Search NASA⌕ Search

SEARCH · Search NASA

Results for “METAL FUEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

First Examination of Irradiated Fuel with Pulsed Neutrons at LANSCE (Preliminary Results)

We present preliminary results on the characterization of an irradiated U-lOZr-lPd fuel sample that was prepared from the irradiated AFC-3A-R5A sample. U-lOZr metallic fuels are researched as host materials for potential transmutation fuels and the addition of palladium strives to bind lanthanides, thus preventing fuel-cladding chemical interactions (FCCI). These interactions limit the lifetime of metallic fuels and are caused by migration of lanthanide fission products to the periphery of the fuel slug, where they start to interact with the D9 or HT9 steel cladding, ultimately leading to failure of the mechanical integrity of the cladding. Neutrons offer bulk characterization of irradiated materials for which X-ray tomography methods are not suitable due to the immense gamma background emitted from the samples. In particular pulsed neutrons provide information from the ability to resolve the neutron energy using their time-of-flight and thus the potential to utilize neutron absorption resonance to characterize the spatial distribution of isotopes. This, in turn, may allow to characterize the distribution of fission and neutron capture products non-destructively and may ultimately be applied to the bulk of an irradiation capsule prior to destructive post-irradiation examination to identify regions of interest. To allow the characterization of entire irradiation capsules, a cask is under development in the advanced post-irradiation work package at LANL and progress on this development was reported elsewhere. In parallel, an irradiated U-lOZr-lPd sample cut from the AFC-3AR5A irradiation was shipped to LANL and will be fully characterized with an NSUF funded rapid turnaround experiment (RTE) in the 2020 LANSCE run cycle. The sample emits at a dose rate of ~3R/hr on contact and is therefore manageable with remote handling, without requiring a cask. The disk-shaped material is larger than samples prepared for analysis using electron or X-ray methods and is therefore an intermediate step towards characterization of bulk samples at LANSCE. However, since it covers the full diameter of the irradiated fuel slug, some insight on redistribution of elements, spatially resolved information on microstructure, e.g. phase composition and texture, will be possible using the pulsed neutron-based methods developed for fuel characterization at LANSCE. This report describes the development of procedures to handle the sample at LANSCE as well as preliminary data and results from tests conducted in December 2019 on the energy-resolved neutron imaging (ERNI) beam line at flight path 5 and the high pressure-preferred orientation diffractometer (HIPPO) at LANSCE. This effort is a collaboration between LANL, INL, and ORNL. To compare our capabilities with prior work, we present an overview of previously reported bulk characterization of irradiated or spent fuels. The overview addresses neutron diffraction and neutron absorption resonance spectroscopy, both of which have only few reported applications on irradiated or spent nuclear fuel, as well as neutron radiography. This literature review was already described in a previous report but is repeated here to put our current efforts in context of previous work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Phosphate-Based Approaches for Dechlorination and Treatment of Salt Waste from Electrochemical Processing of Used Nuclear Fuel: A Perspective on Recent Work

Phosphate-based reagents are being considered by the U.S. Department of Energy (DOE) Office of Nuclear Energy to process halide salt-based nuclear wastes for stabilization prior to disposal. As evidenced by the Experimental Breeder Reactor-II (EBR-II) project, electrochemical processing (pyroprocessing) can be employed to recover uranium and other actinides for reintegration into the nuclear fuel cycle from metallic fuels. The resultant salt-based wastes generated from electrochemical processing of EBR-II fuel contains fission products within a LiCl–KCl eutectic salt that necessitate appropriate disposal. This paper provides an overview of recent efforts to support halide-based salt waste treatment for disposition, as well as a basis for comparison with other related efforts in salt waste treatment through salt partitioning initiatives. The U.S. DOE has selected a phosphate waste form reference material for further investigation and longer-term studies.

