Search NASA⌕ Search

SEARCH · Search NASA

Results for “Desorption”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Isotherm measurements of high-pressure metal hydrides for hydrogen compressors

Hydrogen absorption and desorption isotherms have been measured for several metal hydride alloys identified as possible candidates in the high-pressure (i.e. >80 MPa) stage of a two-stage hydrogen compressor. The isotherms were obtained using two independent Sieverts volumetric test systems built specifically for measuring hydrogen absorption and desorption parameters from 0.10 to 100 MPa. The results obtained enabled us to identify the alloy Ti 0.8 Zr 0.2 Fe 1.6 V 0.4 as the most viable of the candidates investigated for use in the high-pressure stage of a prototype two-stage 80+ MPa compressor, as it produced the highest desorption pressures at moderate temperatures. Issues and challenges in determining reliable isotherms at pressures >50 MPa are also described.

08 HYDROGEN↗
DOE OSTI2026

The ionomer as an oxygen evolution reaction promoter: piperidinium’s impact on mechanistic pathways on NiO, IrO 2 , and Fe–NiO

The commercial viability of anion exchange membrane (AEM) electrolysis requires optimization of various stack components, with specific catalyst-ionomer combinations often yielding higher current densities, lowered Tafel slopes, and improved mass activity. In this joint theoretical-experimental study, theoretical calculations detail the impact of Versogen’s piperidinium functional group on the complex, kinetically limiting oxygen evolution reaction, finding that the functional group can act as a promoter of specific steps (O*/O 2 * formation; H 2 O/O 2 desorption with reaction enthalpies ranging between 0.2–0.6 eV at higher coverages of O x H y intermediates) on NiO and NiFeO x catalysts. In particular, Fe sites on the NiFeO x catalyst facilitate concerted mechanisms of O*/O 2 * formation and H 2 O desorption with a low enthalpy of 0.5 eV; O 2 desorption alone requires only 0.3 eV. In contrast, Versogen-IrO 2 results in stronger Ir–O bonds, where the enthalpies for bond breaking (Ir–OH 2 and Ir–O 2 ) are considerably higher (1.4 eV and 1.6 eV, respectively). Rotating disk electrode studies utilized commercially available NiO and IrO 2 and synthesized 7.5 wt % Fe in NiFeO x catalysts in combination with Versogen, a common AEM ionomer, and Nafion, an alternative binder. Electrochemical testing validated the impact of these mechanistic changes on ionomer-catalyst combinations, finding that Versogen particularly activates NiO and NiFeO x compared to IrO 2 . Following a 13.5 h hold at 1.8 V, mass activities and Tafel slopes improved to 34 ± 13 A g −1 and 79 ± 2 mV dec −1 (NiO) and 82 ± 4.9 A g −1 and 72 ± 2 mV dec −1 (NiFeO x ). In contrast, Versogen-IrO 2 only reached 17 ± 2.9 A g −1 and 81 ± 3 mV dec −1 . Optimization of the ionomer-catalyst can yield significant increases in performance from initial activity and after an electrochemical conditioning procedure: this enhancement to the mass activity resulted in a 200.9 ± 106.1% improvement for Versogen-NiFeO x and 1284.2 ± 260.5% for Versogen-NiO. In contrast, Nafion-NiFeO x and -NiO offered moderate improvements of 39.1 ± 30.5% and 120.9 ± 59.1%, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Perovskite Sorbent Oxygen Separation Modeling with MFiX

