Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

In-depth quantitative analysis of the microstructures produced by Surface Mechanical Attrition Treatment (SMAT)

Electron BackScattered Diffraction (EBSD) maps are used to characterize quantitatively the graded microstructure formed by Surface Mechanical Attrition Treatment (SMAT) and applied here to the 316L stainless steel. In particular, the analysis of GNDs – coupled with relevant and reliable criteria – was used to depict the thickness of each zone identified in the SMAT-affected layers: (i) the “ultrafine grain” (UFG) zone present at the extreme top surface, (ii), the “transition zone” where grains were fragmented under the heavy plastic deformation and, finally, (iii) the “deformed zone” where initial grains are simply deformed. The interest of this procedure is illustrated through the comparative analysis of the effect of some SMAT processing parameters (amplitude of vibration and treatment duration). The UFG and transition zones are more significantly modified than the overall affected thickness under our tested conditions. - Highlights: • EBSD maps are used to characterize quantitatively the microstructure of SMAT treated samples. • Calculation of the GND density to quantify strain gradients • A new method to depict the different zone thicknesses in the SMAT affected layer • Effects of SMAT processing parameters on the surface microstructure evolution.

36 MATERIALS SCIENCE↗

Co-, Ni- and Fe-rich grain-boundary phases enhance creep resistance in θ'-strengthened Al-Cu alloys

Here, microstructural evolution and creep response were investigated in the cast Al-5.0Cu-0.3Mn-0.2Zr (wt.%) alloy with and without addition of slow-diffusing, intermetallic-forming elements Fe, Ni, or Co. Baseline Al-5.0Cu-0.3Mn-0.2Zr alloy exhibits high creep resistance at 300 °C, up to ~75 MPa, which is attributed to high-aspect-ratio, intragranular θ'-Al 2 Cu precipitates that effectively suppress dislocation climb. However, θ'-Al 2 Cu precipitate-free zones form along grain boundaries upon heat treatment, whose extent is amplified during subsequent creep. Such weak regions experience dislocation creep, leading to strain localization and acceleration of grain-boundary sliding. Adding Ni and Co, individually or in combination, leads to the formation of grain-boundary precipitates (Al 9 Co 2 , Al 3 Ni 2 ) which are resistant to coarsening, thus suppressing the formation of θ'-Al 2 Cu precipitate-free zones. This microstructure provides high creep resistance at stresses up to 75–80 MPa, with strain rates much lower than in unmodified Al-5.0Cu-0.3Mn-0.2Zr. Adding Fe, which results in extensive decoration of grain boundaries with coarsening-resistant Al 7 Cu 2 Fe, and then increasing the Cu content to compensate for the Cu loss to this new phase, leads to a new Al-7.4Cu-1.6Fe-0.3Mn-0.2Zr alloy with creep resistance at 300 °C that surpasses known cast aluminum alloys. Adding Fe to improve the creep resistance of Al-Cu alloys is both cost-effective and sustainable. Our findings offer guidelines applicable to various alloy systems on controlling the evolution of precipitate-free zones and its ensuing effects on creep deformation.

36 MATERIALS SCIENCE↗

Additive Manufactured Composite Phase-Change Material for Thermal Energy Storage Applications

Phase-change materials play a critical role in industrial energy storage applications to drive efficiency improvements, thermal energy management, and carbon emissions reductions. Recently, it has been shown that rapid solidification of alloys with metastable immiscibility in the liquid phase has the potential to form unique microstructures in which a low-melting phase is uniformly distributed in a high-melting matrix. This feature can be exploited using additive manufacturing to produce components with complex geometries containing such unique phase-change microstructures. Phase-field simulations utilizing high-performance computing were used to provide a detailed description of the evolution of the active phase during service in terms of their morphology and composition in different polycrystalline matrix grain morphologies that are typically produced during additive manufacturing. Phase field simulations were performed using, MEUMAPPS-SL (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid Liquid) code that was developed in-house by the Oak Ridge National Laboratory. The simulations utilized the capabilities of the Kestrel supercomputer at the National Renewable Energy Laboratory. The simulation results were compared with experimental results generated at Siemens Energy, Inc. The results indicate that the kinetics of liquid spreading along grain boundaries is largely determined by the mobility of the triple line along the intersection of the grain boundary liquid and the grain boundary plane.

