Search NASA⌕ Search

SEARCH · Search NASA

Results for “Focused Ion Beam”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Tuning working potential of silicon-phosphorus anode via microstructure control for high-energy lithium-ion batteries

The primary research on anode materials of lithium-ion batteries have been focused on increasing the specific capacity, while the working potential that is also closely related to the practical energy density of batteries has been paid much less attention. In this paper, starting from micrometer-sized silicon and black phosphorus, we have reported a high-energy silicon-phosphorus/carbon anode (denoted as mSPC) via a high-energy ball milling process, which demonstrates an average discharge working potential of 0.3 volts versus lithium, together with a high reversible capacity of > 2000 mAh/g, high initial coulombic efficiency of 84%, excellent cycle stability, and superior rate capability up to 15 A/g. Furthermore, in situ focused-ion-beam scanning electron microscopy reveals that the volume change of the mSPC anode during repeated (de) lithiation is effectively alleviated. In contrast, starting from nanometer-sized silicon, the resulted anode (denoted as nSPC) not only presents a lower reversible capacity (~1200 mAh/g), but also exhibits a higher charge/discharge working potential, leading to reduced energy density. Our results indicate the importance of composition/structure control in tailoring the working potential and specific capacity of alloying-type anodes towards high-energy lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Investigations of Polymethacrylate Tribochemical Films Using X-Ray Spectroscopy and Optical Profilometry

This study investigates the elemental composition and surface morphology of solid tribochemical films formed on steel surfaces. The reversible addition-fragmentation chain transfer (RAFT) method was used to synthesize nine different metal-free polymers, which were blended into commercial base oils. The polymers were either homopolymers of dodecyl methacrylate and ethylhexyl methacrylate or were co-polymers of these monomers with six polar monomers. After tribological testing at 100 degrees C using the ball-on-flat geometry, the resulting tribochemical films were imaged using scanning electron microscopy (SEM) and optical microscopy. The resulting tribochemical films have thicknesses around 50-100 nm. Two of the films corresponding to small (P1-imidazole-containing copolymer) and large (P3-less polar homopolymer) wear were cross-sectioned using focused ion beam (FIB) and analyzed for elemental composition using energy-dispersive X-Ray (EDX) mapping. Oxygen and nitrogen enrichment was observed, consistent with the relative chemical composition of the precursor polymers. Transmission electron microscopy (TEM) evidence suggests that at the worn surface, some organic elements penetrate or are mixed into the steel substrate giving an interlocking appearance. The two samples examined with TEM showed that P1 tribofilm is diffused or mixed with the steel substrate more so than P3, suggesting a stronger affinity and contact during tribofilm formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Inhibition of Micro-pitting by Tribofilm-Forming ZrO 2 Nanocrystal Lubricant Additives: A Micro-pitting Rig and Transmission Electron Microscope Study

The drive to reduce fuel consumption in transportation has encouraged the emergence of low viscosity lubricants to reduce viscous losses in the engine, drivetrain, and other components. However, viscosity reduction increases the risk of surface damage, thus motivating the development of new anti-wear (AW) additives. Capped ZrO 2 nanocrystals (NCs) in base oils have been shown to form AW tribofilms within microscale sliding contacts. However, the potential of ZrO 2 NCs to protect surfaces subjected to rolling-sliding contact from macroscale damage, such as micro-pitting, remains unexplored. Here, we explore the ability of ZrO 2 NCs to form protective tribofilms under harsh conditions using a micro-pitting rig (MPR), consisting of a three ring-on-roller configuration. The experiments were conducted in polyalphaolephin (PAO) base oil, with and without 5 nm diameter ZrO 2 NCs, at two levels of slide-to-roll ratio (SRR) (30% and 0%) and at variable test durations up to long durations (119 h). MPR results showed the use of ZrO 2 NCs gives rise to the formation of a tribofilm covering the roller surfaces and decreases the initiation and propagation of micro-pits compared to tests in pure PAO base stock. Transmission electron microscopy (TEM) performed on focused ion beam (FIB) milled cross-sectional samples of the roller surfaces revealed the growth of dense and 50–100 nm thick ZrO 2 -based tribofilms independent of (SRR), indicating the potential for robust micro-pitting fatigue protection. Nevertheless, small cracks localized within the near surface region of the roller tested at the most severe conditions (30% SRR and 119 h) were observed. The initiation of these cracks was directly related to the presence of manganese sulphide (MnS) inclusions in the steel, revealed using TEM combined with energy dispersive spectroscopy (EDS). Furthermore, the results highlight the benefits of the protective tribofilms formed by ZrO 2 NCs and suggest approaches for further optimizing their use.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Chemo-Mechanics of α-V 2 O 5 During Lithiation and Implications for Rechargeable Battery Cathodes

