Search NASA⌕ Search

SEARCH · Search NASA

Results for “MACH NUMBER EFFECTS - WING SECTIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

On the application of a linearized unsteady potential-flow analysis to fan-tip cascades

A linearized potential flow analysis, which accounts for the effects of nonuniform steady flow phenomena on the unsteady response to prescribed blade motions, has been applied to five two-dimensional cascade configurations. These include a flat-plate cascade and three cascades which are representative of the tip sections of current fan designs. Here the blades are closely spaced, highly staggered, and operate at low mean incidence. The fifth configuration is a NASA Lewis cascade of symmetric biconvex airfoils for which experimental measurements are available. Numerical solutions are presented that clearly illustrate the effects and importance of blade geometry and mean blade loading on the linearized unsteady response at high subsonic inlet Mach number and high blade-vibrational frequency. In addition, a good qualitative agreement is shown between the analytical predictions and experimental measurements for the cascade of symmetric biconvex airfoils. Finally, recommendations on the research needed to extend the range of application of linearized unsteady aerodynamic analyses are provided.

Usab, W. J., Jr.↗
NASA NTRS1991

Evaluation of tunnel sidewall boundary-layer-control systems for high-lift airfoil testing

An experimental study was conducted in the NASA Langley Low-Turbulence Pressure Tunnel to evaluate a suction sidewall boundary-layer-control (BLC) technique used in testing 2D high-lift airfoils. Sidewall BLC is required to maintain spanwise two-dimensionality of the flow over the airfoil at large angles of attack. A supercritical-type high-lift air-foil, equipped with a double-slotted flap and a leading-edge slat, was used for the study which was conducted at a Mach number of 0.2 and Reynolds numbers based on chord of 9 and 16 million. The sidewall BLC technique, which features distributed suction through porous endplates connected to a venting system, was able to control sidewall boundary-layer separation and maintain two-dimensional flow over the high-lift configuration for both Reynolds numbers tested. Discussions on porous endplate optimization and effects of suction on section lift are presented. Results obtained with the suction system were also compared with previous data obtained with a tangential blowing BLC system for the same high-lift configuration.

Paschal, K.↗
NASA NTRS1977

The effect of blade sweep on propeller performance

The advanced propeller developed for high Mach number cruise incorporates swept blades to reduce compressibility losses. In order to evaluate the induced flow-field vortex lattice methods are applied to a swept propeller blade. The blade is modeled by a radial distribution of helical horseshoe vortices with a single swept bound vortex at the quarter chord and the control point at the three-quarter chord of each radial section. The results of numerical calculations show that the power coefficient decreases as the blade is swept and the power loading distribution shifts inboard.

Sullivan, J. P.↗
NASA NTRS1994

Pressure-sensing performance of upright cylinders in a Mach 10 boundary-layer

An experimental research program to provide basic knowledge of the pressure-sensing performance of upright, flushported cylinders in a hypersonic boundary layer is described. Three upright cylinders of 0.25-, 0.5- and l.0-in. diameters and a conventional rake were placed in the test section sidewall boundary layer of the 31 Inch Mach 10 Wind Tunnel at NASA Langley Research Center, Hampton, Virginia. Boundary-layer pressures from these cylinders were compared to those measured with a conventional rake. A boundary-layer thickness-to-cylinder-diameter ratio of 8 proved sufficient to accurately measure an overall pressure profile and ascertain the boundary-layer thickness. Effects of Reynolds number, flow angularity, and shock wave impingement on pressure measurement were also investigated. Although Reynolds number effects were negligible at the conditions studied, flow angularity above 10 deg significantly affects the measured pressures. Shock wave impingement was used to investigate orifice-to-orifice pressure crosstalk. No crosstalk was measured. The lower pressure measured above the oblique shock wave impingement showed no influence of the higher pressure generated at the lower port locations.

Johnson, Steven↗
NASA NTRS1993

Turbulence model evaluation for the prediction of flows over a supercritical airfoil with deflected aileron at high Reynolds number

Navier-Stokes solutions about a supercritical airfoil with aileron deflection have been computed using the CFL3D code coupled with the Baldwin-Lomax, Johnson-King, Baldwin-Barth, and Spalart-Allmaras turbulence models. Computations were made at a Mach number of 0.716 and chord Reynolds numbers of 5, 15, and 25 million. The airfoil was analyzed with both 0 deg and 2 deg (TED) aileron deflections. Comparisons over a range of angles-of-attack showed that solutions obtained using the Baldwin-Barth turbulence model presented the best agreement with experimental pressures and sectional lift coefficients. However, Reynolds number trends in sectional lift coefficient and in aileron effectiveness were not predicted consistently.

