Search NASA⌕ Search

SEARCH · Search NASA

Results for “Interference Effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Static longitudinal aerodynamic characteristics of close-coupled wing-canard configurations at Mach numbers from 1.60 to 2.86

An experimental investigation was made in the Mach number range from 1.60 to 2.86 to determine the static longitudinal aerodynamic characteristics of close-coupled wing-canard configurations. Three canards, ranging in exposed planform area from 17.5 to 30.0 percent of the wing reference area, were employed in this investigation. The canards were either located in the plane of the wing or in a position 18.5 percent of the wing mean geometric chord above the wing plane. Most data obtained were for a model with a 60 deg leading-edge-sweep wing; however, a small amount of data were obtained for a 44 deg leading-edge-sweep wing. The model utilized two balances to isolate interference effects between wing and canard. In general, it was determined that at angle of attack for all configurations investigated with the canard in the plane of the wing an unfavorable interference exists which causes the additional lift on the canard generated by a canard deflection to be lost on the wing due to an increased downwash at the wing from the canard. Further, this interference decreased somewhat with increasing Mach number. Raising the canard above the plane of the wing also greatly decreased the interference of the canard deflection on the wing lift. However, at Mach 2.86 the presence of the canard in the high position had a greater unfavorable interference effect at high angles of attack than the canard in the wing plane. This interference resulted in the in-plane canard having better trimmed performance at Mach 2.86 for the same center-of-gravity location.

Dollyhigh, S. M.↗
NASA NTRS1985

Numerical study of three-dimensional turbulent flow interactions between blockage models and wind tunnels including longitudinally slotted test sections

A spatial forward-marching approach is applied to compute three-dimensional turbulent flows for several blockage models in free flight, in a solid wall wind tunnel, and in a wind tunnel with longitudinal slots in the test section. The effects of area blockage in the tunnel, model growth and tunnel wall boundary layers, and of the slots are included. The large blockage models are found to have significant wall interference effects which can be reduced by the slots. The effects of the latter are confined to the region near the tunnel wall. Model/wall interference effects are not limited to the effects of area blockage; in particular, boundary layer profile shapes for a wind tunnel model in a tunnel are different from shapes for a model in free flight even when slots are used. This indicates that the flow responds differently in these two cases with the same pressure gradient.

Lin, S.-J.↗
NASA NTRS1976

Analytical Work in Support of the Design and Operation of Two Dimensional Self Streamlining Test Sections

A method has been developed for accurately computing the imaginary flow fields outside a flexible walled test section, applicable to lifting and non-lifting models. The tolerances in the setting of the flexible walls introduce only small levels of aerodynamic interference at the model. While it is not possible to apply corrections for the interference effects, they may be reduced by improving the setting accuracy of the portions of wall immediately above and below the model. Interference effects of the truncation of the length of the streamlined portion of a test section are brought to an acceptably small level by the use of a suitably long test section with the model placed centrally.

Judd, M.↗
NASA NTRS1976

Unsteady aerodynamic flow field analysis of the space shuttle configuration. Part 4: 747/orbiter aeroelastic stability

A quasi-steady analysis of the aeroelastic stability of the lateral (antisymmetric) modes of the 747/orbiter vehicle was accomplished. The interference effect of the orbiter wake on the 747 tail furnishes an aerodynamic undamping contribution to the elastic modes. Likewise, the upstream influence of the 747 tail and aft fuselage on the orbiter beaver-tail rail fairing also is undamping. Fortunately these undamping effects cannot overpower the large damping contribution of the 747 tail and the modes are damped for the configurations analyzed. However, significant interference effects of the orbiter on the 747 tail have been observed in the pitch plane. The high response of the 747 vertical tail in the orbiter wave was also considered. Wind tunnel data points to flapping of the OMS pod wakes as the source of the wake resonance phenomenon.

