Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel Cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

A comparison of wrought and powder metallurgical FeCrAl claddings under simulated LWR accident transients

Iron-chromium-aluminum (FeCrAl) alloys are potential accident tolerant fuel (ATF) cladding candidates for light-water reactors but are difficult to fabricate as thin-walled tubes via conventional cast-and-wrought routes. Powder metallurgy (PM) offers a manufacturing alternative with improved compositional control, but its transient accident performance has not been directly benchmarked against wrought variants. This study evaluates the burst behavior of commercially developed PM-processed FeCrAl alloys, PM-C26M (Fe-12Cr-6Al-2Mo) and the high precipitate density FA-SMT (Fe-22Cr-5Al-3Mo), under simulated light-water reactor accident transient conditions. Burst testing was conducted using the Severe Accident Test Station with heating rates of 5 °C/s and 50 °C/s and internal pressures ranging from 25 MPa to 100 MPa. PM-C26M reproduced wrought C26M burst behavior within 7–37 °C across the stress range, indicating that PM processing does not compromise transient strength. FA-SMT exhibited markedly higher burst temperatures and reduced heating-rate sensitivity, consistent with its engineered precipitate strengthening. FA-SMT rupture exhibited axial "unzipping" rather than the lateral tearing characteristic of PM- and wrought C26M. Post-test EBSD and fractography indicate that this behavior is strongly correlated with strain-gated intergranular void nucleation associated with the dense precipitate architecture of FA-SMT, a response absent in the comparatively clean PM-C26M matrix and consistent with rupture morphologies reported for oxide-dispersion strengthened (ODS) FeCrAl of similar base-matrix chemistry to PM-C26M. These findings highlight the potential of powder metallurgy as a viable fabrication route for ATF claddings from an accident performance standpoint.

Bell, Sam [ORNL] (ORCID:0000000251905657)↗
DOE OSTI2024

A Eulerian three-fluid flow framework for the study of fuel dispersal behavior under loss-of-coolant accident conditions

As the nuclear industry explores new fuel designs to accommodate increased burnup, studying fuel behavior during loss-of-coolant accidents is essential for ensuring the safe operation of light-water reactors. Here, this study presents a computational model to simulate the intricate three-phase flow dynamics of fuel dispersal following cladding breach, where solid fuel particles and carrier fission gases interact with the surrounding liquid or gas medium. The model utilizes a Eulerian three-fluid framework to depict the phase interaction within interpenetrating continua, treating fragmented fuel as granular material. Closure relationships for bulk-flow properties of the solid phase and detailed interfacial exchange terms in high-temperature, high-speed gas-solid-liquid flow scenarios are proposed. The model was validated using adiabatic experimental results in the literature, focusing on characterizing fuel dispersal behavior during loss-of-coolant accidents conditions. Settlement characteristics of the solids, quantified by the probability distribution of equivalent particles, closely matched probability density functions reported in experimental studies. Key highlights of this study include the theoretical description of a coupled three-phase flow with phase change, interpretation of the high-pressure boundary conditions and insights into the transient behavior of gas-solid-liquid phase dynamics during a simulated high-speed dispersal event.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Considerations for Managing DOE Standard Canisters within an Over-canister as Part of an Integrated Waste Management System PPT

