Results for “Entry descent” — Page 10

NASA NTRS2019

Mars Reconnaissance Orbiter maneuver plan for Mars 2020 entry, descent, and landing support and beyond

The Mars Reconnaissance Orbiter (MRO) spacecraft continues to perform valuable science observations at Mars, provide telecommunication relay for surface assets, and characterize landing sites for future missions. MRO provided primary relay support for the InSight Mission during Entry, Descent, and Landing (EDL) on November26, 2018. This paper discusses the current maneuver plan to support Mars 2020 EDL and maintain MRO’s orbit for science operations through 2028.

Menon, Premkumar R.↗

NASA NTRS2007

Atmospheric Environments for Entry, Descent and Landing (EDL)

Scientific measurements of atmospheric properties have been made by a wide variety of planetary flyby missions, orbiters, and landers. Although landers can make in-situ observations of near-surface atmospheric conditions (and can collect atmospheric data during their entry phase), the vast majority of data on planetary atmospheres has been collected by remote sensing techniques from flyby and orbiter spacecraft (and to some extent by Earth-based remote sensing). Many of these remote sensing observations (made over a variety of spectral ranges), consist of vertical profiles of atmospheric temperature as a function of atmospheric pressure level. While these measurements are of great interest to atmospheric scientists and modelers of planetary atmospheres, the primary interest for engineers designing entry descent and landing (EDL) systems is information about atmospheric density as a function of geometric altitude. Fortunately, as described in in this paper, it is possible to use a combination of the gas-law relation and the hydrostatic balance relation to convert temperature-versus-pressure, scientific observations into density-versus-altitude data for use in engineering applications. The following section provides a brief introduction to atmospheric thermodynamics, as well as constituents, and winds for EDL. It also gives methodology for using atmospheric information to do "back-of-the-envelope" calculations of various EDL aeroheating parameters, including peak deceleration rate ("g-load"), peak convective heat rate. and total heat load on EDL spacecraft thermal protection systems. Brief information is also provided about atmospheric variations and perturbations for EDL guidance and control issues, and atmospheric issues for EDL parachute systems. Subsequent sections give details of the atmospheric environments for five destinations for possible EDL missions: Venus. Earth. Mars, Saturn, and Titan. Specific atmospheric information is provided for these destinations, and example results are presented for the "back-of-the-envelope" calculations mentioned above.

Justus, Carl G.↗

NASA NTRSDate not supplied

Entry, Descent, and Landing GN&C System Evaluation via Cable-Driven Emulation Robotics

An innovative cable-driven parallel robot named the Six Degree-of-Freedom Tendon Actu- ated Robot (STAR), recently developed by researchers at NASA Johnson Space Center, was built to enable entry, descent, and landing (EDL) emulation experiments. Upon functional testing and system verification, STAR employed several simulated EDL trajectories to validate velocimeter LIDAR-based sensor models for cooperative terrain relative navigation applica- tions for its first testing campaign. The STAR lab also hosted researchers from Astrobotic to evaluate the real-time performance of a newly developed sensor payload, UltraNav, through hardware in-the-loop-testing (HWIL). This work introduces the STAR system along with its accompanying testing utilities and capabilities, and deliver the experimental methodology and results of test campaigns performed with the STAR facility to date.

navigation↗

NASA NTRS2011

Overview of the NASA Entry, Descent and Landing Systems Analysis Exploration Feed-Forward Study

Technology required to land large payloads (20 to 50 mt) on Mars remains elusive. In an effort to identify the most viable investment path, NASA and others have been studying various concepts. One such study, the Entry, Descent and Landing Systems Analysis (EDLSA) Study [1] identified three potential options: the rigid aeroshell, the inflatable aeroshell and supersonic retropropulsion (SRP). In an effort to drive out additional levels of design detail, a smaller demonstrator, or exploration feed-forward (EFF), robotic mission was devised that utilized two of the three (inflatable aeroshell and SRP) high potential technologies in a configuration to demonstrate landing a two to four metric ton payload on Mars. This paper presents and overview of the maximum landed mass, inflatable aeroshell controllability and sensor suite capability assessments of the selected technologies and recommends specific technology areas for additional work.

