Search NASA⌕ Search

SEARCH · Search NASA

Results for “LITHIUM FLUORIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Removal of Surface Carbonate from Lithium-Ion Battery Cathode Materials via Vapor-Phase Fluorination

Herein, ultrathin metal-fluoride barrier coatings on the surface of lithium-ion battery (LIB) cathodes can improve cycling stability and prevent corrosion by acidic byproducts in the electrolyte. Atomic layer deposition (ALD) is an effective method to deposit ultrathin metal fluoride coatings on LIB cathodes. Although numerous studies have demonstrated the benefit of ALD metal fluoride coatings to LIB performance, comparatively few works have examined the effect of individual ALD precursors on the cathode surface. This paper uses X-ray photoelectron spectroscopy (XPS) measurements to elucidate the surface chemical changes on LIB cathode material surfaces upon exposure to the ALD metal fluoride precursor, hydrogen fluorine pyridine (HFPy). We found a decrease in surface carbonate and an increase in surface fluoride after HFPy exposure suggesting the conversion of lithium carbonate (Li 2 CO 3 ) to lithium fluoride (LiF). This conversion is desirable given that Li 2 CO 3 degrades LIB performance, whereas LiF provides an excellent physio-chemical barrier against chemical attack during cycling. Scanning transmission electron microscopy, X-ray energy dispersive spectroscopy, and XPS measurements following HFPy exposure to Li 2 CO 3 powder revealed the formation of a conformal LiF shell around the Li 2 CO 3 particles. Finally, we confirmed the complete conversion of similar to 7 nm ALD Li 2 CO 3 films on silicon from HFPy exposure using XPS and spectroscopic ellipsometry. The elimination of problematic Li 2 CO 3 from LIB cathode surfaces and conversion into a protective LiF coating via a single precursor vapor treatment may provide a cost-effective method for enhancing LIB performance.

25 ENERGY STORAGE↗
DOE OSTI2023

A fluorinated cation introduces new interphasial chemistries to enable high-voltage lithium metal batteries

Abstract Fluorides have been identified as a key ingredient in interphases supporting aggressive battery chemistries. While the precursor for these fluorides must be pre-stored in electrolyte components and only delivered at extreme potentials, the chemical source of fluorine so far has been confined to either negatively-charge anions or fluorinated molecules, whose presence in the inner-Helmholtz layer of electrodes, and consequently their contribution to the interphasial chemistry, is restricted. To pre-store fluorine source on positive-charged species, here we show a cation that carries fluorine in its structure is synthesized and its contribution to interphasial chemistry is explored for the very first time. An electrolyte carrying fluorine in both cation and anion brings unprecedented interphasial chemistries that translate into superior battery performance of a lithium-metal battery, including high Coulombic efficiency of up to 99.98%, and Li 0 -dendrite prevention for 900 hours. The significance of this fluorinated cation undoubtedly extends to other advanced battery systems beyond lithium, all of which universally require kinetic protection of highly fluorinated interphases.

25 ENERGY STORAGE↗
DOE OSTI2022

Application of GO anchored mediator in a polymer electrolyte membrane for high-rate solid-state supercapacitors

Here, we synthesized a novel polymer electrolyte membrane by combining poly (vinylidene fluoride) (PVDF) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) with graphene oxide (GO) nanosheets and a lithium salt of tungstosilicic acid (Li 4 SiW 12 O 40 , hereafter, referred to SiWLi). The impact of the addition of GO/SiWLi on the microstructure and morphology of the membrane were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). We found that adding the GO/SiWLi to the PVDF/LiTFSI polymer electrolyte membrane significantly reduced the pore size. Furthermore, the addition of the GO/SiWLi resulted in not only an increase of the ionic conductivity from 0.87 $\times$ 10 –2 to 3.12 $\times$ 10 –2 Scm –1 but also an increase in the lithium-ion transference number from 0.52 to 0.87. The polymer electrolyte membranes with and without GO/SiWLi were utilized to fabricate solid-state supercapacitors. The supercapacitors fabricated with the membrane containing GO/SiWLi displayed 37.2% lower equivalent series resistance and 88.2% greater specific capacitance than those fabricated using the membrane without GO/SiWLi at 200mVs –1 .

