Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dynamics (Mechanics)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Collective Summary of sCO2 Materials Development (Supercritical Transformational Electric Power Generation (STEP) Level 2 Milestone Report) (Parts I - II)

Polymers such as PTFE (polytetrafluorethylene or Teflon), EPDM (ethylene propylene diene monomer) rubber, FKM fluoroelastomer (Viton), Nylon 11, Nitrile butadiene (NBR) rubber, hydrogenated nitrile rubber (HNBR) and perfluoroelastomers (FF_202) are commonly employed in super critical CO 2 (sCO2) energy conversion systems. O-rings and gaskets made from these polymers face stringent performance conditions such as elevated temperatures, high pressures, pollutants, and corrosive humid environments. In FY 2019, we conducted experiments at high temperatures (100°C and 120°C) under isobaric conditions (20 MPa). Findings showed that elevated temperatures accelerated degradation of polymers in sCO2, and that certain polymer microstructures are more susceptible to degradation over others. In FY 2020, the focus was to understand the effect of sCO2 on polymers at low (10 MPa) and high pressures (40 MPa) under isothermal conditions (100°C). It was clear that the same selectivity was observed in these experiments wherein certain polymeric functionalities showed more propensity to failure over others. Fast diffusion, supported by higher pressures and long exposure times (1000 hours) at the test temperature, caused increased damage in sCO2 environments to even the most robust polymers. We also looked at polymers under compression in sCO2 at 100°C and 20 MPa pressure to imitate actual sealing performance required of these materials in sCO2 systems. Compression worsened the physical damage that resulted from chemical attack of the polymers under these test conditions. In FY 2021, the effect of cycling temperature (from 50°C to 150°C to 50°C) for polymers under a steady sCO2 pressure of 20 MPa was studied. The aim was to understand the influence of cycling temperatures of sCO2 for typical polymers under isobaric (20 MPa) conditions. Thermoplastic polymers (Nylon, and PTFE) and elastomers (EPDM, Viton, Buna N, Neoprene, FF202, and HNBR) were subjected to 20 MPa sCO2 pressure for 50 cycles and 100 cycles in separate experiments. Samples were extracted for ex-situ characterization at 50 cycles and upon the completion of 100 cycles. Each cycle constituted of 175 minutes of cycling from 50°C to 150°C. The polymer samples were examined for physical and chemical changes by Dynamic Mechanical and Thermal Analysis (DMTA), Fourier Transform Infrared (FTIR) spectroscopy, and compression set. Density and mass changes immediately after removal from test were measured for degree of swell comparisons. Optical microscopy techniques and micro computer tomography (micro CT) images were collected on select specimens. Evaluations conducted showed that exposures to super-critical CO2 environments resulted in combinations of physical and/or chemical changes. For each polymer, the dominance of cycling temperatures under sCO2 pressures, were evaluated. Attempts were made to qualitatively link the permanent sCO2 effects to polymer micro- structure, free volume, backbone substitutions, presence of polar groups, and degree of crystallinity differences. This study has established that soft polymeric materials are conducive to failure in sCO2 through mechanisms of failure that are dependent on polymer microstructure and chemistry. Polar pendant groups, large atom substitutions on the backbone are some of the factors that are influential structural factors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quasi-static to Dynamic Response and Microstructure Development of Tantalum-Tungsten Alloys

