SEARCH · Search NASA

Results for “Leading edges”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Application of a Flush Airdata Sensing System to a Wing Leading Edge (LE-FADS)

The feasibility of locating a flush airdata sensing (FADS) system on a wing leading edge where the operation of the avionics or fire control radar system will not be hindered is investigated. The leading-edge FADS system (LE-FADS) was installed on an unswept symmetrical airfoil and a series of low-speed wind-tunnel tests were conducted to evaluate the performance of the system. As a result of the tests it is concluded that the aerodynamic models formulated for use on aircraft nosetips are directly applicable to wing leading edges and that the calibration process is similar. Furthermore, the agreement between the airdata calculations for angle of attack and total pressure from the LE-FADS and known wind-tunnel values suggest that wing-based flush airdata systems can be calibrated to a high degree of accuracy. Static wind-tunnel tests for angles of attack from -50 deg to 50 deg and dynamic pressures from 3.6 to 11.4 lb/sq ft were performed.

Whitmore, Stephen A.↗

NASA NTRS1991

Effect of leading-edge geometry on boundary-layer receptivity to freestream sound

The receptivity to freestream sound of the laminar boundary layer over a semi-infinite flat plate with an elliptic leading edge is simulated numerically. The incompressible flow past the flat plate is computed by solving the full Navier-Stokes equations in general curvilinear coordinates. A finite-difference method which is second-order accurate in space and time is used. Spatial and temporal developments of the Tollmien-Schlichting wave in the boundary layer, due to small-amplitude time-harmonic oscillations of the freestream velocity that closely simulate a sound wave travelling parallel to the plate, are observed. The effect of leading-edge curvature is studied by varying the aspect ratio of the ellipse. The boundary layer over the flat plate with a sharper leading edge is found to be less receptive. The relative contribution of the discontinuity in curvature at the ellipse-flat-plate juncture to receptivity is investigated by smoothing the juncture with a polynomial. Continuous curvature leads to less receptivity. A new geometry of the leading edge, a modified super ellipse, which provides continuous curvature at the juncture with the flat plate, is used to study the effect of continuous curvature and inherent pressure gradient on receptivity.

Lin, Nay↗

NASA NTRS1989

On leading edge vortex and its control

A simple model for the leading edge vortex and a postulation for the existence of a critical vorticity concentration above which a stable leading edge vortex cannot be maintained were proposed. Using the model and postulation, various aspects of vortex control by blowing were discussed. Blowing can be envisioned as a means to control the effective sweep and span of a delta wing by redistributing the vorticity. Mixing between the blowing jet and the vortex has a major effect on the effectiveness of controlling the vortex. Different positioning of one vortex relative to another can either enhance or delay the breakdown of the vortices.

Ng, T. T.↗

NASA NTRS1985

Juncture flow control using leading-edge fillets

Flow measurements have been made in the wake region of a simulated wing-fuselage juncture, with and without leading-edge fillets, in order to assess the effect of leading-edge modifications on the flow field around the juncture. Preliminary results indicate that there is some reduction in juncture drag at moderate angles of attack with the use of leading-edge fillets. There is also evidence of improvement in the flow characteristics on the surface downstream of the juncture when fillets are used. As the fillet size is increased, flow characteristics start deteriorating at some point, and an optimum fillet size may be required to achieve an overall improvement in the flow field.

Kubendran, L. R.↗

NASA NTRS1977

Leading edge protection for composite blades

A laminated filament composite structure, such as an airfoil for use in an environment in which it is subjected to both foreign object impact and bending is provided with improved leading edge protection. At least one fine wire mesh layer is partially bonded within the composite structure along its neutral bending axis. A portion of the wire mesh layer extends beyond the neutral bending axis and partially around the leading edge where it is bonded to the outer periphery of the primary composite structure. The wire mesh is clad with a metal such as nickel to provide an improved leading edge protective device which is firmly anchored within the composite structure. Also described is a novel method of constructing a composite airfoil so as to further minimize the possibility of losing the leading edge protective device due to delamination caused by impact and bending.

