Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Workability of High-Strength Automobile Steel at High Temperatures Using Hot Processing Maps and Electron Backscatter Diffraction

Hot deformation behavior of a high-strength steel Docol 1500 Bor was investigated by compression tests on a thermal–mechanical simulator Gleeble 3500. The workability of tested steel was analyzed by building processing maps at three strains based on the test results of flow stresses. The essential deformation mechanism was further studied based on the deformation texture analysis on a scanning electronic microscope with a TSL-OIM™EBSD system. It was found that that strain can affect the workability of the tested steel remarkably. At the engineering strain of 0.6, obvious textures in martensite mainly include recrystallization textures <110>//ND and other texture components <110>//RD and {001} <100>, etc. Dynamic recrystallization and recrystallization texture component <111>//ND in deformed austenite can contribute to increasing the workability of a steel Docol 1500 Bor. Finally, the optimized deformation conditions of the tested steel were obtained.

36 MATERIALS SCIENCE↗

High-temperature deformation behavior and microstructural characterization of high-Mn bearing titanium-based alloy

Highlights: • The hot deformation behavior of a biomedical low-cost Ti-10Mn alloys was studied. • The flow curves of the alloy display periodic serrations attributed to dynamic strain aging. • Mn alloying increases the activation energy to 243 kJ/mol compared to pure Ti. • The dynamic recovery is more effective than dynamic recrystallization at hot deformation. - Abstract: Ti-Mn alloys exhibit an excellent potential for biomedical applications as well as structural engineering applications, especially in the aerospace industry. In order to control and enhance grain structure during the manufacturing of Ti-Mn alloys and thereby help to enhance mechanical properties such as strength and toughness, we studied the hot-deformation behavior of βTi-10Mn alloys. Isothermal compression tests were conducted in the strain rate range of 0.01–10 s{sup −1} and temperatures in the range of 850–1000 °C using a Gleeble thermomechanical simulator. High-temperature flow stress curves exhibited discontinuous yielding and pronounced periodic serrations without any strain hardening during compression straining of these alloys. Such peculiar behavior of this alloy is due to active dynamic strain aging in its β-bcc structure. Metallographic observations by electron-backscattered diffraction (EBSD) analysis revealed that dynamic recovery (DRV) is more active than continuous dynamic recrystallization (CDRX) when the alloy is deformed at high strain rates, i.e. higher than 1 s{sup −1}. Furthermore, the constitutive behavior of the alloy was modeled and the apparent hot-deformation activation energy of the alloy was estimated to be 243 kJ/mol, which is ~60% higher than the self-diffusion energy in pure titanium.

36 MATERIALS SCIENCE↗

Effect of 0.1 wt.% Co on the Hot Deformation and Toughness of Fine-Grained Low-Carbon Steel at Sub-zero Temperatures

The effect of 0.1 wt.% Co on the hot deformation behavior of fine-grained low-carbon microalloyed steel was investigated at temperatures of 850-1200 °C and a strain rate of 5 s{sup −1}. Furthermore, the toughness of the steel with and without Co at sub-zero temperatures was evaluated. The results suggest that the addition of 0.1 wt.% Co increases the flow stress and delays the occurrence of dynamic recrystallization (DRX) at the same deformation temperature and strain. The DRX fraction of steel specimens without and with 0.1 wt.% Co was about 67.4 and 43.9% at 850 °C, respectively. Then, it increased to 100% at 1100 °C. Compared with steel without Co, cementite particles in the tempered sorbite of steel with 0.1 wt.% Co decreased in size but increased in quantity, yield strength increased from 756 to 787 MPa, and Charpy V-notch energy at − 20 and − 50 °C improved from 69 and 41 to 102 and 65 J, respectively. The fracture morphology and crack propagation characteristics were consistent with the variation in impact energy.

