Search NASA⌕ Search

SEARCH · Search NASA

Results for “Layer top”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Convection phenomena during the growth of sodium chlorate crystals from solution

The paper examines convection phenomena during the growth of sodium chlorate crystals from solution. Schlieren observations of sodium chlorate crystals suspended in supersaturated solutions showed that with increase in supersaturation or crystal size, the boundary layer on the side faces was stable while the top boundary layer and emerging plume changed from stable to partially oscillatory. The transition was a function of the Grashof number, Gr sub top, and the crystal height. Gr sub top correlated with plume width, number of streamlines, eddy density, and plume velocity, but the oscillation period correlated with the weight increase growth rate. The mass transfer rate, the linear growth rate, and growth of vertical and horizontal faces are discussed, and an estimate of boundary layer flow vs growth rate for near-critical stable convection indicated that growth of side faces depleted over half of the excess solute in the boundary layer. Impulse energies greatly in excess of the threshold value caused transient separation of the boundary layer on the top face, and plume wavering due to background-induced fluid motion was observed only at the lowest supersaturations.

Chen, P. S.↗
NASA NTRS1981

AlGaAs/GaAs transverse junction stripe lasers with distributed feedback

Transverse junction stripe (TJS) lasers with periodic feedback were fabricated in two geometries. An interferometric and wet chemical etching technique was used to create a feedback grating across the entire pumping region for the distributed feedback (DFB) TJS laser and to create the separate distributed Bragg reflectors/DBR) for the TJS/DBR laser. The TJS/DFB laser was a double heterostructure device grown by liquid phase epitaxy (LPE) and had a third order grating etched in the top ALO.2GaO.8As layer. The grating was buried by growing an ALO.35GaO.65As layer on the grating by metal organic chemical vapor deposition (MO-CVD). The TJS/DBR laser was also fabricated in an LPE double heterostructure. The top AlGaAs layer was thinned to 0.1 micron over more than half of the laser so that the grating would be close to the GaAs active layer and optical field. Single mode operation in both configurations was obtained. The thermal shift of the laser wavelength in both cases was less than 1 Angstrom/deg K, compared to the 3 Angstrom/deg K shift of the spontaneous emission peak.

Hafich, M. J.↗
NASA NTRS1989

Isotope exchange in oxide-containing catalyst

A method of exchanging rare-isotope oxygen for common-isotope oxygen in the top several layers of an oxide-containing catalyst is disclosed. A sample of an oxide-containing catalyst is exposed to a flowing stream of reducing gas in an inert carrier gas at a temperature suitable for the removal of the reactive common-isotope oxygen atoms from the surface layer or layers of the catalyst without damaging the catalyst structure. The reduction temperature must be higher than any at which the catalyst will subsequently operate. Sufficient reducing gas is used to allow removal of all the reactive common-isotope oxygen atoms in the top several layers of the catalyst. The catalyst is then reoxidized with the desired rare-isotope oxygen in sufficient quantity to replace all of the common-isotope oxygen that was removed.

Robert V Hess↗
NASA NTRS1989

Chemistry of a polluted cloudy boundary layer

A one-dimensional photochemical model for cloud-topped boundary layers has been developed to include descriptions of gas- and aqueous-phase chemistry and the radiation field in and below the cloud. The model is applied to the accumulation of pollutants during a wintertime episode with low stratus over Bakersfield, CA. The mechanisms of sulfate production and the balance between the concentrations of acids and bases are examined. It is shown that most of the sulfate production may be explained by the Fe(III)-catalyzed autoxidation of S(IV). Another source of sulfate is the oxidation of SO2 by OH in both the gas and the aqueous phase. It is shown that the sulfate production in the model is controlled by the availability of NH3. It is suggested that this explains the balance observed between total concentration of acids and bases.

