SEARCH · Search NASA

Results for “Electromagnetic Induction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1993

An AC-electromagnetic bearing for flywheel energy storage in space

A repulsive type AC-electromagnetic bearing was developed and tested. It was conceived on the basis of the so-called Magnetic River suspension for high-speed trains. The appearance of the bearing is similar to the traditional DC-type electromagnetic bearing but the operating principle is different. The magnets are fed with alternating current instead of direct current and the rotor is fitted with a conducting sleeve (e.g. aluminum) instead of a ferromagnetic sleeve. The repulsion is due to induction of eddy-currents in the conducting sleeve. The bearing is inherently stable and requires no feedback control. It provides support in five degrees of freedom such that a short rotor may be fully supported by a single bearing. These capabilities were demonstrated experimentally. On the down side, the load carrying capacity and the damping obtained so far were quite low compared to the DC-type bearing. Also, significant heating of the conducting sleeve was experienced. The AC-bearing is essentially a modified induction motor and there are strong indications that it can be run both as a motor and as a generator with no commutator requirements. It is therefore considered to be a good candidate for support of energy storage flywheels in space.

Nikolajsen, Jorgen L.↗

NASA NTRS2001

High Power Thruster Based on Inductive Magnetized Plasmoid Acceleration

Regardless of the power source, deep space missions will require both high specific impulse (greater than 500 s) and high thrust power (greater than 100kW). These high Isp thrusters will need to have high electrical efficiency (approx. 90%) and low specific mass (alpha approximately less than 10 kg/kW) as well. Additionally they should have high thrust to allow greater mission flexibility. All these requirements can potentially be achieved with the pulsed formation and acceleration of magnetically self-confined plasmoids commonly referred to as compact toroids (CTs). An electromagnetic plasma thruster based on CT acceleration makes an ideal candidate for a high power, high Isp thruster, since the CT is magnetically isolated from the accelerator so that there is no contact between the propellant and the accelerator. The transfer of momentum to the CT occurs through an electromagnetic interaction with the magnetic field. By maintaining an axial magnetic field gradient across it, the directed velocity of the CT can be increased indefinitely. In previous experiments carried out at the University of Washington, CT's of near milligram mass were accelerated to velocities of 250 km/s in a single pulse. The ejection of the plasmoid by an external axial field also avoids the serious problem of detachment, which would occur in thrusters that employ a magnetic mirror or magnetic nozzle. To employ the CT for propulsion, one must design, construct and test a plasma source that is capable of generating a self-confined plasma inductively, and to do it repeatedly at a sufficiently high rep rate. A repetitively pulsed 100 kW level FRC thruster was built and was operated for short bursts at a 10 kHz rep rate and will be described. Another regime for the FRC thruster however is to produce an FRC in a more conventional manner at high voltage and magnetic field. With the large energy transfer with each pulse, the rep rate for this approach is much lower (approximately 100 Hz). This is the approach that is being evaluated at MSFC in the FAST experiment. The purpose of this experiment is to build an FRC thruster, measure its performance characteristics e.g. specific impulse, thrust, and efficiency. This experiment will also be described as well as various mission scenarios that that are well matched for this type of propulsion.

Slough, John↗

NASA NTRS1962

The Analysis of a Vortex Type Magnetohydrodynamic Induction Generator

Consideration it is given to the performance to the characteristics of an AC magnetohydrodynamic power generator, A rotating magnetic field is imposed on the vortex flow of an electrically conducting fluid, which is injected tangentially into an annulus formed by two nonconducting concentric cylinders and two nonconducting end plates. A perturbation technique is used to determine the two dimensional velocity and three dimensional electromagnetic field and current distributions. Finally, the generated power, the ohmic losses, the effective power and the electrical efficiency of the converter system are calculated.

MAGNETOHYDRODYNAMIC GENERATOR↗

NASA NTRS2004

Numerical Modeling and Testing of an Inductively-Driven and High-Energy Pulsed Plasma Thrusters