36 MATERIALS SCIENCE↗

Effect of Hot Deformation on Texture and Microstructure in Fe-Mn Austenitic Steel During Compression Loading

Hot compression tests of a new high-Mn austenitic steel were carried out at deformation temperatures of 700, 800, 900, and 1000 °C under strain rate of 0.01 s{sup −1}. The hot deformation behavior was investigated by the analyses of flow curves, texture, and deformed microstructures. Microstructures of the deformed specimens and macrotexture were examined using electron backscatter diffraction and x-ray diffraction methods, respectively. The results showed that the flow stress depended strongly on the deformation temperature and decreased by increasing deformation temperature. The microstructural evidence indicated that the dynamic recrystallization (DRX) process of experimental steel was initiated at 800 °C with necklace structure. The volume fraction of DRX grains was considerably increased by increasing deformation temperature to 1000 °C. Texture of the DRX grains tended to become a weak texture and was associated with the formation of Goss and R-Cube components. Meanwhile, martensitic transformation was detected in the hot-deformed austenite. The martensitic transformation was the most difficult in the DRX grains because of the effect of small grain size. The tendency of transformation was decreased after compression at 1000 °C.

36 MATERIALS SCIENCE↗

Isothermal deformation and spheroidization mechanism of (TiB + La2O3)/Ti composites with different initial structures

Highlights: • Different initial microstructures were obtained through designed heat treatment. • Refined lamellar microstructures promoted dynamic recrystallization. • The spheroidization mechanism was attributed to dynamic recrystallization. • The micron TiB and submicron La{sub 2}O{sub 3} impeded dislocation movement. (TiB + La{sub 2}O{sub 3})/Ti composites with different initial structures were obtained through designed heat treatment. The isothermal deformation and spheroidization mechanisms of (TiB + La{sub 2}O{sub 3})/Ti composites with different initial structures were investigated. Initial structures were refined as the heat treatment temperature decreased. Simultaneously, the quenching and reheating resulted in finer α lamella colonies and α interlamellar spacing compared to the furnace cooling. The flow resistance of furnace cooled samples was lower than the quenched and reheated samples in terms of flow stress data. Following the deformation at 920 °C, the furnace cooled samples demonstrated lamellar α phase and partial spheroidized structure. Moreover, the spheroidization mechanism was similar to the boundary splitting model. Recrystallized grains of approximately 1 μm in diameter were obtained in the quenched and reheated sample following deformation at 920 °C. The spheroidization mechanism was attributed to the development of finer needles through quenching and reheating, as well as to subsequent dynamic recrystallization during the hot deformation. Additionally, the dislocation movement was blocked by the reinforcements on account of the composites with micron TiB and submicron La{sub 2}O{sub 3} during the hot deformation. Furthermore, the reinforcements could facilitate the dynamic recrystallization (DRX) of the α phase.

36 MATERIALS SCIENCE↗

Hot Deformation Behavior and Microstructural Evolution of Antibacterial Austenitic Stainless Steel Containing 3.60% Cu

Hot deformation behavior of as-cast antibacterial austenitic stainless steel containing 3.60% copper was investigated in a temperature range of 900-1150 °C and strain rate range of 0.01-20 s{sup −1}. At strain rates higher than 1 s {sup −1}, the flow stress curves were corrected considering adiabatic heating. Kinetic analysis indicated that the hot deformation activation energy of steel was 376.02 kJ mol{sup −1}. The microstructural evolution under different temperatures was observed by optical microscopy. The nucleation sites for recrystallization and different orientations and twin ratios under different strain rates were analyzed by electron backscatter diffraction. The results showed that hot deformation was dominated by continuous dynamic recrystallization in the high-temperature and high-strain-rate region (1050-1150 °C, 1-20 s{sup −1}). On increasing the temperature and strain rate, the degree of recrystallization and twinning increased simultaneously. These phenomena promoted one another. Thus, the volume fraction of the recrystallized and twinned grains increased with the addition of Cu.

