Search NASA⌕ Search

SEARCH · Search NASA

Results for “MACH NUMBER EFFECTS - PROPELLERS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1958

Effects of Nose Angle and Mach Number on Transition on Cones at Supersonic Speeds

An investigation has been made to determine the transition characteristics of a group of smooth, sharp-nosed cones varying from 10 degrees to sixty degrees in included apex angle over a Mach number range from 1.61 to 2.20 and a range of Reynolds number per foot from about 1.5 x 10 to the 6th power to 8 x 10 to the 6th power. Increasing the cone angle is shown to decrease slightly the transition Reynolds number, whereas the effects of changes of Mach number and unit Reynolds number are negligible. When transition occurred within 15 to 20 percent of the model length from the base there was a dropoff in transition Reynolds number. (author)

Czarnecki, K R↗
NASA NTRS1993

Stability of high speed compressible rotating Couette flow

In this study, we consider the linear stability of high speed, rotating Couette flow to two and three-dimensional disturbances in finite-gap spacings, including the full effects of compressibility and viscosity. Particularly, the combined effects of Mach number, Reynolds number, radial heating, and gap spacing are investigated. For a stationary outer cylinder, the primary instability is an axisymmetric mode independent of the Mach number. Increasing Mach numbers have a destabilizing effect for wide gaps, and a stabilizing effect for narrow gaps. For a sufficiently fast, counter-rotating outer cylinder, the primary instability becomes a three-dimensional traveling wave. Compressibility has a stabilizing effect on these modes regardless of the gap width; also, heating at the outer cylinder stabilizes the flow. Bicritical points for the primary instability corresponding to the crossover of the azimuthal wave numbers are determined for cylinders counter-rotating with equal angular speed.

Hatay, Ferhat F.↗
NASA NTRS1980

Low-speed aerodynamic characteristics of a 14-percent-thick NASA phase 2 supercritical airfoil designed for a lift coefficient of 0.7

The low speed aerodynamic characteristics of a 14 percent thick supercritical airfoil are documented. The wind tunnel test was conducted in the Low Turbulence Pressure Tunnel. The effects of varying chord Reynolds number from 2,000,000 to 18,000,000 at a Mach number of 0.15 and the effects of varying Mach number from 0.10 to 0.32 at a Reynolds number of 6,000,000 are included.

Harris, C. D.↗
NASA NTRS1948

The Development of Cambered Airfoil Sections Having Favorable Lift Characteristics at Supercritical Mach Numbers

Several groups of new airfoil sections, designated as the NACA 8-series, are derived analytically to have lift characteristics at supercritical Mach numbers which are favorable in the sense that the abrupt loss of lift, characteristic of the usual airfoil section at Mach numbers above the critical, is avoided. Aerodynamic characteristics determined, from two-dimensional windtunnel tests at Mach numbers up to approximately 0.9 are presented for each of the derived airfoils. Comparisons are made between the characteristics of these airfoils and the corresponding characteristics of representative NPiCA 6-series airfoils. The experimental results confirm the design expectations in demonstrating for the NACA S-series airfoils either no variation, or an Increase from the low-speed design value, In the lift coefficient at a constant angle of attack with increasing Mach number above the critical. It was not found possible to improve the variation with Mach number of the slope of the lift curve for these airfoils above that for the NACA 6-series airfoils. The drag characteristics of the new airfoils are somewhat inferior to those of the NACA 6- series with respect to divergence with Mach number, but the pitching-moment characteristics are more favorable for the thinner new sections In demonstrating somewhat smaller variations of moment coefficient with both angle of attack and Mach number. The effect on the aero&ynamic characteristics at high Mach numbers of removing the cusp from the trailing-edge regions of two 10-percent-chord-thick NACA 6-series airfoils is determined to be negligible.

AIRFOILS - NACA 836B110 - CHAR , MOMENTS & ORDINAT↗
NASA NTRS1991

Simulation and modeling of homogeneous compressible turbulence under isotropic mean compression

Compressible homogeneous turbulence subjected to isotropic mean compression is simulated numerically for high and low turbulent Mach numbers, at various compression rates. It is found that at low Mach numbers, the effects of viscosity variations on the development of the turbulent kinetic energy can be significant. A model consistent with the invariance of the Navier-Stokes equations to spherical compression, that takes into account variable viscosity effects is proposed. At high Mach numbers, the distribution of energy between the acoustic and solenoid fields is found to depend upon initial conditions. The simulation results are also used to evaluate two-equation compressible turbulence models.