To better enable informed decision making regarding the back-end of the nuclear fuel cycle, the Integrated Waste Management Program within the U.S. Department of Energy, Office of Nuclear Energy (DOE-NE) has been sponsoring research into a comprehensive integrated waste management system (IWMS) that considers all major back-end aspects of the nuclear fuel cycle (i.e., transportation, storage, and disposal). An important aspect of the IWMS is DOE-managed Spent Nuclear Fuel (SNF). DOE and its predecessor agencies have generated, transported, received, stored, and reprocessed SNF at DOE facilities nationwide, and DOE is responsible for managing the SNF currently in its possession. These fuels come from a wide range of reactor types that employ various cladding materials, fuel materials, and enrichments. To enable interim, road-ready dry storage (RRDS) of the wide variety of SNF types found in the DOE inventory, a standardized canister system (i.e., the DOE Standard Canister) was proposed for the packaging demonstration. This robust, welded canister system is designed to confine radionuclides, prevent criticality by precluding content moderation, and satisfy other requirements as part of a larger storage, transportation, and disposal system. While SNF has yet to be loaded into a DOE Standard Canister, DOE Standard Canister designs were included in past storage facility and disposal facility design licensing endeavors. In a renewed effort to evaluate packaging SNF at Idaho National Laboratory (INL) in a RRDS configuration, researchers are planning the RRDS Packaging Demonstration. This demonstration is supplemented by analytical structural, criticality, and material compatibility evaluations that support management of SNF in DOE Standard Canisters, taking advantage of past analysis work to the extent possible. One of the largest differences between the current Packaging Demonstration and past analytical evaluations is the inclusion of an over-canister containing multiple DOE Standard Canisters. For the Packaging Demonstration, DOE Standard Canisters loaded with SNF are planned to be placed in a larger diameter over-canister. The sealed over-canister could then be placed in a storage overpack for onsite storage, or in a transportation overpack for shipment to an offsite storage location or disposal site once one becomes available. This paper examines the relevant considerations and provides a preliminary evaluation of integrating the over-canister configuration into the storage, transportation, and disposal processes of the overall waste management system. For storage and transportation, the over-canister can be considered analogous to a multi-purpose canister (MPC) for commercial SNF. For disposal, the DOE Standard Canisters could be removed from the over-canister and placed in a co-disposal waste package with canisters containing vitrified high-level radioactive waste (HLW) similar to configurations examined previously, or the sealed over-canisters might be capable of direct disposal in a waste package.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Reference Fuel Development for Non-Aluminum Spent Nuclear Fuel Management

The Savannah River Site (SRS) L Area Facility provides for the safe receipt, storage, handling, and shipping of spent nuclear fuel (SNF) and has received more than 47,000 SNF assemblies since 1964. In order to consolidate receipt and storage analysis, L Area criticality safety has historically used several aluminum-clad “reference fuels” to establish bounding storage, handling, and cask loading limits and then applied a reactivity comparison approach to demonstrate that candidate fuels may be processed under the reference fuel limits. Currently, only aluminum-clad SNF from off-site research reactors are transferred on-site. The Accelerated Basin De-Inventory (ABD) program will begin the removal of bundled Non-Aluminum Spent Nuclear Fuel (NASNF) from the L Area disassembly basin for dissolution and disposition, which has driven the need for a non-aluminum reference fuel. This paper discusses the process and results of creating a new fictional homogenous NASNF highly enriched uranium reference fuel, “MITZ,” to be used in nuclear criticality safety evaluations for upcoming SNF disposition operations. Data demonstrating the relationship between neutron multiplication behavior and fuel spacing is generated for the new reference fuel MITZ as well as existing reference fuels representing several types of SNF assemblies.

Reference Fuel↗
DOE OSTI2025

Reference Fuel Development for Non-Aluminum Spent Nuclear Fuel Management

The Savannah River Site (SRS) L Area Facility provides for the safe receipt, storage, handling, and shipping of spent nuclear fuel (SNF) and has received more than 47,000 SNF assemblies since 1964. In order to consolidate receipt and storage analysis, L Area criticality safety has historically used several aluminum-clad “reference fuels” to establish bounding storage, handling, and cask loading limits and then applied a reactivity comparison approach to demonstrate that candidate fuels may be processed under the reference fuel limits. Currently, only aluminum-clad SNF from off-site research reactors are transferred on-site. The Accelerated Basin De-Inventory (ABD) program will begin the removal of bundled Non-Aluminum Spent Nuclear Fuel (NASNF) from the L Area disassembly basin for dissolution and disposition, which has driven the need for a non-aluminum reference fuel. This paper discusses the process and results of creating a new fictional homogenous NASNF highly enriched uranium reference fuel, “MITZ,” to be used in nuclear criticality safety evaluations for upcoming SNF disposition operations. Data demonstrating the relationship between neutron multiplication behavior and fuel spacing is generated for the new reference fuel MITZ as well as existing reference fuels representing several types of SNF assemblies.