Jacob, Daniel J.↗
NASA NTRS1990

Studying marine stratus with large eddy simulation

Data sets from field experiments over the stratocumulus regime may include complications from larger scale variations, decoupled cloud layers, diurnal cycle, or entrainment instability, etc. On top of the already complicated turbulence-radiation-condensation processes within the cloud-topped boundary layer (CTBL), these complexities may sometimes make interpretation of the data sets difficult. To study these processes, a better understanding is needed of the basic processes involved in the prototype CTBL. For example, is cloud top radiative cooling the primary source of the turbulent kinetic energy (TKE) within the CTBL. Historically, laboratory measurements have played an important role in addressing the turbulence problems. The CTBL is a turbulent field which is probably impossible to generate in laboratories. Large eddy simulation (LES) is an alternative way of 'measuring' the turbulent structure under controlled environments, which allows the systematic examination of the basic physical processes involved. However, there are problems with the LES approach for the CTBL. The LES data need to be consistent with the observed data. The LES approach is discussed, and results are given which provide some insights into the simulated turbulent flow field. Problems with this approach for the CTBL and information from the FIRE experiment needed to justify the LES results are discussed.

Moeng, Chin-Hoh↗
NASA NTRS1986

Lidar measurements of the atmospheric entrainment zone and the potential temperature jump across the top of the mixed layer

Lidar data of the atmospheric entrainment zone from six days of clear air convection obtained in central Illinois during July 1979 are presented. A new method to measure the potential temperature jump across the entrainment zone based on only one temperature sounding and continuous lidar measurements of the mixed layer height is developed. An almost linear dependence is found between the normalized entrainment rate and the normalized thickness of the entrainment zone.

Boers, R.↗
NASA NTRS1988

Magnetic fields interacting with nonlinear compressible convection

Two-dimensional numerical simulations are used to study fully compressible convection in the presence of an imposed magnetic field. Highly nonlinear flows are considered that span multiple density scale heights. The convection tends to sweep the initially uniform vertical magnetic field into concentrated flux sheets with significant magnetic pressures. These flux sheets are partially evacuated, and effects of buoyancy and Lorentz forces there can serve to suppress motions. The flux sheets can be surrounded by a sheath of descending flow. If the imposed magnetic field is sufficiently strong, the convection can become oscillatory. The unstably stratified fluid layer has an initial density ratio (bottom to top of layer) of 11. Surveys of solutions at fixed Rayleigh number sample Chandrasekhar numbers from 1 to 1000 and magnetic Prandtl numbers from 1/16 to 1. These nonlinear simulations utilize a two-dimensional numerical scheme based on a modified two-step Lax-Wendroff method.

Hulburt, Neal E.↗
NASA NTRS2005

Solid Freeform Fabrication of Composite-Material Objects

Composite solid freeform fabrication (C-SFF) or composite layer manufacturing (CLM) is an automated process in which an advanced composite material (a matrix reinforced with continuous fibers) is formed into a freestanding, possibly complex, three-dimensional object. In CLM, there is no need for molds, dies, or other expensive tooling, and there is usually no need for machining to ensure that the object is formed to the desired net size and shape. CLM is a variant of extrusion-type rapid prototyping, in which a model or prototype of a solid object is built up by controlled extrusion of a polymeric or other material through an orifice that is translated to form patterned layers. The second layer is deposited on top of the first layer, the third layer is deposited on top of the second layer, and so forth, until the stack of layers reaches the desired final thickness and shape. The elements of CLM include (1) preparing a matrix resin in a form in which it will solidify subsequently, (2) mixing the fibers and matrix material to form a continuous pre-impregnated tow (also called "towpreg"), and (3) dispensing the pre-impregnated tow from a nozzle onto a base while moving the nozzle to form the dispensed material into a patterned layer of controlled thickness. When the material deposited into a given layer has solidified, the material for the next layer is deposited and patterned similarly, and so forth, until the desired overall object has been built up as a stack of patterned layers. Preferably, the deposition apparatus is controlled by a computer-aided design (CAD) system. The basic CLM concept can be adapted to the fabrication of parts from a variety of matrix materials. It is conceivable that a CLM apparatus could be placed at a remote location on Earth or in outer space where (1) spare parts are expected to be needed but (2) it would be uneconomical or impractical to store a full inventory of spare parts. A wide variety of towpregs could be prepared and stored on spools until needed. Long-shelf-life towpreg materials suitable for such use could include thermoplastic-coated carbon fibers and metal-coated SiC fibers. When a spare part was needed, the part could be fabricated by CLM under control by a CAD data file; thus, the part could be built automatically, at the scene, within hours or minutes.

