SEARCH · Search NASA

Results for “LIFT CURVES - SLOPE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1946

Wind-Tunnel Investigation of the Horizontal Motion of a Wing Near the Ground

By the method of images the horizontal steady motion of a wing at small heights above the ground was investigated in the wind tunnel, A rectangular wing with Clark Y-H profile was tested with and without flaps. The distance from the trailing edge of the wing to the ground was varied within the limits 0.75 less than or = s/c less than or = 0.25. Measurements were made of the lift, the drag, the pitching moment, and the pressure distribution at one section. For a wing without flaps and one with flaps a considereble decrease in the lift force and a,drop in the drag was obtained at angles of attack below stalling. The flow separation near the ground occurs at smaller angles of attack than is the case for a great height above the ground. At horizontal steady flight for practical values of the height above the ground the maximum lift coefficient for the wing without flaps changes little, but markedly decreases for the wing with flaps. Analysis of these phenomena involves the investigation of the pressure distribution. The pressure distribution curves showed that the changes occurring near the ground are not equivalent to a change in the angle of attack. At the lower surface of the section a very strong increase in the pressures is observed. The pressure changes on the upper surface at angles of attack below stalling are insignificant and lead mainly to an increase in the unfavorable pressure gradient, resulting in the earlier occurrence of separation. For a wing with flaps at large angles of attack for distances from the trailing edge of the flap to the ground less than 0.5 chord, the flow between the wing end the ground is retarded so greatly that the pressure coefficient at the lower surface of the section is very near its limiting value (P = 1), and any further possibility of increase in the pressure is very small. In the application an approximate computation procedure is given of the change of certain aerodynamic characteristics for horizontal steady flight near the ground.

Serebrisky, Y. M.↗

NASA NTRS1984

Observations from varying the lift and drag inputs to a noise prediction method for supersonic helical tip speed propellers

Previous comparisons between calculated and measured supersonic helical tip speed propeller noise show them to have different trends of peak blade passing tone versus helical tip Mach number. It was postulated that improvements in this comparison could be made first by including the drag force terms in the prediction and then by reducing the blade lift terms at the tip to allow the drag forces to dominate the noise prediction. Propeller hub to tip lift distributions were varied, but they did not yield sufficient change in the predicted lift noise to improve the comparison. This result indicates that some basic changes in the theory may be needed. In addition, the noise predicted by the drag forces did not exhibit the same curve shape as the measured data. So even if the drag force terms were to dominate, the trends with helical tip Mach number for theory and experiment would still not be the same. The effect of the blade shock wave pressure rise was approxmated by increasing the drag coefficient at the blade tip. Predictions using this shock wdave approximation did have a curve shape similar to the measured data. This result indicates that the shock pressure rise probably controls the noise at supersonic tip speed and that the linear prediction method can give the proper noise trend with Mach number.

Dittmar, J. H.↗

NASA NTRS1994

Parameters of Nocilla gas/surface interaction model from measured accomodation coefficients

Free-molecule aerodynamic coefficients are computed for a flat plate surface element at various angles of attack using the normal and tangential accomodation coefficients and the Nocilla model of the gas/surface interaction. The Nocilla model assumes that the molecules reflect from a surface in the form of a drifting Maxwellian with a mean velocity at a specific temperature. The computations use curve fits of the angular variation of the existing measurements of the accomodation coefficients and of the parameters in the Nocilla model. The two methods indicate that a surface element has considerably more lift than predicted by an assumption of diffuse scattering. In other respects the predictions by the two methods do not agree.

Collins, Frank G.↗

NASA NTRS1940

Aerodynamic characteristics of horizontal tail surfaces

Collected data are presented on the aerodynamic characteristics of 17 horizontal tail surfaces including several with balanced elevators and two with end plates. Curves are given for coefficients of normal force, drag, and elevator hinge moment. A limited analysis of the results has been made. The normal-force coefficients are in better agreement with the lifting-surface theory of Prandtl and Blenk for airfoils of low aspect ratio than with the usual lifting-line theory. Only partial agreement exists between the elevator hinge-moment coefficients and those predicted by Glauert's thin-airfoil theory.

