) encoder in Galileo. The decoder is expected to provide 1 to 2 dB improvement in bit SNR, compared to the present (7, 1/2) code and existing Maximum Likelihood Convolutional Decoder (MCD). The decoder will be fully programmable for any code up to constraint length 15, and code rate 1/2 to 1/6. The decoder architecture and top-level design are described.

Statman, J. I.↗

NASA NTRS2014

Iris Transponder-Communications and Navigation for Deep Space

The Jet Propulsion Laboratory has developed the Iris CubeSat compatible deep space transponder for INSPIRE, the first CubeSat to deep space. Iris is 0.4 U, 0.4 kg, consumes 12.8 W, and interoperates with NASA's Deep Space Network (DSN) on X-Band frequencies (7.2 GHz uplink, 8.4 GHz downlink) for command, telemetry, and navigation. This talk discusses the Iris for INSPIRE, it's features and requirements; future developments and improvements underway; deep space and proximity operations applications for Iris; high rate earth orbit variants; and ground requirements, such as are implemented in the DSN, for deep space operations.

cubesat↗

NASA NTRS1999

Deep Space Network Revitalization - Operations For the 21st Century

The National Aeronautics and Space Administration (NASA) supports unmanned space missions through a Deep Space Network (DSN) that is developed and operated by the Jet Propulsion Labortory (JPL) and its subcontractors.

Network↗

NASA NTRS1991

Space Transportation System (STS): Emergency support

The DSN (Deep Space Network) mission support requirements for emergency support of the Space Transportation System (STS) are summarized. Coverage would be provided by the DSN during emergencies that would prevent communications between the shuttle and the White Sands TDRSS receiving station. The DSN support requirements are defined through the presentation of tables and narratives describing the spacecraft flight profile; DSN support coverage; frequency assignments; support parameters for telemetry, command and support systems; and tracking support responsibility.

Janoski, T.↗

NASA NTRS2004

Readout of DSN Monitor Data

DSN Monitor Data Reader is a computer program that, as its name suggests, reads file of monitor data from the Deep Space Network (DSN). The monitor data constitute information on the status and performance of tracking, telemetry, command, and pointing equipment at the DSN antennas. The DSN has recently introduced a new, more advanced monitor data format, denoted 0158-Mon, that is based on the standard formatted data unit (SFDU) and compressed header data objects (CHDO) of the Consultative Committee for Space Data Systems (CCSDS). The 0158-Mon data format is a very flexible generic format that provides for specific variable-length formats and for self-identifying parameters that obviate the proprietary NASA Communications (NASCOM) bit-packed formats of the past. The monitor data SFDUs are also encapsulated in Standard DSN Blocks and routed to DSN customers for processing at their local mission control centers. This program helps a DSN customer to read and parse the monitor data to assess the statuses of the DSN stations in support of spacecraft flight operations.

Levister, Katherine↗

NASA NTRS1993

The Telecommunications and Data Acquisition Report

This quarterly publication provides archival reports on developments in programs managed by JPL's Office of Telecommunications and Data Acquisition (TDA). In space communications, radio navigation, radio science, and ground-based radio and radar astronomy, it reports on activities of the Deep Space Network (DSN) in planning, supporting research and technology, implementation, and operations. Also included are standards activity at JPL for space data and information systems and reimbursable DSN work performed for other space agencies through NASA. The papers included in this document cover satellite tracking and ground-based navigation, spacecraft-ground communications, and optical communication systems for the Deep Space Network.

Yuen, Joseph H.↗

NASA NTRS1990

Initial results on fault diagnosis of DSN antenna control assemblies using pattern recognition techniques

Initial results obtained from an investigation using pattern recognition techniques for identifying fault modes in the Deep Space Network (DSN) 70 m antenna control loops are described. The overall background to the problem is described, the motivation and potential benefits of this approach are outlined. In particular, an experiment is described in which fault modes were introduced into a state-space simulation of the antenna control loops. By training a multilayer feed-forward neural network on the simulated sensor output, classification rates of over 95 percent were achieved with a false alarm rate of zero on unseen tests data. It concludes that although the neural classifier has certain practical limitations at present, it also has considerable potential for problems of this nature.