Lawrence Livermore National Laboratory (LLNL) has a need to understand the quasi-static to dynamic mechanical response and microstructure evolution of tantalum-tungsten (Ta-W) alloys made by conventional wrought processing and additive manufacturing (AM). This two-year work scope will be performed at the Colorado School of Mines (Mines) and will include quasi-static (e.g., 10 -3 s -1 ) mechanical testing in tension and compression, along with high strain rate (Kolsky) pressure bar testing in tension and compression (e.g., 10 3 s -1 ), without and with temperature variations. Gas gun experiments at higher strain rates (e.g., over 10 3 s -1 ) will also be pursued. Complementary microstructure characterization will be performed on undeformed and deformed samples to fundamentally understand the role of processing on the microstructure characteristics and resulting deformation mechanisms that dictate the mechanical response of these alloys with variations in strain rate, temperature, and strain state. Alloys of interest will be Ta-based, containing up to 10 wt.% W. LLNL will supply initial wrought-processed material for sample machining. LLNL will also supply samples built by AM during the project for testing. Arc melting and casting may also be performed at Mines to produce small quantities of different alloys for machining and exploratory testing on an as-needed basis. This project will support multiple postdocs and graduate students at Mines, training them with the knowledge, skills, and abilities needed to study materials under extreme conditions of interest to the National Nuclear Security Agency.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Modeling Value Flows in Utility Rate Structures

As the increased adoption of distributed energy resources continues to challenge flat utility rate structures, time-varying rates and more dynamic mechanisms like transactive energy systems can better leverage customer-sited distributed energy resources to provide grid services. However, adopting new utility policies can be a timely process and requires a high level of transparency into the energy system. A wide range of stakeholders must understand who may be affected by policy changes and how. This work employs the valuation methodology developed under Pacific Northwest National Laboratory’s Transactive Systems Program to outline the functional differences in value flow under a series of conventional rate structures and a transactive energy system. The resulting value model illustrates the nuances that arise and highlights future avenues of work that will be necessary as utilities across the country continue to develop new rate structures and market mechanisms.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

H2 Materials Compatibility of Low Cost, High Pressure, Polymer H2 Dispensing Hoses

NanoSonic was recently awarded a DOE Phase IIB SBIR program for the commercialization of an innovative metal-free polymer based H2 dispensing hose to make H2 an economically viable fuel alternative to gasoline. During the Phase I and Phase II base programs, NanoSonic's H2 hose demonstrated ultra-high hydrostatic burst strength values > 31,000 psi where failure occurred due to fitting slippage, rather than hose burst. Additionally, our hoses survived > 51,000 pressure impulse cycles at 12,000 psi over a thermal cycle of -40 °C to 85 °C. These hoses also failed due to fitting slippage. Thus, our Phase IIB program is centralized on the addition of a new fitting, polymer hose refinement, and validation of a complete hose and fitting system certified for use with H2. While NanoSonic has partnered with the National Renewable Energy Laboratory (NREL) to test our hose on their robotic H2 dispensing system, we are also seeking durability with the H2 environment at the molecular level. Here, NanoSonic proposes a CRADA with Pacific Northwest National Laboratory (PNNL), who has expertise in H2 polymer materials compatibility. Together, we will determine the lifetime of our H2 hose polymer and composite constituents via: 1) time-temperature superposition (TTS) studies via dynamic mechanical analysis (DMA) under H2, 2) friction and wear resistance under in situ H2 tribometry, and 3) multi-axis strain testing under cryogenic conditions. PNNL has the unique test equipment essential to gain this type of insight and lifetime prediction data. Importantly, the work conducted under the proposed CRADA will increase the safety and reliability of our H2 hoses while expanding the market for use of our low H2 permeation polymers and durable cryogenic composites to realize the H2@Scale objectives to reduce the cost of H2.

08 HYDROGEN↗
DOE OSTI2024

Proton electromagnetic generalized polarizabilities

Electromagnetic polarizabilities are fundamental properties of the proton that characterize its response to an external electromagnetic (EM) field. The generalization of the EM polarizabilities to non-zero four-momentum transfer opens up a powerful path to study the internal structure of the proton. They map out the spatial distribution of the polarization densities in the proton, provide access to key dynamical mechanisms that contribute to the electric and magnetic polarizability effects, and allow for the determination of fundamental characteristics of the system, such as the electric and magnetic polarizability radii. This article reviews our knowledge about proton EM generalized polarizabilities (GPs). An introduction is given to the basic concepts and the theoretical framework, which is then followed by a discussion that emphasizes the recent developments and findings of the virtual Compton scattering (VCS) experiments and future perspectives on the topic.