Silverstein, Abe↗

NASA NTRS1948

Tank Tests of a Powered Model of a Compression Plane, NACA Model 171A-2

The compression plane is intended for operation on or close to the surface of the water, and has a hull with a concave bottom which forms the upper surface of a tunnel into which air is forced under pressure to support part of the load. The results of the tests made in Langley tank no. 1 include values of the horizontal forces, trimming moment, and static pressure in the tunnel for a wide range of loads and speeds and two power conditions, and are presented in the form of curves against speed with load as a parameter. The results are scaled up to 10 times the model size for three conditions at which the model is self-propelled at a steady speed. Lift is obtained from the static pressure of air in the tunnel. In general, the ratio of the gross load to the total resistance increases with increase in load and decrease in speed. This ratio varies between l-7 and 5.7 at high speeds and has a maximum value of 7. The total resistance is nearly the same for both power conditions except at low speeds and heavy loads. No abrupt change in forces on the hull or flow around the hull occurs in. the region of zero draft. The centers of pressure are generally far aft. At the most efficient trim (1.2'), considerable bow-up moment would be required for practicable operation. There is no abrupt transition from the air-borne to the water- borne condition.

Mottard, Elmo J.↗

NASA NTRS1971

Flight-determined aerodynamic stability and control derivatives of the M2-F2 lifting body vehicle at subsonic speeds

Aerodynamic derivatives were obtained for the M2-F2 lifting body flight vehicle in the subsonic flight region between Mach numbers of 0.41 and 0.64 and altitudes of 7000 feet to 45,000 feet. The derivatives were determined by a flight time history curve-fitting process utilizing a hybrid computer. The flight-determined derivatives are compared with wind-tunnel and predicted values. Modal-response characteristics, calculated from the flight derivatives, are presented.

Kempel, R. W.↗

NASA NTRS1971

Mars surface sample return missions via solar electric propulsion

The characteristics and capabilities are described of solar electric propulsion (SEP) for performing Mars Surface Sample Return (MSSR) missions. The scope of the study emphasizes trajectory/payload analysis and the comparison of mission/system tradeoff options. The MSSR mission is examined only for the 1981-82 launch opportunity. Several other study constraints which bear directly on the results obtained are: (1) return samples in the range 5-25 kg, (2) use of lifting (offset C.G.) atmospheric entry at Mars which allows a low ratio (1.25) of entry weight to landed weight, and (3) rendezvous and docking in Mars orbit. Major results of the study are presented as performance curves of earth departure mass versus sample size for a number of different mission/system options. These options represent a spectrum of trip time, launch vehicle capability, combinations of low-thrust and ballistic maneuvers, chemical retro type, and earth recovery mode.

Spadoni, D. J.↗

NASA NTRS1989

Performance of an aero-space plane propulsion nozzle

An inviscid and viscous analysis is provided for an exposed half nozzle that is used with a scramjet for thrust generation. The analysis is based on the inviscid theory of a two-dimensional, minimum length nozzle with a curved inlet surface, where the flow may be sonic or supersonic. Inlet conditions are prescribed and the gas is assumed to be perfect. Viscous, and when appropriate inviscid, nondimensional parametric results are provided for the thrust, lift, heat transfer, pitching moment, and a variety of boundary-layer thicknesses. In addition to global results, wall distributions of pressure, heat transfer, etc., are provided. The analysis demonstrates that the nozzle produces a considerable lift force whose magnitude may exceed the thrust and a significant pitching moment. The thrust is quite sensitive to the inlet Mach number; it rapidly decreases as the inlet Mach number increases There is little loss in the thrust as the nozzle's downstream wall is truncated. The corresponding decrease in lift and the pitching moment is moderate.

Emanuel, George↗

NASA NTRS1978

A three-dimensional potential-flow program with a geometry package for input data generation

Information needed to run a computer program for the calculation of the potential flow about arbitrary three dimensional lifting configurations is presented. The program contains a geometry package which greatly reduces the task of preparing the input data. Starting from a very sparse set of coordinate data, the program automatically augments and redistributes the coordinates, calculates curves of intersection between components, and redistributes coordinates in the regions adjacent to the intersection curves in a suitable manner for use in the potential flow calculations. A brief summary of the program capabilities and options is given, as well as detailed instructions for the data input, a suggested structure for the program overlay, and the output for two test cases.

Halsey, N. D.↗

NASA NTRS2001

The Impact on Simulated Storm Structure and Intensity of Variations in the Lifted Condensation Level and the Level of Free Convection