Smyth, P.↗

NASA NTRS2012

Automated Performance Characterization of DSN System Frequency Stability Using Spacecraft Tracking Data

This software provides an automated capability to measure and qualify the frequency stability performance of the Deep Space Network (DSN) ground system, using daily spacecraft tracking data. The results help to verify if the DSN performance is meeting its specification, therefore ensuring commitments to flight missions; in particular, the radio science investigations. The rich set of data also helps the DSN Operations and Maintenance team to identify the trends and patterns, allowing them to identify the antennas of lower performance and implement corrective action in a timely manner. Unlike the traditional approach where the performance can only be obtained from special calibration sessions that are both time-consuming and require manual setup, the new method taps into the daily spacecraft tracking data. This new approach significantly increases the amount of data available for analysis, roughly by two orders of magnitude, making it possible to conduct trend analysis with good confidence. The software is built with automation in mind for end-to-end processing. From the inputs gathering to computation analysis and later data visualization of the results, all steps are done automatically, making the data production at near zero cost. This allows the limited engineering resource to focus on high-level assessment and to follow up with the exceptions/deviations. To make it possible to process the continual stream of daily incoming data without much effort, and to understand the results quickly, the processing needs to be automated and the data summarized at a high level. Special attention needs to be given to data gathering, input validation, handling anomalous conditions, computation, and presenting the results in a visual form that makes it easy to spot items of exception/ deviation so that further analysis can be directed and corrective actions followed.

Pham, Timothy T.↗

NASA NTRS2012

Automated Performance Characterization of DSN System Frequency Stability Using Spacecraft Tracking Data

This software provides an automated capability to measure and qualify the frequency stability performance of the Deep Space Network (DSN) ground system, using daily spacecraft tracking data. The results help to verify if the DSN performance is meeting its specification, therefore ensuring commitments to flight missions; in particular, the radio science investigations. The rich set of data also helps the DSN Operations and Maintenance team to identify the trends and patterns, allowing them to identify the antennas of lower performance and implement corrective action in a timely manner. Unlike the traditional approach where the performance can only be obtained from special calibration sessions that are both time-consuming and require manual setup, the new method taps into the daily spacecraft tracking data. This new approach significantly increases the amount of data available for analysis, roughly by two orders of magnitude, making it possible to conduct trend analysis with good confidence. The software is built with automation in mind for end-to-end processing. From the inputs gathering to computation analysis and later data visualization of the results, all steps are done automatically, making the data production at near zero cost. This allows the limited engineering resource to focus on high-level assessment and to follow up with the exceptions/deviations. To make it possible to process the continual stream of daily incoming data without much effort, and to understand the results quickly, the processing needs to be automated and the data summarized at a high level. Special attention needs to be given to data gathering, input validation, handling anomalous conditions, computation, and presenting the results in a visual form that makes it easy to spot items of exception/deviation so that further analysis can be directed and corrective actions followed.

Pham, Timothy T.↗

NASA NTRS2006

CFDP Performance over Weather-Dependent Ka-Band Channel

This study presents an analysis of the delay performance of the CCSDS File Delivery Protocol (CFDP) over weather-dependent Ka-band channel. The Ka-band channel condition is determined by the strength of the atmospheric noise temperature, which is weather dependent. Noise temperature data collected from the Deep Space Network (DSN) Madrid site is used to characterize the correlations between good and bad channel states in a two-state Markov model. Specifically, the probability distribution of file delivery latency using the CFDP deferred Negative Acknowledgement (NAK) mode is derived and quantified. Deep space communication scenarios with different file sizes and bit error rates (BERs) are studied and compared. Furthermore, we also examine the sensitivity of our analysis with respect to different data sampling methods. Our analysis shows that while the weather-dependent channel only results in fairly small increases in the average number of CFDP retransmissions required, the maximum number of transmissions required to complete 99 percentile, on the other hand, is significantly larger for the weather-dependent channel due to the significant correlation of poor weather states.

weather↗

NASA NTRS2006

CFDP Performance over Weather-dependent Ka-band Channel

This study presents an analysis of the delay performance of the CCSDS File Delivery Protocol (CFDP) over weather-dependent Ka-band channel. The Ka-band channel condition is determined by the strength of the atmospheric noise temperature, which is weather dependent. Noise temperature data collected from the Deep Space Network (DSN) Madrid site is used to characterize the correlations between good and bad channel states in a two-state Markov model. Specifically, the probability distribution of file delivery latency using the CFDP deferred Negative Acknowledgement (NAK) mode is derived and quantified. Deep space communication scenarios with different file sizes and bit error rates (BERs) are studied and compared. Furthermore, we also examine the sensitivity of our analysis with respect to different data sampling methods. Our analysis shows that while the weather-dependent channel only results in fairly small increases in the average number of CFDP retransmissions required, the maximum number of transmissions required to complete 99 percentile, on the other hand, is significantly larger for the weather-dependent channel due to the significant correlation of poor weather states.

