SEARCH · Search NASA

Results for “Glass transition temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Cleavable Strand‐Fusing Cross‐Linkers as Additives for Chemically Deconstructable Thermosets with Preserved Thermomechanical Properties

Abstract Permanently cross‐linked polymer networks—thermosets—are often difficult to chemically deconstruct. The installation of cleavable bonds into the strands of thermosets using cleavable comonomers as additives can facilitate thermoset deconstruction without replacement of permanent cross‐links, but such monomers can lead to reduced thermomechanical properties and require high loadings to function effectively, motivating the design of new and optimal cleavable additives. Here, we introduce “strand‐fusing cross‐linkers” (SFCs), which fuse two network strands via a four‐way cleavable cross‐link. SFCs enable deconstruction of model polydicyclopentadiene (pDCPD) thermosets with as little as one‐fifth of the molar loading needed to achieve deconstruction using traditional cleavable comonomers. SFCs function under traditional oven curing as well as low‐energy frontal ring‐opening metathesis polymerization (FROMP) conditions and lead to improved thermomechanical properties, for example, glass transition temperatures, compared to prior cleavable comonomer designs. This work motivates the development of increasingly improved cleavable additives to enable thermoset deconstruction without compromising material performance.

Zhang, Shuyi [Department of Chemistry Massachusett↗

DOE OSTI2025

Polysulfamates as “Macroisosteres” of Polyurethanes with Improved Degradability

Abstract Addressing the environmental persistence of plastics requires the development of next‐generation polymers that combine high performance with enhanced degradability. Progress toward this grand challenge has been impeded, in part, by the absence of a general blueprint for the macromolecular design of such materials. Herein, we introduce a “macroisostere” design strategy, where the carbonyl group (–CO–) in polyurethanes (PUs) is replaced with a sulfonyl group (–SO 2 –), resulting in a virtually unknown family of polymers called polysulfamates. This approach, inspired by the use of bioisosteres in drug discovery, aims to preserve key interchain interactions that contribute to thermomechanical performance while enhancing the hydrolytic lability of the polymer backbone. The optimization of a Sulfur(VI) Fluoride Exchange (SuFEx) polymerization allowed the synthesis of ten polysulfamates structurally analogous to common PUs. Comparative analysis of one PU and its polysulfamate analog showed that this isosteric substitution increases thermal stability, slightly lowers the glass transition temperature, and retains similar hardness and reduced Young's modulus. Notably, the S(VI)‐based polysulfamate demonstrated significantly enhanced hydrolytic degradability. These results highlight the potential of the “macroisostere” approach as a generalizable strategy for designing high‐performance, degradable alternatives to traditional plastics.

Chemistry↗

DOE OSTI2025

Simultaneous Degradation‐Depolymerization of Bioderived Comb Copolymers

Poly(lactic acid) (PLA) is the most widely explored biodegradable alternative for polystyrene; however, its low toughness and glass transition temperature may limit its wider adoption as a sustainable replacement. To improve its material and thermal properties, PLA can be chemically or physically combined with other polymers, like poly(methyl methacrylate) (PMMA), though the incorporation of vinyl‐based polymer components complicates chemical recycling and reduces the sustainability of the material. Here, in this study, we synthesized polymethacrylate‐PLA comb copolymers designed to be thermally deconstructed. Our design strategically extends current polymer deconstruction methodologies to more complex macromolecular systems. Thermally labile units within the polymethacrylate backbone permitted depolymerization that was concurrent with PLA side chain degradation during heating. This dual degradation‐depolymerization process enhances the overall sustainability of lactide/vinyl‐based copolymers and demonstrates the synergistic potential of integrating multiple deconstruction pathways into a single system. This report elaborates on the design of advanced, degradable copolymers, contributing to the further development of sustainable polymer materials.