Chemo-mechanical degradation of layered oxide electrodes is strongly influenced by crystallographic anisotropy, local stress evolution, and ion insertion, yet the intrinsic mechanical response of layered materials remains incompletely understood. Indeed, most prior studies have focused on polycrystalline materials but single crystals enable direct observation of coupling between anisotropic ion diffusion and mechanical response. This study aims to determine how crystallographic anisotropy and lithiation affect deformation, fracture, and mechanical properties in single-crystal V 2 O 5 , and compares this behavior with polycrystalline counterparts. Polycrystalline V 2 O 5 thin films and single-crystal α-V 2 O 5 were studied using nanoindentation, scanning electron microscopy, focused ion beam cross-sectioning, and Raman spectroscopy. Single crystals were tested in pristine and chemically lithiated states, including experiments in which crystals were first plastically deformed via nanoindentation and subsequently lithiated. Polycrystalline films exhibited significantly higher hardness and elastic modulus than single crystals. Single crystals indented normal to the exposed (001) basal plane exhibited pronounced anisotropic deformation, including directional slip, crystallographically-guided cracking, anisotropic crack propagation, interlayer separation, and shear localization. Lithiation caused substantial softening, reduced hardness and modulus, and suppressed displacement bursts during nanoindentation, while previously indented regions showed crack formation and growth upon lithiation. Mechanical behavior of α-V 2 O 5 is strongly governed by crystallographic anisotropy and further altered by lithiation, with pre-existing deformation serving as a strong driver of fracture during ion insertion. These findings illuminate the coupling among ion insertion, deformation, and fracture in layered oxides and provide a basis for understanding and mitigating mechanical failure in electrochemical energy-storage materials.

Anisotropy↗
DOE OSTI2020

Grain Boundary and Lattice Fracture Toughness of UO 2 Measured Using Small-Scale Mechanics

Small-scale mechanical testing has been used to isolate the properties of individual grain boundaries and regions of the lattice in undoped UO 2 polycrystals. Notched microcantilever specimens were prepared by focused ion beam milling and tested in bending. Fracture toughness values were calculated from finite element analysis of the sample geometry at fracture load using the J-integral method. Lattice and grain boundary fracture toughness values of 1.17 ± 0.16 MPa m 1/2 and 1.08 ± 0.08 MPa m 1/2 , respectively, were obtained. The similarity between the lattice and grain boundary fracture toughness values is consistent with the preference for transgranular room-temperature fracture in UO 2 . The grain boundary and lattice fracture toughness values also agree well with the toughness of dense polycrystals, which suggests that microstructural-scale toughening mechanisms are limited in such samples.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Quantitative study of the effect of grain boundary parameters on the slip system level Hall-Petch slope for basal slip system in Mg-4Al