deep space communications↗

NASA NTRS2006

Scheduling with Automatic Resolution of Conflicts

DSN Requirement Scheduler is a computer program that automatically schedules, reschedules, and resolves conflicts for allocations of resources of NASA s Deep Space Network (DSN) on the basis of ever-changing project requirements for DSN services. As used here, resources signifies, primarily, DSN antennas, ancillary equipment, and times during which they are available. Examples of project-required DSN services include arraying, segmentation, very-long-baseline interferometry, and multiple spacecraft per aperture. Requirements can include periodic reservations of specific or optional resources during specific time intervals or within ranges specified in terms of starting times and durations. This program is built on the Automated Scheduling and Planning Environment (ASPEN) software system (aspects of which have been described in previous NASA Tech Briefs articles), with customization to reflect requirements and constraints involved in allocation of DSN resources. Unlike prior DSN-resource- scheduling programs that make single passes through the requirements and require human intervention to resolve conflicts, this program makes repeated passes in a continuing search for all possible allocations, provides a best-effort solution at any time, and presents alternative solutions among which users can choose.

Clement, Bradley↗

NASA NTRS2017

DSN Wide Area Network Architecture, Capacity and Performance

This paper discusses the architecture of the wide area network that connects key communications facilities within the National Aeronautic and Space Administration (NASA) Deep Space Network (DSN). Several considerations are given to the design of this wide area network to ensure a timely, reliable, and secure data delivery between the mission users and their spacecraft. The network star configuration simplifies data delivery to users and minimizes operational cost. The dual-path connections maximize the system reliability, with geographical diversity in data routing to avoid single point of failure. Data encryption enhances the protection of mission users’ data. The system bandwidth is determined by balancing the needs to minimize the operating bandwidth cost and to have sufficient bandwidth to be able to deliver data to all users within the required. The DSN uses a class base weighted fair queuing (CBWFQ) method in its data delivery. This scheme guarantees a minimum bandwidth to each class of users and allows users to also access any unused bandwidth by other groups. The paper will also show performance of system reliability and bandwidth margin.

Liao, Jason↗

NASA NTRS2002

Major technological innovations introduced in the large antennas of the Deep Space Network

The NASA Deep Space Network (DSN) is the largest and most sensitive scientific, telecommunications and radio navigation network in the world. Its principal responsibilities are to provide communications, tracking, and science services to most of the world's spacecraft that travel beyond low Earth orbit. The network consists of three Deep Space Communications Complexes. Each of the three complexes consists of multiple large antennas equipped with ultra sensitive receiving systems. A centralized Signal Processing Center (SPC) remotely controls the antennas, generates and transmits spacecraft commands, and receives and processes the spacecraft telemetry.

large antennas beam waveguide dual reflector shapi↗

NASA NTRSDate not supplied

A Technical Overview of the Mission Engagement Onboarding Process Managed by the Mission Engagement Working Group (MEWG)

NASA's intricate network, encompassing the Near Space Network (NSN) and Deep Space Network (DSN), plays a pivotal role in supporting an array of space missions. These range from those in Low Earth Orbit (LEO) and Geosynchronous Orbit (GEO), to the more distant Cislunar and Deep Space endeavors. To manage the vast communications needs, we utilize multiple ground stations globally, coupled with the Tracking and Data Relay Satellite System (TDRSS). The Mission Engagement Working Group (MEWG), within the Commercialization, Innovation, and Synergies (CIS) division, stands as the primary gateway for all Space Communications and Network (SCaN) communication and navigation requests. This includes not only NASA's internal missions but also extends to other governmental agencies and commercial sector endeavors. How does the MEWG Process Work? - Initial Contact : Clients initiate their interaction with the NSN by submitting their service requirements through a dedicated online portal. - Preliminary Assessment by MEWG: Upon submission, MEWG embarks on a primary screening of the request. This involves evaluating the client's identity and the foundational concept of their mission. - Detailed Analysis by the NSN Team: Parallelly, the NSN team conducts a comprehensive review of the service request. This often necessitates additional clarification from the requester, ensuring that the final assessment is both thorough and accurate. - Coordination & Streamlining: MEWG's overarching objective is to effectively log, classify, orchestrate, and guarantee that pertinent actions are delegated based on initial client interactions. Acting as the central hub for these primary contacts, MEWG ensures that each request is sufficiently detailed for an in-depth evaluation. - Feedback & Remediation: If a request is deemed unsuitable or lacking, MEWG doesn't merely reject it. Instead, the team discerns the reasons for the inadequacy and suggests potential rectification strategies. This approach ensures that feedback delivered to clients is precise, prompt, constructive, and actionable. Conclusion: This plenary presentation will detail the efforts of the MEWG resulting in a greatly streamlined and refined onboarding process for space communication Direct-To-Earth (DTE) and Space Relay (SR) support requests. By centralizing the preliminary interactions and assessments, we've reduced the complexity for clients, ensuring they engage with a singular, efficient, and responsive point of contact. This initiative, we believe, fortifies NASA's commitment to fostering effective and synergistic collaborations with its partners.