42 ENGINEERING↗
DOE OSTI2022

The Role of Electrolyte Composition in Enabling Li Metal‐Iron Fluoride Full‐Cell Batteries

Abstract FeF 3 conversion cathodes, paired with Li metal, are promising for use in next‐generation secondary batteries and offer a remarkable theoretical energy density of 1947 Wh kg −1 compared to 690 Wh kg −1 for LiNi 0.5 Mn 1.5 O 4 ; however, many successful studies on FeF 3 cathodes are performed in cells with a large (>90‐fold) excess of Li that disguises the effects of tested variables on the anode and decreases the practical energy density of the battery. Herein, it is demonstrated that for full‐cell compatibility, the electrolyte must produce both a protective solid‐electrolyte interphase and cathode‐electrolyte interphase and that an electrolyte composed of 1:1.3:3 (m/m) LiFSI, 1,2‐dimethoxyethane, and 1,1,2,2‐tetrafluoroethyl‐2,2,3,3‐tetrafluoropropyl ether fulfills both these requirements. This work demonstrates the importance of verifying electrode level solutions on the full‐cell level when developing new battery chemistries and represents the first full cell demonstration of a Li/FeF 3 cell, with both limited Li and high capacity FeF 3 utilization.

25 ENERGY STORAGE↗
DOE OSTI2020

Li 5 VF 4 (SO 4 ) 2 : A Prototype High-Voltage Li-Ion Cathode.

A Li-rich polyanionic compound based on V 3+ with a previously unknown structure, Li 5 VF 4 (SO 4 ) 2 , has been developed as a high-voltage cathode material for Li-ion batteries. The solvothermal preparation of this material, crystal structure solution, and initial electrochemical characterization are presented. An analysis based on density functional theory electronic structure calculations suggests that a high voltage close to 5 V is required to extract two Li ions and to reach the oxidation state of V 5+ . However, the use of conventional carbonate-based electrolytes, which exhibit increasing degradation above a potential of 4.3 V, does not permit the full capacity of this compound to be achieved at this time.

25 ENERGY STORAGE↗
DOE OSTI2022

Grand challenges and opportunities in next-generation batteries and technologies

The development of advanced Li-ion batteries and technologies generally addresses one of four objectives: 1) create a higher volumetric energy density and/or specific energy/power, 2) impart intrinsically safer chemistry, 3) produce speedier charging, and 4) utilize less expensive batteries but with competitive/near-competitive performances. Certainly, other factors can play a role as well, dependent on the type of market targeted and the availability of global supplies; however, for widespread adoption, the above points/criteria remain salient. Li-ion is commercially well entrenched in industry for communication and transportation (EV) applications. Nowadays, slight iterations, mostly electrolyte-defined, are incrementally improving safety, cost, and cycle or calendar life. The last point, calendar life, is one that is often overlooked for very high-energy dense Li-ion batteries, because of their reactivity at higher charge (OCV conditions) and elevated temperatures. While cycle life is debated with respect to capacity/energy performance decline, attempts to re-purpose the battery itself or recycle the internal chemical constituents at end of life have considerably grown in the field. Hopefully, energy-neutral processes are also considered in the recycling loop. Nevertheless, the energy storage arena is quite large, and this pursuit hinges on pushing the field in one of many directions, toward loftier objectives. The pursuit of next-generation batteries and technologies must thus delve deeper into new and novel chemistry and electrochemistry to create a world with a neutral, carbon-free environment, and one that is solely sufficient on energy-producing renewables such as the Sun and wind-derived means. The application of electricity and chemistry within our world is thus a 21st century opus.

25 ENERGY STORAGE↗
DOE OSTI2020

Fabrication and Characterization of Composite Membranes for the Concentration of Lithium Containing Solutions Using Forward Osmosis

In this study, an energy and highly time efficient, cost effective, and scalable forward osmosis (FO) composite polyvinylidene fluoride (PVDF) membrane is developed to concentrate lithium chloride recovered from naturally occurring geothermal brine resources. Dense thin robust defect-free Kynar-PVDF membranes are fabricated on porous PVDF hollow fiber supports. Various membrane fabrication parameters such as membrane thickness, coating solution concentration, cross-linker concentration, and curing temperature are studied to develop a defect-free dense membrane. Advanced characterization tools such as FIB-SEM, Raman, FTIR spectroscopy, and XRD are used to study the surface and cross-sectional morphology, chemistry of crosslinking, crystallinity and chemical structure of the dense PVDF membrane. FO is utilized to concentrate LiCl in the solution from 36 to 175 g L -1 with an average water transfer rate of 0.450 L m -2 h -1 (LMH) at 85 °C. Furthermore, the membrane showed stable performance for more than 550 h while maintaining the purity of the concentrated lithium chloride solution of >99.99 wt%. Overall, the results suggest that the FO-based technology is an innovative, time and energy efficient approach compared to the conventional technologies for concentration of battery grade LiCl for application in lithium ion batteries and other clean energy technologies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Effects of water-based binders on electrochemical performance of manganese dioxide cathode in mild aqueous zinc batteries