hadrons↗
DOE OSTI2025

Hygrothermal Aging and Thermomechanical Characterization of As-Manufactured Tidal Turbine Blade Composites

This study investigates the hygrothermal aging behavior and thermomechanical properties of as-manufactured glass fiber-reinforced epoxy and thermoplastic composite tidal turbine blades. The blades were previously deployed in a marine environment and subsequently analyzed through a comprehensive suite of material characterization techniques, including hygrothermal aging, dynamic mechanical analysis (DMA), tensile testing and X-ray computed tomography (XCT). Hygrothermal aging experiments revealed that while thermoplastic composites exhibited lower overall water absorption (0.78% vs. 0.47%), they had significantly higher diffusion coefficients than epoxy (2.1 vs. 12.1 × 10 −13 m 2 s −1 ), suggesting faster saturation in operational environments. DMA results demonstrated that water ingress caused plasticization in epoxy matrices, reducing the glass transition temperature and increasing damping (112 °C to 104 °C), while thermoplastic composites showed more stable thermal behavior (87 °C glass transition temperature). Tensile testing revealed substantial reductions in ultimate strength (>40%) for both materials after prolonged water exposure, with minimal change in elastic modulus, highlighting the role of matrix degradation over fiber reinforcement. XCT image analysis showed that both composites were manufactured with high quality: no large voids or cracks were present, and the degree of misalignment was low. These findings inform future marine renewable energy composite designs by emphasizing the critical influence of moisture on long-term structural integrity and the need for optimized material systems in harsh marine environments. This work provides a rare real-world comparison of epoxy and recyclable thermoplastic tidal turbine blades, showing how laboratory aging tests and advanced imaging reveal the influence of material and manufacturing choices on long-term marine durability.

16 TIDAL AND WAVE POWER↗
DOE OSTI2020

Fractionation of Lignin for Selective Shape Memory Effects at Elevated Temperatures

We report a facile approach to control the shape memory effects and thermomechanical characteristics of a lignin-based multiphase polymer. Solvent fractionation of a syringylpropane-rich technical organosolv lignin resulted in selective lignin structures having excellent thermal stability coupled with high stiffness and melt-flow resistance. The fractionated lignins were reacted with rubber in melt-phase to form partially networked elastomer enabling selective programmability of the material shape either at 70 °C, a temperature that is high enough for rubbery matrix materials, or at an extremely high temperature, 150 °C. Utilizing appropriate functionalities in fractionated lignins, tunable shape fixity with high strain and stress recovery, particularly high-stress tolerance were maintained. Detailed studies of lignin structures and chemistries were correlated to molecular rigidity, morphology, and stress relaxation, as well as shape memory effects of the materials. The fractionation of lignin enabled enrichment of specific lignin properties for efficient shape memory effects that broaden the materials’ application window. Electron microscopy, melt-rheology, dynamic mechanical analysis and ultra-small angle neutron scattering were conducted to establish morphology of acrylonitrile butadiene rubber (NBR)-lignin elastomers from solvent fractionated lignins.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Performance of Vehicle Fuel System Elastomers and Plastics with Test Fuels Representing Gasoline Blended with 10% Ethanol (E10) and 16% Isobutanol (iBu16)