Brantley, J. W.↗

NASA NTRS2005

Flexible Metallic Overwrap Concept Developed for On-Orbit Repair of Space Shuttle Orbiter Leading Edges

The Columbia accident has focused attention on the critical need for on-orbit repair concepts for leading edges in the event that damage is incurred during space shuttle orbiter flight. Damage that is considered as potentially catastrophic for orbiter leading edges ranges from simple cracks to holes as large as 16 in. in diameter. NASA is particularly interested in examining potential solutions for areas of larger damage since such a problem was identified as the cause for the Columbia disaster. One possible idea for the on-orbit repair of the reinforced carbon/carbon (RCC) leading edges is an overwrap concept that would use a metallic sheet flexible enough to conform to the contours of the orbiter and robust enough to protect any problem area from catastrophic failure during reentry. The simplified view of the application of a refractory metal sheet over a mockup of shuttle orbiter panel 9, which experiences the highest temperatures on the shuttle during reentry is shown. The metallic overwrap concept is attractive because of its versatility as well as the ease with which it can be included in an onboard repair kit. Reentry of the orbiter into Earth's atmosphere imposes extreme requirements on repair materials. Temperatures can exceed 1650 C for up to 15 min in the presence of an extremely oxidizing plasma environment. Several other factors are critical, including catalysity, emissivity, and vibrational and aerodynamic loads. Materials chosen for this application will need to be evaluated with respect to high-temperature capability, resistance to oxidation, strength, coefficient of thermal expansion, and thermal conductivity. The temperature profile across panel 9 during reentry as well as a schematic of the overwrap concept itself is shown.

Ritzert, Frank J.↗

NASA NTRS1982

Study of supersonic wings employing the attainable leading-edge thrust concept

A theoretical study was made of supersonic wing geometries at Mach 1.8, using the attainable leading-edge thrust concept. The attainable thrust method offers a powerful means to improve overall aerodynamic efficiency by identifying wing leading-edge geometries that promote attached flow and by defining a local angle-of-attack range over which attached flow may be obtained. The concept applies to flat and to cambered wings, which leads to the consideration of drooped-wing leading edges for attached flow at high lift coefficients.

Middleton, W. D.↗

NASA NTRS1974

Effect of canard position and wing leading-edge flap deflection on wing buffet at transonic speeds

A generalized wind-tunnel model, with canard and wing planform typical of highly maneuverable aircraft, was tested. The addition of a canard above the wing chord plane, for the configuration with leading-edge flaps undeflected, produced substantially higher total configuration lift coefficients before buffet onset than the configuration with the canard off and leading-edge flaps undeflected. The wing buffet intensity was substantially lower for the canard-wing configuration than the wing-alone configuration. The low-canard configuration generally displayed the poorest buffet characteristics. Deflecting the wing leading-edge flaps substantially improved the wing buffet characteristics for canard-off configurations. The addition of the high canard did not appear to substantially improve the wing buffet characteristics of the wing with leading-edge flaps deflected.

Gloss, B. B.↗

NASA NTRS1961

Effects of Mach Number, Leading-Edge Bluntness, and Sweep on Boundary-Layer Transition on a Flat Plate