36 MATERIALS SCIENCE↗

Effect of Aluminum Alloying on the Hot Deformation Behavior of Nano-bainite Bearing Steel

Interest in using aluminum in nano-bainite steel, especially for high-carbon bearing steel, is gradually growing. In this study, GCr15SiMo and GCr15SiMoAl steels are introduced to investigate the effect of Al alloying on the hot deformation behavior of bearing steel. Results show that the addition of Al not only notably increases the flow stress of steel due to the strong strengthening effect of Al on austenite phase, but also accelerates the strain-softening rates for its increasing effect on stacking fault energy. Al alloying also increases the activation energy of deformation. Two constitutive equations with an accuracy of higher than 0.99 are proposed. The constructed processing maps show the expanded instability regions for GCr15SiMoAl steel as compared with GCr15SiMo steel. This finding is consistent with the occurrence of cracking on the GCr15SiMoAl specimens, revealing that Al alloying reduces the high-temperature plasticity of the bearing steel. On the contrary, GCr15SiMoAl steel possesses smaller grain size than GCr15SiMo steel, manifesting the positive effect of Al on bearing steel. Attention should be focused on the hot working process of bearing steel with Al.

36 MATERIALS SCIENCE↗

A Comparative Study of Constitutive Characteristics and Microstructure Evolution between Uniaxial and Plane Strain Compression of an AA6061 Alloy

The hot deformation behavior of an AA6061 alloy was comparatively studied by uniaxial compression (UC) and plane strain compression (PSC) in the temperature range of 300-450 °C and strain rate range of 0.01-5 s{sup −1}. The processing maps were constructed based on a dynamic materials model, and the associated microstructures were observed. Under the same deformation conditions, the flow stress of the AA6061 alloy during PSC is higher than that during UC, which can be characterized by the Zener–Hollomon (Z) parameter in a hyperbolic sine-type equation with an activation energy Q of 175.2 kJ mol{sup −1} and 201.9 kJ mol{sup −1}, respectively. In addition, the instability domain is narrower under PSC compared to that under UC. The observed microstructures also indicate that as the Z value decreases, the tendency of dynamic recrystallization increases during PSC. The softening mechanisms in the AA6061 alloy after PSC and UC mainly consist of the dynamic recovery that is accompanied by a slight dynamic recrystallization. The optimum parameters are in the temperature range of 360-450 °C and strain rate range of 0.03-0.3 s{sup −1} for UC, and for PSC, the optimum parameters are in the temperature range of 320-400 °C and strain rate range of 0.01-0.05 s{sup −1}.

36 MATERIALS SCIENCE↗

Effects of Roughing on Finish Rolling Simulations in Microalloyed Strip Steels

The effects of a roughing pass in hot rolling simulations were assessed in VN and Nb-Ti steels. Continuous cooling phase transformation temperatures, flow curves, softening mechanisms (dynamic transformation DT and dynamic recrystallization DRX), and deformed microstructure morphologies were analyzed. The application of one or more roughing passes eliminates the effects of prior microstructural history and ensures that all stock material experiences equivalent hot working conditions and state of the microalloying elements. It has been shown that roughing in hot simulation has the following positive influences: (1) provide more reliable flow stress data; (2) give greater consistencies and accuracy in analysis of softening mechanisms giving three distinct regimes (DT regime at temperatures below 800 °C, DT/DRX inter-mode regime between 800 and 950 °C and DRX regime for temperatures above 950 °C for VN steel); (3) promotion of softening mechanisms as evidence by low critical strains (ε{sub c DT} was within the range 0.08-0.12, while for finishing-only pass, the ε{sub c DT} was in the range of 0.11-0.14 at ε-dot =0.1 s{sup −1}); (4) for roughing and finishing schedules, DT was verified to occur at temperatures 117 and 133 °C above Ae{sub 3} for VN steel and Nb-Ti steel, respectively, compared to the F-only schedules which showed that DT can only occur at temperatures below the Ae{sub 3}; (5) RF schedules promoted uniform microstructural morphologies compared to inhomogeneous microstructures realized in F-only schedules.