Reding, J. P.↗
NASA NTRS1989

Experience with some repeat tests on the 9 inch chord CAST-10-2/DOA 2 airfoil model in the Langley 0.3-m TCT adaptive wall test section

A co-operative testing program is in progress between the Langley Research Center (NASA) and the National Aeronautical Establishment (NAE, Canada) to validate two different techniques of airfoil testing at transonic speeds. The procedure employed is to test the same airfoil model in the NAE two-dimensional tunnel and the Langley 0.3-m Transonic Cryogenic Tunnel (0.3-m TCT). The airfoil model used in testing was CAST-10-2/DOA-2 super-critical airfoil. The Langley 0.3-m TCT has a relatively small cross section of 13 in x 13 in, giving a (h/c) ratio of 1.44 for the same 9 in chord model. The approach employed in the 0.3-m TCT aims towards eliminating the wall effects by using active walls. The top and bottom walls are flexible. By changing the wall shapes during a test in an iterative manner, the wall interference effects are reduced. The method employed to change the wall shapes is the adaptive wall technique. The current test program provided an opportunity to validate the adaptive wall technique in the 0.3-m TCT. The relatively long chord airfoil represents a severe test case to test the efficacy of the adaptive wall technique under cryogenic conditions. The program also involved removal of side wall boundary-layer thus increasing the complexity of the wall adaptation technique. This paper deals with some salient results obtained regarding repeatability of test data and possible residual interference effects.

Murthy, A. V.↗
NASA NTRS1975

Effect of empennage interference on single-engine afterbody/nozzle drag

An investigation has been conducted in the Langley 16-foot transonic tunnel to determine the effects of empennage surfaces on single-engine afterbody and nozzle drag at Mach numbers up to 1.20. Empennage interference drag was obtained by using experimental values of afterbody/nozzle drag and theoretical values of empennage drag. Three methods for minimizing adverse empennage interference effects were investigated. Results show that empennage interference effects were always detrimental but could be reduced by proper location of tail surfaces. Afterbody contouring and addition of 'contour' bumps were generally ineffective in reducing aft-end drag for Mach numbers less than 0.95.

Berrier, B. L.↗
NASA NTRS1972

Flow interference in a variable porosity trisonic wind tunnel.

Pressure data from a 20-degree cone-cylinder in a variable porosity wind tunnel for the Mach range 0.2 to 5.0 are compared to an interference free standard in order to determine wall interference effects. Four 20-degree cone-cylinder models representing an approximate range of percent blockage from one to six were compared to curve-fits of the interference free standard at each Mach number and errors determined at each pressure tap location. The average of the absolute values of the percent error over the length of the model was determined and used as the criterion for evaluating model blockage interference effects. The results are presented in the form of the percent error as a function of model blockage and Mach number.

Davis, J. W.↗
NASA NTRS1984

Experiences with a high-blockage model tested in the NASA Ames 12-foot pressure wind tunnel

Representation of the flow around full-scale ships was sought in the subsonic wind tunnels in order to a Hain Reynolds numbers as high as possible. As part of the quest to attain the largest possible Reynolds number, large models with high blockage are used which result in significant wall interference effects. Some experiences with such a high blockage model tested in the NASA Ames 12-foot pressure wind tunnel are summarized. The main results of the experiment relating to wind tunnel wall interference effects are also presented.

Coder, D. W.↗
NASA NTRS1992

Installation effects of wing-mounted turbofan nacelle-pylons on a 1/17-scale, twin-engine, low-wing transport model

A twin-engine, low-wing transport model, with a supercritical wing of aspect ratio 10.8 designed for a cruise Mach number of 0.77 and a lift coefficient of 0.55, was tested in the Langley 16-Foot Transonic Tunnel. The purpose of this test was to compare the wing-nacelle interference effects of flow-through nacelles simulating superfan engines (very high bypass ratio (BPR is approx. = 18) turbofan engines) with the wing-nacelle interference effects of current-technology turbofans (BPR is approx. = 6). Forces and moments on the complete model were measured with a strain-gage balance, and extensive external static-pressure measurements (383 orifice locations) were made on the wing, nacelles, and pylons of the model. Data were taken at Mach numbers from 0.50 to 0.80 and at model angles of attack from -4 deg to 8 deg. Test results indicate that flow-through nacelles with a very high bypass ratio can be installed on a low-wing transport model with a lower installation drag penalty than for a conventional turbofan nacelle at a design cruise Mach number of 0.77 and lift coefficient of 0.55.

Pendergraft, Odis C., Jr.↗
NASA NTRS1972

Reduction of wave drag by antisymmetric arrangement of wings and bodies.