DwyerCianciolo, Alicia M.↗

NASA NTRS2020

Mid Lift-to-Drag Ratio Rigid Vehicle 6-DoF Performance for Human Mars Entry, Descent, and Landing: A Fractional Polynomial Powered Descent Guidance Approach

Defining a feasible vehicle design and mission architecture capable of reliably delivering apayload of 20 metric tons (mt) or more is a great challenge for landing humans on Mars. TheMid Lift-to-Drag Rigid Vehicle (MRV), a rigid decelerator studied in NASA’s Entry, Descent,and Landing Architecture Study (EDLAS), has shown to be a viable vehicle candidate forfuture human Mars missions. As the vehicle concept matures, models of increasing fidelity areadded to the six-degree-of-freedom (6DoF) EDL simulation. This paper presents 6DoFsimulation results using model updates for vehicle mass properties, fineness ratio, andaerodynamic-propulsive interactions. Additionally, an assessment of the Fractional-Polynomial Powered Descent Guidance (FP2DG) performance is presented, and the vehicleperformance is compared with the Tunable Apollo Powered Descent Guidance (TAPDG).Finally, Monte Carlo results of the vehicle design trades are presented.

Johnson, Breanna J.↗

NASA NTRS2020

InSight Entry, Descent and Landing Post-Flight Performance Assessment

On November 26, 2018, the Interior Exploration using Seismic Investigations, Geodesy and Heat Transport (InSight) lander successfully touched down on the surface of Mars. NASA Langley Research Center’s (LaRC) Program to Optimize Simulated Trajectories II (POST2) was used during both project development and flight operations to assess the Entry, Descent and Landing (EDL) vehicle performance against related requirements across the expected range of possible environmental and spacecraft conditions. During flight operations, these analyses were used to evaluate the need for updating flight software EDL parameters and the effects of executing a trajectory correction maneuver (TCM). Therefore, the NASA LaRC POST2 simulation had a critical role during the cruise, approach and ultimately EDL phases of the mission. This paper presents results of the final pre- and post- EDL flight performance assessments. A summary of the reconstructed “as-flown” trajectory with a comparison of key EDL metrics to the nominal and three-sigma bound pre-EDL predictions is also provided. Emphasis on the trajectory between entry interface and parachute deploy is provided as this is the period during which deviations from the pre-EDL prediction occurred. The post-flight assessment provides important verification of the POST2 models and analysis techniques used for InSight, providing critical feed-forward information to future lander missions.

Robert W Maddock↗

NASA NTRS2013

Risk-Constrained Dynamic Programming for Optimal Mars Entry, Descent, and Landing

A chance-constrained dynamic programming algorithm was developed that is capable of making optimal sequential decisions within a user-specified risk bound. This work handles stochastic uncertainties over multiple stages in the CEMAT (Combined EDL-Mobility Analyses Tool) framework. It was demonstrated by a simulation of Mars entry, descent, and landing (EDL) using real landscape data obtained from the Mars Reconnaissance Orbiter. Although standard dynamic programming (DP) provides a general framework for optimal sequential decisionmaking under uncertainty, it typically achieves risk aversion by imposing an arbitrary penalty on failure states. Such a penalty-based approach cannot explicitly bound the probability of mission failure. A key idea behind the new approach is called risk allocation, which decomposes a joint chance constraint into a set of individual chance constraints and distributes risk over them. The joint chance constraint was reformulated into a constraint on an expectation over a sum of an indicator function, which can be incorporated into the cost function by dualizing the optimization problem. As a result, the chance-constraint optimization problem can be turned into an unconstrained optimization over a Lagrangian, which can be solved efficiently using a standard DP approach.