PLA↗

DOE OSTI2026

Supramolecular Arene‐Perfluoroarene Assembly Enhances Photoiniferter Polymerization Kinetics

Ultra-high-molecular-weight (UHMW, >106 Da) polymers have unique thermomechanical properties due to their large number of physical entanglements. Producing UHMW styrenic polymers is challenging because of their prohibitively slow homopolymerization kinetics. In this report, we show that alternating photoiniferter copolymerization between methoxy-functionalized styrenic monomers and pentafluorostyrene can circumvent this limitation under conditions where arene–perfluoroarene (AP) interactions contribute to favorable monomer association and accelerate copolymerization. Increasing methoxy substitution on the styrene arene ring leads to pronounced rate enhancements that correlate with electronic complementarity between the styrenic comonomers. Density functional theory calculations reveal increasingly favorable AP interaction energies across the series, consistent with monomer association contributing to faster propagation. The result is up to 2000% enhancement in propagation rate in copolymerizations compared to styrene homopolymerization. Despite these rate enhancements, the resulting materials retain broadly similar glass-transition temperatures and network-like thermomechanical behavior, with only modest softening across the series. Here, we then leverage the approach to produce UHMW trialkoxystyrene copolymers bearing sterically encumbered pendants, which are ultrasoft (Young's modulus of 8 kPa) and highly extensible (560%). These results establish that designed supramolecular association between styrenics is a powerful tool for controlling reactivity in radical polymerization and generating otherwise difficult-to-obtain materials.

Marquez, Joshua D. [University of Florida, Gainesv↗

DOE OSTI2022

Bio‐based glycerol plasticizers for flexible poly(vinyl chloride) blends

Abstract A series of glycerol‐based compounds were investigated for their application as plasticizers for flexible poly(vinyl chloride) (PVC) blends. The effect of plasticizer chemical structure on the performance, migration behavior, and blend morphology were evaluated and compared to blends produced using the commercial plasticizer dioctyl terephthalate (DOTP). Blends containing 40 phr (parts per hundred rubber) of glycerol‐based plasticizer showed a considerable reduction (between 54 to 86°C) in glass transition temperature ( T g ) relative to neat PVC ( T g ~ 80°C). Tensile testing of samples prepared with the glycerol analogs demonstrated higher ductility (elongation at break values of up to 97%) than DOTP (elongation at break value of 75%) at identical plasticizer loadings. The surface morphologies showed excellent incorporation of the glycerol plasticizers functionalized with alkyl chains longer than four carbons in length into the PVC matrix, whereas droplet formation was observed in blends with shorter chain glycerol derivatives. Leaching behavior of the plasticized samples were evaluated into different media and showed that plasticizers comprised of branched, or longer alkyl chains produced 2‐ to 4‐fold lower migration rates compared to those with shorter alkyl chains into polar solutions.

Halloran, Matthew W.↗

DOE OSTI2022

Development of high‐performance partially biobased thermoset polyester using renewable building blocks from isosorbide, 1,3‐propanediol, and fumaric acid

Abstract Research on biobased thermoset resins has been overlooked when compared with the rapid progress on biobased thermoplastics. The objective of this work was to develop unsaturated polyester prepolymers based on building blocks derived from renewable raw materials, namely, biobased isosorbide, 1,3‐propanediol, and fumaric acid, with petroleum‐derived phthalic anhydride. The prepolymers developed herein behaved as low‐molecular weight macromolecules (oligoesters), with M n varying between 1.2 and 1.5 kDa, but achieved a high bio‐content of up to 87.1 wt%. The prepolymers were incorporated into reactive diluents comprising a blend of 2‐hydroxyethyl methacrylate and styrene, formulated to be eco‐friendlier and less toxic than typical styrene‐only incorporation approach, thus resulting in resins with viscosities between 750 and 950 cP. These resins are suitable for use in various fiber‐reinforced polymer production techniques, such as manual lamination, vacuum infusion, and pultrusion, having the benefit of presenting over 50 wt% of bio‐content in some formulations. Moreover, the crosslinked polyester resins (thermosets) exhibit comparable mechanical and thermomechanical behavior to their petrochemical‐based counterparts, with modulus of elasticity and tensile strength of up to 3.9 GPa and 62.1 MPa, respectively, and glass transition temperatures of up to 106°C, making them greener alternatives for high‐performance structural applications.