36 MATERIALS SCIENCE↗

Size effects of primary/secondary twins on the atomistic deformation mechanisms in hierarchically nanotwinned metals

A series of large-scale molecular dynamics simulations have been performed to investigate the tensile properties of nanotwinned (NT) copper with hierarchically twinned structures (HTS). For the same grain size d and the same spacing of primary twins {lambda}{sub 1}, the average flow stress first increases as the spacing of secondary twins {lambda}{sub 2} decreases, reaching a maximum at a critical {lambda}{sub 2}, and then decreases as {lambda}{sub 2} becomes even smaller. The smaller the spacing for {lambda}{sub 1}, the smaller the critical spacing for {lambda}{sub 2}. There exists a transition in dominating deformation mechanisms, occurring at a critical spacing of {lambda}{sub 2} for which strength is maximized. Above the critical spacing of {lambda}{sub 2}, the deformation mechanisms are dominated by the two Hall-Petch type strengthening mechanisms: (a) partial dislocations emitted from grain boundaries (GBs) travel across other GBs and twin boundaries (TBs); (b) partial dislocations emitted from TBs travel across other TBs. Below the critical spacing of {lambda}{sub 2}, the deformation mechanism is dominated by the two softening mechanisms: (a) Partial dislocations emitted from boundaries of the primary twins travel parallel to the TBs of the secondary twins, leading to detwinning of the secondary twins; (b) Boundaries of the primary twins shift entirely, leading to thickening in one part of primary twins and thinning in the other part of primary twins. The present results should provide insights to design the microstructures for reinforcing the mechanical properties in the NT metals with HTS.

36 MATERIALS SCIENCE↗

Effects of processing defects on the dynamic tensile mechanical behavior of laser-solid-formed Ti-6Al-4 V

Highlights: • Tensile tests are conducted under coupled effects of strain rate and temperature. • Defects act as crack initiation and propagation sites for dynamic tensile fracture. • Dynamic tension-compression asymmetry is due to different behaviors of defects. • Different deformation of defects results in tensile mechanical anisotropy. • Mechanical anisotropy and asymmetry are sensitive to strain rate and temperature. - Abstract: The initial processing defects, i.e. voids, lack-of-fusion pores and inclusions, are the inevitable and unique microstructural features in the Ti-6Al-4 V (Ti64) alloy manufactured by laser solid forming (LSF). This study was to gain insight into the influences of these processing defects on the tensile thermomechanical response of the material under various strain rates of 0.001/s, 500/s, 1000/s and 3000/s, and under a wide range of temperatures from 298 K to 1273 K. The drastic effects of processing defects on the flow stress were founded to be susceptible to tensile loading and increase with the increasing strain rate. The SEM analysis was carried out to further understand the effect of initial processing defects on the dynamic fracture behavior. These processing defects, such as voids and lack-of-fusion pores, are the most vulnerable position to release impact energy instantaneously and then evolve into the initiation site and propagation path for dynamic tensile crack. The tensile crack under high strain rate and high temperature propagates through the columnar prior-β grain boundary α colony. It was analyzed that the typical tension-compression asymmetry in strength is positively associated with the strain rate in the Ti64 alloy by LSF. Such asymmetry is due to the differences in the deformation mechanism of processing defects and in the activated slip system under tensile and compressive loading. Additionally, the anisotropy of the mechanical property was discussed by examining the positive strain rate effects in two orientations (i.e., perpendicular and parallel to the crystal growth direction). This anisotropy is caused by different mechanical behaviors of lack-of-fusion defects and β grain boundary α colony in different orientations.