The wave interference effects for bodies or wings in a mirror-symmetric arrangement, and in an antisymmetric arrangement are discussed. It is shown that while in the case of a mirror-symmetric arrangement large adverse interference effects can be observed, antisymmetric arrangements provide comparatively much smaller wave drags. The single continuous wing panels also adapt themselves more readily to varying angles of obliquity, and hence, to varying flight speeds. A detailed review is presented of the previous work on the aerodynamic properties and flight stability of oblique elliptic wing combinations. A possible mode of application of these combinations to transport aircraft operating at moderate supersonic speeds is suggested.

Jones, R. T.↗
NASA NTRS1990

Scattering properties of woven fibrous insulations - Effects of interference for normal incidence

This paper examines the scattering properties of woven fibrous materials in order to model the interactions between the scattered radiation from individual fibers. A normally incident plane electromagnetic wave is considered and different representative geometries are analyzed theoretically. Experimental results are presented for specific woven thermal insulation fabrics. Previous studies in the literature have mostly ignored the effect of constructive or destructive addition of scattered waves from individual fibers with the exception of the case of parallel fibers. Whereas the light-scattering characteristics of a single long fiber depend only on the size parameter and on the material optical constants, the additional mechanism of interference between the scattered waves from fibers of parallel or perpendicular orientation introduces an additional dependence on fiber locations. In this study, analytical models are developed for obtaining the radiative scattering characteristics of woven fibrous media taking into account the mechanism of interference. Experimental measurements of forward- and backward-scattered light from a woven silica cloth over a broad range of wavelengths in the infrared are obtained and compared with the predicted results for a system of two orthogonal families of infinite parallel fibers.

Kumar, Sunil↗
NASA NTRS1987

Aerodynamic analysis for aircraft with nacelles, pylons, and winglets at transonic speeds

A computational method has been developed to provide an analysis for complex realistic aircraft configurations at transonic speeds. Wing-fuselage configurations with various combinations of pods, pylons, nacelles, and winglets can be analyzed along with simpler shapes such as airfoils, isolated wings, and isolated bodies. The flexibility required for the treatment of such diverse geometries is obtained by using a multiple nested grid approach in the finite-difference relaxation scheme. Aircraft components (and their grid systems) can be added or removed as required. As a result, the computational method can be used in the same manner as a wind tunnel to study high-speed aerodynamic interference effects. The multiple grid approach also provides high boundary point density/cost ratio. High resolution pressure distributions can be obtained. Computed results are correlated with wind tunnel and flight data using four different transport configurations. Experimental/computational component interference effects are included for cases where data are available. The computer code used for these comparisons is described in the appendices.

Boppe, Charles W.↗
NASA NTRS1952

Analysis of the effects of wing interference on the tail contributions to the rolling derivatives

An analysis of the effects of wing interference on the tail contributions to the rolling stability derivatives of complete airplane configurations is made by calculating the angularity of the air stream at the vertical tail due to rolling and determining the resulting forces and moments. Some of the important factors which affect the resultant angularity on the vertical tail are wing aspect ratio and sweepback, vertical-tail span, and considerations associated with angle of attack and airplane geometry. Some calculated sidewash results for a limited range of plan forms and vertical-tail sizes are presented. Equations taking into account the sidewash results are given for determining the tail contributions to the rolling derivatives. Comparisons of estimated and experimental results indicate that a consideration of wing interference effects improves the estimated values of the tail contributions to the rolling derivatives and that fair agreement with available experimental data is obtained.

Michael, William H , Jr↗
NASA NTRS1989

Wind tunnel wall interference investigations in NAE/NRC High Reynolds Number 2D Facility and NASA Langley 0.3m Transonic Cryogenic Tunnel

Results are reported from a NAE/NRC and NASA cooperative program on two-dimensional wind-tunnel wall-interference research, aimed at developing the technology for correcting or eliminating wall interference effects in two-dimensional transonic wind-tunnel investigations. Both NASA Langley and NAE facilities are described, along with a NASA-designed and fabricated airfoil model. It is shown that data from the NAE facility, corrected for wall interference, agree with those obtained from the NASA tunnel, which has adaptive walls; the comparison of surface pressure data shows that the flowfield conditions in which the model is investigated appear to be nearly identical under most conditions. It is concluded that both approaches, posttest correction and an adaptive wall, adequately eliminate the tunnel-wall interference effects.