25 ENERGY STORAGE↗

Process-driven roadmap for depositing super duplex stainless steel via wire Arc additive manufacturing

Here, this study systematically investigates the effects of shielding gas, bead spacing, weld mode, and travel speed on the phase balance, porosity, and hardness of wire arc additively manufactured (WAAM) super duplex stainless steel (ER2594). Robotic WAAM was employed to fabricate multilayer walls under systematically varied process conditions, followed by phase transformation simulations, X-ray computed tomography (XCT), electron backscatter diffraction (EBSD), and microhardness evaluation. Thermodynamic simulations predicted rapid cooling of AM process can suppress the potential formation of deleterious precipitates which was later validated via cross-sectional microstructure analyses of printed samples. XCT revealed porosity levels below 0.2% for all deposits, with reduced travel speed significantly lowering defect volume. Microstructural analyses revealed the evolution of various austenite precipitates, including grain boundary austenite (GBA), Widmanstätten austenite (WA), and intergranular austenite (IGA), sequentially upon cooling of the ferrite phase. Among all process parameters, weld transfer mode exhibited the strongest influence on phase balance; pulsed mode promoted higher ferrite retention (~ 36%) compared to RapidX mode. No consistent relationship between stabilized phase fraction and captured microhardness was observed. This work provides critical insights for optimizing WAAM parameters to control phase balance and mechanical performance, which is essential for producing high-integrity super duplex stainless-steel components for nuclear and marine applications.

Grain orientation↗

Microstructure Evolution and Mechanical Properties of Large-Scale AZ80 Magnesium Alloy Billets Produced by Multitemperature Multidirectional Forging

Grain refinement is an effective method to improve the mechanical properties of magnesium (Mg) alloys. In the present research, the combination of multidirectional forging (MDF) and forward extrusion for sizing with decreasing temperature pass by pass was employed to deform as-cast AZ80 magnesium alloy billet with large size to obtain fine grains and homogeneous microstructure. It was found that with the increasing number of MDF passes, the average grain size decreases; the homogeneity of microstructures and the percentages of dynamic recrystallised grains increase simultaneously. After six-pass MDF, fine and homogeneous microstructure with an average grain size of 15 μm was achieved; however, grain refinement became very difficult with a further increase in the MDF pass number. After eight-pass MDF plus forward extrusion for sizing, excellent mechanical properties of large-scale AZ80 magnesium alloy billet were obtained. The tensile strength, the yield strength and the elongation of billet are 410 MPa, 292 MPa and 14%, respectively. Furthermore, during multitemperature MDF, the inverse of the square root of grain size and tensile yield strength fit well with the Hall–Petch relationship.

36 MATERIALS SCIENCE↗

Evolution of grain boundary character distributions in alloy 825 tubes during high temperature annealing: Is grain boundary engineering achieved through recrystallization or grain growth?

