Search NASA⌕ Search

SEARCH · Search NASA

Results for “HOVERING STABILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

A flight investigation of helicopter low-speed response requirements

A flight experiment has been conducted using the Canadian National Aeronautical Establishment's variable-stability airborne simulator to define the dynamic response requirements for operations at hover and low speeds. Fourteen Attitude Command/Attitude Hold, Rate, and Rate Command/Attitude Hold configurations were evaluated by six pilots using both conventional controls and a four-axis integrated sidestick over a low-speed course consisting of precision hover, landing, sidestep, and dash/quickstop tasks. The results indicate that with conventional controls all three response-types were acceptable as long as their response bandwidth was sufficiently high, and higher bandwidths were required in roll than in pitch. With the four-axis sidestick, there was a preference for the Rate systems. The range of acceptable bandwidths was lower, and the spread in pilot ratings smaller, than were found in a similar ground-based simulation.

Mitchell, David G.↗
NASA NTRS1993

Optimization-based controller design for rotorcraft

An optimization-based methodology for linear control system design is outlined by considering the design of a controller for a UH-60 rotorcraft in hover. A wide range of design specifications is taken into account: internal stability, decoupling between longitudinal and lateral motions, handling qualities, and rejection of windgusts. These specifications are investigated while taking into account physical limitations in the swashplate displacements and rates of displacement. The methodology crucially relies on user-machine interaction for tradeoff exploration.

Tsing, N.-K.↗
NASA NTRS1995

V/STOL systems research aircraft: A tool for cockpit integration

The next generation ASTOVL aircraft will have a complicated propulsion system. The configuration choices include Direct Lift, Lift-Fan and Lift + Lift/Cruise but the aircraft must also have supersonic performance and low-observable characteristics. The propulsion system may have features such as flow blockers, vectoring nozzles and flow transfer schemes. The flight control system will necessarily fully integrate the aerodynamic surfaces and the propulsive elements. With a fully integrated, fly-by-wire flight/propulsion control system, the options for cockpit integration are interesting and varied. It is possible to de-couple longitudinal and vertical responses allowing the pilot to close the loop on flightpath and flightpath acceleration directly. In the hover, the pilot can control the translational rate directly without having to stabilize the inner rate and attitude loops. The benefit of this approach, reduced workload and increased precision, has previously been demonstrated through several motion-based simulations. In order to prove the results in flight, the V/STOL System Research Aircraft (VSRA) was developed at the NASA Ames Research Center. The VSRA is the YAV-8B Prototype modified with a research flight control system using a series-parallel servo configuration in all the longitudinal degrees of freedom (including thrust and thrust vector angle) to provide an integrated flight and propulsion control system in a limited envelope. Development of the system has been completed and flight evaluations of the response types have been performed. In this paper we will discuss the development of the VSRA, the evolution of the flightpath command and translational rate command response types and the Guest Pilot evaluations of the system. Pilot evaluation results are used to draw conclusions regarding the suitability of the system to satisfy V/STOL requirements.

Stortz, Michael W.↗
NASA NTRS1997

Multidisciplinary Optimization of Tilt Rotor Blades Using Comprehensive Composite Modeling Technique

An optimization procedure is developed for addressing the design of composite tilt rotor blades. A comprehensive technique, based on a higher-order laminate theory, is developed for the analysis of the thick composite load-carrying sections, modeled as box beams, in the blade. The theory, which is based on a refined displacement field, is a three-dimensional model which approximates the elasticity solution so that the beam cross-sectional properties are not reduced to one-dimensional beam parameters. Both inplane and out-of-plane warping are included automatically in the formulation. The model can accurately capture the transverse shear stresses through the thickness of each wall while satisfying stress free boundary conditions on the inner and outer surfaces of the beam. The aerodynamic loads on the blade are calculated using the classical blade element momentum theory. Analytical expressions for the lift and drag are obtained based on the blade planform with corrections for the high lift capability of rotor blades. The aerodynamic analysis is coupled with the structural model to formulate the complete coupled equations of motion for aeroelastic analyses. Finally, a multidisciplinary optimization procedure is developed to improve the aerodynamic, structural and aeroelastic performance of the tilt rotor aircraft. The objective functions include the figure of merit in hover and the high speed cruise propulsive efficiency. Structural, aerodynamic and aeroelastic stability criteria are imposed as constraints on the problem. The Kreisselmeier-Steinhauser function is used to formulate the multiobjective function problem. The search direction is determined by the Broyden-Fletcher-Goldfarb-Shanno algorithm. The optimum results are compared with the baseline values and show significant improvements in the overall performance of the tilt rotor blade.