This document chronicles the development and implementation of computational kinetic rate models that capture absorption and desorption characteristics of the National Energy Technology Laboratory (NETL) developed perovskite, Sr 1-x Ca x FeO 3-δ . Two paths to create accurate kinetic rates were followed: (1) an isothermal rate approach where thermogravimetric (TGA) data are recast as oxygen capacities through a pseudo-second order Lagergren equation (He et al., 2009); and (2) a more traditional Arrhenius approach where experimental data are fit with a power law model to derive associate activation energies (Bulfin et al., 2020a). For reference, the mathematics and associate experimental strategies that support these derivations are included in this report. In addition, computational fluid dynamics (CFD) models were developed to utilize both kinetic rate formulations and applied to simulate oxygen uptake and release in small scale scenarios. The program Multiphase Flow with interphase eXchanges (MFiX) was used to create: (1) discrete element method (DEM) simulations of a single tube of granular perovskite experiencing isothermal O 2 -absorption; and desorption and (2) two-fluid-model (TFM) non-isothermal simulations of perovskite O 2 -absorption and desorption tubes that share a wall. Conjugate heat transfer between steel walled tubes and the perovskite bed were managed with user-defined functions. As the project moves to simulating larger scale devices that will require more robust conjugate heat transfer methods, developed kinetic rates and associate methodologies have been recast for use in the ANSYS Fluent CFD program.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Membrane Adsorbents Comprising Self-Assembled Inorganic Nanocages (SINCs) for Super-fast Direct Air Capture Enabled by Passive Cooling

The objectives of the proposed project were to develop highly porous membrane adsorbents comprising CO 2 -philic polymers and self-assembled inorganic nanocages (SINCs) for rapid temperature swing adsorption using electricity-free solar heating and radiative cooling, enabling an economically viable approach for direct air capture (DAC). Our core technical activities combine three key innovations. (1) Highly porous flat-sheet membrane adsorbents contain CO 2 -philic amines that can be easily produced using a phase inversion method. (2) CO 2 -philic SINCs can be easily dispersed in the polymers with great stability (compared with the metal-organic frameworks or MOFs). (3) The adsorption and desorption are integrated with solar heating and radiative cooling for rapid continuous operation, in contrast to traditional long-cycle separate operation. The membrane adsorbents containing amines, polymers, and SINCs were produced using a one-step industrial process. The porous membranes coupled with porous SINCs offer low resistance for gas flow and fast CO 2 sorption/desorption cycles, while the incorporation of the additional amine groups provides high CO 2 sorption capacity. The key achievements are summarized below. (1) Membrane adsorbents with high PEI loading (>40%), high porosity of >80%, and low gasflow resistance were prepared in one step using commercially available, low-cost materials. (2) Membrane adsorbents based on Solupor and PEI show CO 2 sorption capacity of >1.5 mmol/g using air containing 400 ppm at a relative humidity of 15%. (3) Effect of the adsorbent compositions (such as PEI type, PEI content, SINC content, porosity) on the CO 2 sorption was systematically investigated. (4) Effect of the processing conditions (such as CO 2 content, temperature, and relative humidity) on the CO 2 sorption was systematically investigated; (5) The stability of the membrane adsorption against many cycles of sorption and desorption was studied. The higher molecular weight of PEI (PEI25k) shows better stability than PEI800. (6) Advanced materials with radiative cooling were developed, which can decrease the temperature by 5-7 °C compared to the ambient temperature. (7) Preliminary techno-economic analysis shows that our process may achieve a capture cost of $1,343/tonne CO 2 with a total OPEX cost of $1,112/tonne CO 2 . The adsorbent replacement cost accounted for 52% of the total OPEX cost. Membrane adsorbents with lower costs and longer operation life can significantly decrease the cost. The proposed project directly addresses the requirement of DE-FOA-0002188, i.e., novel materials with CO 2 adsorption capacity for direct air capture with integrated solar heating and radiative cooling to reduce the cost of the DAC. Our future work will focus on the development of low-cost adsorbents that can be stable at the sorption and desorption conditions for long term.

14 SOLAR ENERGY↗
DOE OSTI2024

Bench-Scale Development of a Novel Direct Air Capture Technology Using High-Capacity Structured Sorbents