Grain boundary engineering (GBE) of nickel-based alloy 825 tubes was carried out with different cold drawing deformations by using a draw-bench on a factory production line and subsequent annealing at various temperatures. The microstructure evolution of alloy 825 during thermal-mechanical processing (TMP) was characterized by means of the electron backscatter diffraction (EBSD) technique to study the TMP effects on the grain boundary network and the evolution of grain boundary character distributions during high temperature annealing. The results showed that the proportion of ∑ 3{sup n} coincidence site lattice (CSL) boundaries of alloy 825 tubes could be increased to > 75% by the TMP of 5% cold drawing and subsequent annealing at 1050 °C for 10 min. The microstructures of the partially recrystallized samples and the fully recrystallized samples suggested that the proportion of low ∑ CSL grain boundaries depended on the annealing time. The frequency of low ∑ CSL grain boundaries increases rapidly with increasing annealing time associating with the formation of large-size highly-twinned grains-cluster microstructure during recrystallization. However, upon further increasing annealing time, the frequency of low ∑ CSL grain boundaries decreased markedly during grain growth. So it is concluded that grain boundary engineering is achieved through recrystallization rather than grain growth. - Highlights: •The grain boundary engineering (GBE) is applicable to 825 tubes. •GBE is achieved through recrystallization rather than grain growth. •The low ∑ CSL grain boundaries in 825 tubes can be increased to > 75%.

36 MATERIALS SCIENCE↗

Coupled phase field damage and crystal plasticity analysis of intragranular fracture: The role of crystallographic orientation and voids

Damage evolution in engineering metal alloys at the grain scale exhibits significant microstructural heterogeneity and anisotropy. These heterogeneities create local hotspots for stress and strain localization, leading to void nucleation. Crystal orientation influences the active slip systems around voids, affecting lattice rotation and potentially forming discontinuities. At low triaxiality, voids may change shape due to lower stress, rotation, elongation, and coalescence. At high triaxiality, the correlation between crystal orientation and void growth rate becomes stronger, resembling the behavior observed in isolated single crystals. Therefore, understanding the effects of crystal orientation, heterogeneous strain, and defect evolution is crucial for single crystal fracture characterization. Here, in this work, a coupled phase-field damage (PFD) and crystal plasticity (CP) model is implemented within a finite element framework to analyze crystal deformation and failure. The CP method employs a dislocation density-based constitutive model, while intragranular failure is modeled using an anisotropic PFD method. The PFD model considers both the stored energy due to elastic stretching and the energy release due to defect formation and crack formation. A single crystal Al2219 with an intracrystalline spherical void is chosen to analyze fracture. The study finds that fracture propagation is strongly correlated with crystal orientations. This coupled CP-PFD model provides accurate failure prediction in crystalline materials by incorporating the effects of crystal orientations and existing voids. This study demonstrates how the local microstructure and defects influence plastic deformation and failure mechanisms in metal alloys.

Aluminum alloy↗

Neutron Diffraction Residual Stress Study of a AA2219-T87 Self-Reacting Friction Stir Weld

2219-T87 is a precipitation hardenable aluminum-copper alloy which sees wide use in structural aerospace components. Thick panels of this alloy are joined via self-reacting friction welding (SRFSW); however, this thermomechanical process can result in significant loss of the alloy’s strengthening precipitates and large residual stresses which are detrimental to mechanical behavior and performance. High-resolution maps of the residual strain and stress states along the normal, transverse, and longitudinal directions of 2219-T87 SRFSW were obtained using neutron diffraction measurements. Residual stress had the highest tensile value in the heat-affected zone (HAZ) and the largest compressive stress in the base metal region of the normal and transverse directions. Line profile residual stress distributions displayed an “M”-shaped distribution in each direction with the longitudinal direction being the most pronounced while 2D residual stresses displayed an hourglass-shaped pattern. Further, average maximal longitudinal residual stress values ranged from 60.6 to 85.6% of yield. Microhardness testing across the transverse weld section produced a “V”-shaped curve with slight hardness recovery in the stir zone. Maximal and minimal microhardness values were observed in the base metal (154 HV) and thermomechanically affected zone (82 HV), respectively. Microstructural evolution was recorded using optical microscopy and showed decreasing grain size from the HAZ to the stir zone.