Londenberg, W. K.↗
NASA NTRS1996

Experimental investigation of unsteady flows at large incidence angles in a linear oscillating cascade

The aerodynamics of a cascade of airfoils oscillating in torsion about the midchord is investigated experimentally at a large mean incidence angle and, for reference, at a low mean incidence angle. The airfoil section is representative of a modern, low aspect ratio, fan blade tip section. Time-dependent airfoil surface pressure measurements were made for reduced frequencies up to 0.8 for out-of-phase oscillations at Mach numbers up to 0.8 and chordal incidence angles of 0 deg and 10 deg. For the 10 deg chordal incidence angle, a separation bubble formed at the leading edge of the suction surface. The separated flow field was found to have a dramatic effect on the chordwise distribution of the unsteady pressure. In this region, substantial deviations from the attached flow data were found with the deviations becoming less apparent in the aft region of the airfoil for all reduced frequencies. In particular, near the leading edge the separated flow had a strong destabilizing influence while the attached flow had a strong stabilizing influence.

Buffum, Daniel H.↗
NASA NTRS1973

Supersonic aerodynamic characteristics of hypersonic low-wave-drag elliptical body-tail combinations as affected by changes in stabilizer configuration

An investigation has been made at Mach numbers from 1.50 to 4.63 to determine systematically the effects of the addition and position of outboard stabilizers and vertical- and vee-tail configurations on the performance and stability characteristics of a low-wave-drag elliptical body. The basic body shape was a zero-lift hypersonic minimum-wave-drag body as determined for the geometric constraints of length and volume. The elliptical cross section had an axis ratio of 2 (major axis horizontal) and an equivalent fineness ratio of 6.14. Base-mounted outboard stabilizers were at various dihedral angles from 90 deg to minus 90 deg with and without a single center-line vertical tail or a vee-tail. The angle of attack was varied from about minus 6 to 27 deg at sideslip angles of 0 and 5 deg and a constant Reynolds number of 4.58 x one million (based on body length).

Spencer, B., Jr.↗
NASA NTRS1991

Wall-interference assessment and corrections for transonic NACA 0012 airfoil data from various wind tunnels

A nonlinear, four wall, post-test wall interference assessment/correction (WIAC) code was developed for transonic airfoil data from solid wall wind tunnels with flexibly adaptable top and bottom walls. The WIAC code was applied over a broad range of test conditions to four sets of NACA 0012 airfoil data, from two different adaptive wall wind tunnels. The data include many test points for fully adapted walls, as well as numerous partially adapted and unadapted test points, which together represent many different model/tunnel configurations and possible wall interference effects. Small corrections to the measured Mach numbers and angles of attack were obtained from the WIAC code even for fully adapted data; these corrections generally improve the correlation among the various sets of airfoil data and simultaneously improve the correlation of the data with calculations for a 2-D, free air, Navier-Stokes code. The WIAC corrections for airfoil data taken in fully adapted wall test sections are shown to be significantly smaller than those for comparable airfoil data from straight, slotted wall test sections. This indicates, as expected, a lesser degree of wall interference in the adapted wall tunnels relative to the slotted wall tunnels. Application of the WIAC code to this data was, however, somewhat more difficult and time consuming than initially expected from similar previous experience with WIAC applications to slotted wall data.

Green, Lawrence L.↗
NASA NTRS1991

A laser velocimeter investigation of the normal shock-wave boundary layer interaction

Nonintrusive 3-D measurements were made of a normal shock wave/turbulent boundary layer interaction. The measurements were made through a quadrant of a square test section of a continuous flow supersonic wind tunnel in which a normal shock wave had been stabilized. Two dimensional measurements were made throughout the interaction region while 3-D measurements were made near the corner in the vicinity of the shock where 3-D flow effects were expected to be significant. Laser Doppler velocimetry, surface static pressure measurements, and flow visualization techniques were used for two freestream nominal Mach number test cases: 1.6 and 1.3. No turbulence information was obtained. The mean velocity measurements were converted to Mach number by recording the wind tunnel total temperature. Some shock oscillation was present during both of the test cases. After startup of the wind tunnel, the shock oscillated with an amplitude of approx. + or - 1 cm, however, after reaching steady condition, the shock oscillation amplitude was greatly reduced, as evidenced by the laser velocimeter results. The Mach 1.3 test case resulted in a nearly uniform flow without secondary shock waves and with no or very isolated corner separation.