The compatibilities of fuel system elastomers and plastics were evaluated for test fuels containing 16 vol.% isobutanol (iBu16) and 10 vol.% ethanol (E10). Elastomers included two fluorocarbons, four acrylonitrile butadiene rubbers (NBRs), and one type of fluorosilicone, neoprene, and epichlorohydrin/ethylene oxide. Plastic materials included four nylon grades, three polyamides, polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), ethylene tetrafluoroethylene (ETFE), polyphenylene sulfide (PPS), high-density polyethylene (HDPE), polybutylene terephthalate (PBT), polyoxymethylene (POM), flexible polyvinylchloride (PVC), polyetherimide (PEI), polyetheretherketone (PEEK), and a phenol formaldehyde reinforced with glass fiber (GFPF). For each polymer material, the volume, mass, and hardness were measured before and after drying. Dynamic mechanical analysis (DMA) measurements were also performed on the dried specimens.For the elastomer materials the measured properties were similar for both fuels. The fluorocarbons and fluorosilicone swelled the least (~20%), while more moderate (20-45%) expansion occurred for the two NBR hose grades and (ECO). HNBR, neoprene, and silicone exhibited high swelling and softening, which likely precludes their use in many fuel systems. For the plastic materials, the observed swell was low; Nylon 11 swelled around 15%, but otherwise, their measured swell was <10%. Many of the plastics also showed sensitivity to alcohol type, as the E10 test fuel often imparted appreciably higher swell than iBu16. In general, the plastic materials showed good compatibility with the iBu16 and E10 test fuels. Here, the sole exception was the PVC material, which was structurally degraded from exposure to either fuel type. Compositional analysis showed high fuel retention in Nylon 12 and PVC. PVC also experienced a significant reduction in plasticizer compounds following exposure, which resulted in embrittlement and an increase in the glass-to-rubber transition temperature.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

pyvisco [SWR-22-30]

pyvisco is a Python library that supports the identification of Prony series parameters for linear viscoelastic materials described by a Generalized Maxwell model. The necessary material model parameters are identified by fitting a Prony series to the experimental measurement data. pyvisco allows for the identification of Prony series parameters from experimental data measured in either the frequency-domain (via Dynamic Mechanical Thermal Analysis) or time-domain (via relaxation measurements). The experimental data can be provided as raw measurement sets at different temperatures or as pre-processed master curves. An optional minimization routine is included to reduce the number of Prony elements. This routine is helpful in Finite Element simulations where reducing the computational complexity of the linear viscoelastic material models can shorten the simulation time. See also, https://pypi.org/project/pyvisco/

Springer, Martin↗
DOE OSTI2021

Simple biochemical features underlie transcriptional activation domain diversity and dynamic, fuzzy binding to Mediator

Gene activator proteins comprise distinct DNA-binding and transcriptional activation domains (ADs). Because few ADs have been described, we tested domains tiling all yeast transcription factors for activation in vivo and identified 150 ADs. By mRNA display, we showed that 73% of ADs bound the Med15 subunit of Mediator, and that binding strength was correlated with activation. AD-Mediator interaction in vitro was unaffected by a large excess of free activator protein, pointing to a dynamic mechanism of interaction. Structural modeling showed that ADs interact with Med15 without shape complementarity (‘fuzzy’ binding). ADs shared no sequence motifs, but mutagenesis revealed biochemical and structural constraints. Finally, a neural network trained on AD sequences accurately predicted ADs in human proteins and in other yeast proteins, including chromosomal proteins and chromatin remodeling complexes. These findings solve the longstanding enigma of AD structure and function and provide a rationale for their role in biology.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

Model, Design, and Control for Power Conversion in Wave Energy Converter System

Wave energy, if all been harvested along the U.S. coastline, can power around 65% of the energy consumption in U.S.. Comparing to other renewable energy sources like solar or wind, ocean wave can provide up to 90% of steady uptime. With the high energy density (2-3 kW/m 2 ), it can produce more energy with the same amount of installation area comparing to the energy density of wind turbine (0.6 kW/m 2 ) and solar panel(0.2 kW/m 2 ). The predictability of wave provides advantages like planning installation, power dispatching, and maintenance activities. Although with all these advantages, wave energy converter system is still in the research stage due to its high system cost per electricity production. One of the challenges that need to be solved is the irregularity from the wave motion that leads to high instantaneous peak power into the wave energy converter, which usually reaches up to 10 - 20 times of the average power. The high peak power will not only bring high mechanical/electrical stress but also result in an overrating design of the components in the system. Another obstacle that prevents the wave energy system from moving forward is the high testing cost from the validations in wave-energy-test sites or tank-test sites. A high-fidelity multi-disciplinary system model, including hydrodynamics, mechanical dynamics, electromagnetics, and power electronics, is needed to predict the behavior of the system and reduce the cost of design validation.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