36 MATERIALS SCIENCE↗

Effect of annealing treatment on the dry sliding wear behavior of copper

We report the effect of annealing on the wear behavior of commercial grade pure copper (Cu) was evaluated by performing unlubricated pin-on-disc wear tests of as-received and annealed samples under 0.1-10 kgf normal load. It was found that annealing at 800 °C for 24 h led to an increase of grain size of Cu from ~ 6.7 to ~ 15.3 μm and a decrease in hardness. Wear rates of both samples increased while the friction coefficients decreased with increasing normal load. Subsurface microstructure evolution and wear debris were characterized by high resolution electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM) after wear tests. Dynamic recrystallization and abnormal subsurface grain growth were observed in both samples under high load. Finally, the effect of annealing on the microstructure evolution and wear resistance of Cu were discussed.

36 MATERIALS SCIENCE↗

Effects of annealing parameters on microstructural evolution of a typical nickel-based superalloy during annealing treatment

Highlights: • Adopting an annealing treatment after deformation can improve the homogeneity of microstructure. • Heterogeneous grains become homogeneous firstly, and then heterogeneous with increasing annealing time. • The optimum annealing parameters are the temperature of 980 °C and the time of 10 min. - Abstract: It is usually one of important goals to obtain the homogeneous microstructure for forgings by hot working, such as hot die forging. However, there is always a large inhomogeneous deformation in die forgings during hot deformation. It often results in an inhomogeneous microstructure of forging due to the different dynamic recrystallization (DRX) fractions and grain sizes in different strain regions. In this study, a method was proposed to improve the homogeneity of deformed microstructure by annealing treatment. The microstructural evolution of a typical nickel-based superalloy during annealing treatment has been investigated. The Optical Microscope (OM), Electron Backscatter Diffraction (EBSD) and Scanning Electron Microscope (SEM) technologies were applied to observe microstructures. It is found that adopting an annealing treatment after deformation can effectively improve the homogeneity of microstructure due to the static recrystallization. There is an incubation period which is not less than 5 min for the occurrence of static recrystallization. The initial heterogeneous grains become homogeneous firstly, and then heterogeneous again when the annealing time is increased from 5 to 30 min. The deformation accelerates the dissolution of delta phase in annealing treatment. The fraction of delta phase decreases at the early stage of annealing whether the temperature exceeds the solution temperature. Based on a comprehensive consideration of all factors, the optimum annealing parameters, which are the temperature of 980 °C and the time of 10 min, have been obtained.

36 MATERIALS SCIENCE↗

Microstructural evolution and phase stability in Nb-containing interstitial Fe-Mn-Co-Cr-C high-entropy alloys: An in-situ synchrotron X-ray diffraction study during laser melting

The influence of Nb on phase stability and microstructural evolution in an interstitial Fe-Mn-Co-Cr-C high-entropy alloy was investigated using in-situ synchrotron X-ray diffraction (SXRD) during laser melting. Scheil-Gulliver simulations predict the formation of σ and γ-f.c.c. phases in all three alloys, along with NbC in Nb-containing compositions. SXRD confirmed the presence of most predicted phases, but the σ phase was absent. Nb promotes crystallite refinement and increases dislocation density, though excessive additions reduce refinement efficiency due to solubility limits and secondary phase formation. Furthermore, Nb addition also enhances ε-h.c.p. phase formation by reducing stacking fault energy through NbC-induced carbon depletion. Analysis of intensity peak evolution reveals that Nb alters preferred grain orientations, reducing {111} γ intensity while enhancing {220} γ , leading to a more isotropic grain distribution. Overall, Nb plays a key role in phase selection, microstructure refinement, and preferred orientation evolution, allowing the tailored microstructure of high-entropy alloys via rapid solidification.