The sensitivities of convective storm structure and intensity to changes in the altitudes of the prestorm environmental lifted condensation level and level of free convection axe studied using a full-physics three-dimensional cloud model. Matrices of simulations are conducted for a range of LCL=LFC altitudes, using a single moderately-sheared curved hodograph trace in conjunction with 1 convective available potential energy values of either 800 or 2000 J/kg, with the matrices consisting of all four combinations of two distinct choices of buoyancy and shear profile shape. For each value of CAPE, the LCL=LFC altitudes are also allowed to vary in a series of simulations based on the most highly compressed buoyancy and shear profiles for that CAPE, with the environmental buoyancy profile shape, subcloud equivalent potential temperature, subcloud lapse rates of temperature and moisture, and wind profile held fixed. For each CAPE, one final simulation is conducted using a near optimal LFC, but a lowered LCL, with a neutrally buoyant environmental thermal profile specified in between. Results show that, for the buoyancy-starved small-CAPE environments, the simulated storms are supercells and are generally largest and most intense when LCL=LFC altitudes lie in the approximate range 1.5-2.5 km above the surface. The simulations show similar trends for the shear-starved large-CAPE environments, except that conversion from supercell to multicell morphology frequently occurs when the LCL is high. For choices of LCL=LFC height within the optimal 1.5-2.5 km range, peak storm updraft overturning efficiency may approaches unity relative to parcel theory, while for lower LCL=LFC heights, overturning efficiency is reduced significantly. The enhancements of overturning efficiency and updraft diameter with increasing LFC height are shown to be the result of systematic increases in the mean equivalent potential temperature of the updraft at cloud base. For the shear-starved environments, the tendency for outflow dominance is eliminated, but a large overturning efficiency maintained, when a low LCL is used in conjunction with a high LFC. The result regarding outflow dominance at high LCL is consistent with expectations, but the beneficial effect of a high LFC on convective overturning efficiency has not previously been widely recognized. The simulation findings here also appear to be consistent with statistics from previous severe storm environment climatologies, but provide a new framework for interpreting those statistics.

McCaul, Eugene W., Jr.↗

NASA NTRS2010

Large Spun Formed Friction-Stir Welded Tank Domes for Liquid Propellant Tanks Made from AA2195: A Technology Demonstration for the Next Generation of Heavy Lift Launchers

Improving structural efficiency while reducing manufacturing costs are key objectives when making future heavy-lift launchers more performing and cost efficient. The main enabling technologies are the application of advanced high performance materials as well as cost effective manufacture processes. This paper presents the status and main results of a joint industrial research & development effort to demonstrate TRL 6 of a novel manufacturing process for large liquid propellant tanks for launcher applications. Using high strength aluminium-lithium alloy combined with the spin forming manufacturing technique, this development aims at thinner wall thickness and weight savings up to 25% as well as a significant reduction in manufacturing effort. In this program, the concave spin forming process is used to manufacture tank domes from a single flat plate. Applied to aluminium alloy, this process allows reaching the highest possible material strength status T8, eliminating numerous welding steps which are typically necessary to assemble tank domes from 3D-curved panels. To minimize raw material costs for large diameter tank domes for launchers, the dome blank has been composed from standard plates welded together prior to spin forming by friction stir welding. After welding, the dome blank is contoured in order to meet the required wall thickness distribution. For achieving a material state of T8, also in the welding seams, the applied spin forming process allows the required cold stretching of the 3D-curved dome, with a subsequent ageing in a furnace. This combined manufacturing process has been demonstrated up to TRL 6 for tank domes with a 5.4 m diameter. In this paper, the manufacturing process as well as test results are presented. Plans are shown how this process could be applied to future heavy-lift launch vehicles developments, also for larger dome diameters.

Stachulla, M.↗

NASA NTRS1974

Effect of canard location and size on canard-wing interference and aerodynamic center shift related to maneuvering aircraft at transonic speeds

A generalized wind-tunnel model, typical of highly maneuverable aircraft, was tested in the Langley 8-foot transonic pressure tunnel at Mach numbers from 0.70 to 1.20 to determine the effects of canard location and size on canard-wing interference effects and aerodynamic center shift at transonic speeds. The canards had exposed areas of 16.0 and 28.0 percent of the wing reference area and were located in the chord plane of the wing or in a position 18.5 percent of the wing mean geometric chord above or below the wing chord plane. Two different wing planforms were tested, one with leading-edge sweep of 60 deg and the other 44 deg; both wings had the same reference area and span. The results indicated that the largest benefits in lift and drag were obtained with the canard above the wing chord plane for both wings tested. The low canard configuration for the 60 deg swept wing proved to be more stable and produced a more linear pitching-moment curve than the high and coplanar canard configurations for the subsonic test Mach numbers.

Gloss, B. B.↗

DOE OSTI2022

HLPW-4/GMGW-3: High Order Discretization Technology Focus Group Workshop Summary

This paper summarizes the High-Order Technical Focus Group (HO-TFG) submissions for the joint 4th AIAA High Lift Prediction and 3rd Geometry and Mesh Generation Workshop. The goal of the workshop was to assess the state-of-the-art in mesh generation and computational fluid dynamics software. The Common Research Model High-Lift (CRM-HL) variant served as the primary focus of the workshop, and a 2D airfoil section from the CRM-HL was used as a verification test case. The HO-TFG was tasked with generating high-order curved meshes for both geometries, and computing high-order solutions using both Reynolds Averaged Navier-Stokes and scale resolving formulations. While limited by computational resources, the final results demonstrate the potential of higher-order methods to increase solution accuracy with a lower degree of freedom count relative to second-order discretizations.