Pulsed Plasma Thrusters (PPTs) are advanced electric space propulsion devices that are characterized by simplicity and robustness. They suffer, however, from low thrust efficiencies. This summer, two approaches to improve the thrust efficiency of PPTs will be investigated through both numerical modeling and experimental testing. The first approach, an inductively-driven PPT, uses a double-ignition circuit to fire two PPTs in succession. This effectively changes the PPTs configuration from an LRC circuit to an LR circuit. The LR circuit is expected to provide better impedance matching and improving the efficiency of the energy transfer to the plasma. An added benefit of the LR circuit is an exponential decay of the current, whereas a traditional PPT s under damped LRC circuit experiences the characteristic "ringing" of its current. The exponential decay may provide improved lifetime and sustained electromagnetic acceleration. The second approach, a high-energy PPT, is a traditional PPT with a variable size capacitor bank. This PPT will be simulated and tested at energy levels between 100 and 450 joules in order to investigate the relationship between efficiency and energy level. Arbitrary Coordinate Hydromagnetic (MACH2) code is used. The MACH2 code, designed by the Center for Plasma Theory and Computation at the Air Force Research Laboratory, has been used to gain insight into a variety of plasma problems, including electric plasma thrusters. The goals for this summer include numerical predictions of performance for both the inductively-driven PPT and high-energy PFT, experimental validation of the numerical models, and numerical optimization of the designs. These goals will be met through numerical and experimental investigation of the PPTs current waveforms, mass loss (or ablation), and impulse bit characteristics.

Parma, Brian↗

NASA NTRS2014

Negative Dielectric Constant Material Based on Ion Conducting Materials

Metamaterials or artificial negative index materials (NIMs) have generated great attention due to their unique and exotic electromagnetic properties. One exemplary negative dielectric constant material, which is an essential key for creating the NIMs, was developed by doping ions into a polymer, a protonated poly(benzimidazole) (PBI). The doped PBI showed a negative dielectric constant at megahertz (MHz) frequencies due to its reduced plasma frequency and an induction effect. The magnitude of the negative dielectric constant and the resonance frequency were tunable by doping concentration. The highly doped PBI showed larger absolute magnitude of negative dielectric constant at just above its resonance frequency than the less doped PBI.

Gordon, Keith L.↗

NASA NTRS2017

Negative Dielectric Constant Material Based on Ion Conducting Materials

Metamaterials or artificial negative index materials (NIMs) have generated great attention due to their unique and exotic electromagnetic properties. One exemplary negative dielectric constant material, which is an essential key for creating the NIMs, was developed by doping ions into a polymer, a protonated poly (benzimidazole) (PBI). The doped PBI showed a negative dielectric constant at megahertz (MHz) frequencies due to its reduced plasma frequency and an induction effect. The magnitude of the negative dielectric constant and the resonance frequency were tunable by doping concentration. The highly doped PBI showed larger absolute magnitude of negative dielectric constant at just above its resonance frequency than the less doped PBI.

Gordon, Keith L.↗

NASA NTRSDate not supplied

Combined Analysis of NASA's High Efficiency Megawatt Motor and Its Converter

NASA’s High Efficiency Megawatt Motor (HEMM) is being developed to achieve the performance needed by single aisle class electrified aircraft. It is a 1.4 MW electric machine designed as a generator for NASA’s STARC-ABL concept vehicle. It has performance objectives of greater than 16 kW/kg electromagnetic specific power and efficiency of greater than 98%. The key enabling technology for HEMM’s high performance metrics is a superconducting rotor cooled by an integrated cryocooler. HEMM’s integrated cryocooler is being designed to only lift 50 W of heat at its target 50 K cold tip operating temperature. HEMM’s superconducting rotor therefore needs to have essentially zero electromagnetic losses in order to stay below the 50 W heat rejection limit of the cryocooler. This paper presents the combined analysis of HEMM and a preliminarily designed HEMM converter to analyze the rotor loss impact of several potential converter filter topologies. The analysis results point to interleaving and series inductance filters not being sufficient to suppress switching harmonic caused rotor loss. Paths forward to develop a converter to eliminate rotor loss are discussed.

Matthew Granger↗

NASA NTRSDate not supplied

Combined Analysis of NASA's High Efficiency Megawatt Motor and Its Converter

Matthew Granger↗

NASA NTRS1991

Makeup and uses of a basic magnet laboratory for characterizing high-temperature permanent magnets

A set of instrumentation for making basic magnetic measurements was assembled in order to characterize high intrinsic coercivity, rare earth permanent magnets with respect to short term demagnetization resistance and long term aging at temperatures up to 300 C. The major specialized components of this set consist of a 13 T peak field, capacitor discharge pulse magnetizer; a 10 in. pole size, variable gap electromagnet; a temperature controlled oven equipped with iron cobalt pole piece extensions and a removable paddle that carries the magnetization and field sensing coils; associated electronic integrators; and sensor standards for field intensity H and magnetic moment M calibration. A 1 cm cubic magnet sample, carried by the paddle, fits snugly between the pole piece extensions within the electrically heated aluminum oven, where fields up to 3.2 T can be applied by the electromagnet at temperatures up to 300 C. A sample set of demagnetization data for the high energy Sm2Co17 type of magnet is given for temperatures up to 300 C. These data are reduced to the temperature dependence of the M-H knee field and of the field for a given magnetic induction swing, and they are interpreted to show the limits of safe operation.