Interstitial high entropy alloys↗

Effect of strain level on the evolution of microstructure in a recently developed AD730 nickel based superalloy during hot forging

Highlights: • Hot forging of AD730 led to formation of large non-recrystallized grains. • Similarity in chemical compositions of the non-recrystallized zones and the matrix. • Increase in strain level promoted recrystallization. - Abstract: Design and control of microstructure of engineering parts made from nickel based superalloys with superior mechanical properties for high temperature applications, require the parts to be subjected to certain thermo-mechanical processing during forging. This often includes sequential straining and annealing at elevated temperatures followed by subsequent aging heat treatments at lower temperatures. In this study, the effect of strain magnitude on the evolution of microstructure during hot forging of a recently developed AD730 nickel based superalloy has been investigated. Microstructural heterogeneity was observed in a forged material manifested in a form of large non-recrystallized grains within the recrystallized matrix that is observed to be dependent on the level of deformation (i.e. strain magnitude). Analyses of microstructure indicated significant reduction in the fraction of low-angle grain boundaries and sub-structures with an increase in the applied strain, suggesting higher fraction of recrystallization with higher levels of strains. It was concluded that the lower strain levels were insufficient to provide enough driving force for complete recrystallization throughout the entire microstructure of the forged material.

36 MATERIALS SCIENCE↗

Microstructural evolution and electrical resistivity of nanocrystalline W thin films grown by sputtering

Highlights: • W thin films with thicknesses of 5–40 nm were deposited by sputtering and annealed up to 400°C. • Grain size of the beta (β)-W was about 5 nm, whereas that of the alpha (α)-W was about 130 nm. • Thickness dependent electrical resistivity variations as a function of annealing temperature were presented. - Abstract: Tungsten (W) thin films and nanostructures, particularly those having a beta (β)-phase, have attracted a large amount of attention lately because an ultrathin β-phase W film attached to a ferromagnetic layer can reverse the direction of magnetization upon current injection. However, in-depth microstructural studies including the phase transformation in W films as a function of thickness and post-deposition heat treatment temperature are rare. Here, we report the microstructural evolution and the change in the electrical resistivity of W films with thicknesses of 5–40 nm. Microstructural analyses indicate that the β-W is nanocrystalline with a small grain size of about 5 nm, while the alpha (α)-W has a grain size larger than 130 nm with random crystal orientation. We present a state diagram showing the phase of the W film as functions of film thickness and annealing temperature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Grain Structure Evolution in Fe-6Si During Directed Energy Deposition

The purpose of this study is to explore the effect of additive manufacturing (AM) process variables on the grain structure of Fe-6Si, a soft-magnetic alloy used in electrical machine and grid applications. Samples were fabricated with laser engineered net shaping (LENS) with varying inter-pass timing and numbers of unidirectional passes. Here the results show that the grain structure was affected by both solidification and solid-state grain growth mechanisms. A model of the LENS process suggests that, although shorter inter-pass times encourage greater nucleation of new grains and therefore grain refinement during solidification, these conditions also help maintain high solid-state temperatures that allow for grain boundary motion to keep pace with the build rate. Grains formed under these conditions may span multiple layers, and the high-temperature gradient promotes directional growth. This new understanding of these microstructure evolution mechanisms will aid in using process conditions to control the competition between solidification and solid-state grain growth to create grain structures that may not be possible with conventional processing.

36 MATERIALS SCIENCE↗

The complex structural and chemical nature of monolithic U-10Mo fuel and Zr barrier layer

Nanoscale microstructural characterization by advanced transmission electron microscopy techniques on a U-10Mo/Zr barrier layer monolithic fuel plate was performed to evaluate the microstructural evaluation after high burn-up. Gas bubble superlattice evolution, grain restructuring, and evolution of the Zr interaction layer is investigated through detailed electron microscopy characterization. The use of automated crystallographic orientation mapping to irradiated U-10Mo fuel highlights that the restructured ultra-fine grains are separated by high angle grain boundaries at a burn up of 4.42 × 10 21 fissions/cm 3 . Additionally, advanced chemical analysis and multi-variable statistical analysis shows spatial clustering of solid fission product precipitates. Finally, characterization of a newly observed porous nanocrystalline Zr region in the barrier layer is studied. Finally, this work provides insights into the grain subdivision and restructuring process while using advanced microscopy techniques to analyze fission products in neutron-irradiated U-10Mo fuel.

