Search NASA⌕ Search

SEARCH · Search NASA

Results for “Large Plasma Device”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Active Divertor Heat Flux Control using Impurity Powder Dropper

Divertor plasma-facing components (PFCs) in a tokamak are typically designed to withstand average steady-state heat loads of about 5–10 MW/m 2 , a limit that applies to both solid and liquid lithium (LL) PFCs. Exceeding these design values can result in surface damage to tungsten PFCs or excessive lithium (Li) evaporation in liquid lithium divertor (LLD) PFCs. Since exceeding the divertor heat load limits has serious consequences, it is therefore prudent to develop a tool to reduce the divertor heat load and bring the heat load to within the design limit without affecting the plasma performance. Active low Z impurity injection such as Li has been suggested as a potential solution to mitigate excess heat flux as suggested previously, given that non-coronal radiation can be quite large ~ 20–30 MJ per mole of injected Li. Li is considered desirable for reducing the edge neutral recycling helping to improve plasma energy confinement. In this paper, we model the Impurity Power Dropper (IPD) to investigate its potential of divertor heat flux control. The IPD is typically located at the top of the tokamak device and uses a vertical drift tube of a few meters. In the 2 m drift tube case, the IPD powder is accelerated to ~ 6 m/sec before reaching the plasma with the upper divertor configuration, matching the condition for the in-board side pellet injection case. By modeling the IPD geometry we determined the IPD powder deposition profile, and thus the non-coronal radiation and ionization profiles in time as well. From the enhanced radiation power loss, it is therefore possible to reduce the divertor heat load using the divertor simulation code. In conclusion, the IPD divertor heat flux control can be tested in the facilities with IPD including ST-40, DIII-D, EAST, WEST and NSTX-U.

Active lithium injection↗
DOE OSTI2022

External charge compensation in etched gallium nitride measured by x-ray photoelectron spectroscopy

Electronic states at GaN surfaces and at regrowth and heteroepitaxy interfaces inhibit electronic device performance. Understanding electronic state configuration at the GaN surface is, therefore, crucial for the development of GaN-based devices, which are currently of considerable interest in power electronic applications. GaN and other wurtzite III-nitrides possess large spontaneous polarization along the c-axis, producing a bound sheet charge at the surface, which affects the electronic state configuration through the formation of internal and external compensation charges. Defects induced by conventional plasma-based dry etching methods may inhibit the internal screening of this bound charge and thus increase the concentration of external charged states. The surface band bending of n-type Ga-face GaN (0001) was measured with x-ray photoelectron spectroscopy after inductively coupled plasma etching to investigate the impact of dry etching on external charge compensation. GaN samples were etched using inductively coupled plasma with varying rf power and a novel plasma-enhanced atomic layer etching method using an oxidation, fluorination, and ligand-exchange mechanism. The band bending varied from 0.0 to 0.8 ± 0.1 eV for the samples measured.

Hatch, Kevin A. (ORCID:0000000283118623)↗
DOE OSTI2020

Creation and sustainment of wide pedestal quiescent H-mode with zero net neutral beam torque

Recent experiments on DIII-D have shown it is possible to create and sustain wide pedestal quiescent H-mode (QH-mode) plasmas with zero net torque from neutral beam injection (NBI) for the full discharge duration. Wide pedestal QH-mode has many of the features of the previously investigated QH-mode while having the advantage of increased edge pedestal pressure and excellent energy confinement time. Both QH-mode variants operate without edge localized modes. Accordingly, these discharges demonstrate that significant input torque is not essential to the exploitation of wide pedestal QH-mode in future devices that are expected to have small or nonexistent NBI torque. In conclusion, developing operating conditions that allowed net zero torque access to wide pedestal QH-mode required implementing several techniques to avoid locked modes including minimizing intrinsic error fields, avoiding large sawteeth, and driving toroidal rotation via neoclassical toroidal viscosity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Fiber-Optic Silicon Fabry-Perot Interferometric Bolometer: The Influence of Mechanical Vibration and Magnetic Field