Reference Fuel↗
DOE OSTI2026

MARVEL Reactor Fuel Performance Report

The Microreactor Applications Research Validation and EvaLuation (MARVEL) project is producing a high temperature liquid metal-cooled nuclear test bed at Idaho National Laboratory (INL) to ultimately improve the integration of microreactors to end-user applications. This ambitious effort seeks to design, authorize, construct, test, and operate the reactor within five years. In order to construct and operate the MARVEL reactor in a timely manner, the system will utilize materials and component designs which have already been used, qualified, or licensed from previous reactors. The MARVEL reactor will be located at the INL Transient Reactor Test (TREAT) facility in the north high-bay equipment pit and will use the existing 304 stainless steel-clad U-ZrH1.6 pin-type fuel system developed by General Atomics and purchased from TRIGA International. This fuel has been previously qualified under the United States Department of Energy’s (US DOE) Reduced Enrichment for Research and Test Reactors (RERTR) Program. Even though the regulator of the MARVEL reactor is the US DOE, the standards and overall approach recommended by the Nuclear Regulatory Commission is well-defined and utilized here. Following NUREG-1537 regulatory guidance, this report documents the authorization case for the MARVEL fuel system’s application to MARVEL and establishes stable and predictable fuel performance during the most thermophysically unfavorable conditions achievable in the MARVEL reactor. To that end, this report provides a comprehensive survey of the known thermophysical properties, performance, and quantitative relationships associated with the MARVEL reactor fuel element and uses this information to determine its mechanical integrity and risk of reaching unacceptable conditions during the most extreme accident scenarios predicted for the reactor using the most conservative assumptions available. The information contained herein is compiled from a combination of historical reports and peer reviewed scientific publication manuscripts. Known mechanisms under which the fuel is susceptible to failure are highlighted and compared to conditions that could exist in the MARVEL reactor during an unanticipated transient or accident scenario. The two scenarios considered for analysis in this report are (1) an unprotected loss of flow accident and (2) a hypothetical unprotected loss of coolant accident during the loss of flow accident. Preliminary 2D steady-state analyses herein indicate that both fuel-cladding chemical interactions and fuel-cladding mechanical interactions are negligible throughout the fuel’s operational cycle under both normal and high temperature accident scenario conditions. Although higher fidelity 3D time-dependent modeling and simulations are planned, the following may be concluded presently. The MARVEL fuel element maintains its geometric stability and structural integrity during the most extreme accident scenarios predicted for the MARVEL reactor. The hoop stress during the unprotected loss of flow accident reaches about -1.27 MPa; this negative stress indicates that it is compressive rather than tensile. The compressive stress is a result of the NaK pressure on the outside of the fuel element, caused by the restricted thermal expansion of the NaK coolant, exceeding the internal pressures generated inside of the fuel element. The hoop stress generated in the cladding during the unprotected loss of coolant accident reaches a maximum of about approximately 10 MPa, which is nearly an order of magnitude less than the predicted yield strength of the cladding under high-temperature accident scenario conditions. Calculations were compared with results from high performance computational simulations using BISON and are in very close agreement. A conservative MARVEL fuel meat peak temperature limit of 900 °C is recommended presently, which is about 180 °C higher than the peak fuel temperature predicted to occur during the most extreme accident. Based on the known properties and behavior of the MARVEL fuel element, the fuel successfully meets its design and safety requirements under normal and most extreme accident conditions with a large safety margin.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1971

Studies of thermionic materials for space power applications

Service life tests of LC-8 and LC-9 carbide-fueled thermionic converters are discussed. Post operational tests of the converters to show emitter diametric change, microstructures of cladding and fuel, and analysis of fuel composition are described. The fabrication and performance of high temperature thermocouples used in the test procedures are included.

Source record↗
DOE OSTI2024

DISCOVARY PROJECT: Material Background Report

UC/UO 2 composites have been proposed as a next generation fuel for light water reactors (LWRs). Accident tolerant fuels (ATF) have been a focus in the Advanced Fuels Campaign (AFC) to improve the safety and performance of LWRs and includes research and development efforts on the cladding and fuel. The 10 wt.% UC/UO 2 composite fuel was selected as a result of an extensive literature review and was selected due to the improvement of the fuel cycle cost. The inclusion of a UC phase in the composite material improves on the properties of standard UO 2 by increasing the uranium density of the fuel and increasing the thermal conductivity. Significant development has been carried out to refine the processing and sintering parameters and has led to a dense composite without ternary phases present. Characterization of the chemistry and microstructure has been carried out to send ahead of neutron irradiations in the Belgium Research Reactor (BR2) at SCK-CEN.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1973

A fission gas release correlation for uranium nitride fuel pins

A model was developed to predict fission gas releases from UN fuel pins clad with various materials. The model was correlated with total release data obtained by different experimentors, over a range of fuel temperatures primarily between 1250 and 1660 K, and fuel burnups up to 4.6 percent. In the model, fission gas is transported by diffusion mechanisms to the grain boundaries where the volume grows and eventually interconnects with the outside surface of the fuel. The within grain diffusion coefficients are found from fission gas release rate data obtained using a sweep gas facility.