Hofmann, Mateus↗

DOE OSTI2024

Low‐Temperature and High‐Rate Rechargeable Aluminum Batteries Enabled by Ternary Eutectic Electrolytes

Abstract Rechargeable aluminum batteries (RABs) have garnered extensive scientific attention as a promising alternative chemistry due to the inherent advantages associated with aluminum (Al) metal anodes, including their high theoretical capacities, cost‐effectiveness, environmental friendliness, and inherent non‐flammable properties. Nonetheless, the practical energy density of RABs is constrained by the electrolytes that support lower operational voltage windows. Herein, we report a ternary eutectic electrolyte composed of 1‐ethyl‐3‐methylimidazolium chloride ([C 2 C 1 im]Cl):1‐butyl‐3‐methylimidazolium chloride ([C 4 C 1 im]Cl):aluminum chloride (AlCl 3 ) for the application of RABs. The electrolyte exhibits a high operational potential window (~3 V vs. Al/Al 3+ on SS 316) and high ionic conductivity (~8.3 mS cm −1 ) while exhibiting only a low temperature glass transition at −65 °C suitable for all‐climate conditions. Al||graphene nanoplatelets cell delivers a high capacity of ~117 mAh/g, and ~43 mAh/g at a very high current densities of 1 A/g and 5 A/g, respectively. The cells render a reversible capacity of 20 mAh/g at −20 °C and 17 mAh/g at −40 °C, indicating their suitability for operation under extreme environmental conditions. We comprehensively evaluated the design and optimization of carbon paper‐based battery systems. The ternary eutectic electrolyte demonstrates exceptional electrochemical performance, thus signifying its substantial potential for utilization in high‐performance energy storage systems in all climates.

Vadthya, Raju↗

DOE OSTI2022

A Study on Recycled Polymers Recovered from Multilayer Plastic Packaging Films by Solvent–Targeted Recovery and Precipitation (STRAP)

Multilayer plastic film use increased in multiple packaging applications due to its versatility and overall increased performance over monolayer structures. However, the performance gains from multiple layers also make recycling difficult because they contain multiple polymers that can be immiscible and burdensome to traditional mechanical recycling operations. A possible solution is the solvent-targeted recovery and precipitation (STRAP) process, but the effect on the retrieved polymer is still unknown. Here, the STRAP process is applied to two different multilayer films and samples of recovered polymers are evaluated for physical, molecular, and thermal properties. Changes in the molecular weight are not significant, but differences in thermal properties are reported along with the coprecipitation of different polymers. Solvent retention in the polymer matrix from STRAP reduced the glass transition temperature of samples, but enhanced drying recovered it. Heavy metals, such as Cd, Cr, and Pb are not detected, indicating regulatory compliance for different applications.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Material property characterization of 3D printed polypropylene wood plastic composites

Abstract Wood flour (WF) at 10 wt.% and 20 wt.% loadings was used as a reinforcing filler to enhance the applicability of polypropylene (PP) for 3D printing. After performing printability tests of PP wood plastic composites (WPCs), the mechanical properties of both injection‐molded and 3D‐printed PP WPC specimens were explored. Test specimens were prepared from 3D printed hexagons for analyzing the mechanical properties. Adding WF to neat PP increased the storage modulus and the glass transition temperature while decreasing the degree of crystallinity and the coefficient of thermal expansion, while enhancing the printability of neat PP. The tensile strength, tensile modulus of elasticity, flexural strength, and flexural modulus of elasticity of injection‐molded neat PP improved by up to 21%, 59%, 30%, and 56%, respectively, with 20 wt.% WF. However, the impact strength of injection‐molded neat PP decreased by 85%, with 20 wt.% WF. After 3D printing, the tensile strength and tensile modulus of elasticity of printed neat PP increased by up to 84% and 60%, respectively, with 20 wt.% WF. The flexural strength and flexural modulus of elasticity of neat printed PP remained unchanged compared to those of PP filled with 20 wt.% WF, while the impact strength decreased by 87%. Highlights WF was used as a reinforcement in polypropylene designed for 3D printing A pilot‐scale, pellet‐fed 3D printer was used to print hollow hexagons, and then test specimens were fabricated from these hexagons for mechanical properties The tensile and flexural properties of 3D printed neat polypropylene improved, while the impact strength decreased after adding 20 wt.% WF to the neat PP.