Niedra, Janis M.↗

NASA NTRS2023

The Impact of Soft Magnetic Materials in Electrified Aircraft Applications

Electrical systems with high power and high power density are integral to many aerospace and energy applications. These systems, enabled by power electronics with wide bandgap semiconductor devices, require management of both efficiency/thermal aspects and electromagnetic interference that are problems specific to high power and high frequency applications, respectively. In addition to advanced active components, these applications also require passive components (inductors, capacitors, conductors) capable of operation under challenging conditions. This work surveys the state of the art of magnetic components and soft magnetic materials used as inductive cores. The wide variety of motor and converter topologies translates to a variety of requirements in the magnetics including mechanical properties, permeabilities, and frequency response. The scaling impact of material properties will be surveyed with respect to component performance and sizing, using both data from experiment and the published literature. Variations on simulations, both in lumped circuits and finite element models, will also be discussed as these are important aspects of the design phase of modern power electronics.

Alex Leary↗

NASA NTRS1984

Axisymmetric electromagnetic field influence on the characteristic velocity of an arc-jet

Tests for determining the influence of an axisymmetric EM field on the characteristic velocity of an arc jet are presented. The experimental set up is briefly described. Tests were performed with rotation induced by the centrifugal and magnetic fields in the same sense. The fuels used were HE and N2 and the results are discussed. It is found that by variation of the induction, current, and arc jet strength, the behavior is determined essentially by the shape of the cathodic and anodic blobs on the electrodes together with their movement under the combined effect of the aerodynamic and magnetic fields. In view of the different characteristics of He and N2 in respect to the dissociation heat and ionization, it is expected that the regime of the arc jet when used with H2 fuel will be similar to that with He.

Oggero, M.↗

NASA NTRS1971

High frequency electromagnetic response of the moon

It is shown that the contribution of higher harmonics to the lunar transfer functions for the tangential components of the surface magnetic field is significant at frequencies greater than 0.01 Hz. The inclusion of the higher harmonics shows that there are two distinct transfer functions corresponding to the components of the tangential surface magnetic field perpendicular and parallel to the direction of the wave vector of the external disturbance forcing the lunar induction. The dependences of these transfer functions on frequency and location are determined. The effects of the higher harmonics can: (1) account for a hitherto unexplained feature in the Apollo 12-Explorer 35 transfer functions, namely the rolloff at high frequencies; and (2) offer a possible explanation for the frequency dependence of the difference between the transfer functions for the two orthogonal components of the surface magnetic field. The harmonic response of a simple current layer model of the moon is derived.

Schubert, G.↗

NASA NTRS1972

High-frequency electromagnetic response of the moon.

It is shown that the contribution of higher harmonics to the lunar transfer functions for the tangential components of the surface magnetic field is significant at frequencies greater than 0.01 Hz. The inclusion of the higher harmonics shows that there are two distinct transfer functions corresponding to the components of the tangential surface magnetic field perpendicular and parallel to the direction of the wave vector of the external disturbance forcing the lunar induction. The dependences of these transfer functions on frequency and location are determined. The effects of the higher harmonics can (1) account for a hitherto unexplained feature in the Apollo 12 and Explorer 35 transfer functions, namely the rolloff at high frequencies, and (2) offer a possible explanation for the frequency dependence of the difference between the transfer functions for the two orthogonal components of the surface magnetic field.

Schubert, G.↗

NASA NTRS1990

Self-collimated electromagnetic jets from magnetized accretion disks - The even-symmetry case

This paper extends the previous treatment (Lovelace et al., 1987) of the origin of self-collimated EM jets to the case of even field symmetry, where the magnetic flux function Psi(r, z) is an even function of z. A viscous resistive accretion disk is assumed to surround a black hole with a force-free plasma outside of the disk. Inside the disk, the induction equation is solved for Psi(r, z) and the toroidal magnetic field. Outside the disk, previous results are used to study the formation of self-collimated EM jets. In contrast with the odd-symmetry case, for even symmetry the toroidal magnetic field acts to vertically compress the disk; a comparatively large toroidal magnetic field can exist inside the disk; and an appreciable fraction (possibly all) of the available accretion power can go into the jets.