36 MATERIALS SCIENCE↗

The strain path dependence of plastic deformation response of AA5754: Experiment and modeling

This work presents modeling of experiments on a balanced biaxial (BB) pre-strained AA5754 alloy, subsequently reloaded uniaxially along the rolling direction and transverse direction. The material exhibits a complex plastic deformation response during the change in strain path due to 1) crystallographic texture, 2) aging (interactions between dislocations and Mg atoms) and 3) recovery (annihilation and re-arrangement of dislocations). With a BB prestrain of about 5 %, the aging process is dominant, and the yield strength for uniaxially deformed samples is observed to be higher than the flow stress during BB straining. The strain hardening rate after changing path is, however, lower than that for pre-straining. Higher degrees of pre-straining make the dynamic recovery more active. The dynamic recovery at higher strain levels compensates for the aging effect, and results in: 1) a reduction of the yield strength, and 2) an increase in the hardening rate of re-strained specimens along other directions. The yield strength of deformed samples is further reduced if these samples are left at room temperature to let static recovery occur. The synergistic influences of texture condition, aging and recovery processes on the material response make the modeling of strain path dependence of mechanical behavior of AA5754 challenging. In this study, the influence of crystallographic texture is taken into account by incorporating the latent hardening into a visco-plastic self-consistent model. Different strengths of dislocation glide interaction models in 24 slip systems are used to represent the latent hardening. Moreover, the aging and recovery effects are also included into the latent hardening model by considering strong interactions between dislocations and dissolved atom Mg and the microstructural evolution. These microstructural considerations provide a powerful capability to successfully describe the strain path dependence of plastic deformation behavior of AA5754.

36 MATERIALS SCIENCE↗

Additive manufacturing of an ultrastrong, deformable Al alloy with nanoscale intermetallics

Abstract Light-weight, high-strength, aluminum (Al) alloys have widespread industrial applications. However, most commercially available high-strength Al alloys, like AA 7075, are not suitable for additive manufacturing due to their high susceptibility to solidification cracking. In this work, a custom Al alloy Al 92 Ti 2 Fe 2 Co 2 Ni 2 is fabricated by selective laser melting. Heterogeneous nanoscale medium-entropy intermetallic lamella form in the as-printed Al alloy. Macroscale compression tests reveal a combination of high strength, over 700 MPa, and prominent plastic deformability. Micropillar compression tests display significant back stress in all regions, and certain regions have flow stresses exceeding 900 MPa. Post-deformation analyses reveal that, in addition to abundant dislocation activities in Al matrix, complex dislocation structures and stacking faults form in monoclinic Al 9 Co 2 type brittle intermetallics. This study shows that proper introduction of heterogeneous microstructures and nanoscale medium entropy intermetallics offer an alternative solution to the design of ultrastrong, deformable Al alloys via additive manufacturing.

Science & Technology - Other Topics↗

Kinetics of Static Strain Aging in Polycrystalline NiAl-based Alloys

The kinetics of yield point return have been studied in two NiAl-based alloys as a function of aging time at temperatures between 300 and 700 K. The results indicate that the upper yield stress increment, Delta sigma(sub u) (i.e., stress difference between the upper yield point and the final flow stress achieved during prestraining), in conventional purity (CP-NiAl) and in high purity carbon-doped (NiAl-C) material first increased with a t(exp 2/3) relationship before reaching a plateau. This behavior suggests that a Cottrell locking mechanism is the cause for yield points in NiAl. In addition, positive y-axis intercepts were observed in plots of Delta sigma(sub u) versus t(exp 2/3) suggesting the operation of a Snoek mechanism. Analysis according to the Cottrell Bilby model of atmosphere formation around dislocations yields an activation energy for yield point return in the range 70 to 76 kJ/mol which is comparable to the activation energy for diffusion of interstitial impurities in bcc metals. It is, thus, concluded that the kinetics of static strain aging in NiAl are controlled by the locking of dislocations by Cottrell atmospheres of carbon atoms around dislocations.

Weaver, M. L.↗

Investigation of Thermal Stress Convection in Nonisothermal Gases Under Microgravity Conditions

Microgravity conditions offer an environment in which convection in a nonisothermal gas could be driven primarily by thermal stress. A direct examination of thermal stress flows would be invaluable in assessing the accuracy of the Burnett terms in the fluid stress tensor. We present a preliminary numerical investigation of the competing effects of thermal stress, thermal creep at the side walls, and buoyancy on gas convection in nonuniformly heated containers under normal and reduced gravity levels. Conditions in which thermal stress convection becomes dominant are identified, and issues regarding the experimental measurement of the flows are discussed.