Several theoretical studies have reported that the geometry and structure of grain boundaries in polycrystalline materials could impose a significant effect on the Hall-Petch slope. However, experimental observations are primarily limited by the ability of the techniques to accurately quantify the grain boundary strength and validate these theoretical models. Using high-resolution electron backscatter diffraction (HR-EBSD), the local stress tensor ahead of a slip band blocked by a grain boundary was quantified and coupled with a continuum dislocation pile-up model to assess the barrier strength of specific grain boundaries to specific slip systems, referred to as micro-Hall-Petch coefficient. For basal slip system in a deformed Mg-4Al alloy, the micro-Hall-Petch coefficient ($k^{basal}_{μ}$) varied significantly, from 0.054 to 0.184 MPa - m 1/2 for nine different grain boundaries. These results were correlated with geometric descriptors of the respective grain boundaries, with three-dimensional GB profile additionally measured via focused ion beam milling. It was found that the angle between the two slip plane traces on the grain boundary plane was the most sensitive parameter affecting $k^{basal}_{μ}$, followed by the angle between the slip directions. A functional form for calculation of $k^{basal}_{μ}$ depending on these two angles is proposed to augment crystal plasticity constitutive models with slip resistance dependent on some measure of the grain size. The method allows a new pathway to calibrate grain size strengthening parameters in crystal plasticity models, allowing further computational investigations of the interrelationship between texture, grain morphology, and the Hall Petch effect.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Transformations of Ti-5Al-5V-5Cr-3Mo powder due to reuse in laser powder bed fusion: A surface analytical approach

Reactive Ti-5Al-5 V-5Cr-3Mo (Ti5553) alloy feedstock powder is used in laser powder-bed fusion (LPBF). Due to the large quantity of powder necessary for LPBF, powder is reused numerous times under oxidizing environments. Transformations to the powder’s native surface oxide may impact the LPBF process and lead to deviations from expected behavior of printed parts. In this work, we present a multimodal characterization of new and reused powder by combining X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and transmission electron microscopy (TEM) of focused ion beam (FIB)-prepared cross sections of individual powder particles to understand how the surface oxide composition changes, grows, and becomes hydroxylated and hydrated due to reuse. We show that the native oxide film of Ti5553 powder is a hydroxylated mixed oxide composed of TiO 2 and Al 2 O 3 that grows from 5.6 +/- 0.7 nm to 8.3 +/- 1.1 nm due to reuse. Al oxide regions of the surface oxide become more hydroxylated during reuse in comparison to Ti oxide regions. This indicates that an outer oxide of pure TiO 2 may enhance recyclability of Ti5553 powder while the presence of Al oxides may decrease recyclability. Further characterization of surface transformations due to recyclability may eliminate unnecessary variation in LPBF.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Probing Heterogeneity in Bovine Enamel Composition through Nanoscale Chemical Imaging using Atom Probe Tomography

Objective: The aim of this study was to determine the heterogeneity in chemical composition of bovine enamel using atom probe tomography, and thereby evaluate the suitability of bovine enamel as a substitute for human enamel in in vitro dental research. Design: Enamel samples from extracted bovine incisor teeth were first sectioned using a diamond saw and then milled into needle-like samples (<100 nm diameter) by focused ion beam (FIB) coupled with a scanning electron microscope (SEM). The samples were then analyzed in the atom probe to acquire three-dimensional (3D) images and quantify the atomic chemistry and distribution in bovine enamel. Results: For the first time, the atomic-level composition and clustering of major constituents and impurities within bovine enamel were determined and imaged. We discovered that the chemical composition of bovine enamel is spatially inhomogeneous at the atomic scale. The average bulk Ca/P ratio, ~1.4, was in agreement with previously reported literature values from alternative conventional methods. When assessed locally at the atomic scale, the Ca/P ratio varied between 1.1 and 2.03. We also discovered that the Mg impurities were significantly segregated throughout the enamel, and such clustering influenced the variation of Ca/P ratios. The increase in Mg concentrations, near the Mg clusters, correlated with increased Ca and decreased P concentrations. Conclusion: In conclusion, the presented findings of variability in local composition should be taken into account when interpreting dental research results from bovine enamel.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