Plasma radiation plays an important role in the operation and control of magnetic confinement fusion and is typically measured by bolometers. Here, we study the influence of mechanical vibration and magnetic field, which are typically present in magnetic confinement fusion devices, on the performance of a fiber-optic bolometer (FOB) based on silicon Fabry-Perot interferometer (FPI) demodulated by a scanning diode laser. It is found that both the vibration and magnetic field could cause large noise due to the birefringence of the silicon FPI. To mitigate the birefringence effects, we demonstrated two effective methods: polarization maintaining FOB and polarization scrambling. We show that two methods can be effective in mitigating the effect caused by the sensor birefringence: (1) replacing the regular single-mode fiber in the FOB system with polarization-maintaining fiber and (2) using a polarization scrambler after the laser source. For both methods, no significant increase in the noise was observed in the vibration and magnetic field tests. Finally, our research highlights the importance of the polarization management for the FOB systems toward their practical applications in magnetic-confinement fusion systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Towards Predictive Plasma Science and Engineering through Revolutionary Multi-Scale Algorithms and Models (Final Report)

This report describes the high-level accomplishments from the Plasma Science and Engineering Grand Challenge LDRD at Sandia National Laboratories. The Laboratory has a need to demonstrate predictive capabilities to model plasma phenomena in order to rapidly accelerate engineering development in several mission areas. The purpose of this Grand Challenge LDRD was to advance the fundamental models, methods, and algorithms along with supporting electrode science foundation to enable a revolutionary shift towards predictive plasma engineering design principles. This project integrated the SNL knowledge base in computer science, plasma physics, materials science, applied mathematics, and relevant application engineering to establish new cross-laboratory collaborations on these topics. As an initial exemplar, this project focused efforts on improving multi-scale modeling capabilities that are utilized to predict the electrical power delivery on large-scale pulsed power accelerators. Specifically, this LDRD was structured into three primary research thrusts that, when integrated, enable complex simulations of these devices: (1) the exploration of multi-scale models describing the desorption of contaminants from pulsed power electrodes, (2) the development of improved algorithms and code technologies to treat the multi-physics phenomena required to predict device performance, and (3) the creation of a rigorous verification and validation infrastructure to evaluate the codes and models across a range of challenge problems. These components were integrated into initial demonstrations of the largest simulations of multi-level vacuum power flow completed to-date, executed on the leading HPC computing machines available in the NNSA complex today. These preliminary studies indicate relevant pulsed power engineering design simulations can now be completed in (of order) several days, a significant improvement over pre-LDRD levels of performance.

42 ENGINEERING↗
DOE OSTI2024

Plasma self-driven current in tokamaks with magnetic islands

Magnetic island perturbations may cause a reduction in plasma self-driven current that is needed for tokamak operation. A novel effect on tokamak self-driven current revealed by global gyrokinetic simulations is due to magnetic-island-induced 3D electric potential structures, which have the same dominant mode numbers as that of the magnetic island, whereas centered at both the inner and outer edge of the island. The non-resonant potential islands are shown to drive a current through an efficient nonlinear parallel acceleration of electrons. In large aspect ratio (large-A) tokamak devices, this new effect can result in a significant global reduction of the electron bootstrap current when the island size is sufficiently large, in addition to the local current loss across the island region due to the pressure profile flattening. It is shown that there exists a critical magnetic island width for large-A tokamaks beyond which the electron bootstrap current loss is global and increases rapidly with the island size. As such, this process may introduce a size limit for tolerable magnetic islands in large-A tokamak devices in the context of steady state operation. On the other hand, the current loss caused by magnetic islands in low-A tokamaks such as spherical tokamak (ST) NSTX/U is minor. The reduction of the axisymmetric current by magnetic islands scales with the square of island width. However, the loss of the current is mainly local to the island region, and the pace of current loss as the island size increases is substantially slower compared to large-A tokamaks. In particular, the bootstrap current reduction in STs is even smaller in the reactor-relevant high-β p regime where neoclassical tearing modes are more likely to develop.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Multimodal Prediction of Tearing Instabilities in a Tokamak

Tokamak is a torus-shaped nuclear fusion device that uses magnetic fields to confine fusion fuel in the form of plasma. Tearing instability in plasma is a major issue in which the magnetic field breaks and recombines in tokamak. Here, this instability can lead to plasma disruption that terminates the fusion power generation and damages the plasma-facing wall materials. For a successful steady operation of a large-scale tokamak without disruption, it is required to predict and alarm the tearing instabilities well in advance to avoid them. In this work, we develop and validate a deep neural network-based multimodal prediction system that estimates the future tearing instability likelihood from multi-diagnostics signals in the DIII-D tokamak.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Final Design and Analysis of the Superconducting Magnets for the Material Plasma Exposure Experiment