electrorefiner↗
DOE OSTI2023

Bison Verification and Validation Activities for TRISO

Numerical modeling and simulation (M&S) tools play a key role in the research, development, and overall safety assessments of next-generation nuclear energy systems. One such tool, Bison, is a nuclear fuel performance code that is applicable to many fuel forms (e.g., light-water reactor fuel, oxide and metallic fuel for fast reactors, tri-structural isotropic (TRISO) fuel, and plate fuel), and it uses the finite element method to model the thermo- mechanical response of nuclear fuels. One fuel form widely utilized in Generation-IV high-temperature gas-cooled and fluoride- salt-cooled nuclear reactor concepts is TRISO fuel. Recently, Bison’s capabilities were significantly expanded to enable it to model the performance of TRISO particles and compacts. It is important that Bison’s computational results be reliable and predictive, since this code is used to inform high-consequence decisions. The various processes developed to address this issue generally entail two fundamental steps: verification and validation (V&V). Verification ensures that the code functions correctly and is reliable. Code/solution verification, code benchmark, and software quality assurance exercises are examples of verification activities. On the other hand, validation is the process of assessing a code’s capability to accurately model physical problems. Comparisons between code results and experiments quantify the validation level. Application of V&V procedures is crucial to the development of computational tools that are free of coding mistakes and can accurately represent reality. The current study presents an overview of Bison V&V activities relevant to the TRISO fuel concept, which include code/solution verification exercises, CRP-6 Benchmark—a Coordinated Research Program through the International Atomic Energy Agency (IAEA)—exercises, and validation exercises with the Advanced Gas Reactor (AGR)- 1/2/3/4 experiment series.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Development and Integration of a Stochastic Clad Damage Propagation Model into PRONGHORN-SC Subchannel Analysis Code

The failure of fuel pins in nuclear reactors is intrinsically stochastic. Typically, a combination of variation in manufacturing that affects the material characteristics and the fuel assembly dimensions, variation in operating conditions, such as local power, coolant flow rate, and irradiation induced changes in material properties lead to a large uncertainty in failure margin of the fuel pins. Failure, therefore, may occur in exceptional pins with adverse combinations of these variations. Upon a metal fuel pin (U-Pu-Zr/HT9) failure, depressurization of the fuel pin takes place by release of fission gas, liquid sodium bond, and potentially solid fuel particles or molten/eutectic fuel droplets through the hole in cladding. The effect of a fission gas jet on neighbor fuel pins and possible propagation of a clad damage during normal operation was studied experimentally in 1970s and it was found that the post-failure fission gas jet insulates the jet impingement area of the target fuel pin surface and could increase the target pin’s surface temperature by as much as 100 – 200 K during the failed pin depressurization. It was concluded that the effect should not lead to fuel pin failure propagation during normal operation. In accident scenarios of sodium and lead fast reactors such as Unprotected Loss-Of-Flow (ULOF) or Unprotected Transient Over Power (UTOP), the fuel pins can be subjected to higher clad temperatures and fuel pin pressures or fuel clad mechanical/chemical interaction where thermal creep margin becomes significantly lower compared to the normal operation conditions. Therefore, possible stochastic failure and the post-failure fission gas/fuel jet impingement could be critical in order to predict fuel pin failure propagation. Pin depressurization due to fission gas release may degrade the heat transfer by formation of a gas blanket on a neighboring pin surface, which is a local phenomenon, and by causing coolant flow deceleration and starvation, which could affect a surrounding region as well. Furthermore, the potential presence of solid fuel particles or molten fuel at the time of clad failure could boost post-failure jet induced degradation even further. The present study models the U-Pu-Zr/HT9 metal fuel pin failure and stochastic clad damage propagation by biased sampling based on a Cumulative Damage Fraction (CDF) type clad failure criterion and the normal distribution of fuel failure probability density as a function of logarithm of Cumulative Damage Fraction. In addition, the effect of post-failure fission gas jet on heat transfer degradation is modeled for the target pins. This model is called stochastic Clad Damage Propagation (CDAP). The CDAP model is now fully integrated into developmental version of PRONGHORN-SC subchannel analysis code, allowing for modeling local failures and its propagation potential. Section 2 describes the components of the CDAP models. Section 3 describes the model implementation to PRONGHORN-SC and input specifications. Section 4 describes the CDAP model validation coupled to PRONGHORN-SC.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Material Characterization Report of EBR II Mark IV Fuel Element

The focus of this report is the characterization of an unirradiated as-built fuel element from the Experimental Breeder Reactor II (EBR-II) Mark IV driver fuel design. The fuel in this element is a metallic uranium-zirconium alloy, and the cladding material is HT9 stainless steel. Both the metallic fuel and cladding materials are characterized, including chemical composition, grain size, morphology, phase composition, precipitate composition, crystallography, density, and hardness.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

A Review of Irradiation Damage and Effects in α-Uranium

Understanding irradiation damage and effects in α-uranium (α-U) is critical to modeling the behavior of U-based metallic fuels. The aim of this review is to address the renewed interest in U-based metallic fuels by examining the state-of-the-art knowledge associated with the effect of irradiation on the microstructure, dimensional changes, and properties of α-U. We critically review the research progress on irradiation-induced growth and swelling, the enhancement of plastic flow and superplasticity by irradiation, and the effect of irradiation on thermal and electrical properties of α-U. Finally, we outline the research directions that require advancements, specifically the need to carry out fundamental research on several of the less understood mechanisms of irradiation damage and effects in α-U.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Experimental assessment of antimony (Sb) in pure uranium for immobilizing fission product lanthanides