Weinstein, M. B.↗
DOE OSTI2024

Safety Considerations for Advanced Material Irradiation at the Advanced Test Reactor

The Advanced Test Reactor (ATR) is a light water reactor with aluminum-clad driver fuel. A primary mission of the ATR is to support the next generation of nuclear reactors. This support necessarily requires irradiation of advanced materials such as sodium, fuel salts, and metal eutectics. Irradiation of advanced materials in the ATR environment presents a challenge when completing accident analyses and demonstrating compliance to the Safety Analysis Report (SAR). Many advanced materials have the possibility to react with the ATR protective barriers such as the cladding or primary coolant system (PCS) boundary during postulated accident scenarios. Further, molten fuel experiments fall outside of the standard regulatory framework for dose consequence analyses. ATR is currently developing new safety analysis methods to support irradiation of advanced materials. The primary considerations for this development are 1) experiment containment design requirements, 2) primary coolant system response to an experiment containment failure, and 3) dose analyses for molten fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Safety Considerations for Advanced Material Irradiation at the ATR

The Advanced Test Reactor (ATR) is a light water reactor with aluminum-clad driver fuel. A primary mission of the ATR is to support the next generation of nuclear reactors. This support necessarily requires irradiation of advanced materials such as sodium, fuel salts, and metal eutectics. Irradiation of advanced materials in the ATR environment presents a challenge when completing accident analyses and demonstrating compliance to the Safety Analysis Report (SAR). Many advanced materials have the possibility to react with the ATR protective barriers such as the cladding or primary coolant system (PCS) boundary during postulated accident scenarios. Further, molten fuel experiments fall outside of the standard regulatory framework for dose consequence analyses. ATR is currently developing new safety analysis methods to support irradiation of advanced materials. The primary considerations for this development are 1) experiment containment design requirements, 2) primary coolant system response to an experiment containment failure, and 3) dose analyses for molten fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

FAST-1.2.2: A Computer Code for Thermal-Mechanical Nuclear Fuel Analysis under Steady-state and Transients

Fuel Analysis under Steady-state and Transients (FAST) is the U.S. Nuclear Regulatory Commission (NRC)’s computer code that calculates the steady-state and transient response of nuclear reactor fuel rods during long-term in-reactor burnup, anticipated operational occurrences (AOOs), design basis accidents (DBAs), and dry storage conditions. The code calculates the temperature, pressure, and deformation of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by the code include heat conduction through the fuel and other materials, heat transfer from the cladding-to-coolant, cladding elastic and plastic deformation (including creep), fuel-cladding mechanical interaction, fission gas release from the fuel, rod internal pressure, void volume, and cladding oxidation. The code contains necessary material and coolant properties, as well as clad-to-coolant heat transfer correlations, for normal operation through postulated accidents and AOOs for today’s U.S.-based light water reactor (LWR) fuel designs. FAST-1.2.2 also contains preliminary materials and models for new LWR fuel concepts, such as accident tolerant fuel (ATF), and non-LWR fuel concepts such as metallic fuels for sodium fast reactors (SFRs). FAST has been developed for use on Windows and Linux operating systems. This document describes FAST-1.2.2 and is one of a series of documents on the code; the other documents detail the material properties used by FAST as well as its integral assessment to experiments and commercial data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

DISSOLUTION OF SURROGATE U-Zr FUEL USING ALNIFLEX CONDITIONS

Non-aluminum clad spent nuclear fuel (NASNF) stored in L Basin at the Savannah River Site (SRS) is widely varied in fuel composition, design, packaging, and physical condition. The complexity of the NASNF inventory presents significant challenges, and technology development is necessary for successful disposition. One such fuel in the inventory is metallic uranium-zirconium (U-Zr) alloy fuel, the focus of this study. Electrolytic or nitric acid only dissolution of metallic U-Zr alloy can form insoluble zirconium oxide, which results in up to 52% loss of U to insoluble solids, and can be subject to potentially uncontrolled oxidation reactions [1, 2]. The AlNiflex process was determined to be a viable dissolution flowsheet for the U-Zr alloy fuel. Under a narrow set of solution concentrations, a combination of hydrofluoric acid (HF), nitric acid (HNO3), aluminum nitrate (Al(NO3)3), and hexavalent chromium can safely dissolve U-Zr intermetallic alloys, keep Zr soluble, and not significantly corrode stainless steel (SS) vessels [3, 4.