The effects of leading-edge bluntness and sweep on boundary-layer transition on flat plate models were investigated at Mach numbers of 2.00, 2.50, 3.00, and 4.00. The effect of sweep on transition was also determined on a flat plate model equipped with an elliptical nose at a Mach number of 0.27. Models used for the supersonic investigation had leading-edge radii varying from 0.0005 to 0.040 inch. The free-stream unit Reynolds number was held constant at 15 million per foot for the supersonic tests and the angle of attack was 0 deg. Surface flow conditions were determined by visual observation and recorded photographically. The sublimation technique was used to indicate transition, and the fluorescent-oil technique was used to indicate flow separation. Measured Mach number and sweep effects on transition are compared with those predicted from shock-loss considerations as described in NACA Rep. 1312. For the models with the blunter leading edges, the transition Reynolds number (based on free-stream flow conditions) was approximately doubled by an increase in Mach number from 2.50 to 4.00; and nearly the same result was predicted from shock-loss considerations. At all super- sonic Mach numbers, increases in sweep reduced the transition Reynolds number and the amount of reduction increased with increases in bluntness. The shock-loss method considerably underestimated- the sweep effects, possibly because of the existence of crossflow instability associated with swept wings. At a Mach number of 0.27, no reduction in the transition Reynolds number with sweep was measured (as would be expected with no shock loss) until the sweep angle was attained where crossflow instability appeared.

Jillie, Don W.↗

NASA NTRS1992

Leading-edge receptivity for blunt-nose bodies

Boundary-layer receptivity in the leading edge region for bodies with blunt leading edges is investigated in this research program. Receptivity theory provides the link between the unsteady disturbance environment in the freestream and the initial amplitudes of instability waves in the boundary layer. This is a critical problem which must be addressed in order to develop more accurate prediction methods for boundary-layer transition.

Hammerton, P. W.↗

NASA NTRS1972

Leading-edge force features of the aerodynamic finite element method.

Description of a practical procedure for computing the wing leading-edge thrust distribution by the finite element method. When incorporated into a wing-body aerodynamic computer program, the technique is capable of predicting (at subsonic and supersonic speeds) the leading-edge thrust distribution (and therefore, the lateral-directional stability derivatives due to roll) and the nonlinear aerodynamic characteristics of low aspect-ratio wings with leading edge separation due to the application of suction technology.

Lan, C.-T.↗

NASA NTRS1971

A feasibility study of heat-pipe-cooled leading edges for hypersonic cruise aircraft

A theoretical study of the use of heat pipe structures for cooling the leading edges of hypersonic cruise aircraft was carried out over a Mach number range of 6 to 12. Preliminary design studies showed that a heat pipe cooling structure with a 33-in. chordwise length could maintain the maximum temperature of a 65 deg sweepback wing with a 0.5-in. leading edge radius below 1600 F during cruise at Mach 8. A few relatively minor changes in the steady-state design of the structure were found necessary to insure satisfactory cooling during the climb to cruise speed and altitude. It was concluded that heat pipe cooling is an attractive, feasible technique for limiting leading edge temperatures of hypersonic cruise aircraft.

Silverstein, C. C.↗

NASA NTRS1979

Improved prediction of laminar leading edge separation

Research was conducted to provide a definite criterion for the prediction of the bubble burst on airfoils typical of those used for fighter wings. The approach taken was to correlate existing airfoil bubble burst data using various parameters at the laminar separation point. The method due to Weber was modified to provide a continuous analytic solution for the velocity distribution around the airfoil leading edge. Coupling the modified Weber method with the Stratford laminar separation prediction method leads to a universal chart giving the conditions at separation as a function of stagnation location and leading edge radius. Application of the combined method to available two-dimensional airfoil data resulted in an empirical criterion presenting the limiting local velocity gradient at separation as a function of the boundary layer momentum thickness at separation for bubble burst. The correlation leads as well to the qualitative explanation of two types of laminar stall: thin airfoil and leading edge. The validity of the correlation is demonstrated by predicting the lift coefficient and angle of attack for stall on airfoils with leading edge or trailing edge flaps.