The Material Plasma Exposure eXperiment (MPEX), which has completed its final design, is a new linear plasma device to advance the understanding of plasma-material interactions through the generation and delivery of plasmas as they are expected in future fusion reactor divertors. MPEX will be a steady-state device to study high-fluence exposures of plasma-facing materials and components. The requirements for the magnetic field at the heating stages and the target make the application of superconducting coils necessary. The final designs for the superconducting magnets have been developed using three cryostat designs with warm bore diameters of 65 cm and 156 cm. The large bores are required to for other systems such as vacuum, water cooling, and RF power. There are 19 superconducting coils in MPEX that are contained in six cryostats. Although design, fabrication, and testing for the magnets as stand-alone units are straightforward, challenges will arise during the integration of the system. Various field profiles will be used during operation. The magnetic field where the electron cyclotron heating occurs needs to operate at both 1.25 and 2.50 T. Analyses that have been performed on the final design include designing the coils and determining operating currents to meet field requirements, forces between cryostats, the effects of coil and/or cryostat movement, and quench analysis. To ensure that the magnetic field requirements are met, a plan for monitoring the magnetic field at specified locations has been developed which includes the effect of coil and/or cryostat movement.

Burkhardt, Earle↗
DOE OSTI2020

A new frontier in laboratory physics: magnetized electron–positron plasmas

We describe here efforts to create and study magnetized electron–positron pair plasmas, the existence of which in astrophysical environments is well-established. Laboratory incarnations of such systems are becoming ever more possible due to novel approaches and techniques in plasma, beam and laser physics. Traditional magnetized plasmas studied to date, both in nature and in the laboratory, exhibit a host of different wave types, many of which are generically unstable and evolve into turbulence or violent instabilities. This complexity and the instability of these waves stem to a large degree from the difference in mass between the positively and the negatively charged species: the ions and the electrons. The mass symmetry of pair plasmas, on the other hand, results in unique behaviour, a topic that has been intensively studied theoretically and numerically for decades, but experimental studies are still in the early stages of development. A levitated dipole device is now under construction to study magnetized low-energy, short-Debye-length electron–positron plasmas; this experiment, as well as a stellarator device that is in the planning stage, will be fuelled by a reactor-based positron source and make use of state-of-the-art positron cooling and storage techniques. Relativistic pair plasmas with very different parameters will be created using pair production resulting from intense laser–matter interactions and will be confined in a high-field mirror configuration. We highlight the differences between and similarities among these approaches, and discuss the unique physics insights that can be gained by these studies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Prominent radiative contributions from multiply-excited states in laser-produced tin plasma for nanolithography

Extreme ultraviolet (EUV) lithography is currently entering high-volume manufacturing to enable the continued miniaturization of semiconductor devices. The required EUV light, at 13.5 nm wavelength, is produced in a hot and dense laser-driven tin plasma. The atomic origins of this light are demonstrably poorly understood. Here we calculate detailed tin opacity spectra using the Los Alamos atomic physics suite ATOMIC and validate these calculations with experimental comparisons. Our key finding is that EUV light largely originates from transitions between multiply-excited states, and not from the singly-excited states decaying to the ground state as is the current paradigm. Moreover, we find that transitions between these multiply-excited states also contribute in the same narrow window around 13.5 nm as those originating from singly-excited states, and this striking property holds over a wide range of charge states. We thus reveal the doubly magic behavior of tin and the origins of the EUV light.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