Coleman, G. N.↗
NASA NTRS1976

Some factors influencing radiation of sound from flow interaction with edges of finite surfaces

Edges of surfaces which are exposed to unsteady flow cause both strictly acoustic effects and hydrodynamic effects, in the form of generation of new hydrodynamic sources in the immediate vicinity of the edge. An analytical model is presented which develops the explicit sound-generation role of the velocity and Mach number of the eddy convection past the edge, and the importance of relative scale lengths of the turbulence, as well as the relative intensity of pressure fluctuations. The Mach number (velocity) effects show that the important paramater is the convection Mach number of the eddies. The effects of turbulence scale lengths, isotropy, and spatial density (separation) are shown to be important in determining the level and spectrum of edge sound radiated for the edge dipole mechanism. Experimental data is presented which provides support for the dipole edge noise model in terms of Mach number (velocity) scaling, parametric dependence on flow field parameter, directivity, and edge diffraction effects.

Hayden, R. E.↗
NASA NTRS1993

High-altitude balloon-launched aircraft - A piloted simulation study

A real-time piloted simulation at the NASA Dryden Flight Research Facility was used to study the feasibility of launching a research aircraft from a high-altitude balloon. In the study, the simulated aircraft was launched in a nosedown attitude at zero airspeed from 110,000 ft. After launch, the pilot flew the aircraft through a near-maximum-lift pullout and then through a zoom climb to a trimmed, l-g flight condition at the test altitude. The study included parametric variations to measure the effects of launch altitude, gross weight, Mach number limit, and parachute size on the test altitude attained. The aerodynamic model of the simulated aircraft was based on flight test results, low Reynolds number windtunnel tests, and computational models; the model included significant Mach number and Reynolds number effects at high altitude. A small parachute was included in the simulation to limit Mach number during the pullout to avoid adverse transonic effects and their resultant energy losses. A small rocket motor was included in the simulation and was investigated for boosting the aircraft to a higher test altitude. In the study, a test altitude of approximately 95,000 ft was attained without rocket boost, and a test altitude in excess of 100,000 ft was attained using small rocket boost.

Murray, James E.↗
NASA NTRS1992

Piloted simulation study of a balloon-assisted deployment of an aircraft at high altitude

A piloted simulation was used to study the feasibility of a balloon assisted deployment of a research aircraft at high altitude. In the simulation study, an unmanned, modified sailplane was carried to 110,000 ft with a high altitude balloon and released in a nose down attitude. A remote pilot controlled the aircraft through a pullout and then executed a zoom climb to a trimmed, 1 g flight condition. A small parachute was used to limit the Mach number during the pullout to avoid adverse transonic effects. The use of small rocket motor was studied for increasing the maximum attainable altitude. Aerodynamic modifications to the basic sailplane included applying supercritical airfoil gloves over the existing wing and tail surfaces. The aerodynamic model of the simulated aircraft was based on low Reynolds number wind tunnel tests and computational techniques, and included large Mach number and Reynolds number effects at high altitude. Parametric variations were performed to study the effects of launch altitude, gross weight, Mach number limit, and parachute size on the maximum attainable stabilized altitude. A test altitude of approx. 95,000 ft was attained, and altitudes in excess of 100,000 ft was attained.

Murray, James↗
NASA NTRS1950

Experimental investigation of the effect of aspect ratio and Mach number on the flutter of cantilever wings

The results of some wind-tunnel experiments to investigate the effects of aspect ratio and Mach number on the flutter of uniform, unswept, cantilever wings are reported. Models having aspect ratios ranging from 2 to 13 were tested at Mach numbers up to 0.92. No general attempt is made to correlate the data with three-dimensional-flow theory, but an examination of the data is made on the basis of reference theoretical values obtained from the two-dimensional incompressible-flow theory. On this basis a reduction in aspect ratio, in general, increased the ratio of the experimental flutter speed to the calculated flutter speed. The analysis also indicated that for a given aspect ratio, this ratio decreased slightly as the Mach number is increased.