Hwang, Sungjun↗

DOE OSTI2024

Synthesis and characterization of biobased copolyesters based on pentanediol: (1) Poly(pentylene dodecanoate–co–furandicarboxylate)

A series of biobased aliphatic-aromatic copolyesters, poly(pentylene dodecanoate-co-furandicarboxylates) (PPeDFs) were synthesized via an esterification and polycondensation melt process. The copolyesters were characterized using gel permeation chromatography, Fourier transform infrared spectroscopy, 1 H NMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis, wide angle x-ray scattering, and tensile testing. The thermal transition behavior was strongly dependent on composition, with the melting and glass transition temperatures reaching a minimum at approximately equimolar ratio of D to F. All copolyesters were stable below 300°C with their R 600 (the weight of material remaining at 600°C) values increasing with F fraction. PPeD to PPeDF30 (e.g., mole ratio D/F = 7:3) show sharp PPeD crystalline reflections only while broad PPeF reflections are shown in PPeF and PPeDF90. PPeDF40 to PPeDF80 showed both crystal structures. The fractional crystallinity for the PPeD was much higher than PPeF and the fractional crystallinity of the copolymers showed a minimum at D/F ratios closer to the latter. Here, the stress at break and modulus both exhibited maxima at D/F ratios that were either high or low, but somewhat surprisingly a strong maximum in percent elongation at break of over 600% occurs at PPeDF40. For this composition, a typical plastic behavior curve was found including a yield point, high elongation at break, and strain hardening.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Role of tunable polymer flexibility in controlling wetting behavior and thermal properties of poly(1,3-cyclohexadiene)-silica nanocomposites

We present how altering the chain flexibility affects the nanoscale organization of polymer-grafted nanoparticles (PGNPs) and its ultimate impact on macroscale thermal properties. To isolate the role of chain flexibility on wetting behavior in athermal polymer nanocomposites (PNC), the graft and matrix chemistry is kept identical by utilizing 1,3-cyclohexadiene-based polymer materials. Increasing the rigidity and molecular weight of both the graft and matrix is found to favor mixing of poly(1,3-cyclohexadiene) PCHD-grafted silica NPs with the matrix, supported by a concomitant increase in glass transition temperatures of the PNCs. Further, the associated entropic factors that drive wetting behavior and dispersion of PGNPs are discussed, emphasizing the dominant role-played by chain flexibility. Alterations in graft flexibility had the strongest impact on dispersion and Tg values of the PNC, while molecular weight (MW) plays a secondary role. This investigation is a unique demonstration of how chain flexibility alteration in athermal semiflexible systems can be used to alter NP organization by altering filler-matrix wettability which also impacts thermal properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

The effect of polymer grafting on the mechanical properties of PEG-grafted cellulose nanocrystals in poly(lactic acid)

Poly(lactic acid) (PLA) is a commercially available bio-based polymer that is a potential alternative to many commodity petrochemical-based polymers. However, PLA's thermomechanical properties limit its use in many applications. Incorporating polymer-grafted cellulose nanocrystals (CNCs) is one potential route to improving these mechanical properties. One key challenge in using these polymer-grafted nanoparticles is to understand which variables associated with polymer grafting are most important for improving composite properties. In this work, poly(ethylene glycol)-grafted CNCs are used to study the effects of polymer grafting density and molecular weight on the properties of PLA composites. All CNC nanofillers are found to reinforce PLA above the glass transition temperature, but non-grafted CNCs and CNCs grafted with short PEG chains (<2 kg mol –1 ) are found to cause significant embrittlement, generally resulting in less than 3% elongation-at-break. By grafting higher molecular weight PEG (10 kg mol –1 ) onto the CNCs at a grafting density where the polymer chains are predicted to be in the semi-dilute polymer brush conformation (~0.1 chains nm –2 ), embrittlement can be avoided.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Initiator‐Driven Tailoring of Reactivity and Inhibition in Frontally Polymerized Dicyclopentadiene‐Co‐Dihydrofuran Thermosets