Ono, Masahiro↗

NASA NTRSDate not supplied

Mars InSight Entry, Descent, and Landing Trajectory and Atmosphere Reconstruction

The InSight mission landed on the surface of Mars on November 26th, 2018. The InSight system performance met all design requirements, although several performance metrics fell near the boundaries of the predictions. The peak deceleration was high, the overall timeline was short, and the landing site was uprange and crossrange from the target. This paper describes the reconstruction of the entry, descent, and landing trajectory and atmosphere. The approach utilizes a Kalman filter to blend sensor data to obtain the vehicle trajectory. The aerodynamic database is used in combination with the sensed accelerations to obtain estimates of the atmosphere-relative state, which in turn is used to derive the free-stream atmospheric conditions during entry, until the time of parachute deployment. The results indicate that the reconstructed atmosphere was approximately 1σbelow the preflight atmosphere. Analysis of the reconstructed vehicle attitude angles indicate that the aerodynamic lift was oriented downward at entry. The vehicle developed a roll rate during entry, which directed a component of the lift to the north. The low density and aerodynamic lift direction are determined to be the primary causes of the high deceleration, short timeline, and location of the landing site relative to the target.

Christopher D Karlgaard↗

NASA NTRS2020

Mars InSight Entry, Descent, and Landing Trajectory and Atmosphere Reconstruction

The InSight mission landed on the surface of Mars on November 26th, 2018. The InSight system performance met all design requirements, although several performance metrics fell near the boundaries of the predictions. The peak deceleration was high, the overall timeline was short, and the landing site was uprange and crossrange from the target. This paper describes the reconstruction of the entry, descent, and landing trajectory and atmosphere. The approach utilizes a Kalman filter to blend sensor data to obtain the vehicle trajectory. The aerodynamic database is used in combination with the sensed accelerations to obtain estimates of the atmosphere-relative state, which in turn is used to derive the free-stream atmospheric conditions during entry, until the time of parachute deployment. The results indicate that the reconstructed atmosphere was approximately 1σbelow the preflight atmosphere. Analysis of the reconstructed vehicle attitude angles indicate that the aerodynamic lift was oriented downward at entry. The vehicle developed a roll rate during entry, which directed a component of the lift to the north. The low density and aerodynamic lift direction are determined to be the primary causes of the high deceleration, short timeline, and location of the landing site relative to the target.

Christopher D Karlgaard↗

NASA NTRSDate not supplied

Parametric Cost Modeling of a Mid-Lift-to-Drag Ratio Vehicle for Human Mars Entry, Descent, and Landing

Cost is one of the biggest obstacles to sending humans to Mars. However, spacecraft costs are typically estimated after the preliminary vehicle and mission concepts have been designed. By automating the cost estimation process, the effect of any change in vehicle or mission design on the mission cost can be determined more rapidly. This paper uses the tool SAPE-C (Systems Analysis for Planetary Entry, Descent, and Landing-Cost). SAPE-C integrates the cost modeling software SEER-H (System Estimation and Evaluation of Resources-Hardware) with a number of systems analysis tools and enables large design tradespace exploration early in the design process. SAPE-C is used to analyze several tradespaces of the Mid-Lift-to-Drag ratio rigid entry vehicle for human Mars missions. Key findings include quantifying the impacts of payload, vehicle length, and main engine specific impulse on the overall cost of the vehicle, and how the payload per lander and number of landers affects the cost of a campaign to Mars.