Dynamic Monkey Bar Mechanism of Superionic Li–ion Transport in LiTaCl 6

Here, the LiTaCl 6 solid electrolyte has the lowest activation energy of ionic conduction at ambient conditions (0.165 eV), with a record high ionic conductivity for a ternary compound (11 mS cm –1 ). However, the mechanism has been unclear. We train machine-learning force fields (MLFF) on ab initio molecular dynamics (AIMD) data on-the-fly and perform MLFF MD simulations of AIMD quality up to the nanosecond scale at the experimental temperatures, which allows us to predict accurate activation energy for Li-ion diffusion (at 0.164 eV). Detailed analyses of trajectories and vibrational density of states show that the large-amplitude vibrations of Cl – ions in TaCl 6 – enable the fast Li-ion transport by allowing dynamic breaking and reforming of Li–Cl bonds across the space in between the TaCl 6 – octahedra. We term this process the dynamic-monkey-bar mechanism of superionic Li + transport which could aid the development of new solid electrolytes for all-solid-state lithium batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Dynamic Monkey Bar Mechanism of Superionic Li‐ion Transport in LiTaCl 6

Abstract The LiTaCl 6 solid electrolyte has the lowest activation energy of ionic conduction at ambient conditions (0.165 eV), with a record high ionic conductivity for a ternary compound (11 mS cm −1 ). However, the mechanism has been unclear. We train machine‐learning force fields (MLFF) on ab initio molecular dynamics (AIMD) data on‐the‐fly and perform MLFF MD simulations of AIMD quality up to the nanosecond scale at the experimental temperatures, which allows us to predict accurate activation energy for Li‐ion diffusion (at 0.164 eV). Detailed analyses of trajectories and vibrational density of states show that the large‐amplitude vibrations of Cl − ions in TaCl 6 − enable the fast Li‐ion transport by allowing dynamic breaking and reforming of Li−Cl bonds across the space in between the TaCl 6 − octahedra. We term this process the dynamic‐monkey‐bar mechanism of superionic Li + transport which could aid the development of new solid electrolytes for all‐solid‐state lithium batteries.

Lei, Ming↗
DOE OSTI2025

Combining Reactive Quantum-Mechanical Molecular-Dynamics Simulations with Mutagenesis, Crystallography, and Enzyme Kinetics to Reveal Plausible Steps of Isocyanide Hydratase Catalysis

A complete understanding of enzyme mechanisms requires atomistic details of chemical reactions. Quantum-based molecular dynamics simulations (QMD) are a potential source of this information, but trade-offs between accuracy and computational cost have limited their use. We previously developed extended Lagrangian Born–Oppenheimer molecular dynamics (XL-BOMD) methods that leverage a negligible compromise in accuracy to substantially decrease the cost of QMD simulations. Here, we develop a reactive QMD approach using the latest XL-BOMD formulation, which enables efficient simulations of highly reactive systems, and use it to investigate mechanisms of intermediate formation in isocyanide hydratase (ICH) catalysis. In QMD simulations, molecular analogs of ICH active site residues reacted with para-nitrophenyl isocyanide, forming a thioimidate. Analysis of simulated atomic configurational and charge dynamics revealed a pathway where protonation of the isocyanide carbon occurs prior to thioimidate formation and suggested a possible role of Asp17 as a proton donor in the early phase of ICH catalysis. To test whether the pathway seen using the reactive QMD approach might be relevant to ICH catalysis, we performed X-ray crystallography and pre-steady-state enzyme kinetics studies of wild-type and D17N mutant ICH. Both the structure and kinetics are sensitive to the D17N mutation in a manner that is consistent with the order of the reaction steps seen in the simulations. Mobile protons play essential roles in many enzymes, yet they are difficult to observe experimentally, making the ordering of proton-dependent steps ambiguous in many enzyme mechanisms. The ability to directly simulate model reactions for the design of experiments that provide information about enzyme mechanisms involving mobile protons demonstrates the significance of our reactive QMD approach and motivates further biological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Perspectives on the Dynamic Nuclear Polarization Mechanisms of Monoradicals: Overhauser Effect or Thermal Mixing?