3D imaging techniques for characterising microcracks in cement-based materials

Concrete inherently contains pores and microcracks that can adversely impact its mechanical properties and long-term durability. However, characterising microcracks is difficult due to their complex, multiscale and three-dimensional (3D) nature. This paper presents an evaluation of 3D imaging techniques for characterising microcracks induced by different mechanisms. Seven cement pastes, mortars and concretes subjected to drying shrinkage, autogenous shrinkage and freeze-thaw cycles were investigated using focused ion beam nanotomography (FIB-nt), broad ion beam serial section tomography (BIB-SST), laser scanning confocal microscopy (LSCM) combined with serial sectioning and X-ray microtomography (μCT). The study shows that the characteristics of microcracks vary significantly depending on exposure conditions. Yet there is no single technique that can capture the entire size range of microcracks from sub to tens of μm within a sufficiently representative sampling volume. The achievable image volume and resolution, and the advantages and disadvantages of each technique are compared and discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fiber/matrix debonding evaluation of SiCf/SiC composites using micropillar compression technique

Third-generation silicon carbide (SiC) composites reinforced by SiC fibers (Hi-Nicalon S [HNS] and Tyranno SA3 [SA3]) are attractive for use in next generation reactors owing to their high strength and chemical inertness at high temperatures, as well as enhanced radiation tolerance under neutron irradiation environments. To optimize composite performance, the interfacial mechanical properties of chemical vapor–infiltrated (CVI) SiC f /SiC composites are investigated in this effort by using a slant interface micropillar compression testing procedure. The micropillar test specimens, containing an inclined pyrolytic carbon (PyC) interphase, are prepared using a focused ion beam. The novel microcompression testing successfully quantifies the debond shear strength and internal friction coefficient of micropillar test samples by using the Mohr-Coulomb formulation. Furthermore, according to four types of SiCf/SiC composite microcompression test results, interfacial properties and debond mechanisms are significantly affected by the PyC layer thickness, the local bonding mechanism of the PyC interphase on the SiC fiber surface, and the surface roughness of fibers. Regardless of PyC thicknesses, SA3-reinforced CVI SiC f /SiC composites are found to have much higher debond shear strengths than HNS-reinforced SiC f /SiC CVI composites. By using this micropillar compression technique alongside analytical methods, we uncover new understandings of PyC interface properties. Additionally, the micropillar test results obtained are correlated with macroscopic mechanical properties of neutron-irradiated CVI SiCf/SiC composites.

42 ENGINEERING↗
DOE OSTI2022

Data on Cu- and Ni-Si-Mn-rich solute clustering in a neutron irradiated austenitic stainless steel

The data presented in this article is supplementary to the research article “Phase instabilities in austenitic steels during particle bombardment at high and low dose rates” (Levine et al.). Needle-shaped samples were prepared with focused ion beam milling from a 304L stainless steel that was irradiated with fast neutrons (E 0.1 MeV) in the BOR-60 reactor at 318 °C to 47.5 dpa. Atom probe tomography (APT) experiments in voltage mode were then conducted on a Cameca LEAP 5000X HR. Atom position, range, and mass spectrum files after reconstruction with Cameca’s IVAS software are included. Cu- and Ni-Si-Mn-rich solute nanoclusters were identified and analyzed using the Open Source Characterization of APT Reconstructions (OSCAR) program. Python code for OSCAR, information on the program’s underlying algorithm, and sample output files are provided. A proximity histogram of a Ni-Si-Mn-rich cluster and a 1D density/solute concentration profile of a Cu-rich cluster are given to demonstrate OSCAR’s analytical functionalities. The provided APT dataset is valuable for benchmarking phase instabilities in neutron-irradiated austenitic stainless steels that occur at high doses. The OSCAR program can be reused to process other APT data sets where solute nanoclustering is of interest.

42 ENGINEERING↗
DOE OSTI2021

Roles of Mn and Co in Ni-rich layered oxide cathodes synthesized utilizing a Taylor Vortex Reactor