High Performance Equilibrium Solvers for Integrated Magnetic Fusion Simulations

With the funding provided by this award, we developed numerical codes for the study of magnetically confined plasmas for fusion applications. Accordingly, our work can be divided into two separate categories: 1) the design and analysis of novel numerical methods providing high accuracy and high efficiency; 2) the study of the equilibrium and stability of magnetically confined plasmas with some of these numerical codes, as well as the study of the nature of the turbulent behavior which may arise in the presence of instabilities. We first developed new numerical schemes based on integral equation methods for the computation of steady-state magnetic configurations in fusion experiments, providing high accuracy for the magnetic field and its derivatives, which are required for stability and turbulence calculations. We employed different integral formulations depending on the application of interest: axisymmetric or non-axisymmetric equilibria, force-free or magnetohydrodynamic equilibria, fixed-boundary equilibria or free-boundary equilibria. While efficient, these methods do not yet apply to plasma boundaries which are not smooth, a situation which is fairly common in magnetic confinement experiments. To address this temporary weakness, we also constructed a new steady-state solver based on the Hybridizable Discontinuous Galerkin (HDG) method, which provides full geometric flexibility. In addition to these numerical tools focused on steady-states, we also contributed to the improvement of the speed and accuracy of codes simulating the plasma dynamics of fusion plasmas, by developing a novel velocity space representation for the efficient solution of kinetic equations, which most accurately describe the time evolution of hot plasmas in fusion experiments. Using the tools discussed above, we studied several questions pertaining to the equilibrium and stability of magnetically confined plasmas. In particular, we derived a new simple model for axisymmetric devices called tokamaks, to predict how elongated a fusion plasma can be before it becomes unstable and collapses. We also looked at the effect of the shape of the outer plasma surface on key properties of the steady-state magnetic configurations, and how these properties impact turbulence in fusion plasmas, and the corresponding transport of momentum. Likewise, we studied the role of large localized flows on the steady-state magnetic configurations, and how they may influence plasma stability and turbulence. Non-axisymmetric steady-state magnetic configurations are inherently more complex than axisymmetric steady-state configurations, and the subject of ongoing controversies regarding the regularity of the equations determining such steady-states, and their solutions. Implementing an existing NYU code in a new geometry, we studied the nature of the singularity of the solutions observed in the code, and methods to eliminate them. Our main conclusion is that by appropriately tailoring the plasma boundary, it is possible to eliminate the singularities otherwise appearing in our simulations, and to obtain steady-states which appear to be smooth. To gain further insights on incompletely understood turbulence phenomena, we proposed a new reduced model capturing most of these phenomena, which is simple enough to not require expensive numerical simulations on massive supercomputers to investigate them. We demonstrated the strong similarity between our simulations and published results obtained from computationally expensive simulations, and plan to rely on our reduced model to identify the key mechanisms determining the evolution and strength turbulent driven transport in fusion plasmas. Finally, we proposed a new framework for tokamak reactor design studies, enabling us to consider the relative merits of steady-state versus pulsed fusion reactors. We found that pulsed fusion reactors may benefit most from recent advances in magnet technology, and the availability of very high field magnets. As such, they may become more desirable than steady-state tokamak reactors for cost efficient electricity generation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Measurement of the energy distribution of electrons escaping confinement from an electron cyclotron resonance ion source

Production of high charge state ions in electron cyclotron resonance ion sources (ECRISs) is dependent on the electron energy distribution (EED) within the source plasma. In order to better understand the EED, a measurement of electrons escaping axially from an ECRIS device has been performed at the National Superconducting Cyclotron Laboratory. Electrons were measured escaping from the Superconducting Source for Ions, driven at 18 GHz. Dependencies of the observed EED on the confining magnetic field strength and injected microwave power are reported. This paper focuses on large peaks of electrons in the 400–1200 keV energy range. Measurements of the axial bremsstrahlung spectrum have been simultaneously carried out to provide a direct comparison between both techniques. A comparison between the energy associated with the peak of the electron distribution and the spectral temperature of the bremsstrahlung distribution is shown.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Design Considerations for the Implementation of a High-Field-Side Transient CHI System on QUEST

Transient coaxial helicity injection (T-CHI), a method first developed on the small helicity injected torus (HIT-II) experiment and then validated on the much larger National Spherical Torus Experiment (NSTX) device, is a method to initiate an inductive-like tokamak plasma discharge without reliance on the central solenoid. A CHI discharge is initiated by driving current along magnetic flux that connects the inner and outer divertor plates on one end of the tokamak. To permit this, on both HIT-II and NSTX, toroidal ceramic insulators were used to electrically separate the inner and outer vessel components. The use of such large toroidal vacuum insulators may not be easy to implement in reactors. To address this issue, the Q-shu University experiments with steady-state spherical tokamak (ST) (QUEST) is developing a reactor-relevant CHI configuration in which one of the divertor plates is electrically insulated from the rest of the vessel. The first application of T-CHI on QUEST biased the CHI electrode to the outer vessel. While the CHI discharges could be easily generated, it was found that as the discharge filled the vessel, the separation distance between the injector magnetic flux footprints widened, a condition that is not favorable for the generation of closed flux surfaces. Biasing the electrode to the inner wall is a configuration similar to that used on NSTX and HIT-II, but initial testing in this configuration has proved to be challenging. The design described here overcomes the present limitation by locating the CHI electrode much closer to the CHI injector flux coil and using an NSTX-like gas injection manifold to enable high-field-side T-CHI startup on QUEST. Finally, the concepts described in this article should also benefit the future implementation of T-CHI systems in other tokamaks and spherical tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Assessment of radial transport induced by Alfvénic resonances in tokamaks and stellarators