36 MATERIALS SCIENCE↗

Biaxial deformation in high purity aluminum

The convergence of multiple characterization tools has been applied to investigate the relationship of microstructure on damage evolution in high purity aluminum. The extremely coarse grain size of the disc-shaped sample provided a quasi-two dimensional structure from which the location of surface-measured features could be inferred. In particular, the role of pre-existing defects on damage growth was accessible due to the presence of casting porosity in the aluminum. Micro tomography, electron backscatter diffraction, and digital image correlation were applied to interrogate the sample in three dimensions. Recently micro-bulge testing apparatus was used to deform the pre-characterized disc of aluminum in biaxial tension, and related analysis techniques were applied to map local strain fields. Subsequent post-mortem characterization of the failed sample was performed to correlate structure to damaged regions. We determined that strain localization and associated damage was most strongly correlated with grain boundary intersections and plastic anisotropy gradients between grains. Pre-existing voids played less of an apparent role than was perhaps initially expected. Finally, these combined techniques provide insight to the mechanism of damage initiation, propagation, and failure, along with a test bed for predictive damage models incorporating anisotropic microstructural effects.

36 MATERIALS SCIENCE↗

Microstructure Evolution and Microhardness Distribution of Copper Processed Using Multiple Passes of Elliptical Cross-Sectional Spiral Equal-Channel Extrusion

The aim of this work is to study the effect of six-pass elliptical cross-sectional spiral equal-channel extrusion (ECSEE) on the microstructure and performance of ultrafine-grained (UFG) copper. Equiaxed grains of average grain size of less than 1 μm are formed into shear bands in the low strain region of ECSEE deformed specimen. More homogeneous and equiaxed microstructure with high misorientation angles is obtained in the high strain. Moreover, the microstructure evolution of ECSEE-induced copper is a dynamic equilibrium process of shear deformation accompanying the interactions of high dislocation density, cellular structure and high-angle grain boundaries. The grain ECSEE refinement mechanism is described as the formation process of dislocations, cells, local grain sub-boundaries rotation and large angle grain restructure. The significantly non-uniform hardness distribution is consistent with the deformation behavior and microstructure refinement in the ECSEE-induced specimen. The homogeneity of microstructure and hardness improves as the ECSEE pass increases.

36 MATERIALS SCIENCE↗

Evolution of mechanical properties of ultrafine grained 1050 alloy annealing with electric current

The tensile properties and microstructures of 1050 aluminum alloy prepared by equal channel angular pressing at cryogenic temperature (cryoECAP) after electric current annealing at 90–210 °C for 3 h were investigated by tensile test, electron back scattering diffraction (EBSD) and transmission electron microscopy (TEM). An unexpected annealing-induced strengthening phenomenon occurs at 90–210 °C, due to a significant decrease in the density of mobile dislocations after annealing, and thus a higher yield stress is required to nucleate alternative dislocation sources during tensile test. The electric current can enhance the motion of dislocations, lead to a lower dislocation density at 90–150 °C, and thus shift the peak annealing temperature from 150 °C to 120 °C. Moreover, the electric current can promote the migration of grain boundaries at 150–210 °C, result in a larger grain size at 150 °C and 210 °C, and thus causes a lower yield stress. The sample annealed with electric current has a lower uniform elongation at 90–120 °C, and the deviation in the uniform elongation between samples annealed without and with electric current becomes smaller at 150–210 °C. - Highlights: • An unexpected annealing-induced strengthening phenomenon occurs at 90–210 °C. • The d. c. current can enhance the motion of dislocations at 90–150 °C, and thus shift the peak annealing temperature from 150 °C to 120 °C. • The d. c. current can promote the grain growth at 150–210 °C, and thus cause a lower yield stress. • The DC annealed sample has a lower uniform elongation at 90–120 °C.

36 MATERIALS SCIENCE↗