Incorporating 2,3‐dihydrofuran (DHF) into dicyclopentadiene (DCPD) enables frontally polymerizable, deconstructible thermosets via acid hydrolysis. At 5–20 mol% DHF and low initiator concentration (~100 ppm), DHF inhibits front propagation, lowers the glass transition temperature ( T g ) by up to 20°C, and quenches the front, especially at 20% DHF. This paper demonstrates that increasing the initiator concentration to 250–1000 ppm overcomes inhibition, enhances front speeds by ~50%, and suppresses quenching at the expense of pot‐life. Above 5 mol% DHF, an emergence of a second exotherm is observed, attributed to increased rate dependence on the inhibition of the initiator by DHF. Void formation from volatile DHF is suppressed by applying 110 kPa nitrogen, though at the cost of reduced front speed. Dynamic mechanical analysis shows that higher initiator concentration produced more highly cross‐linked polymers, with a ~20% increase in storage modulus at 25°C and a 20°C increase in T g .

deconstructible thermosets↗

DOE OSTI2026

From bulk to surface: Structure and dynamics of amorphous alumina from deep potential molecular dynamics

Understanding the atomic-scale structure and dynamics of amorphous oxide surfaces is essential for interpreting their chemical reactivity, mechanical stability, and interfacial behavior, yet direct experimental characterization remains challenging. We employ Deep Potential (DP) molecular dynamics to generate large-scale, ab initio -quality models of amorphous Al 2 O 3 bulk glasses and melt-quenched free surfaces, enabling a quantitative analysis of both structure and relaxation dynamics with statistical confidence inaccessible to direct ab initio simulation. The trained DP model reproduces experimental liquid and glass structure, captures the cooling-rate dependence of the bulk glass transition, and corrects systematic biases in the polyhedral populations predicted by widely used classical force fields. At the free surface, mass density recovers to bulk values over ~10 Å, while local coordination requires a slightly wider subsurface region to fully converge. The outermost layer is oxygen-enriched, exhibits altered polyhedral connectivity with contracted Al–O bonds, and hosts a broad population of under-coordinated motifs (notably AlO 3 and OAl 2 ) whose abundances are governed by glass stability. These under-coordinated surface motifs exhibit distinct vibrational signatures and occur as locally paired Lewis acid and Brønsted base sites consistent with bond-valence compensation, yet remain spatially dispersed rather than aggregating into extended clusters. Despite this pronounced structural heterogeneity, surface relaxation and the glass-transition temperature remain comparable to their bulk counterparts, suggesting that the disordered surface is kinetically stable once formed. Together, these results establish a molecular-level picture of amorphous alumina surfaces and demonstrate the capability of machine-learned potentials to resolve structure–property relationships in disordered oxide interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Compositional effects on cure kinetics, mechanical properties and printability of dual-cure epoxy/acrylate resins for DIW additive manufacturing

Interest in 3D printing of thermoset resins has increased significantly in recent years. One approach to additive manufacturing of thermoset resins is printing dual-cure resins with direct ink write (DIW). Dual-cure resins are multi-component resins which employ an in situ curable constituent to enable net-shape fabrication while a second constituent and cure mechanism contribute to the final mechanical properties of the printed materials. In this work, the cure kinetics, green strength, printability, and print fidelity of dual-cure epoxy/acrylate thermoset resins are investigated. Resin properties are evaluated as a function of acrylate concentration and in situ UV exposure conditions. The acrylate cure kinetics are probed using photo-differential scanning calorimetry and the impacts of resin composition and UV cure profile on the acrylate extent of conversion are presented. Continuous and pulsed UV cure profiles are shown to affect total conversion due to variances in radical efficiency at different UV intensities and acrylate concentrations. The effects of acrylate concentration on the kinetics of the epoxy thermal cure and the final mechanical properties are also investigated using dynamic mechanical analysis and three-point bend measurements. The glass transition temperature is dependent on formulation, with increasing acrylate content decreasing the T g . However, the room temperature shear moduli, flexural moduli, strength, strain-to-failure, and toughness values are relatively independent of resin composition. The similarity of the final properties allows for greater flexibility in resin formulation and in situ cure parameters, which can enable the printing of complex parts that require high green strength. We found that the in situ UV print intensities and exposure profiles that are necessary to achieve the best print quality are not, in most cases, the conditions that maximize conversion of the acrylate network. Lastly, this highlights the importance of developing optimized resin compositions which enable complete cure of the acrylate network by promoting acrylate dark cure or thermal cure.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Volatile organic compound emissions from 4D printing: Effects of material composition and external stimulus