This mini-review summarizes the evolving debate regarding the origins of the absorptive features seen in the dynamic nuclear polarization (DNP) spectra of certain monoradicals when they are irradiated at their electron Larmor frequency. This feature has drawn attention due to its reverse scaling with respect to the magnetic field strength and potential for high-field DNP. Two competing hypotheses have been introduced to explain the DNP feature based on (1) the Overhauser effect and low-temperature molecular dynamics and (2) radical clustering and a thermal mixing mechanism. Since the original discovery, a large number of experimental observations have been made in attempts to understand and ultimately leverage the mechanism. We summarize these observations and provide critical assessments of how the competing hypotheses approach them.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Vascular K ATP channel structural dynamics reveal regulatory mechanism by Mg-nucleotides

Vascular tone is dependent on smooth muscle K ATP channels comprising pore-forming Kir6.1 and regulatory SUR2B subunits, in which mutations cause Cantú syndrome. Unique among K ATP isoforms, they lack spontaneous activity and require Mg-nucleotides for activation. Structural mechanisms underlying these properties are unknown. Here, we determined cryogenic electron microscopy structures of vascular K ATP channels bound to inhibitory ATP and glibenclamide, which differ informatively from similarly determined pancreatic K ATP channel isoform (Kir6.2/SUR1). Unlike SUR1, SUR2B subunits adopt distinct rotational “propeller” and “quatrefoil” geometries surrounding their Kir6.1 core. The glutamate/aspartate-rich linker connecting the two halves of the SUR-ABC core is observed in a quatrefoil-like conformation. Molecular dynamics simulations reveal MgADP-dependent dynamic tripartite interactions between this linker, SUR2B, and Kir6.1. The structures captured implicate a progression of intermediate states between MgADP-free inactivated, and MgADP-bound activated conformations wherein the glutamate/aspartate-rich linker participates as mobile autoinhibitory domain, suggesting a conformational pathway toward K ATP channel activation.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Unveiling the Mechanism of Mn Dissolution Through a Dynamic Cathode‐Electrolyte Interphase on LiMn2O4

Abstract Understanding the formation and evolution of the cathode‐electrolyte interphase (CEI), which forms at the interface between the cathode and electrolyte, is crucial for revealing degradation mechanisms in cathode materials, especially for developing strategies to stabilize the interphase in the strongly oxidizing conditions that evolve at high operating voltages in next‐generation Li‐ion batteries. However, The present understanding of the CEI is challenged by its complex and dynamic nature. In this work, near‐edge X‐ray absorption fine structure spectroscopy, electrochemical characterization, and reactive molecular dynamics simulations are combined to reveal a mechanism for CEI formation and evolution above model LiMn 2 O 4 (LMO) thin‐film electrodes in contact with conventional carbonate‐based electrolytes. It is found that Mn dissolution from LMO can be understood in terms of repetitive Mn 3 O 4 formation and dissolution behavior during cycling, which is closely connected to electrolyte decomposition and a key aspect of the CEI formation and growth. The behavior of the CEI in this model system offers detailed insight into the dynamic chemistry of the interphase, underscoring the important role of electrolyte composition and cathode surface structure in interphase degradation.

Ou, Wenhan↗