It is reported that layered oxides, composed of nickel, manganese, and cobalt (NMC), are sought after as cathode materials which provide improved energy density, cycle life, and safety in commercial lithium ion batteries (LIBs). Increasing Ni contents higher than 80% can provide even higher practical discharge capacities >200 mAh/g and similar to ~4 V discharge potential vs Li/Li + , making them promising cathodes for next generation LIBs. However, rapid capacity fade during cycling and heat-related safety concerns are delaying their successful transition to industry. We report systematic performance optimization of LiNiO 2 , LiNi 0.9 Mn 0.1 O 2 , and LiNi 0.9 Co 0.1 O 2 high Ni layered oxide cathodes synthesized by utilizing a Taylor Vortex Reactor. Co-free LiNi 0.9 Mn 0.1 O 2 cathode showed 200 mAh/g highest discharge capacity at 0.1 C rate with 84% retention after 103 cycles at 0.3C rate while LiNi 0.9 Co 0.1 O 2 cathode showed higher initial but poor cycle life (225 mAh/g highest discharge capacity at 0.1C rate with only 56% capacity retention after 103 cycles at 0.3 C rate. Synchrotron based X-ray diffraction (SXRD), X-ray absorption spectroscopy (XAS) and focused ion beam (FIB) imaging of pristine and cycled cathodes after 103 cycles provided important information on degradation mechanism. The roles of Mn and Co on layered structure formation, charge balance, cationic mixing, and electrochemical performance were elucidated using the crystallographic information from XRD refinement and electronic state analysis from XAS providing valuable information to design future Ni-rich layered oxide cathodes.

25 ENERGY STORAGE↗
DOE OSTI2022

Multimodal study of the impact of stimulation pH on shale pore structure, with an emphasis on organics behavior in alkaline environments

The tight nature of shale formations calls for hydraulic fracturing techniques able of altering the pore architecture to facilitate the production of hydrocarbon resources. The composition, pH, salinity, density and chemistry of Hydraulic Fracturing Fluids (HFF) vary substantially depending on reservoir characteristics. pH is among the most important stimulation fluid properties, ranging from very acidic, for carbonate reservoirs, to basic, in the case of clay-rich formations. pH regulates what geochemical reactions take place between the stimulation fluid and shale, as well as pore architecture alteration. The dissolution of carbonates and pyrite, and the precipitation of common minerals such as barite, gypsum and iron oxides in acidic environments have been extensively documented. In contrast, alkali stimulation environments and the role of organic components have received less attention. This research provides insight into the role of both minerals and organic components during alkaline stimulation, and the resulting pore architecture alterations. Here, a set of reactive experiments are performed using three different shales, with varying organic matter (OM) content, at different pH (3, 6, 8, 10, 12). The analysis of pore architecture alteration induced by the reaction was performed via nitrogen (N2) gas adsorption and Time-Domain Nuclear Magnetic Resonance (TD-NMR). Inductively Coupled Plasma - Optical Emission Spectrometry (ICP-OES) was used to measure the composition of the stimulation fluid post-reaction. The system with a larger impact on the pore architecture (pH 12) underwent a more extensive analysis through the application of Focused Ion Beam Scanning Electron Microscopy (FIB-SEM) and x-ray Diffraction (XRD). Results show that mineral dissolution contributed to the creation of secondary porosity, mainly through dissolution of clays and silicates. We show that the abundance and distribution of organic matter both play a significant role in changes in pore architecture. Most samples showed an increase in inter-organic porosity, likely due to the organic acids within kerogen reacting with the stimulation fluid. Samples with a larger amount and more widespread distribution of organic matter show the most significant alterations. Finally, we also highlight the dissolution process of iron-rich minerals, including framboidal pyrite, as another important source of secondary porosity.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2021

Influence of microstructure on replacement and porosity generation during experimental dolomitization of limestones