In a symmetric plasma confinement device, a perturbation such as an Alfvén mode produces a resonance island which flattens the local energy gradient due to induced rotation about the elliptic points of the resonance. The location of the resonance is mode frequency and particle energy dependent, and particles away from the resonance are not affected. Here, a projection onto the Poincaré subspace allows the evaluation of resonance widths and internal rotation rates. In a stellarator without symmetry because of the toroidal dependence of the equilibrium magnetic field, a mode instead produces chaos in all orbits passing where the amplitude is large and is, thus, much more effective in producing radial transport and loss. The mode growth rate and saturation are also affected by the local chaos.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Enhanced performance in fusion plasmas through turbulence suppression by megaelectronvolt ions

Alpha particles with energies on the order of megaelectronvolts will be the main source of plasma heating in future magnetic confinement fusion reactors. Instead of heating fuel ions, most of the energy of alpha particles is transferred to electrons in the plasma. Furthermore, alpha particles can also excite Alfvénic instabilities, which were previously considered to be detrimental to the performance of the fusion device. In this work, we report improved thermal ion confinement in the presence of megaelectronvolts ions and strong fast ion-driven Alfvénic instabilities in recent experiments on the Joint European Torus. Herein, detailed transport analysis of these experiments reveals turbulence suppression through a complex multi-scale mechanism that generates large-scale zonal flows. This holds promise for more economical operation of fusion reactors with dominant alpha particle heating and ultimately cheaper fusion electricity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Energetic particle transport and loss induced by helically-trapped energetic-ion-driven resistive interchange modes in the Large Helical Device

Here, energetic-ion confinement and loss due to energetic-ion driven magnetohydrodynamic modes are studied using comprehensive neutron diagnostics and orbit-following numerical simulations for the Large Helical Device (LHD). The neutron flux monitor is employed in order to obtain global confinement of energetic ions and two installed vertical neutron cameras (VNCs) viewing different poloidal cross-sections are utilized in order to measure the radial profile of energetic ions. A strong helically-trapped energetic-ion-driven resistive interchange mode (EIC) excited in relatively low-density plasma terminated high-temperature state in LHD. Changes in the neutron emission profile due to the EIC excitation are clearly visualized by the VNCs. The reduction in the neutron signal for the helical ripple valley increases with EIC amplitude, which reaches approximately 50%. In addition to the EIC experiment, orbit-following simulations using the DELTA5D code with EIC fluctuations were performed to assess the energetic-ion transport and loss. Two-dimensional temporal evolution results show that the neutron emissivity at the helical ripple decreases significantly due to the EIC. The rapid reduction in neutron emissivity shows that the helically-trapped beam ions immediately escape from the plasma. The reduction in the VNC signals for the helical ripple valley and the total neutron emission rate increase with increasing EIC amplitude, as observed in the experiment. Calculated line-integrated neutron emission results show that the profile measured by VNC1 has one peak, whereas the profile measured by VNC2 has two peaks, as observed in the experiment. Although the neutron emission profile for VNC2 has a relatively wide peak compared with the experimental results, the significant decrease in neutron signal corresponding to the helical ripple valley was successfully reproduced.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Alfvén mode induced particle loss in LHD

Herein losses of beam ions due to Alfvén modes are simulated for discharges in the Large Helical Device at Toki, Japan, using a guiding center code. High frequency beam particle resonances are found for the equilibria for passing particles, providing locations for the destablization of Alfvén modes observed in the device. Losses due to even small modes due to these resonances are significant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Modeling Temperature Profiles in the Pedestal of NSTX with Reduced Models

This paper describes new modeling capabilities for predicting H-mode pedestal profiles in spherical tokamaks. Temperature profiles for NSTX discharges 132543 and 132588 are modeled by coupling the \textsc{astra} transport solver with neoclassical transport and gyrokinetic-based reduced models for electron temperature gradient (ETG) and kinetic ballooning mode (KBM) instabilities. A quasi-linear surrogate model for ion-scale transport is developed using linear \textsc{gene} simulations, requiring only a single free parameter calibrated to one discharge. Time-evolving the temperatures with fixed density yields good agreement with experiments for both discharges. Systematic analysis of the transport mechanisms reveals that neoclassical transport is huge across the entire pedestal region for the ion channel. ETG turbulence is large in the plasma edge and low density gradient region, contributing substantially to the electron channel. However, KBM/MHD-like modes also drive significant transport in both the ion and electron thermal channels, making them essential for accurate pedestal modeling. Further refinements, including explicit E×B shear suppression and scaled ETG transport, produce quantitative but not qualitative improvements. This work lays the foundation for predictive modeling of future devices. This paper is on arxiv and has been submitted to Nuclear Fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