Wang, J. C. L.↗

NASA NTRS1992

Finite Element Modeling of the Bulk Magnitization of Railroad Wheels to Improve Test Conditions for Magnetoacoustic Residual Stress Measurements

The magnetoacoustic measurement technique has been used successfully for residual stress measurements in laboratory samples. However, when used to field test samples with complex geometries, such as railroad wheels, the sensitivity of the method declines dramatically. It has been suggested that the decrease in performance may be due, in part, to an insufficient or nonuniform magnetic induction in the test sample. The purpose of this paper is to optimize the test conditions by using finite element modeling to predict the distribution of the induced bulk magnetization of railroad wheels. The results suggest that it is possible to obtain a sufficiently large and uniform bulk magnetization by altering the shape of the electromagnet used in the tests. Consequently, problems associated with bulk magnetization can be overcome, and should not prohibit the magnetoacoustic technique from being used to make residual stress measurements in railroad wheels. We begin by giving a brief overview of the magnetoacoustic technique as it applies to residual stress measurements of railroad wheels. We then define the finite element model used to predict the behavior of the current test configuration along with the nonlinear constitutive relations which we obtained experimentally through measurements on materials typically used to construct both railroad wheels and electromagnets. Finally, we show that by modifying the pole of the electromagnet it is possible to obtain a significantly more uniform bulk magnetization in the region of interest.

Fulton, J. P.↗

NASA NTRS2007

Maintaining Stability During a Conducted-Ripple EMC Test

An improved technique, and electronic circuitry to implement the technique, have been developed for a military-standard electromagnetic-compatibility (EMC) test in which one analyzes susceptibility to low-frequency ripple conducted into the equipment under test via a DC power line. In the traditional technique for performing the particular test, the ripple is coupled onto the DC power line via a transformer. Depending upon some design details of the equipment under test, the inductance of the transformer can contribute a degree of instability that results in an oscillation of amplitude large enough to destroy the equipment. It is usually possible to suppress the oscillation by connecting a damping resistor to the primary terminals of the ripple-injection transformer. However, it is important to emphasize the usually in the preceding sentence: sometimes, the resistive damping becomes insufficient to suppress destructive oscillation. In addition, undesirably, the resistor contributes to power dissipation and power demand, and thereby also necessitates the use of a larger ripple voltage amplifier. Yet another disadvantage of the transformer-coupling technique is that the transformer introduces low-frequency distortion of the injected ripple voltage. The improved technique makes it possible to inject ripple with very low distortion at low frequency, without inducing oscillation. In this technique, a transformer is not used: Instead, power is fed to the equipment under test via series power field-effect transistors (FETs) controlled by a summing operational amplifier. One of the inputs to the amplifier controls the DC component of the power-line voltage; the other input, generated by an external oscillator, controls the ripple component. The circuitry for implementing this technique includes panel displays, an internal power supply for the operational amplifier and panel displays, and amplitude controls for the DC and ripple powerline voltage components.

Vorperian, Vatche↗

NASA NTRS2006

EMI Filters for Low-Temperature Applications

Filters that suppress electromagnetic interference (EMI) on signal cables connected to cryogenic electronic equipment can be made from cores consisting of high-permeability materials. The basic principle of operation of these filters is the same as that of the ferrite-core common-mode EMI filters now commonly used on cables that connect computers with peripheral equipment. An inductive EMI filters blocks EMI due to its impedance to high frequency EMI signals. Since the impedance is proportional to the permeability, a material with high permeability forms the core of such a filter.

Chui, Talso↗

NASA NTRS1980

Determination of efficiencies, loss mechanisms, and performance degradation factors in chopper controlled dc vehical motors. Section 2: The time dependent finite element modeling of the electromagnetic field in electrical machines: Methods and applications

The time dependent solution of the magnetic field is introduced as a method for accounting for the variation, in time, of the machine parameters in predicting and analyzing the performance of the electrical machines. The method of time dependent finite element was used in combination with an also time dependent construction of a grid for the air gap region. The Maxwell stress tensor was used to calculate the airgap torque from the magnetic vector potential distribution. Incremental inductances were defined and calculated as functions of time, depending on eddy currents and saturation. The currents in all the machine circuits were calculated in the time domain based on these inductances, which were continuously updated. The method was applied to a chopper controlled DC series motor used for electric vehicle drive, and to a salient pole sychronous motor with damper bars. Simulation results were compared to experimentally obtained ones.

Hamilton, H. B.↗