Wang, C. Jeff↗
NASA NTRS2011

Vertical Structures of Anvil Clouds of Tropical Mesoscale Convective Systems Observed by CloudSat

A global study of the vertical structures of the clouds of tropical mesoscale convective systems (MCSs) has been carried out with data from the CloudSat Cloud Profiling Radar. Tropical MCSs are found to be dominated by cloud-top heights greater than 10 km. Secondary cloud layers sometimes occur in MCSs, but outside their primary raining cores. The secondary layers have tops at 6 8 and 1 3 km. High-topped clouds extend outward from raining cores of MCSs to form anvil clouds. Closest to the raining cores, the anvils tend to have broader distributions of reflectivity at all levels, with the modal values at higher reflectivity in their lower levels. Portions of anvil clouds far away from the raining core are thin and have narrow frequency distributions of reflectivity at all levels with overall weaker values. This difference likely reflects ice particle fallout and therefore cloud age. Reflectivity histograms of MCS anvil clouds vary little across the tropics, except that (i) in continental MCS anvils, broader distributions of reflectivity occur at the uppermost levels in the portions closest to active raining areas; (ii) the frequency of occurrence of stronger reflectivity in the upper part of anvils decreases faster with increasing distance in continental MCSs; and (iii) narrower-peaked ridges are prominent in reflectivity histograms of thick anvil clouds close to the raining areas of connected MCSs (superclusters). These global results are consistent with observations at ground sites and aircraft data. They present a comprehensive test dataset for models aiming to simulate process-based upper-level cloud structure around the tropics.

Hence, Deanna A.↗
NASA NTRS2011

Vertical Structures of Anvil Clouds of Tropical Mesoscale Convective Systems Observed by CloudSat

A global study of the vertical structures of the clouds of tropical mesoscale convective systems (MCSs) has been carried out with data from the CloudSat Cloud Profiling Radar. Tropical MCSs are found to be dominated by cloud-top heights greater than 10 km. Secondary cloud layers sometimes occur in MCSs, but outside their primary raining cores. The secondary layers have tops at 6--8 and 1--3 km. High-topped clouds extend outward from raining cores of MCSs to form anvil clouds. Closest to the raining cores, the anvils tend to have broader distributions of reflectivity at all levels, with the modal values at higher reflectivity in their lower levels. Portions of anvil clouds far away from the raining core are thin and have narrow frequency distributions of reflectivity at all levels with overall weaker values. This difference likely reflects ice particle fallout and therefore cloud age. Reflectivity histograms of MCS anvil clouds vary little across the tropics, except that (i) in continental MCS anvils, broader distributions of reflectivity occur at the uppermost levels in the portions closest to active raining areas; (ii) the frequency of occurrence of stronger reflectivity in the upper part of anvils decreases faster with increasing distance in continental MCSs; and (iii) narrower-peaked ridges are prominent in reflectivity histograms of thick anvil clouds close to the raining areas of connected MCSs (superclusters). These global results are consistent with observations at ground sites and aircraft data. They present a comprehensive test dataset for models aiming to simulate process-based upper-level cloud structure around the tropics.