Mid L/D↗

NASA NTRSDate not supplied

Parametric Cost Modeling of a Mid-Lift-to-Drag Ratio Vehicle for Human Mars Entry, Descent, and Landing

Cost is one of the biggest obstacles to sending humans to Mars. However, spacecraft costs are typically estimated after the preliminary vehicle and mission concepts have been designed. By automating the cost estimation process, the effect of any change in vehicle or mission design on the mission cost can be determined more rapidly. This paper uses the tool SAPE-C (Systems Analysis for Planetary Entry, Descent, and Landing-Cost). SAPE-C integrates the cost modeling software SEER-H (System Estimation and Evaluation of Resources-Hardware) with a number of systems analysis tools and enables large design tradespace exploration early in the design process. SAPE-C is used to analyze several tradespaces of the Mid-Lift-to-Drag ratio rigid entry vehicle for human Mars missions. Key findings include quantifying the impacts of payload, vehicle length, and main engine specific impulse on the overall cost of the vehicle, and how the payload per lander and number of landers affects the cost of a campaign to Mars.

Paul D Friz↗

NASA NTRSDate not supplied

Parametric Cost Modeling of a Mid-Lift-to-Drag Ratio Vehicle for Human Mars Entry, Descent, and Landing

Cost is one of the biggest obstacles to sending humans to Mars. However, spacecraft costs are typically estimated after the preliminary vehicle and mission concepts have been designed. By automating the cost estimation process, the effect of any change in vehicle or mission design on the mission cost can be determined more rapidly. This paper uses the tool SAPE-C (Systems Analysis for Planetary Entry, Descent, and Landing-Cost). SAPE-C integrates the cost modeling software SEER-H (System Estimation and Evaluation of Resources-Hardware) with a number of systems analysis tools and enables large design tradespace exploration early in the design process. SAPE-C is used to analyze several tradespaces of the Mid-Lift-to-Drag ratio rigid entry vehicle for human Mars missions. Key findings include quantifying the impacts of payload, vehicle length, and main engine specific impulse on the overall cost of the vehicle, and how the payload per lander and number of landers affects the cost of a campaign to Mars.

Paul D Friz↗

NASA NTRS2009

Cassini/Huygens Probe Entry, Descent, and Landing (EDL) at Titan Independent Technical Assessment

Starting in January 2004, the NESC has received several communications from knowledgeable technical experts at NASA expressing shared concerns (mainly at the Langley Research Center (LaRC) and Ames Research Center (ARC)) about Huygens mission success. It was suggested that NASA become more technically involved directly in the analysis of Huygens' entry, descent and landing (EDL) focusing on the parachute deployment trigger performance and the resultant effects on the operation of the parachute system, and the determination of the radiative heating environment at Titan by ESA and the corresponding thermal protection system (TPS) response. A NESC Team was formed and tasked to provide an independent assessment of these concerns. The results of that assessment are documented in this report.

Powell, Richard W.↗

NASA NTRS2020

InSight Entry, Descent and Landing Pre-Flight Performance Predictions

On November 26, 2018, the Interior Exploration using Seismic Investigations, Geodesy and Heat Transport (InSight) lander successfully touched down on the surface of Mars. Over its seven-plus year development, NASA Langley Research Center’s (LaRC) Program to Optimize Simulated Trajectories II (POST2) was used to assess the mission’s Entry, Descent and Landing (EDL) vehicle system performance against related requirements across the full range of possible environmental and spacecraft conditions. Much of the simulation code was derived from the Phoenix mission, for which this vehicle is very similar. The InSight six degree-of-freedom simulation included models for Mars atmosphere, gravity and digital elevation maps of the landing location. Additionally, vehicle specific aerodynamic, parachute, engine, navigation sensor, flight software and landing radar models were also included. A set of dispersions for each model, as well as for additional simulation input parameters, were also included in order to provide a statistical, Monte Carlo prediction of the EDL system performance. An overview of the pre-flight performance assessments completed, including the various simulation campaigns used, will be provided. Ultimately, this work was critical in the assessment of readiness for InSight launch. A brief description of the use of this simulation in support of flight operations is also discussed.