The work performed under this project has resulted into development of a DAC technology utilizing a structured sorbent to capture CO 2 from ambient air with a key innovation of direct Joule heating of the sorbent for CO 2 desorption. A working SMA, fully integrated with an electrically resistive heating layer, high surface area support, and high CO 2 capacity sorbent coated onto a commercial ceramic monolithic substrate, was successfully developed and demonstrated over >200 adsorption-desorption cycles in a high-fidelity bench test unit directly using ambient air. A cordierite-based monolith was selected as a substrate owing to its high surface area, low bulk density, low heat capacity, and commercial availability. Reaction kinetics study conducted during this project led to development of a promoter for the base Na 2 CO 3 sorbent that could be incorporated into the sorbent to enhance to achieve higher CO 2 adsorption/desorption rates, greater working capacity, and reduced regeneration temperature. An accelerated aging study was conducted in a TGA to determine sorbent stability and no degradation in the sorbent performance was observed even after 250 adsorption-desorption cycles. An electrically resistive heating layer was developed with tunable electrical properties. The heating layer was coated onto the selected cordierite substrate. Aging studies performed showed the electrical properties and heating performance was stable after 500 heating and cooling cycles. The collective findings on the selected cordierite substrate, robust heating layer, promoter and sorbent selection were used to synthesize a full, 6”x6” SMA for bench-scale testing. The bench-scale DAC system was constructed to test full size SMAs using real ambient air for adsorption and joule heating for regeneration. After completing shakedown and commissioning of the 1 kg/day of CO 2 capacity DAC bench unit, an extended operation was performed to complete over 230 cycles with the full size SMA. This testing showed no observable degradation in sorbent performance. A detailed process model, TEA and LCA were developed for a conceptual 100,000 TPY CO 2 removal DAC facility. The LCA results show the net CO 2 e emissions from the DAC system are highly dependent on the electricity source. All other factors, including SMA manufacturing, materials for facility enclosure, etc., are minor cost contributors compared to the energy consumption required for CO 2 removal. With the successful development and validation of the SMA for the sustained performance for CO 2 removal from ambient air with joule heated regeneration in this project, a fully integrated 1 TPY bench-scale DAC system is currently in development with the support of DOE/FECM (DE-FE0032243). The project objective is to demonstrate the engineering design of the DAC system to produce a continuous, high purity CO 2 stream from ambient air. This project will address and validate key engineering features of the DAC system including the gas sealing mechanism and panels, enclosure and air contactor design, and automation sequence to achieve continuous CO 2 production.

42 ENGINEERING↗
DOE OSTI2024

Ultrafast Surface Phosphor Thermometry for Pulsed-power and Hostile Environments

Modern concepts for next generation pulsed power (NGPP) are slated to deliver up to ten times the energy of Z today. An increase of this magnitude is concerning insofar that Z currently exhibits sizable amounts of inner magnetically insulated transmission line (MITL) loss current on the order of 5-10%. Loss phenomenon in these systems are complex and electrode heating and subsequent thermal desorption are a leading cause. Rapid heat-driven thermal desorption of contaminants scales as the square of the current. Therefore, even a modest doubling of drive current would yield an ~ 4X in non-linear surface electrode heating, quickening thermal desorption-based current loss. Exacerbating these physics is a current inability to measure ultra fast heating rates (>20°C/ns), which are paramount to benchmarking and code validation critical to NGPP design – as an empirical approach is not viable. Therefore, Ultrafast Photoluminescent Surface Heating Optical Thermometry (UP-SHOT) was developed as a new diagnostic for measurement of GHz-scale electrode heating. The discovery of UP-SHOT leveraged expertise in Engineering Science, Material Science, Pulsed-Power, and the Center for Integrated Nanotechnologies. This report includes information on: 1) The preparation of zinc oxide (ZnO) films, characterization, post-deposition treatments 2) Time-resolved photoluminescence at elevated temperatures and thermographic sensitivity

36 MATERIALS SCIENCE↗
DOE OSTI2024

Preparation and Characterization of Materials for Low- to Intermediate-Temperature CO2 Adsorption