Chriss, Randall M.↗
NASA NTRS1961

Hovering Characteristics of a Rotor having an Airfoil Section Designed for Flying-Crane Type of Helicopter

Results of an investigation, conducted on the Langley helicopter test tower, of a rotor having an NACA 632A015 airfoil thickness distribution in combination with an NACA 230 mean line are presented. Comparison with a previously reported test of a symmetrical rotor blade efficiency was substantially improved over a wide range of tip Mach numbers. The maximum mean lift coefficient was essentially unchanged from that obtained with uncambered blades. Some data showing the effect of a distributed type of leading-edge roughness are also included.

Shivers, James P.↗
NASA NTRS1975

Effects of geometric variables on the performance of a probe for direct measurement of free-steam stagnation pressure in supersonic flow

An investigation was conducted at Mach numbers of 1.41, 1.83, and 2.20 to determine the effects of parametric variations in the height of the pitot-tube center line from the probe surface and in the radius of the surface curvature on the pressure recovery of a probe designed to measure the free-stream stagnation pressure. The probe consists of a pitot tube mounted on the surface of a curved cylinder of circular cross section. The pitot tube senses the pressure of the stream tube which has been slowed by isentropic compression along the curved surface. Pressure recovery, greater than or equal to 99.8 percent of the free-stream stagnation pressure, was obtained for a wide range both of angle of attack and of yaw for probes satisfying the predetermined optimum design criteria.

Couch, L. M.↗
NASA NTRS1976

Mach 4 free-jet tunnel starting experiments for a hypersonic research engine model causing high blockage

Tests of a full scale hypersonic research engine (HRE) were conducted in the hypersonic tunnel facility at Mach numbers of 5, 6, and 7. Since the HRE would cause a rather high blockage (48.83 percent of the nozzle area), subscale tests were conducted in various available small wind tunnels prior to the full scale tests to study the effects of model blockage on tunnel starting. The results of the Mach 4 subscale tests which utilized a model system at 0.0952 scale which simulated the HRE in the test section of the tunnel are presented. A satisfactory tunnel starting could not be achieved by varying the free jet length or diffuser size nor by inserting the model into the test stream after tunnel starting. However, the installation of a shroud around the HRE model allowed the tunnel to start with the model preset in the tunnel at a tunnel stagnation pressure to atmospheric exit pressure ratio of 13.4. The simulation of the discharge of instrumentation cooling water and the addition of test hardware at the aft end of the HRE model did not have a significant effect on the tunnel starting.

Carson, G. T., Jr.↗
NASA NTRS1989

Automatic control of cryogenic wind tunnels

Inadequate Reynolds number similarity in testing of scaled models affects the quality of aerodynamic data from wind tunnels. This is due to scale effects of boundary-layer shock wave interaction which is likely to be severe at transonic speeds. The idea of operation of wind tunnels using test gas cooled to cryogenic temperatures has yielded a quantrum jump in the ability to realize full scale Reynolds number flow similarity in small transonic tunnels. In such tunnels, the basic flow control problem consists of obtaining and maintaining the desired test section flow parameters. Mach number, Reynolds number, and dynamic pressure are the three flow parameters that are usually required to be kept constant during the period of model aerodynamic data acquisition. The series of activity involved in modeling, control law development, mechanization of the control laws on a microcomputer, and the performance of a globally stable automatic control system for the 0.3-m Transonic Cryogenic Tunnel (TCT) are discussed. A lumped multi-variable nonlinear dynamic model of the cryogenic tunnel, generation of a set of linear control laws for small perturbation, and nonlinear control strategy for large set point changes including tunnel trajectory control are described. The details of mechanization of the control laws on a 16 bit microcomputer system, the software features, operator interface, the display and safety are discussed. The controller is shown to provide globally stable and reliable temperature control to + or - 0.2 K, pressure to + or - 0.07 psi and Mach number to + or - 0.002 of the set point value. This performance is obtained both during large set point commands as for a tunnel cooldown, and during aerodynamic data acquisition with intrusive activity like geometrical changes in the test section such as angle of attack changes, drag rake movements, wall adaptation and sidewall boundary-layer removal. Feasibility of the use of an automatic Reynolds number control mode with fixed Mach number control is demonstrated.

Balakrishna, S.↗
NASA NTRS1975

Effect of slot width on transition and noise attenuation of a flat sound shield in a Mach 6 wind tunnel

An experimental and theoretical study of a sound shield concept to attenuate the noise radiated into the test section from the turbulent boundary layer on the walls of wind tunnels was conducted. The model investigated was planar with a sharp flat plate leading edge faired into an array of rods aligned nearly parallel to the local flow. For a ratio of gap diameter to rod diameter of 0.16, the flow was laminar over the entire model at a maximum local length Reynolds number of 14 million. A 45% reduction in the tunnel free stream root mean square pressure level was measured within the shielded region for this gap width when the boundary layers on the rods were laminar. Smaller ratios of gap diameter to rod diameter resulted in substantial reductions in the transition Reynolds number, and in a 40% pressure reduction.