Robert W Maddock↗

NASA NTRS2024

Investigating the Physical Modification of the Bennu Sample During Entry, Descent, and Landing

On September 24, 2023, the OSIRIS-REx Sample Return Capsule (SRC) entered Earth’s atmosphere and landed in the Utah Test and Training Range (UTTR). Preliminary examination of the returned Bennu sample has confirmed that OSIRIS-REx sample mass exceeds the mission requirement of 60 g of material. The sample consists of particles that range from a few centimeters to microscopic fines. During the SRC’s entry, descent, and landing (EDL) sequence, it may have experienced (i) peak decelerations of 10s of g (ii) tumbling, and (iii) touchdown at approximately 10 m/s, which could have induced physical modification of the sample. In addition, the act of sampling may have altered or biased the physical properties of the collected materials. Here, we investigate the likelihood and extent of physical modification of the sample between collection and return using observations and modeling. This work addresses the mission’s hypothesis 12, which concerns, in part, the modification of the sample during collection and Earth entry.

asteroid↗

NASA NTRSDate not supplied

Entry, Descent, and Landing Analysis for the OSIRIS-REx Sample Return Capsule

The Origins, Spectral Interpretation, Resource Identification, and Security – Regolith Explorer (OSIRIS-REx) sample return capsule (SRC) returned to Earth on September 24, 2023, safely landing in the Utah Test and Training Range (UTTR). To ensure a safe and successful landing, a pair of high-fidelity EDL simulations, based on the Program to Optimize Simulated Trajectories (POST) architecture, were used to regularly assess the latest orbit determination (OD) solution from the navigation team, making predictions on Entry, Descent, and Landing (EDL) performance and SRC landing location. The results from these analyses fed into the decision processes for the final trajectory correction maneuvers (TCM’s) and SRC release. The models and methods of analysis will be discussed and a comparison of the final pre-entry landing prediction against the observed landing location will be presented along with an assessment of the best estimates of day-of-entry environmental conditions.

Scott R Francis↗

NASA NTRSDate not supplied

DAVINCI Venus Entry, Descent, and Landing Modeling and Simulation

The Deep Atmosphere Venus Investigation of Noble gases, Chemistry, and Imaging (DAVINCI) mission will launch in June 2029 and explore Venus via two flybys and a probe landing scheduled for June 2031. The goals of the mission are to study the origin, evolution, and current state of Venus and to understand if it was habitable at a point in the past. The entry, descent, and landing (EDL) concept of operations of the probe leverages on the successful Pioneer Venus large probe mission. The science objectives of the mission levy certain requirements on the EDL system, such as landing in the scientifically important Alpha Regio Tessera and telemetering several gigabytes of instrumentation data to the orbiting relay spacecraft before the probe impacts the surface. In order to optimize the EDL sequence of the lander and to verify key driving requirements, a six degree of freedom EDL flight mechanics simulation has been created based on the best available aerodynamic and atmospheric models valid for Venus. This paper describes the EDL modeling and simulation and summarizes the current flight mechanics results for the mission.

Soumyo Dutta↗

NASA NTRSDate not supplied

DAVINCI Venus Entry, Descent, and Landing Modeling and Simulation

The Deep Atmosphere Venus Investigation of Noble gases, Chemistry, and Imaging (DAVINCI) mission will launch in June 2029 and explore Venus via two flybys and a probe landing scheduled for June 2031. The goals of the mission are to study the origin, evolution, and current state of Venus and to understand if it was habitable at a point in the past. The entry, descent, and landing (EDL) concept of operations of the probe leverages on the successful Pioneer Venus large probe mission. The science objectives of the mission levy certain requirements on the EDL system, such as landing in the scientifically important Alpha Regio Tessera and telemetering several gigabytes of instrumentation data to the orbiting relay spacecraft before the probe impacts the surface. In order to optimize the EDL sequence of the lander and to verify key driving requirements, a six degree of freedom EDL flight mechanics simulation has been created based on the best available aerodynamic and atmospheric models valid for Venus. This paper describes the EDL modeling and simulation and summarizes the current flight mechanics results for the mission.

Soumyo Dutta↗