Yuan, J.↗
NASA NTRS2015

High Operating Temperature Barrier Infrared Detector with Tailorable Cutoff Wavelength

A barrier infrared detector with absorber materials having selectable cutoff wavelengths and its method of manufacture is described. A GaInAsSb absorber layer may be grown on a GaSb substrate layer formed by mixing GaSb and InAsSb by an absorber mixing ratio. A GaAlAsSb barrier layer may then be grown on the barrier layer formed by mixing GaSb and AlSbAs by a barrier mixing ratio. The absorber mixing ratio may be selected to adjust a band gap of the absorber layer and thereby determine a cutoff wavelength for the barrier infrared detector. The absorber mixing ratio may vary along an absorber layer growth direction. Various contact layer architectures may be used. In addition, a top contact layer may be isolated into an array of elements electrically isolated as individual functional detectors that may be used in a detector array, imaging array, or focal plane array.

Ting, David Z.↗
NASA NTRS2019

Advances in Neural Network Detection and Retrieval of Multilayer Clouds for CERES Using Multispectral Satellite Data

An artificial neural network (ANN) algorithm, employing several Aqua MODIS infrared channels, the retrieved total cloud visible optical depth, and vertical humidity profiles is trained to detect multilayer (ML) ice-over-water cloud systems as identified by matched CloudSat and CALIPSO (CC) data. The multilayer ANN, or MLANN, algorithm is also trained to retrieve the optical depth and the top and base heights of the upper-layer ice clouds in ML systems. The trained MLANN was applied to independent MODIS data resulting in a combined ML and single layer hit rate of 80% (77%) for nonpolar regions during the day (night). The results are more accurate than currently available methods and the previous version of the MLANN. Upper-layer cloud top and base heights are accurate to ±1.2 km and ±1.6 km, respectively, while the uncertainty in optical depth is ±0.457 and ±0.556 during day and night, respectively. Areas of further improvement and development are identified and will be addressed in future versions of the MLANN.

CERES↗
NASA NTRS1990

Stratus: An interactive steady state mixed layer model for personal computers

A steady-state, horizontally homogeneous, cloud-topped marine boundary layer model based primarily on the work of Lilly (1968) and Schubert et al., (1979) is presented. The conservative thermodynamic variables are equivalent potential temperature, theta(sub e), and total water mixing ratio, q + l. Some of the differences between this and Lilly's (1968) model are: radiation is allowed to penetrate into the boundary layer; cloud top values of longwave radiation, equivalent potential temperature, and water vapor mixing ratio are linear functions of height derived from climatological data at California coastal stations; and the closure assumption assumes a weighted average of Lilly's (1968) maximum and minimum entrainment theories. This model was programmed in FORTRAN and will run interactively on an IBM-compatible personal computer. The program allows the user to specify the geographical location, the wind speed, the sea-surface temperature, the large scale horizontal divergence, and the initial guess for cloud top height. Output includes the steady state values of cloud top and cloud base height, mixed layer equivalent potential temperature and total water mixing ratio, and the associated convective and radiative fluxes.

Guinn, Thomas A.↗
NASA NTRS1997

Near-Surface Geologic Units Exposed Along Ares Vallis and in Adjacent Areas: A Potential Source of Sediment at the Mars Pathfinder Landing Site

A sequence of layers, bright and dark, is exposed on the walls of canyons, impact craters and mesas throughout the Ares Vallis region, Chryse Planitia, and Xanthe Terra, Mars. Four layers can be seen: two pairs of alternating dark and bright albedo. The upper dark layer forms the top surface of many walls and mesas. The upper dark-bright pair was stripped as a unit from many streamlined mesas and from the walls of Ares Valles, leaving a bench at the top of the lower dark layer, approximately 250 m below the highland surface on streamlined islands and on the walls of Ares Vallis itself. Along Ares Vallis, the scarp between the highlands surface and this bench is commonly angular in plan view (not smoothly curving), suggesting that erosion of the upper dark-bright pair of layers controlled by planes of weakness, like fractures or joints. These near-surface layers in the Ares Vallis area have similar thicknesses, colors, and resistances to erosion to layers exposed near the tops of walls in Valles Marineris (Treiman et al.) and may represent the same pedogenic hardpan units. From this correlation, and from analogies with hardpans on Earth, the light-color layers may be cemented by calcite or gypsum. The dark layers are likely cemented by an iron-bearing mineral. Mars Pathfinder instruments should permit recognition and useful analyses of hardpan fragments, provided that clean uncoated surfaces are accessible. Even in hardpan-cemented materials, it should be possible to determine the broad types of lithologies in the Martian highlands. However, detailed geochemical modeling of highland rocks and soils may be compromised by the presence of hardpan cement minerals.