In the majority of rechargeable batteries including lithium ion batteries (LIBs), polyvinylidene fluoride (PVdF) binders are the most commonly used binder for both anode and cathode. However, using PVdF binder requires the organic solvent of N-methyl-2-pyrrolidone (NMP) which is expensive, volatile, combustible, toxic, and has poor recyclability. Therefore, switching to aqueous electrode processing routes with non-toxic binders would provide a great leap forward towards the realization of ideally fully sustainable and environmentally friendly electrochemical energy storage devices. Various water-soluble binders (aqueous binders) were characterized and compared to the performance of conventional PVDF. Our study demonstrates that the electrochemical performance of Zn/MnO2 aqueous batteries is significantly improved by using sodium carboxymethyl cellulose (CMC) binder. Additionally, CMC binders offers desirable adhesion, good wettability, homogeneous material distribution, and strong chemical stability at certain pH levels (3.5~5) without any decomposition for long-cycle life.

25 ENERGY STORAGE↗
NASA NTRS1969

High-energy, high-power, long-life battery

High-energy-density primary battery achieves energy densities of up to 130 watt hrs./lb. The electrochemical couple consists of a lithium anode, a copper-fluoride cathode, and uses methyl formate/lithium hexafluoroarsenate for the electrolyte. Once achieved, battery life is approximately 30 hours.

Abens, S. G.↗
DOE OSTI2020

A polymeric composite protective layer for stable Li metal anodes

Lithium (Li) metal is a promising anode for high-performance secondary lithium batteries with high energy density due to its highest theoretical specific capacity and lowest electrochemical potential among anode materials. However, the dendritic growth and detrimental reactions with electrolyte during Li plating raise safety concerns and lead to premature failure. Herein, we report that a homogeneous nanocomposite protective layer, prepared by uniformly dispersing AlPO 4 nanoparticles into the vinylidene fluoride-co-hexafluoropropylene matrix, can effectively prevent dendrite growth and lead to superior cycling performance due to synergistic influence of homogeneous Li plating and electronic insulation of polymeric layer. The results reveal that the protected Li anode is able to sustain repeated Li plating/stripping for >750 cycles under a high current density of 3 mA cm -2 and under a practical specific capacity of 2 mAh cm -2 . Moreover, full-cell Li-ion battery is constructed by using LiFePO 4 and protected Li as a cathode and anode, respectively, rendering a stable capacity after 400 charge/discharge cycles. The current work presents a promising approach to stabilize Li metal anodes for next-generation Li secondary batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Synthesis of Fluorine-Doped Lithium Argyrodite Solid Electrolytes for Solid-State Lithium Metal Batteries

Solid-state lithium metal batteries (SSLMBs) that utilize novel solid electrolytes (SEs) have garnered much attention because of their potential to yield safe and high-energy-density batteries. Sulfide-based argyrodite-class SEs are an attractive option because of their impressive ionic conductivity. Recent studies have shown that LiF at the interface between Li and SE enhances electrochemical stability. However, the synthesis of F-doped argyrodites has remained challenging because of the high temperatures used in the state-of-the-art solid-state synthesis methods. In this work, for the f irst time, we report F-doped Li 5+y PS 5 F y argyrodites with a tunable doping content and dual dopants (F-/Cl- and F-/Br-) that were synthesized through a solvent-based approach. Among all compositions, Li 6 PS 5 F 0.5 C l0.5 exhibits the highest Li-ion conductivity of 3.5 x 10 -4 S cm -1 at room temperature (RT). Furthermore, Li symmetric cells using Li 6 PS 5 F 0.5 Cl 0.5 show the best cycling performance among the tested cells. X-ray photoelectron spectroscopy and ab initio molecular dynamics simulations revealed that the enhanced interfacial stability of Li 6 PS 5 F 0.5 C l0.5 SE against Li metal can be attributed to the formation of a stable solid electrolyte interphase (SEI)-containing conductive species (Li 3 P), alongside LiCl and LiF. These findings open new opportunities to develop high-performance SSLMBs using a novel class of F-doped argyrodite electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2021