Replacement reactions commonly alter the multiscale pore structures of rocks during fluid-rock interactions. Analysis of these processes in various model fluid-rock systems during controlled laboratory experiments provides insights into the origins of microstructures found in natural materials. This study focused on understanding the effects of initial starting material permeability and resultant differences in transport pathways on porosity and mineralogical changes during limestone dolomitization.A series of replacement experiments (32–317 days in duration) have been conducted in which 1.59 cm (5/8 in.) diameter cores of two different limestones were reacted with saturated MgCl2 solutions at 200 °C. The Texas Cream (Austin Chalk) is a high-porosity, high-permeability limestone, whereas both the porosity and permeability of the Carthage Marble (Burlington Limestone) are relatively low. Altered limestones were imaged using scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), Time-of-Flight Secondary Ion Mass Spectrometry (ToF–SIMS) and electron microprobe analysis (EMPA). A representative grain boundary of the low-porosity limestone was targeted for a focused ion beam (FIB) lift-out and characterized using transmission electron microscopy (TEM). These results were coupled with analyses of radial changes in the porosity distribution of the core derived from X-ray and neutron small- and ultra-small angle scattering ((U)SANS/(U)SAXS).The high-porosity/permeability limestone showed a four times faster bulk replacement rate than the lower-porosity/permeability material, and a different mechanism of porosity development. For the low-porosity limestone, a two-stage replacement occurred, with the reacted region of the core consisting of an inner rim in which the limestone was replaced by two calcite-dolomite solid solutions, and an outer rim in which the dolomite was replaced by magnesite. Elongated pores formed along grain boundaries at the initial limestone/dolomite reaction interface, and additional nanometer-scale porosity was formed at the secondary magnesite replacement rim. Grain boundaries were identified as preferential pathways for transport leading to dolomitization and a grain boundary diffusion rate was calculated based on microstructural characterization. In contrast, replacement in the high-porosity limestone was accompanied by porosity generation through replacement of individual grains by dolomite throughout the sample and, in longer runs, magnesite in outer parts of the core. These observations emphasize that both the mechanisms of the replacement reaction and the microstructure and chemistry of the replaced product are contingent on the initial structure of the starting material.

36 MATERIALS SCIENCE↗
DOE OSTI2026

In-situ observations of cyclic deformation in an extruded Mg-2Nd-1Y-0.1Zr-0.1Ca alloy

In this study, the evolution of deformation mechanisms during cyclic loading in an extruded, solution-treated Mg–2Nd–1Y–0.1Zr–0.1Ca alloy was investigated using a combination of in-situ loading, scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and focused ion beam (FIB) nanofabrication. The initial microstructure exhibited a random crystallographic texture with no preferred grain orientation. Flat, rectangular dog-bone specimens were subjected to load-controlled, fully reversed fatigue for 50 cycles, during which the same region was sequentially mapped to track microstructural changes. After 10 cycles of loading deformation twins were observed. During tensile reloading detwinning or narrowing of those twinned regions occurred. After 20 cycles, detwinning ceased and residual twins remained in the material. SEM imaging revealed numerous surface slip traces after cyclic loading. EBSD-assisted slip trace analysis identified the activation of prismatic and pyramidal < c+a> slip systems during low-cycle fatigue. Site-specific scanning transmission electron microscopy (STEM) further revealed that deformation was also accommodated by basal < a> slip and the dissociation of < c+a> dislocations. Center-of-symmetry (COS) analysis confirmed that the dissociation of < c+a> dislocations resulted in the formation of I₁ intrinsic stacking faults after cyclic loading. These findings provide new insights into the complex interplay of dislocation mechanisms governing fatigue deformation in rare-earth-containing Mg alloys.

Cyclic deformation↗
DOE OSTI2026

Cross-slip and easy-glide CRSS in titanium: Theoretical predictions and in-situ TEM measurements

This study investigates the mechanics of prismatic and first-order pyramidal $\langle$a$\rangle$ slip in titanium (Ti), elucidating the physics of easy-glide and cross-slip through a combination of theory and experiments. Screw-character prismatic (Pr) dislocations in Ti are of particular interest because their complex cores can be stable or unstable, leading to activation by either cross-slip or planar glide. To investigate these mechanisms, site-specific micro tensile samples were prepared using focused ion beam (FIB) milling and mounted on a push-to-pull (PTP) device for in-situ transmission electron microscopy (TEM) tensile testing. The in-situ experiments provide direct observations of the onset of dislocation motion and the precise determination of the critical resolved shear stress (CRSS) for the activated mechanisms, and its evolution with load cycling. A comprehensive theory has been developed to predict the CRSS values for easy glide, cross-slip, and multiplication of dislocations. Predicted critical stresses for pyramidal (π)-to-Pr and reverse cross-slip agree closely with the experimental measurements. The latter cross-slip stress is a factor of two higher than that of unobstructed planar slip. The model accounts for overlapping dislocation cores and employs a Wigner-Seitz based cell to evaluate misfit energies. By combining ab initio density functional theory (DFT) with anisotropic elasticity, the framework identifies minimum energy pathways for dislocation glide, which can be intermittent and zig-zag. A simplified expression utilizing (π) and Pr Schmid factor ratios is proposed for critical stress corresponding to (π)-to-Pr cross-slip transition. The results are strongly dependent on crystal orientation, underscoring non-Schmid behavior. Overall, this study explores key critical stress parameters essential for informing higher-scale simulations of plasticity in Ti.