Chattopadhyay, Aditi↗
NASA NTRS1995

V/STOL Systems Research Aircraft: A Tool for Cockpit Integration

The next generation ASTOVL aircraft will have a complicated propulsion System. The configuration choices include Direct Lift, Lift-Fan and Lift+Lift /Cruise but the aircraft must also have supersonic performance and low-observable characteristics. The propulsion system may have features such as flow blockers, vectoring nozzles and flow transfer schemes. The flight control system will necessarily fully integrate the aerodynamic surfaces and the propulsive elements. With a fully integrated, fly-by-wire flight/propulsion control system, the options for cockpit integration are interesting and varied. It is possible to decouple longitudinal and vertical responses allowing the pilot to close the loop on flight path and flight path acceleration directly. In the hover, the pilot can control the translational rate directly without having to stabilize the inner rate and attitude loops. The benefit of this approach, reduced workload and increased precision. has previously been demonstrated through several motion-based simulations. In order to prove the results in flight, the V/STOL System Research Aircraft (VSRA) was developed at the NASA Ames Research Center. The VSRA is the YAV-8B Prototype modified with a research flight control system using a series-parallel servo configuration in all the longitudinal degrees of freedom (including thrust and thrust vector angle) to provide an integrated flight and propulsion control system in a limited envelope. Development of the system has been completed and flight evaluations of the response types have been performed. In this paper we will discuss the development of the VSRA, the evolution of the flight path command and translational rate command response types and the Guest Pilot evaluations of the system. Pilot evaluation results will be used to draw conclusions regarding the suitability of the system to satisfy V/STOL requirements.

Stortz, Michael W.↗
NASA NTRS1957

Flight Tests of a Model of a High-wing Transport Vertical-take-off Airplane with Tilting Wing and Propellers and with Jet Controls at the Rear of the Fuselage for Pitch and Yaw Control

An investigation of the stability and control of a high-wing transport vertical-take-off airplane with four engines during constant-altitude transitions from hovering to normal forward flight was conducted with a remotely controlled free-flight model. The model had four propellers distributed along the wing with the thrust axes in the wing chord plane. The wing could be rotated to 90 degrees incidence so that the propeller thrust axes were vertical for hovering flight. An air jet at the rear of the fuselage provided pitch and yaw control for hovering and low-speed flight.

CONTROL, LONGITUDINAL↗
NASA NTRS2004

A New Approach to Attitude Stability and Control for Low Airspeed Vehicles

This paper describes an approach for controlling the attitude of statically unstable thrust-levitated vehicles in hover or slow translation. The large thrust vector that characterizes such vehicles can be modulated to provide control forces and moments to the airframe, but such modulation is accompanied by significant unsteady flow effects. These effects are difficult to model, and can compromise the practical value of thrust vectoring in closed-loop attitude stability, even if the thrust vectoring machinery has sufficient bandwidth for stabilization. The stabilization approach described in this paper is based on using internal angular momentum transfer devices for stability, augmented by thrust vectoring for trim and other "outer loop" control functions. The three main components of this approach are: (1) a z-body axis angular momentum bias enhances static attitude stability, reducing the amount of control activity needed for stabilization, (2) optionally, gimbaled reaction wheels provide high-bandwidth control torques for additional stabilization, or agility, and (3) the resulting strongly coupled system dynamics are controlled by a multivariable controller. A flight test vehicle is described, and nonlinear simulation results are provided that demonstrate the efficiency of the approach.

Lim, K. B.↗
NASA NTRS2001

A Wind-Tunnel Parametric Investigation of Tiltrotor Whirl-Flutter Stability Boundaries

A wind-tunnel investigation of tiltrotor whirl-flutter stability boundaries has been conducted on a 1/5-size semispan tiltrotor model known as the Wing and Rotor Aeroelastic Test System (WRATS) in the NASA-Langley Transonic Dynamics Tunnel as part of a joint NASA/Army/Bell Helicopter Textron, Inc. (BHTI) research program. The model was first developed by BHTI as part of the JVX (V-22) research and development program in the 1980's and was recently modified to incorporate a hydraulically-actuated swashplate control system for use in active controls research. The modifications have changed the model's pylon mass properties sufficiently to warrant testing to re-establish its baseline stability boundaries. A parametric investigation of the effect of rotor design variables on stability was also conducted. The model was tested in both the on-downstop and off-downstop configurations, at cruise flight and hover rotor rotational speeds, and in both air and heavy gas (R-134a) test mediums. Heavy gas testing was conducted to quantify Mach number compressibility effects on tiltrotor stability. Experimental baseline stability boundaries in air are presented with comparisons to results from parametric variations of rotor pitch-flap coupling and control system stiffness. Increasing the rotor pitch-flap coupling (delta(sub 3) more negative) was found to have a destabilizing effect on stability, while a reduction in control system stiffness was found to have little effect on whirl-flutter stability. Results indicate that testing in R-134a, and thus matching full-scale tip Mach number, has a destabilizing effect, which demonstrates that whirl-flutter stability boundaries in air are unconservative.