Global carbon dioxide emissions are rising and the use of fossil fuels in several sectors are the leading causes. As global population and economies continue to grow significantly, the most practical method of lowering such emissions is to capture CO2. Although other technologies are more developed, adsorption is very promising and has attracted much attention. To ensure this technology’s success, it is essential to have suitable CO2 adsorbent materials. In this work, several new hydrotalcites (HTs) with different initial concentrations of ion precursors were prepared for the first time by the co-precipitation method—it was possible to verify that the ion concentrations influence the characteristics of the materials. The prepared HTs were characterized by thermogravimetric analysis (TG), X-Ray diffraction (XRD), surface area measurements and temperature-programmed desorption of CO2 (TPD-CO2) to relate their CO2 capture capacity to their physicochemical properties; the CO2 adsorption equilibrium isotherms were determined at 35 and 300 °C for the prepared samples, as well as for some commercial materials: magnesium oxide, calcium oxide, aluminium oxide and Zeolite 13X. After determining which materials present the best CO2 adsorption capacity, these were submitted to adsorption-desorption cycles to study their stability. The main objective of the work was to prepare and study different CO2 adsorbents for processes that are carried out at low and intermediate temperatures. From the experimental results, it was possible to conclude that the Zeolite 13X showed the best capacity at 35 °C, 3.38 mmol·g−1 (@ pCO2 = 1 bar), and a prepared calcined HT (c-HT2) was the best at 300 °C, 0.97 mmol·g−1 (@ pCO2 = 1 bar). Moreover, it seems there is an optimum initial concentration of the ions’ solutions for the tested HTs, which depends on the final application—c-HT1 showed a better capacity at 35 °C and c-HT2 at 300 °C. From the adsorption-desorption cycles—performed at 35 and 300 °C with the best materials using a magnetic suspension microbalance at 1 bar of CO2 partial pressure —, a working cyclic capacity of 2.69 mmol∙g−1 was achieved by the Zeolite at 35 °C; in turn, c-HT2 showed a working cyclic capacity of 0.79 mmol∙g−1 at 300 °C.

Figueiredo, Anabela↗
DOE OSTI2025

Fiber-Coupled Multipass NIR Sensor for In Situ, Real-Time Water Vapor Outgassing Monitoring

This work presents the recent development of a fiber-coupled multipass near-infrared (NIR) gas sensor used to monitor water vapor desorption of small material coupons. The gas sensor design employs a White cell topology to maximize the optical path length over a compact, hand-size footprint. Water vapor concentrations are quantified over a large dynamic range by simultaneously applying wavelength modulation and tunable diode laser absorption spectroscopy techniques. A custom headspace optimized for material desorption experiments is assembled using commercially available vacuum chamber components. We provide in situ measurements of water vapor desorption from two geometries of the industrially important silicone elastomer Sylgard-184 as a case study for sensor viability. To corroborate the results, the gas sensor data are compared to numerical simulations based on a triple-mode diffusion–sorption model, consisting of Henry, Langmuir, and Pooling modes.

gas sensor↗
DOE OSTI2020

Method and system for treatment of a gas stream that contains carbon dioxide

A method for separating carbon dioxide (CO2) from a gas stream is disclosed, in which the gas stream is reacted with a lean aminosilicone solvent in an absorber, resulting in a rich aminosilicone solvent that is then treated in a desorber to release the CO2 and regenerate lean aminosilicone solvent in a desorption reaction. The regenerated solvent is directed into a steam-producing, indirect heat exchanger that is configured to supply steam to the desorber at a temperature high enough to augment the desorption reaction. Also, selected amounts of make-up water are added to the rich aminosilicone solvent at one or more process locations between the absorber and the desorber, to lower the viscosity of the solvent and to lower the temperature required for the desorption reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Atomic Layer Deposition for Materials-Based H2 Storage: Opportunities and Limitations