Herring, R. N.↗

NASA NTRSDate not supplied

Wall-Modeled Large-Eddy Simulations of a Swept Wing with Leading-Edge Ice

The aerodynamic performance of a swept wing derived from the Common Research Model wing with high-fidelity and smooth leading-edge ice shapes is evaluated using wall-modeled large-eddy simulations. Two mesh paradigms are considered within the Launch, Ascent, and Vehicle Aerodynamics framework: structured hybrid curvilinear body-fitted/immersed-boundary and unstructured Voronoi. The curvilinear approach models the effect of the ice on the flow through penalty terms and the Voronoi strategy includes the ice representation directly in the mesh.Aerodynamic loads, surface pressure profiles, and skin-friction streamlines are compared against experimental results collected at the Wichita State University wind tunnel at a Mach number of 0.18 and a Reynolds number per mean aerodynamic chord of 1.6 million. For the curvilinear simulations with high-fidelity ice, results are sensitive to spanwise mesh resolution near the leading edge, where insufficient spanwise resolution leads to a spanwise running vortexaft of the high-fidelity ice, which is partially removed with increasing spanwise resolution. For the Voronoi simulations with high-fidelity ice, refining the mesh led to good convergence towards the experimental results with the best case demonstrating a maximum discrepancy of three lift counts relative to the experiment across a range of angles of attack from about 5 to 24 degrees, validating the shrink-wrapping procedure used for the ice. For the smooth ice, the curvilinear approach consistently under-predicted the upper surface suction leading to an under-prediction in lift, but did not demonstrate the pronounced over-prediction in upper surface suction near the leading edge observed in the Voronoi simulations.

AATT↗

NASA NTRS1985

An assessment of some vorticity field-leading edge interactions

A review is undertaken of some recent advances in the following areas: the encounter of distributed and concentrated vorticity at a single frequency with a leading-edge, the interaction of multiple concentrations of vorticity with an edge, the distortion due to finite scale and angle of attack of the leading-edge, and the penetration of the leading-edge interaction into the near-wake region. Time-sequence flow visualization and phase-coordinated pressure measurements provide physical insight into the mechanisms of flow distortion and loading. Promising paths for future research are suggested on the basis of recent progress.

Rockwell, D.↗

NASA NTRS1974

Pressure measurements on the leading edge of a swept wing at Mach 2.2

Detailed pressure measurements were made on a flat semispan swept wing with a rounded leading edge at Mach number 2.2 through a range of Reynolds numbers. Pressure orifices were distributed in the streamwise direction at five spanwise stations on the leading edge and on the upper and lower surfaces. No significant amount of leading-edge suction was found, but the pressures and integrated normal forces on the upper and lower surfaces indicate the presence of a vortex lift.

Sorrells, R. B., III↗

NASA NTRS2010

Fracture Mechanics Analyses of the Slip-Side Joggle Regions of Wing-Leading Edge Panels

The Space Shuttle Orbiter wing comprises of 22 leading edge panels on each side of the wing. These panels are part of the thermal protection system that protects the Orbiter wings from extreme heating that take place on the reentry in to the earth atmosphere. On some panels that experience extreme heating, liberation of silicon carbon (SiC) coating was observed on the slip side regions of the panels. Global structural and local fracture mechanics analyses were performed on these panels as a part of the root cause investigation of this coating liberation anomaly. The wing-leading-edge reinforced carbon-carbon (RCC) panels, Panel 9, T-seal 10, and Panel 10, are shown in Figure 1 and the progression of the stress analysis models is presented in Figure 2. The global structural analyses showed minimal interaction between adjacent panels and the T-seal that bridges the gap between the panels. A bounding uniform temperature is applied to a representative panel and the resulting stress distribution is examined. For this loading condition, the interlaminar normal stresses showed negligible variation in the chord direction and increased values in the vicinity of the slip-side joggle shoulder. As such, a representative span wise slice on the panel can be taken and the cross section can be analyzed using plane strain analysis.

Raju, Ivatury S.↗

NASA NTRS2006

Heat-Pipe-Cooled Leading Edges for Hypersonic Vehicles

Heat pipes can be used to effectively cool wing leading edges of hypersonic vehicles. . Heat-pipe leading edge development. Design validation heat pipe testing confirmed design. Three heat pipes embedded and tested in C/C. Single J-tube heat pipe fabricated and testing initiated. HPCLE work is currently underway at several locations.

Glass, David E.↗