4D printing of stimuli-responsive materials extends 3D printing by enabling the fabricated structures to transform their shapes and properties over time in response to external stimuli. Numerous research efforts have been dedicated to developing new smart materials, enhancing material printability, and ensuring time-evolving properties. Meanwhile, the use of smart materials and external stimuli in 4D printing has introduced the possibility of air emissions that can potentially deteriorate the indoor air quality at the workplace and pose continuous health hazards to users during the production and use phases. These potential air emissions caused by 4D printing have not yet been assessed in current literature, leading to unknown occupational hazards and human health effects. This study focuses on stereolithography-based 4D printing with constrained thermo-mechanics and builds an emission model to quantify the volatile organic compound emissions from printing, shape programming, and shape recovery stages. The established model mathematically links the emission characteristics with material compositional design and stimuli-response mechanisms. Additionally, shape fixity and recovery abilities are considered to analyze the trade-off between the air emissions and stimuli-response performance of 4D printed parts. Case study results suggest that the methacrylate-based thermo-responsive material with higher glass transition temperature leads to higher air emissions, surpassing the permissible exposure level in the indoor environment. By altering the thermo-temporal conditions, a 61.29% reduction in emission yield can be achieved while ensuring a satisfactory shape memory performance.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Bona fide upcycling strategy of anhydride cured epoxy and reutilization of decomposed dual monomers into multipurpose applications

Waste epoxy materials become an enormous problem to society and the environment. The advantages of epoxy resins derive from their rigid and chemically stable networks, but these qualities also make them difficult to dispose of or recycle. In this work, we demonstrated an efficient degradation of anhydride cured epoxy resin by aminolysis in aminoethanol without using any catalysts. The epoxy resin was fully decomposed at 160 °C in 4 h, resulting in two distinct high purity monomers (HHPA-OH and BPA-OH). To fully realize this upcycling approach, The BPA-OH was used to synthesize a polyurethane coating with an excellent glass transition temperature (88.9 °C), scratch hardness (8H), gouge hardness (6H), adhesive strength (5B), and strong solvent resistance. The HHPA-OH with two hydroxyl groups was reacted with methacrylic anhydride to form a dimethacrylate monomer which was then used as a viable crosslinker for photo-curable 3D printing thermosetting polymer with tensile strength as high as 64 MPa and impact strength of 4.86 kJ/m 2 . This work demonstrates a feasible pathway to convert anhydride cured epoxy waste to new monomeric recyclates for superior polymer products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Effects of cleavable comonomer structure and crosslinker chemistry on the performance and deconstructability of frontally cured pDCPD composites

Reclaiming undamaged carbon fiber from thermoset composites requires chemical recycling methods that leverage complete deconstruction of the polymer matrix. Cleavable comonomers enable chemical recycling of poly(dicyclopentadiene) (pDCPD) composites, but current systems suffer from reduced glass transition temperature (T g ), limiting application. Here, we investigate the effect of cleavable comonomer loading and cleavable crosslinker chemistry on network formation, thermomechanical properties, and fiber recovery in frontally cured pDCPD composites. All formulations fully deconstructed in acid and recovered fibers ranged from pristine to variably contaminated depending on crosslinker chemistry. Reducing backbone-cleaving comonomer content and introducing cleavable crosslinkers raised composite T g to 126–138 °C compared to 105 °C previously reported in deconstructable pDCPD composites. Although the cleavable crosslinkers increased T g in unreinforced polymers to 150–160 °C, the fiber-reinforced composite T g remained lower due to under-curing and interactions between the crosslinkers and the fiber surface. Increasing polymerization initiator loading improved comonomer conversion and yielded a deconstructable composite with T g = 151 °C, approaching the performance of non-deconstructable pDCPD composites (T g = 161 °C). This work clarifies how cleavable comonomer and crosslinker chemistry governs curing, thermomechanical performance, and reclaimed reinforcement quality, and the results highlight the need for more robust cleavable comonomers to realize multigenerational composite materials without sacrificing thermomechanical performance.

Carbon fibers↗