Galbraith, Marshall C.↗

DOE OSTI2019

Efficient Operator-Coarsening Multigrid Schemes for Local Discontinuous Galerkin Methods

An efficient hp-multigrid scheme is presented for local discontinuous Galerkin (LDG) discretizations of elliptic problems, formulated around the idea of separately coarsening the underlying discrete gradient and divergence operators. We show that traditional multigrid coarsening of the primal formulation leads to poor and suboptimal multigrid performance, whereas coarsening of the flux formulation leads to essentially optimal convergence and is equivalent to a purely geometric multigrid method. The resulting operator-coarsening schemes do not require the entire mesh hierarchy to be explicitly built, thereby obviating the need to compute quadrature rules, lifting operators, and other mesh-related quantities on coarse meshes. We show that good multigrid convergence rates are achieved in a variety of numerical tests on two-dimensional and three-dimensional uniform and adaptive Cartesian grids, as well as for curved domains using implicitly defined meshes and for multiphase elliptic interface problems with complex geometry. Extensions, e.g., to non-LDG discretizations and fully unstructured meshes, are briefly discussed.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1973

Point and path performance of light aircraft: A review and analysis

The literature on methods for predicting the performance of light aircraft is reviewed. The methods discussed in the review extend from the classical instantaneous maximum or minimum technique to techniques for generating mathematically optimum flight paths. Classical point performance techniques are shown to be adequate in many cases but their accuracies are compromised by the need to use simple lift, drag, and thrust relations in order to get closed form solutions. Also the investigation of the effect of changes in weight, altitude, configuration, etc. involves many essentially repetitive calculations. Accordingly, computer programs are provided which can fit arbitrary drag polars and power curves with very high precision and which can then use the resulting fits to compute the performance under the assumption that the aircraft is not accelerating.

Smetana, F. O.↗

NASA NTRS1975

Interim prediction method for externally blown flap noise

An interim procedure for predicting externally blown flap (EBF) noise spectra anywhere below a powered lift aircraft is presented. Both engine-under-the-wing and engine-over-the-wing EBF systems are included. The method uses data correlations for the overall sound pressure level based on nozzle exit area and exhaust velocity along with OASPL directivity curves and normalized one-third-octave spectra. Aircraft motion effects are included by taking into account the relative motion of the source with respect to the observer and the relative velocity effects on source strength.

Dorsch, R. G.↗

NASA NTRS1986

High speed viscous flow calculations about complex configurations

Applications of the NASA Ames Parabolized Navier-Stokes (PNS) code to a variety of complex generic configurations is presented. The algorithm, boundary conditions, initial conditions, and grid generators are discussed as applied to these configurations. The PNS code was used as the mainline procedure to numerically simulate the viscous supersonic flow over these generic configurations. The turbulence model that was used in this study is the Baldwin-Lomax model. The boundary conditions are the usual viscous no slip at the wall, and a characteristic procedure is used to fit the bow shock wave which is the outermost boundary. An elliptic grid generator is employed to discretize the flow domain. In addition, an equilibrium air capability has been incorporated into the code. It uses the curve fits of Tannehill, et al. The flow regimes vary from a Mach number of 2 up to 25. Both laminar and turbulent flow are considered. Varying angles of attack have also been computed. Configurations vary from simple cone-type bodies to lifting winged bodies, such as the space shuttle or the generic supersonic cruise fighter.

Chaussee, D. S.↗

DOE OSTI2023

HLPW-4/GMGW-3: High-Order Discretization Technology Focus Group Workshop Summary

This paper summarizes the High-Order Technical Focus Group (HO-TFG) submissions for the joint 4th AIAA High Lift Prediction (HLPW-4) and 3rd Geometry and Mesh Generation Workshop (GMGW-3). The goal of the workshop was to assess the state-of-the-art in mesh generation and computational fluid dynamics software. The Common Research Model High-Lift (CRM-HL) variant served as the primary focus of the workshop, and a two-dimensional airfoil section from the CRM-HL was used as a verification test case. Here, the HO-TFG was tasked with generating high-order curved meshes for both geometries, and computing high-order solutions using both Reynolds-averaged Navier–Stokes and scale-resolving formulations. While limited by computational resources, the final results demonstrate the potential of higher-order methods to increase solution accuracy with a lower degree-of-freedom count relative to second-order discretizations.

42 ENGINEERING↗