Gogolski, Jarrod M. [Savannah River National Labor↗
DOE OSTI2024

Cr-coated Accident Tolerant Fuel Concept Source Term Accident Sequence Analysis - High Burnup Fuel Source Term Accident Sequence Analysis Supplement

To extend NUREG-1465 and high burnup fuel source term (SAND2023-01313) recommendations, representative radiological releases to containment – patterned after NUREG-1465 – have been evaluated for LWRs utilizing the chromium-coating on major zircaloy structures (cladding and fuel canisters) and high burnup fuel with enrichments of 8% and 10% for PWRs and BWRs, respectively. Representative radionuclide releases are generated for this accident tolerant fuel concept by applying non-parametric bootstrap methods to MELCOR simulation results. Accident scenarios considered in this analysis include principle contributors to historical core damage frequency estimates for a range of nuclear reactor technologies representative of the operating U.S.A. fleet of nuclear reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1971

Calculation of radiation induced swelling of uranium mononitride using the digital computer program CYGRO 2

Fuel volume swelling and clad diametral creep strains were calculated for five fuel pins, clad with either T-111 (Ta-8W-2.4Hf) or PWC-11 (Nb-1Zr-0.1C). The fuel pins were irradiated to burnups between 2.7 and 4.6%. Clad temperatures were between 1750 and 2400 F (1228 and 1589 K). The maximum percentage difference between calculated and experimentally measured values of volumetric fuel swelling is 60%.

Davison, H. W.↗
DOE OSTI2024

Iron-Chromium-Aluminum Accident Tolerant Fuel Concept Source Term Accident Sequence Analysis - High Burnup Fuel Source Term Accident Sequence Analysis Supplement

To extend NUREG-1465 and high burnup fuel source term (SAND2023-01313) recommendations, representative radiological releases to containment – patterned after NUREG-1465 – have been evaluated for LWRs utilizing iron-chromium-aluminum (FeCrAl) alloys in place of zirconium-based alloys in major core structures (cladding and fuel canisters) and high burnup fuel with enrichments of 8% and 10% for PWRs and BWRs, respectively. Representative radionuclide releases are generated for this accident tolerant fuel concept by applying non-parametric bootstrap methods to MELCOR simulation results. Accident scenarios considered in this analysis include principle contributors to historical core damage frequency estimates for a range of nuclear reactor technologies representative of the operating U.S.A. fleet of nuclear reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Recent Metallic Fuel Data Recovery in FIPD

The Metallic Fuels Irradiation and Physics Database (FIPD) [1] is an organized collection of metallic fuel test pin data (U-xPu-yZr, = 0 ~ 28; y = 2 ~ 10) and documentation available to industry. FIPD mainly contains three types of data: (1) Fuel pin fabrication data, including fuel slug diameter, fuel slug length, cladding diameter, smear density, etc. (2) Fuel pin operation conditions, including axial distributions for power, temperatures, fluences, burnup, and isotopic densities, etc. and (3) Fuel pin post-irradiation examination (PIE) data, including fission gas release and gas chemistry, profilometry, and neutron radiography, etc. The operating conditions for pins with PIE data available in FIPD span significant ranges across key parameters. The fuel peak burnup extends from less than 5% up to 20 at%. The cladding peak temperature varies from about 490°C to 660°C. Finally, the cladding peak DPA shows a wide range from less than 5 to 120. These broad ranges reflect the diverse testing conditions and operational parameters captured in the available PIE data. More detail about FIPD can be found in ref. [2]. The database development is an ongoing effort covering metallic fuel experiments from the Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF). As reported in the ref. [3, 4], most of the PIE data generated during the IFR program [5] has been collected, reviewed, processed, and integrated into FIPD. The most recently added PIE data can be found in ref. [4], which shows the collection of over 95% of the PIE data by the time of this paper. The recent improvements to the database are summarized in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