The transportation demands in our growing hydrogen (H2) economy requires robust storage systems. The current commercially implemented technology in fuel cell cars relies on the well-established technology of hydrogen gas compressed to 350-700 bar, depending on the application. The compressed gas tanks in use today are bulky and cost intensive. To address this challenge, material-based storage is one of the long-term alternatives considered and constitutes the focus of this talk. Material-based storage is broadly defined as hydrogen bound to solid materials, with its binding strength varying from physisorption to porous materials, such as zeolites and metal organic frameworks, to chemisorption in (complex) metal hydrides. The ultimate targets set by the U.S. Department of Energy for this technology include a system gravimetric capacity of 6.5 wt% and volumetric capacity of 40 g/L at 100 bar, operating temperatures ranging between -40 C and +40 C and adsorption/desorption timescales of < 5 min. Storage in the form of physisorbed or chemisorbed hydrogen has guided the materials research, which metal- organic framework and (complex) metal hydrides being the most promising materials classes. A variety of these materials have met one or more of the targets, but it has remained elusive for a single material system to meet all these stringent requirements. Nano-encapsulation and low-concentration chemical additives have previously been employed separately to overcome such challenges. Functionalization via atomic layer deposition (ALD), however, offers unique characteristics that make it suitable for both, nano-encapsulation and "doping" with low-concentration additives. This deposition technique has sub-monolayer thickness control, is highly conformal in high-surface area materials and is self-limiting, i.e., once the gas-phase precursor reacts with the available surface sites, the surface reactions stop. In this presentation, we will showcase examples where ALD, more generally vapor-phase functionalization, on (complex) metal hydrides and organic frameworks has improved the material properties for H2 storage. In our first study, Al2O3 was deposited on magnesium borohydride, Mg(BH4)2, at room temperature using trimethylaluminum (TMA) and water. From our findings, encouraging initial results were obtained: the H2 desorption temperature was lowered by 60-120 degrees C, the desorbed gravimetric H2 capacity at temperatures < 250 degrees C was doubled, and the desorption kinetics increased by a factor of ~6 compared to uncoated Mg(BH4)2. However, hydrolysis reactions caused by residual surface -OH groups from the ALD water-pulse degraded the sample substantially. Through this study, the use of TMA was observed to be highly reactive with the Mg(BH4)2 surface species, leading to the strategy of exposing the sample only to TMA. The relative mole fraction of the vapor-phase additive can be precisely controlled with the number of TMA pulses and pulse duration. By tuning these parameters, we show in our second study that 10 pulses of TMA at ambient conditions were able to decrease the H2 desorption temperature by ~100 degrees C while retaining <95 % of its H2 capacity. We applied this approach with other additives such as BBr3, TiCl4 and tetrahydrofuran, and demonstrate that this unique approach opens the door to a new class of molecular additives and catalysts which cannot easily be introduced with conventional mechano-chemical or solvent-based techniques for (complex) metal-hydrides. In the case of metal organic frameworks, ALD is a promising technique to functionalize the pores with metal atoms or functional groups able to tune the gas selectivity and binding energy, for which ~15 kJ/mol has been established as the optimal value for H2 storage in sorbent materials. Vapor-phase techniques such as ALD have numerous benefits over other functionalization tools for H2 storage materials opening innumerable opportunities to the field. To exploit these opportunities, the current limitations on room temperature and water-less ALD processes needs to be overcome which will greatly expand the possibilities of encapsulation and incorporation of additives for organic frameworks and (complex) metal hydrides.

atomic layer deposition↗
DOE OSTI2022

Electrochemical pumping: An alternative solution for hydrogen embrittlement

Hydrogen embrittlement is a form of chemo-mechanical damage that is special in that it can be partially reversible. Here, in this paper, we propose a method for recovering structural alloys from hydrogen embrittlement at room temperature by electrochemically biased desorption of hydrogen. We demonstrate that the method can enable the reversion of hydrogen-induced degradation of mechanical properties, by comparing the mechanical behavior of commercial stainless steel specimens at different hydrogen charging and desorption states. These case studies also reveal the influence of electrochemical potential, H content and the characteristics of H trapping sites, on the effectiveness of this recovery approach. The limitations arising from the presence of unhealable forms of hydrogen damage, and the generic applicability of this electrochemically-assisted recovery method are also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ettringite hysteresis under sorption from molecular simulations