Piatak, David J.↗
NASA NTRS1988

Rotorcraft handling-qualities design criteria development

Joint NASA/Army efforts at the Ames Research Center to develop rotorcraft handling-qualities design criteria began in earnest in 1975. Notable results were the UH-1H VSTOLAND variable stability helicopter, the VFA-2 camera-and-terrain-board simulator visual system, and the generic helicopter real-time mathematical model, ARMCOP. An initial series of handling-qualities studies was conducted to assess the effects of rotor design parameters, interaxis coupling, and various levels of stability and control augmentation. The ability to conduct in-flight handling-qualities research was enhanced by the development of the NASA/Army CH-47 variable-stability helicopter. Research programs conducted using this vehicle include vertical-response investigations, hover augmentation systems, and the effects of control-force characteristics. The handling-qualities data base was judged to be sufficient to allow an update of the military helicopter handling-qualities specification, MIL-H-8501. These efforts, including not only the in-house experimental work but also contracted research and collaborative programs performed under the auspices of various international agreements. The report concludes by reviewing the topics that are currently most in need of work, and the plans for addressing these topics.

Aiken, Edwin W.↗
NASA NTRS1989

Simulation evaluation of transition and hover flying qualities of a mixed-flow, remote-lift STOVL aircraft

Using a generalized simulation model developed for piloted evaluations of STOVL aircraft, an initial fixed-base simulation of a mixed-flow, remote-lift configuration has been completed. Objectives were to evaluate the integration of the aircraft's flight and propulsion controls to achieve good flying qualities throughout the low-speed flight envelope; to determine control power used during transition, hover, and vertical landing; and to evaluate the transition flight envelope considering the influence of thrust deflection of the remote-lift component. Pilots' evaluations indicated that Level 1 flying qualities could be achieved for deceleration to hover in instrument conditions, for airfield landings, and for recovery to a small ship when attitude and velocity stabilization and command augmentation control modes were provided. Level 2 flying qualities were obtained for these same tasks when only the attitude command mode was used, leaving the pilot to perform the task of thrust management required to control the flight-path and speed in transition and the horizontal and vertical translational velocities in hover. Thrust margins were defined for vertical landing as a function of ground effect and hot-gas ingestion.

Franklin, James A.↗
NASA NTRS1973

Nonlinear Equations for Bending of Rotating Beams with Application to Linear Flap-Lag Stability of Hingeless Rotors

The nonlinear partial differential equations for the flapping and lead-lag degrees of freedom of a torisonally rigid, rotating cantilevered beam are derived. These equations are linearized about an equilibrium condition to study the flap-lag stability characteristics of hingeless helicopter rotor blades with zero twist and uniform mass and stiffness in the hovering flight condition. The results indicate that these configurations are stable because the effect of elastic coupling more than compensates for the destabilizing flap-lag Coriolis and aerodynamic coupling. The effect of higher bending modes on the lead-lag damping was found to be small and the common, centrally hinged, spring restrained, rigid blade approximation for elastic rotor blades was shown to be resonably satisfactory for determining flap-lag stability. The effect of pre-cone was generally stabilizing and the effects of rotary inertia were negligible.

Hodges, D. H.↗
NASA NTRS1976

Aeroelastic stability of complete rotors with application to a teetering rotor in forward flight

The derivation of a set of nonlinear coupled flap-lag-torsion equations of motion for moderately large deflections of an elastic, two bladed teetering helicopter rotor in forward flight is concisely outlined. The following degrees of freedom are included in the mathematical model: rigid body flapping, rigid body lead lag, elastic bending in flap and lead-lag blade root torsion and shaft torsion. Quasi-steady aerodynamic loads are considered and the effects of reversed flow are included. The aeroelastic stability of the complete rotor is investigated using a linearized system of equations of motion. The equilibrium position about which the equations are linearized is obtained by considering the trim state of the helicopter, in true or simulated forward flight conditions. The sensitivity of the aeroelastic stability boundaries to interblade structural and mechanical coupling is illustrated by comparing the complete rotor stability boundaries with those obtained from a single blade analysis for a number of hover and forward flight cases.