Edge-Propagation Discharge Mechanism in CFx Batteries—A First-Principles and Experimental Study

Graphite fluoride (CF x ) cathodes coupled with lithium anodes yield one of the highest theoretical specific capacities (>860 mAh/g) among primary batteries. In practice, the observed discharge voltage (~2.5 V) is significantly lower than thermodynamic limits (>4.5 V), the discharge rate is low, and so far Li/CF x has only been used in primary batteries. Understanding the discharge mechanism at atomic length scales will improve practical CFx energy density, rate capability, and rechargeability. So far, purely experimental techniques have not identified the correct discharge mechanism or explained the discharge voltage. In this work, we apply density functional theory calculations to demonstrate that a CF x -edge propagation discharge mechanism based on lithium insertion at the CF/C boundary in partially discharged CF x exhibits a voltage range of 2.5 to 2.9 V—depending on whether solvent molecules are involved. The voltages and solvent dependence agree with our discharge and galvanostatic intermittent titration technique measurements. The predicted discharge kinetics are consistent with CF x operations. Finally, we predict some Li/CF x rechargeability under the application of high potentials, along a charging pathway different from that of discharge. Our work represents a general, quasi-kinetic framework to understand the discharge of conversion cathodes, circumventing the widely used phase diagram approach which most likely does not apply to Li/CF x because equilibrium conditions are not attained in this system.

25 ENERGY STORAGE↗
DOE OSTI2025

Species Transport Framework Development in SAM for System-Level Tritium Source Term Analysis

The SAM code is under development as a modern system-level modeling and simulation tool for advanced non–light water reactor safety analyses, with recent efforts to add capabilities to evaluate radiological source term risks in these novel reactor concepts. By leveraging the established system-level multiphysics thermal-hydraulic models in SAM, a framework for tightly coupled species transport modeling has been integrated into the code for engineering-scale source term evaluation. This species transport framework was first applied to the simulation of tritium, which is a well-known source term in conventional light water reactors. Tritium poses a unique risk in salt-cooled reactors, especially those with lithium-bearing salts such as the fluoride salt–cooled high-temperature reactor (FHR) concept, as tritium is generated in the salt coolant in significant quantities due to neutron interactions. A compounding factor is the increased mobility of tritium at high temperatures, which is able to permeate through metals while also potentially being retained in graphite pebbles and structures. Engineering-scale models for the tritium transport pathways in a FHR have been developed using the new species transport framework in SAM. The capabilities are assessed through analytical verification problems and validated with data from a graphite retention experiment. In conclusion, the system-level model is demonstrated by performing an initial estimate of baseline tritium generation and flows in a generic reference SAM FHR model, setting a foundation for future studies of source term transient analysis with the potential for further multiscale and multiphysics integration.

SAM↗
DOE OSTI2025

Computational Fluid Dynamics Analysis of the Molten Salt Tritium Transport Experiment Test Section

Tritium, a radionuclide produced through neutron capture by lithium and other elements (beryllium and fluoride) in molten salts, presents unique challenges to radionuclide release. This is true for both fusion energy breeder blankets and molten salt fission reactors. The fundamental understanding of tritium transport is crucial to the safe design and operation of these reactors. The Molten Salt Tritium Transport Experiment (MSTTE), currently under construction at Idaho National Laboratory, aims to investigate tritium transport phenomena using a forced-convection fluoride salt loop. This loop is designed to study various transport mechanisms, such as permeation through metals and gas-liquid interactions, and is intended to support future research on tritium extraction units. A critical aspect of the MSTTE loop design is ensuring a fully developed velocity profile before the fluid reaches the permeation test section where measurements are made. This study employs computational fluid dynamics to model the salt flow behavior within the MSTTE permeation test section. A realizable k-ε turbulent model with enhanced wall treatment is used to simulate the single-phase, vertical upward flow of molten salt FLiNaK under isothermal conditions. The simulation results indicated flow distortion and underdeveloped profiles at all planned flow rates within the test section due to the 85-deg sharp bend. To address this issue, a reduced diameter with a reducer and expander and a flow conditioner are investigated to achieve fully developed flow. The analysis showed that the flow conditioner successfully corrected the flow profile, achieving fully developed behavior at a flow rate of 50 liters per minute (LPM). In conclusion, this research enhances our understanding of flow dynamics in molten salt systems and contributes to optimizing tritium transport control technologies.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Influence of Binder Coverage on Interfacial Chemistry of Thin Film LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathodes

In this work, we explore the influence of binder coverage and chemistry on the interfacial properties of the textured Ni-rich cathode LiNi 0.6 Mn 0.2 Co 0.2 O 2 . We find that the formation of the cathode/electrolyte interphase (CEI) composition varies significantly for cathodes coated with either poly(vinylene fluoride) (PVDF), carboxymethyl cellulose (CMC), or lithium polyacrylate (LiPAA) after cycling to high upper cutoff voltages (4.5 V vs Li/Li). The PVDF-coated samples had a thinner CEI and twice the relative concentration of LiF and Li 2 CO 3 to Li x PO y F z species in the CEI compared to the uncoated sample. This correlated with significantly lower interfacial impedance (285 vs ~1700 Ohm-cm 2 ) and improved capacity retention between cycles of the PVDF-coated samples compared to the other binder compositions and the uncoated sample. CMC-coated samples performed worst, with a CEI comprised of greater amounts of Li x PO y F z . In addition, we find the choice of binder results in the selective protection or promotion of electrolyte reactions at the (104) surface of the 622 cathode. This suggests that the choice of binder can impact the surface chemistry and performance of high voltage cathodes and supports an avenue for interest in multifunctional binders for stabilizing the CEI.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2002

Contactless conductivity detector for microchip capillary electrophoresis

A microfabricated electrophoresis chip with an integrated contactless conductivity detection system is described. The new contactless conductivity microchip detector is based on placing two planar sensing aluminum film electrodes on the outer side of a poly(methyl methacrylate) (PMMA) microchip (without contacting the solution) and measuring the impedance of the solution in the separation channel. The contactless route obviates problems (e.g., fouling, unwanted reactions) associated with the electrode-solution contact, offers isolation of the detection system from high separation fields, does not compromise the separation efficiency, and greatly simplifies the detector fabrication. Relevant experimental variables, such as the frequency and amplitude of the applied ac voltage or the separation voltage, were examined and optimized. The detector performance was illustrated by the separation of potassium, sodium, barium, and lithium cations and the chloride, sulfate, fluoride, acetate, and phosphate anions. The response was linear (over the 20 microM-7 mM range) and reproducible (RSD = 3.4-4.9%; n = 10), with detection limits of 2.8 and 6.4 microM (for potassium and chloride, respectively). The advantages associated with the contactless conductivity detection, along with the low cost of the integrated PMMA chip/detection system, should enhance the power and scope of microfluidic analytical devices.

NASA Center JPL↗
NASA NTRS1996

Neutron fluences and dose equivalents measured with passive detectors on LDEF

Neutron fluences were measured on LDEF in the low energy (< 1 MeV) and high energy (> 1 MeV) ranges. The low energy detectors used the 6Li(n,alpha)T reaction with Gd foil absorbers to separate thermal (< 0.2 eV) and resonance (0.2 eV-1 MeV) neutron response. High energy detectors contained sets of fission foils (181Ta, 209Bi, 232Th, 238U) with different neutron energy thresholds. The measured neutron fluences together with predicted spectral shapes were used to estimate neutron dose equivalents. The detectors were located in the A0015 and P0006 experiments at the west and Earth sides of LDEF under shielding varying from 1 to 19 g/cm2. Dose equivalent rates varied from 0.8 to 3.3 microSv/d for the low energy neutrons and from 160 to 390 microSv/d for the high energy neutrons. This compares with TLD measured absorbed dose rates in the range of 1000-3000 microGy/d near these locations and demonstrates that high energy neutrons contribute a significant fraction of the total dose equivalent in LEO. Comparisons between measurements and calculations were made for high energy neutrons based on fission fragment tracks generated by fission foils at different shielding depths. A simple 1-D slab geometry was used in the calculations. Agreement between measurements and calculations depended on both shielding depth and threshold energy of the fission foils. Differences increased as both shielding and threshold energy increased. The modeled proton/neutron spectra appeared deficient at high energies. A 3-D model of the experiments is needed to help resolve the differences.

LDEF Project↗