Highlights: • Hybrid Grand Canonical Monte Carlo (GCMC) and Molecular Dynamics (MD) simulations are performed. • Anisotropic large strain coefficient of crystal shrinkage of ettringite is provided. • Entropy increases when ettringite converts into metaettringite. • Sorption-induced stress may lead to columns collapse upon drying. • H-bonds involving OH groups in columns play a role in hysteresis. The response of ettringite under sorption is critical for the utilization of this mineral as an energy storage material and to understand the concrete durability problems associated with ettringite formation. We report molecular simulations directly sampling the osmotic ensemble to understand the sorption processes and structural changes in ettringite-metaettringite transition. Desorption branch and sorption-induced volume changes from simulations agree with the experiments. The structural changes at low relative humidity are analyzed, revealing for the first time details of metaettringite structure. The reversibility under sorption observed experimentally is captured by simulation in the ettringite domain. The reversibility in the conversion of metaettringite into ettringite is not captured by the direct simulations in the osmotic ensemble due to the large volume changes associated with ettringite desorption. Finally, we discuss the role of hydrogen bonds on the hysteresis in ettringite.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Experimental Assessment of Mammalian Lipidome Complexity Using Multimodal 21 T FTICR Mass Spectrometry Imaging

Herein, we assess the complementarity and complexity of data that can be detected within mammalian lipidome mass spectrometry imaging (MSI) via matrix-assisted laser desorption ionization (MALDI) and nanospray desorption electrospray ionization (nano-DESI). We do so by employing 21 T Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) with absorption mode FT processing in both cases, allowing unmatched mass resolving power per unit time (≥613k at m/z 760, 1.536 s transients). While our results demonstrated that molecular coverage and dynamic range capabilities were greater in MALDI analysis, nano-DESI provided superior mass error, and all annotations for both modes had sub-ppm error. Taken together, these experiments highlight the coverage of 1676 lipids and serve as a functional guide for expected lipidome complexity within nano-DESI-MSI and MALDI-MSI. To further assess the lipidome complexity, mass splits (i.e., the difference in mass between neighboring peaks) within single pixels were collated across all pixels from each respective MSI experiment. The spatial localization of these mass splits was powerful in informing whether the observed mass splits were biological or artificial (e.g., matrix related). Mass splits down to 2.4 mDa were observed (i.e., sodium adduct ambiguity) in each experiment, and both modalities highlighted comparable degrees of lipidome complexity. Further, we highlight the persistence of certain mass splits (e.g., 8.9 mDa; double bond ambiguity) independent of ionization biases. Here, we also evaluate the need for ultrahigh mass resolving power for mass splits ≤4.6 mDa (potassium adduct ambiguity) at m/z > 1000, which may only be resolved by advanced FTICR-MS instrumentation.

21T-FTICR-MS↗
DOE OSTI2020

An Electrochemically Mediated Amine Regeneration Process with a Mixed Absorbent for Postcombustion CO 2 Capture

Electrochemically mediated amine regeneration (EMAR) was recently developed to avoid the use of thermal means to release CO2 captured from postcombustion flue gas in the benchmark amine process. To address concerns related to the high vapor pressure of ethylenediamine (EDA) as the primary amine used in EMAR, a mixture of EDA and aminoethylethanolamine (AEEA) was investigated. The properties of the mixed amine systems, including the absorption rates, electrolyte pH and conductivity, and CO2 capacity, were evaluated in comparison with those of solely EDA. The mixed amine system had similar properties to that of EDA, indicating no significant changes would be necessary for the future implementation of the EMAR process with mixed amines as opposed to that with just EDA. The electrochemical performance of the mixed amines in terms of the cell voltage, gas desorption rate, electron utilization, and energetics was also investigated. A 50/50 mixture of EDA and AEEA displayed the lowest energetics: ~10% lower than that of 100% EDA. With this mixture, a continuous EMAR process, in which the absorption column was connected to the electrochemical cell as the desorption stage, was tested over 100 h. The cell voltage was very stable and there was a steady gas output close to theoretical values. The desorbed gas was further analyzed and found to be 100% CO2, confirming no evaporation of the amine. The mixed absorbent composition was also characterized using titration and nuclear magnetic resonance (NMR) spectroscopy, and the results showed no amine degradation. Furthermore, these findings that demonstrate a stable, low vapor pressure absorbent with improved energetics are promising and could be a guideline for the future development of EMAR for CO2 capture from flue gas and other sources.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Comparison of Designs of Hydrogen Isotope Separation Columns by Numerical Modeling