Mackowski, Daniel W.↗

Columnar Grain-driven Plasticity and Cracking in Nanotwinned FCC Metals

The mechanisms of strengthening and plasticity in columnar-grained metals with preferentially oriented nano-sized twins have been examined traditionally by considering dislocation processes, but rarely from the perspective of grain boundary (GB) deformation. Here, the effects of GB strain accommodation on plastic deformation in four different columnar-grained nanocrystalline nanotwinned (nt) face-centered-cubic metals (Cu, Ag, Al, and Ni) were studied by large-scale molecular dynamics simulations. It is observed that in tensile deformation parallel to coherent twin boundaries (CTBs), the dislocation mechanisms in each metal are identical and associated with GB emissions of jog and threading dislocations at small and large CTB spacings, respectively. However, CTB strengthening effects are increasingly more pronounced in columnar-grained nt metals as their shear modulus increases, which is rationalized by the dependence of GB stress concentrations on twin size, metal type and strain rate. Also, while flow stresses in nt-Cu, nt-Ag, and nt-Al metals increase linearly with decreasing CTB spacing, a maximum strength limit is reached in nt-Ni below a critical CTB spacing of 6 nm. The strength limit in nt-Ni results from columnar GB cracking induced by prominent GB sliding. For columnar-grained microstructures, GB sliding is equivalent in nt-Ag and nt-Al and slightly lower in nt-Cu but markedly higher in nt-Ni. These findings underscore the importance of new GB deformation mechanisms on plasticity and fracture in columnar-grained nt metals and enrich our understanding of CTB strengthening in fcc metals synthesized in the literature.

36 MATERIALS SCIENCE↗

Interfacial sliding near a free surface in a fibrous or layered composite during thermal cycling

This paper presents a simple shear lag model of interfacial sliding at a free surface in a layered or continuous fiber composite. The interface is characterized by a critical interfacial shear stress, tau0, which might represent the critical stress for frictional sliding at a weakly bonded interface, or the shear flow stress of a thin ductile interface layer at a well bonded interface. The history, during heating and cooling, of the relative normal displacement of the reinforcing inclusions and the matrix on a free surface cut normal to the inclusions is calculated and shown to depend on both the absolute value and the temperature dependence of tau0, as well as on the magnitudes of the bulk residual stresses. The variety of possible displacement histories suggests that they are a rich source of information about tau0 and the residual stresses.

Cox, B. N.↗

Stress and strain relaxation in magnesium AZ31 rolled plate: In-situ neutron measurement and elastic viscoplastic polycrystal modeling

Continuous mechanical tests with strain holds (stress relaxation) and with stress holds (strain relaxation) are performed simultaneously with in-situ neutron measurements to analyze the mechanisms of stress and strain relaxation in Mg AZ31 rolled plate. A dislocation activity based constitutive model, accounting for internal stress statistical distributions, is proposed and implemented into an elastic viscoplastic self-consistent (EVPSC) framework to simultaneously describe both stress and strain relaxation. The model captures the experimental data in terms of macroscopic stress strain curves, evolution of stress and strain during holding, as well as evolution of the internal elastic strains. Model results indicate that the magnitude of the stress relaxed during strain holding is dependent on both, the magnitude of the flow stress and the spread of the resolved shear stress distribution. The magnitude of strain accumulated during stress holding is, on the other hand, dependent on the magnitude of the hardening rate and on the spread of the resolved shear stress distribution. Furthermore, the internal elastic strains are directly correlated with the stress state, and hence the stress relaxation during strain holds has a greater influence on the lattice strains than strain relaxation during stress holds.

36 MATERIALS SCIENCE↗