Critical stress↗
DOE OSTI2025

Evaluating the bond strength and fracture mechanisms of cold-sprayed zinc coating on AZ91 magnesium substrate via a combined experimental and computational approach

Magnesium (Mg) alloys are ideal candidates for automotive applications due to their high strength to weight ratio, castability, recyclability etc., however, they lack corrosion and oxidation resistance. Solid-state deposition techniques, such as cold spray, have been demonstrated to enhance their corrosion resistance as it relies on the severe plastic deformation of powder particles upon impact with the substrate to form a metallurgical bond with the substrate and within the coating. At cold sprayed interfaces, a heterogeneous microstructure is formed that includes some porosity, oxides and intermetallics which can significantly affect coating performance. Thus, establishing a direct correlation between the interface microstructure and its properties can aid in designing optimal cold spray parameters. In this study, we investigated the microstructure and mechanical properties of a zinc (Zn) coating deposited on a high pressure die cast (HPDC) AZ91 Mg substrate via high resolution scanning transmission electron microscopy, in situ micro-tensile testing, and finite element method (FEM) modeling. Micro-tensile pillars fabricated using the plasma focused ion beam (PFIB) successfully isolates the coating-substrate interface within the gauge length. The average bond strength of Zn-Mg interface was determined to be ∼140 MPa with failure occurring partially at the interface and mostly into the coatings. A detailed microstructural characterization revealed evidence of a strong metallurgical bonding at the Zn-Mg interface and formation of the C14 MgZn 2 laves phase interlayer resulting in a mixed mode of fracture during the micro-tensile experiments. FEM modeling reveals the stress distribution along the interfaces and suggests that a MgZn 2 layer thickness between 200–400 nm is optimum to increase the bond strength and minimize the triaxiality. Such a site-specific interfacial analysis with correlative computational modeling provides crucial insight into the overall performance of cold spray interfaces.

Bond strength↗
DOE OSTI2021

Micro-mechanical investigation of the thermo-mechanical properties of micro-architectured tungsten coatings

The thermo-mechanical response of micro-architectured tungsten coatings is characterized in the temperature range of 293 to 673 K using both in situ micro-compression experiments inside a scanning electron microscope (SEM) as well as image-based crystal plasticity finite element method (CPFEM) simulations. The experiments were conducted on micropillar-like specimens that were focus ion beam milled into the coatings, while the simulations were conducted on columnar-grained micropillar simulation cells constructed based on the statistics of the coating’s microstructure. The experimental results show that the stress–strain response and deformation mode exhibit a strong temperature-dependence. At room temperature, catastrophic failure is observed shortly after yield and is manifested in the form of intergranular fracture and buckling of individual columnar grains. With increasing temperature, this catastrophic failure is gradually suppressed and the material exhibits a steadier strain hardening response at 693 K. The CPFEM simulations are also shown to be in good agreement with the experimental results, and these simulations indicate that the material response is strongly influenced by the local crystallographic anisotropy and microstructure inhomogeneity. Furthermore, the simulations capture the underlying mechanisms that control the temperature-dependent transition in deformation mode. The current results highlight that the micro-architectured microstructure offers a great combination of excellent mechanical strength and structural integrity at elevated temperatures, which is of importance for high temperature applications.

36 MATERIALS SCIENCE↗