Widmayer, E , Jr↗
NASA NTRS1977

Analytical and experimental studies of acoustic performance of segmented liners in a compressor inlet

The performance of axially segmented (phased) acoustic treatment liners in the inlet of a compressor was investigated. Topics discussed include: (1) the validation of a theoretical procedure to predict propagation and suppression characteristics of duct liners; (2) the in-duct measurement of spinning modes; (3) investigation of phased treatment designs; (4) high Mach inlet acoustic tests; and (5) an experimental investigation of inlet turbulence. The analytical prediction for the multi-segmented treatment was found to provide the correct order of magnitude of suppression and was generally within 50% of that determined experimentally. Refinements required to improve the correlation are identified. Suppression due to high subsonic Mach number flow effects was found to become significant above an average throat Mach number of 0.65 to 0.7 and 20 PNdB was achieved with an average throat Mach number in the range of 0.80 to 0.85. For the measured turbulence in the inlet, including the axial and circumferential turbulence intensities and the axial integral length scale, data are presented with and without an inlet screen showing that the screen reduced the turbulence intensities and that the BPF noise was reduced as a consequence.

Motsinger, R. E.↗
NASA NTRS1961

Transition of the Laminar Boundary Layer on a Delta Wing with 74 degree Sweep in Free Flight at Mach Numbers from 2.8 to 5.3

The tests were conducted at Mach numbers from 2.8 to 5.3, with model surface temperatures small compared to boundary-layer recovery temperature. The effects of Mach number, temperature ratio, unit Reynolds number, leading-edge diameter, and angle of attack were investigated in an exploratory fashion. The effect of heat-transfer condition (i.e., wall temperature to total temperature ratio) and Mach number can not be separated explicitly in free-flight tests. However, the data of the present report, as well as those of NACA TN 3473, were found to be more consistent when plotted versus temperature ratio. Decreasing temperature ratio increased the transition Reynolds number. The effect of unit Reynolds number was small as was the effect of leading-edge diameter within the range tested. At small values of angle of attack, transition moved forward on the windward surface and rearward on the leeward surface. This trend was reversed at high angles of attack (6 deg to 18 deg). Possible reasons for this are the reduction of crossflow on the windward side and the influence of the lifting vortices on the leeward surface. When the transition results on the 740 delta wing were compared to data at similar test conditions for an unswept leading edge, the results bore out the results of earlier research at nearly zero heat transfer; namely, sweep causes a large reduction in the transition Reynolds number.

Chapman, Gary T.↗
NASA NTRS1951

Investigations on wings with and without sweepback at high subsonic speeds

Drag tests at zero lift have been made at Mach numbers from 0.7 to approximately 0.95 in the high speed wind tunnel of the Institute of Aerodynamics, ETH, Zurich, on a group of untapered wings of aspect ratio 3.25, having sweep angles of 0 degree and 35 degrees. For each sweep angle, a series of geometrically similar models was tested at a constant Reynolds number to provide a verification of computed tunnel blocking corrections. Tests were also made for wings having thickness ratios of 0.09 and 0.12 and the results compared with results predicted by von Karman's similarity law.

RESEARCH TECHNIQUE - CORRECTIONS↗
NASA NTRS1961

Experimental Investigation at Mach Number 3.0 of the Effects of Thermal Stress and Buckling on the Flutter of Four-Bay Aluminum Alloy Panels with Length-Width Ratios of 10

Skin-stiffener aluminum alloy panels consisting of four bays, each bay having a length-width ratio of 10, were tested at a Mach number of 3.0 at dynamic pressures ranging from 1,500 psf to 5,000 psf and at stagnation temperatures from 300 F to 655 F. The panels were restrained by the supporting structure in such a manner that partial thermal expansion of the skins could occur in both the longitudinal and lateral directions. A boundary faired through the experimental flutter points consisted of a flat-panel portion, a buckled-panel portion, and a transition point at the intersection of the two boundaries. In the region where a panel must be flat when flutter occurs, an increase in panel skin temperature (or midplane compressive stress) makes the panel more susceptible to flutter. In the region where a panel must be buckled when flutter occurs, the flutter trend is reversed. This reversal in trend is attributed to the panel postbuckling behavior.

Dixon, Sidney C.↗