Stainback, P. C.↗
NASA NTRS1994

Calibration of Axisymmetric and Quasi-1D Solvers for High Enthalpy Nozzles

The proposed paper will present a numerical investigation of the flow characteristics and boundary layer development in the nozzles of high enthalpy shock tunnel facilities used for hypersonic propulsion testing. The computed flow will be validated against existing experimental data. Pitot pressure data obtained at the entrance of the test cabin will be used to validate the numerical simulations. It is necessary to accurately model the facility nozzles in order to characterize the test article flow conditions. Initially the axisymmetric nozzle flow will be computed using a Navier Stokes solver for a range of reservoir conditions. The calculated solutions will be compared and calibrated against available experimental data from the DLR HEG piston-driven shock tunnel and the 16-inch shock tunnel at NASA Ames Research Center. The Reynolds number is assumed to be high enough at the throat that the boundary layer flow is assumed turbulent at this point downstream. The real gas affects will be examined. In high Mach number facilities the boundary layer is thick. Attempts will be made to correlate the boundary layer displacement thickness. The displacement thickness correlation will be used to calibrate the quasi-1D codes NENZF and LSENS in order to provide fast and efficient tools of characterizing the facility nozzles. The calibrated quasi-1D codes will be implemented to study the effects of chemistry and the flow condition variations at the test section due to small variations in the driver gas conditions.

Papadopoulos, P. E.↗
NASA NTRS2012

Evaluation of Wall Boundary Conditions for Impedance Eduction Using a Dual-Source Method

The accuracy of the Ingard-Myers boundary condition and a recently proposed modified Ingard-Myers boundary condition is evaluated for use in impedance eduction under the assumption of uniform mean flow. The evaluation is performed at three centerline Mach numbers, using data acquired in a grazing flow impedance tube, using both upstream and downstream propagating sound sources, and on a database of test liners for which the expected behavior of the impedance spectra is known. The test liners are a hard-wall insert consisting of 12.6 mm thick aluminum, a linear liner without a facesheet consisting of a number of small diameter but long cylindrical channels embedded in a ceramic material, and two conventional nonlinear liners consisting of a perforated facesheet bonded to a honeycomb core. The study is restricted to a frequency range for which only plane waves are cut on in the hard-wall sections of the flow impedance tube. The metrics used to evaluate each boundary condition are 1) how well it educes the same impedance for upstream and downstream propagating sources, and 2) how well it predicts the expected behavior of the impedance spectra over the Mach number range. The primary conclusions of the study are that the same impedance is educed for upstream and downstream propagating sources except at the highest Mach number, that an effective impedance based on both the upstream and downstream measurements is more accurate than an impedance based on the upstream or downstream data alone, and that the Ingard-Myers boundary condition with an effective impedance produces results similar to that achieved with the modified Ingard-Myers boundary condition.

Watson, W. R.↗
NASA NTRS1972

Stability of combustors with partial length acoustic liners

An analytical technique for the evaluation of combustion stability in rocket motors with partial length acoustic absorbers is presented. The combustors considered have concentrated combustion zones at the injector, finite mean flows, cylindrical cross sections, and acoustic liners of arbitrary length and impedance. Linear three dimensional oscillations in such combustion chambers are analyzed using an integral equation-iteration technique. Stability limits in terms of a combustion response factor are calculated for several values of Mach number, length to radius ratio, liner impedance, liner length, liner location, and nozzle admittance. Results indicate that increasing liner length increases combustor stability substantially at low Mach numbers but has a substantially smaller effect for larger Mach numbers. Increasing Mach numbers or length to radius ratio have destabilizing effects while liner location has only a minor effect on stability.

Mitchell, C. E.↗
NASA NTRS1972

Stability of combustors with partial length acoustic liners.

An analytical technique for the evaluation of combustion stability in rocket motors with partial length acoustic liners is presented. The combustors considered in this work have concentrated combustion zones at the injector, finite mean flows, cylindrical cross sections, and acoustic liners of arbitrary length and impedance. Linear three dimensional oscillations in such combustion chambers are analyzed using an integral equation-iteration technique. Stability limits in terms of the sensitive time lag model are calculated for several values of Mach number, length to radius ratio, liner impedance, liner length, liner location, and nozzle admittance. Results indicate that increasing liner length increases combustor stability substantially at low Mach numbers but has a considerably smaller effect for larger Mach numbers. Increasing Mach number or length to radius ratio has a destabilizing effect while liner location has only a minor effect on stability.

Mitchell, C. E.↗