Mixtures of gas-phase hydrogen isotopologues (diatomic combinations of protium, deuterium, and tritium) can be separated using columns containing a solid such as palladium that reversibly absorbs hydrogen. A temperature-swing process can transport hydrogen into or out of a column by inducing temperature-dependent absorption or desorption reactions. Here, we consider two designs: a thermal cycling absorption process, which moves hydrogen back and forth between two columns, and a simulated moving bed (SMB), where columns are in a circular arrangement. We present a numerical mass and heat transport model of absorption columns for hydrogen isotope separation. It includes a detailed treatment of the absorption–desorption reaction for palladium. By comparing the isotope concentrations within the columns as a function of position and time, we observe that SMB can lead to sharper separations for a given number of thermal cycles by avoiding the remixing of isotopes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Thermal Activation of a Copper-Loaded Covalent Organic Framework for Near-Ambient Temperature Hydrogen Storage and Delivery

Copper(II) formate is efficiently incorporated into the pores of a 2D imine-based covalent organic framework (COF) via coordination with the phenol and imine groups. The coordinated metal ion is then reduced to Cu(I) with a thermal treatment that evolves CO 2 . After loading with hydrogen gas, the majority of H 2 desorbs from the coordinatively saturated Cu(II) COF at temperatures < -100 degrees C. However, the activated Cu(I) COF retains adsorbed H 2 above room temperature. Adsorption/desorption of H 2 was highly reversible. Diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) strongly supports a molecular hydrogen interaction with Cu(I). A Kissinger analysis of variable ramp rate desorption experiments estimates the enthalpy of H 2 desorption from Cu(I) at 15 kJ mol -1 . The results represent an advance toward practical H 2 storage and delivery in a lightweight, stable, and highly versatile material.

08 HYDROGEN↗
DOE OSTI2022

Highly Active and Selective Sites for Propane Dehydrogenation in Zeolite Ga-BEA

A highly selective Ga-modified zeolite BEA for propane dehydrogenation has been synthesized by grafting Ga on Zn-BEA followed by removal of Zn in the presence of H 2 . A propene selectivity of 82% at 19% propane conversion illustrates the high selectivity at 813 K. The kinetic model of the catalyzed dehydrogenation including the elementary steps of propane adsorption, first and second C–H bond cleavage, and propene and H 2 desorption demonstrates that the propane dehydrogenation rate is determined by the first C–H bond cleavage at low pC 3 H 8 , while at high pC 3 H 8 , the rate is limited by the desorption of H 2 . The active sites have been identified as dehydrated and tetrahedrally coordinated Ga 3+ in the *BEA lattice. Furthermore, the low selectivity toward aromatics is concluded to be associated with the high Lewis acid strength of lattice Ga 3+ and the low Brønsted acid strength of the hydrated Ga sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Photo-Swing CO2 Capture Using a Branched Polyethylenimine As Sorbents and TiN Light Absorber

Using branched polyethylenimine as the sorbent material for dilute CO2 capture, a photo-swing method is demonstrated in an industrially relevant support architecture using titanium nitride (TiN) nanosized light absorbers coupled with low-power LEDs with irradiances up to 420 mW cm-2. The photo-swing desorption process is applied to dry and humid streams of 400 ppm CO2 diluted in N2. Consistent with known sorption mechanisms for aminopolymers, humid CO2 streams increased the CO2 uptake, in our case by ~30%. The photo-swing CO2 capture desorbed ~83% and ~100% CO2 compared to thermally-driven desorption over the same period for a dry and humid CO2 stream, respectively. The photo-swing CO2 capture exhibits robust performance over >90 cycles without significant signs of photo(thermal) induced sorbent degradation. This work lays the groundwork for photo-swing DAC technology as a scalable, energy-efficient solution for CO2 capture, well-suited for modular systems in remote locations utilizing intermittent renewable energy sources.

36 MATERIALS SCIENCE↗