Devin L Bitner↗

NASA NTRSDate not supplied

A Technical Overview of the Mission Engagement Onboarding Process Managed by the Mission Engagement Working Group (MEWG)

NASA's intricate network, encompassing the Near Space Network (NSN) and Deep Space Network (DSN), plays a pivotal role in supporting an array of space missions. These range from those in Low Earth Orbit (LEO) and Geosynchronous Orbit (GEO), to the more distant Cislunar and Deep Space endeavors. To manage the vast communications needs, we utilize multiple ground stations globally, coupled with the Tracking and Data Relay Satellite System (TDRSS). The Mission Engagement Working Group (MEWG), within the Commercialization, Innovation, and Synergies (CIS) division, stands as the primary gateway for all Space Communications and Network (SCaN) communication and navigation requests. This includes not only NASA's internal missions but also extends to other governmental agencies and commercial sector endeavors. How does the MEWG Process Work? - Initial Contact : Clients initiate their interaction with the NSN by submitting their service requirements through a dedicated online portal. - Preliminary Assessment by MEWG: Upon submission, MEWG embarks on a primary screening of the request. This involves evaluating the client's identity and the foundational concept of their mission. - Detailed Analysis by the NSN Team: Parallelly, the NSN team conducts a comprehensive review of the service request. This often necessitates additional clarification from the requester, ensuring that the final assessment is both thorough and accurate. - Coordination & Streamlining: MEWG's overarching objective is to effectively log, classify, orchestrate, and guarantee that pertinent actions are delegated based on initial client interactions. Acting as the central hub for these primary contacts, MEWG ensures that each request is sufficiently detailed for an in-depth evaluation. - Feedback & Remediation: If a request is deemed unsuitable or lacking, MEWG doesn't merely reject it. Instead, the team discerns the reasons for the inadequacy and suggests potential rectification strategies. This approach ensures that feedback delivered to clients is precise, prompt, constructive, and actionable. Conclusion: This plenary presentation will detail the efforts of the MEWG resulting in a greatly streamlined and refined onboarding process for space communication Direct-To-Earth (DTE) and Space Relay (SR) support requests. By centralizing the preliminary interactions and assessments, we've reduced the complexity for clients, ensuring they engage with a singular, efficient, and responsive point of contact. This initiative, we believe, fortifies NASA's commitment to fostering effective and synergistic collaborations with its partners.

Devin Bitner↗

NASA NTRS1993

FASTER - A tool for DSN forecasting and scheduling

FASTER (Forecasting And Scheduling Tool for Earth-based Resources) is a suite of tools designed for forecasting and scheduling JPL's Deep Space Network (DSN). The DSN is a set of antennas and other associated resources that must be scheduled for satellite communications, astronomy, maintenance, and testing. FASTER consists of MS-Windows based programs that replace two existing programs (RALPH and PC4CAST). FASTER was designed to be more flexible, maintainable, and user friendly. FASTER makes heavy use of commercial software to allow for customization by users. FASTER implements scheduling as a two pass process: the first pass calculates a predictive profile of resource utilization; the second pass uses this information to calculate a cost function used in a dynamic programming optimization step. This information allows the scheduler to 'look ahead' at activities that are not as yet scheduled. FASTER has succeeded in allowing wider access to data and tools, reducing the amount of effort expended and increasing the quality of analysis.

Werntz, David↗