Treiman, Allan H.↗
NASA NTRS1990

Millimeter-wave monolithic diode-grid frequency multiplier

A semiconductor diode structure useful for harmonic generation of millimeter or submillimeter wave radiation from a fundamental input wave is fabricated on a GaAs substrate. A heavily doped layer of n(sup ++) GaAs is produced on the substrate and then a layer of intrinsic GaAs on said heavily doped layer on top of which a sheet of heavy doping (++) is produced. A thin layer of intrinsic GaAs grown over the sheet is capped with two metal contacts separated by a gap to produce two diodes connected back to back through the n(sup ++) layer for multiplication of frequency by an odd multiple. If only one metal contact caps the thin layer of intrinsic GaAs, the second diode contact is produced to connect to the n(sup ++) layer for multiplication of frequency by an even number. The odd or even frequency multiple is selected by a filter. A phased array of diodes in a grid will increase the power of the higher frequency generated.

Maserjian, Joseph↗
NASA NTRS2001

Observation of Pollution Plume Capping by a Tropopause Fold

Airborne lidar measurements reveal a case in which a layer of high-ozone air extruding from a tropopause fold appears to cap a pollution plume and force it to spread out in the lower troposphere. The morphology of the high-ozone layer resembles a three-dimensional model of tropopause fold evolution that produces a low-altitude potential vorticity tube. This is a mechanism that can complete the irreversible transfer of air from the stratosphere, and can also affect pollution levels at the surface if the capping layer reaches the top of the boundary layer.

Cho, John Y. N.↗
NASA NTRS2002

Surface Composition of NiPd Alloys

Surface segregation in Ni-Pd alloys has been studied using the BFS method for alloys. Not only does the method predict an oscillatory segregation profile but it also indicates that the number of Pd-enriched surface planes can vary as a function of orientation. The segregation profiles were computed as a function of temperature, crystal face, and composition. Pd enrichment of the first layer is observed in (111) and (100) surfaces, and enrichment of the top two layers occurs for (110) surfaces. In all cases, the segregation profile shows oscillations that are actually related to weak ordering tendencies in the bulk. An atom-by-atom analysis was performed to identify the competing mechanisms leading to the observed surface behaviors. Large-scale atomistic simulations were also performed to investigate the temperature dependence of the segregation profiles as well as for analysis of the bulk structures. Finally, the observed surface behaviors are discussed in relation to the bulk phase structure of Ni-Pd alloys, which exhibit a tendency to weakly order.

Noebe, Ronald D.↗
NASA NTRS2003

Analysis of Surface and Bulk Behavior in Ni-Pd Alloys

The most salient features of the surface structure and bulk behavior of Ni-Pd alloys have been studied using the BFS method for alloys. Large-scale atomistic simulations were performed to investigate surface segregation profiles as a function of temperature, crystal face, and composition. Pd enrichment of the first layer was observed in (111) and (100) surfaces, and enrichment of the top two layers occurred for (110) surfaces. In all cases, the segregation profile shows alternate planes enriched and depleted in Pd. In addition, the phase structure of bulk Ni-Pd alloys as a function of temperature and composition was studied. A weak ordering tendency was observed at low temperatures, which helps explain the compositional oscillations in the segregation profiles. Finally, based on atom-by-atom static energy calculations, a comprehensive explanation for the observed surface and bulk features will be presented in terms of competing chemical and strain energy effects.

Bozzolo, Guillermo↗