Chan, Y. Y.↗
NASA NTRS1958

Longitudinal and Lateral Stability and Control Characteristics of Various Combinations of the Component Parts of Two Canard Airplane Configurations at Mach Numbers of 1.41 and 2.01

An investigation has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel to determine the aerodynamic characteristics in pitch and sideslip of a generalized canard airplane model. Two wings of equal area but differing in plan form were investigated. The model was equipped with a trapezoidal canard surface with an area 12 percent of the wing area, a low-aspect-ratio vertical tail, and twin ventral fins. The interference effects of the canard wake on the wing result in little or no gain in the total lift at a Mach number of 1.41 but at a Mach number of 2.01 a substantial portion of the canard lift is retained with a resultant increase in total lift. Because these interference effects of the canard wake appear to be concentrated near the leading edge of the wing, the proper location of the wing leading edge with respect to the center of moments may result in a substantial increase in the moment increment provided by a canard surface even though the total lift provided by the canard is small. For these configurations the trapezoidal wing retained the most lift and had the largest favorable moment increment produced by the canards. The canard configurations have the same characteristic decrease in directional-stability with angle of attack as most conventional high-fineness-ratio supersonic configurations. Although the presence of the canard surface caused a small increase in the directional stability at a Mach number of 1.41 for the delta-wing configuration, the presence of the canards resulted in small decreases in the directional-stability level at a Mach number of 2.01 for both wing configurations. A canard deflection of 15 deg provides an increase in the positive effective dihedral approximately as large as that provided by the presence of the vertical tail. This effect of canard deflection might complicate the lateral-control problem in the case of a rolling pull-up maneuver.

Driver, Cornelius↗
NASA NTRS1987

Experimental and theoretical study of propeller spinner/shank interference

A fundamental investigation into the aerodynamic interference associated with propeller spinner and shank regions has been conducted. The research program involved a theoretical assessment of solutions previously proposed, followed by a systematic experimental study to supplement the existing data base. As a result, a refined computational procedure has been established for prediction of interference effects in terms of either interference drag or propeller thrust and torque coefficients. These quantities have been examined with attention to engineering parameters such as spinner finess ratio, blade shank form, and number of blades. Also, cascade effects and spinner/shank juncture interference have been semi-empirically modeled using existing theories and placed into a compatible form with an existing propeller performance code.

Cornell, C. C.↗
NASA NTRS1979

The effect of interference on delta modulation encoded video signals

The results of a study on the use of the delta modulator as a digital encoder of television signals are presented. The computer simulation was studied of different delta modulators in order to find a satisfactory delta modulator. After finding a suitable delta modulator algorithm via computer simulation, the results are analyzed and then implemented in hardware to study the ability to encode real time motion pictures from an NTSC format television camera. The effects were investigated of channel errors on the delta modulated video signal and several error correction algorithms were tested via computer simulation. A very high speed delta modulator was built (out of ECL logic), incorporating the most promising of the correction schemes, so that it could be tested on real time motion pictures. The final area of investigation concerned itself with finding delta modulators which could achieve significant bandwidth reduction without regard to complexity or speed. The first such scheme to be investigated was a real time frame to frame encoding scheme which required the assembly of fourteen, 131,000 bit long shift registers as well as a high speed delta modulator. The other schemes involved two dimensional delta modulator algorithms.

Schilling, D. L.↗
NASA NTRS1988

Miniaturized compact water-cooled pitot-pressure probe for flow-field surveys in hypersonic wind tunnels

An experimental investigation of the design of pitot probes for flowfield surveys in hypersonic wind tunnels is reported. The results show that a pitot-pressure probe can be miniaturized for minimum interference effects by locating the transducer in the probe support body and water-cooling it so that the pressure-settling time and transducer temperature are compatible with hypersonic tunnel operation and flow conditions. Flowfield surveys around a two-to-one elliptical cone model in a 20-inch Mach 6 wind tunnel using such a probe show that probe interference effects are essentially eliminated.

Ashby, George C.↗