Shamie, J.↗
NASA NTRS1977

Aeroelastic stability of complete rotors with application to a teetering rotor in forward flight

The derivation of a set of non-linear coupled flap-lag-torsion equations of motion for moderately large deflections of an elastic, two-bladed teetering helicopter rotor in forward flight is concisely outlined. The following degrees of freedom are included in the mathematical model: rigid body flapping, rigid body lead-lag, elastic bending in flap and lead-lag, blade root torsion, and shaft torsion. Quasi-steady aerodynamic loads are considered and the effects of reversed flow are included. The aeroelastic stability of the complete rotor is investigated by using a linearized system of equations of motion. The equilibrium position about which the equations are linearized is obtained by considering the trim state of the helicopter, in true or simulated forward flight conditions. The sensitivity of the aeroelastic stability boundaries to interblade structural and mechanical coupling is illustrated by comparing the complete rotor stability boundaries with those obtained from a single blade analysis for a number of hover and forward flight cases.

Shamie, J.↗
NASA NTRS1997

Transfer of the CONSOL-OPTCAD Rotorcraft Design Tool to Industry

Significant progress was made. Initial results on the improvement of the user-friendliness and useability of GIFCORCODE led to the decision to provide GIFCORCODE with a menu-driven user interface. In collaboration with staff at Moffett field and students from Cal Poly this objective has been largely met. GIFCORCODE is now menu-driven and very much easier to use. Complete designs for stability and control augmentation systems for the UH-60A ADOCS/RASCAL rotorcraft in both hover and 80 knots forward flight have been completed and documented. The originally planned presentations to industry were deferred so the new user interface for GIFCORCODE could be completed. The industry presentations are now planned for the next year. Similarly, the work on preparing a short course on the use of GIFCORCODE was deferred. The details of the original goals for this contract are presented in this report. The modifications to these goals and the reasons for them are also described. This is followed by a section containing the results of work on this contract. A final section, conclusions, contains suggestions for future work on this project.

Levine, William S.↗
NASA NTRS1953

Flight Investigation of the Stability and Control Characteristics of a 0.13-Scale Model of the Convair XFY-1 Vertically Rising Airplane During Constant-Altitude Transitions, TED No. NACA DE 368

An investigation is being conducted to determine the dynamic stability and control characteristics of a 0.13-scale flying model of the Convair XFY-1 vertically rising airplane. This paper presents the results of flight tests to determine the stability and control characteristics of the model during constant-altitude slow transitions from hovering to normal unstalled forward flight. The tests indicated that the airplane can be flown through the transition range fairly easily although some difficulty will probably encountered in controlling the yawing motions at angles of attack between about 60 and 40. An increase in the size of the vertical tail will not materially improve the controllability of the yawing motions in this range of angle of attack but the use of a yaw damper will make the yawing motions easy to control throughout the entire transitional flight range. The tests also indicated that the airplane can probably be flown sideways satisfactorily at speeds up to approximately 33 knots (full scale) with the normal control system and up to approximately 37 knots (full scale) with both elevons and rudders rigged to move differentially for roll control. At sideways speeds above these values, the airplane will have a strong tendency to diverge uncontrollably in roll.

Lovell, Powell M., Jr.↗
NASA NTRS1956

Flight Investigation of the Stability and Control Characteristics of Vertically Rising Airplane Research Model with Swept or Unswept Wings and X- or +-tails

The take-off, landing, hovering, and transition flight characteristics of a propeller-driven, fighter-type, vertically rising airplane model were obtained from time histories of the flights and from the pilots' opinions of the flight characteristics. In general, there were no major differences in the behavior of any of the configurations, all of which performed satisfactorily.

CONTROL, LATERAL↗
NASA NTRS1981

Development and validation of the V/STOL aerodynamics and stability and control manual

A V/STOL Aerodynamics and Stability and Control Manual was developed to provide prediction methods which are applicable to a wide range of V/STOL configurations in hover and transition flight, in and out of ground effect. Propulsion-induced effects have been combined with unpowered aerodynamics in a buildup of total forces and moments for the jet-lift concept, so that total aerodynamics can be used to predict aircraft stability, control, and flying qualities characteristics. Results of longitudinal aerodynamic predictions have been compared with test data, and indicate that the methods are fast, inexpensive, and within the desired accuracy for the objective preliminary design stage.

Henderson, C.↗