The use of fuel additives is one of the concepts to mitigate fuel cladding chemical interaction (FCCI) for metallic fuel because fission product lanthanides are expected to be immobilized by the additive. Antimony (Sb) has been discovered to be a good candidate in UZr fuel. The present study focuses on its mechanism for immobilization in pure uranium, U–4Sb alloy was fabricated to understand the Sb behavior, while U–4Sb–4Ce was fabricated to simulate the case when lanthanides are generated. Both of the as-cast and annealed samples were characterized by scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). U–Sb precipitates are formed in U–4Sb alloy, while U–Sb and Ce–Sb were found in U–4Sb–4Ce alloy, thermal exposure does not change the Sb-precipitation morphologies or chemical composition. Furthermore, diffusion couple tests between those alloys and cladding materials (Fe or HT9) under 650 °C for 500 h were performed and analyzed using SEM/EDS. Diffusion couple tests demonstrate the reaction between cladding and uranium, while no reaction between Sb-precipitations and cladding materials was found.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

SCALE 6.3.1 Radiation Source Terms and Shielding Analysis for a Postulated Sodium-Cooled Fast Reactor Accident Scenario

In support of the US Nuclear Regulatory Commission non–light-water reactor fuel cycle demonstration project, SCALE 6.3.1 capabilities for radiation source term and shielding calculations are demonstrated for scenarios in the sodium-cooled fast reactor (SFR) fuel cycle. A postulated accident scenario, which consists of a seismic event causing the refueling machine to fall and release a spent fuel assembly inside the containment building (CB), is analyzed in this paper. Radiation source terms were generated for a U/TRU-10Zr metal fuel assembly with a 16.5% initial transuranic waste content and a discharge burnup of approximately 95 GWd/tHM; source terms were also generated for a high-assay low-enriched uranium metal fuel assembly (U-10Zr) with a 16.5% initial enrichment and a discharge burnup of 149.74 GWd/tHM. These radiation source terms were then used to determine the dose rate inside the CB and near the outer surface of the CB for a range of spent fuel assembly cooling times. The dose rate produced by the analyzed SFR assemblies is similar to that produced by a typical pressurized water reactor assembly with a discharge burnup of 50 GWd/MTU. Ultimately, the validation of the source terms predicted for SFRs with SCALE will need to be demonstrated via the use of assay measurements.

Radulescu, Georgeta↗
DOE OSTI2023

Management of Alkali and Alkaline Earth Fission Products in Used Pyroprocessing Salt

Pyroprocessing of spent nuclear fuel (SNF) involves dissolving metallic fuel into a molten salt electrolyte (typically eutectic LiCl-KCl) and then preferentially depositing actinides onto inert cathodes. Subsequent operations include drawdown of residual actinides and lanthanides from the electrolyte prior to re-using the salt. The recovered actinides are recycled and the recovered lanthanides are disposed as waste. Alkali and alkaline earth metal fission products in the fuel, such as Cs, Sr and Ba, dissolve into the salt during electrorefining. The concentrations of these elements buildup over time in the molten salt electrolyte, which may change the freezing point. The radioactive decay of 137 Cs and 90 Sr (half life 30 and 29 years) generates significant heat and produces strong ionizing radiation fields (β and γ). The increasing heat load and radioactivity as these elements build up in the molten salt requires frequent replacement and disposal of the electrolyte salt. Alternatively, the salt can be treated to remove these and other elements and then recycled to the electrorefiner. An effective strategy to manage these alkali and alkaline earth metal fission products in the molten salt electrolyte would increase the efficiency of pyroprocessing and decrease the volume of salt waste requiring disposal. Alkali and alkaline earth metal fission products are extremely stable in molten salt as chlorides--even more stable than the LiCl-KCl eutectic base salt--making them challenging to remove. They are not removed during drawdown operations to recover residual actinides and lanthanides and a separate operation is required to sufficiently purify the salt for reuse. This work is focused on selecting a method for separating Cs, Sr and Ba from the salt recovered from the lanthanide drawdown operation prior to recycling the cleaned salt back to the electrorefiner. Not addressed in this work is the management of the waste stream produced by the separation. This report summarizes the issues to be addressed when developing removal strategies for cesium, strontium, and barium and reviews existing methods to identify suitable methods and any technological gaps in their application.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2000

Energetic Combustion Devices for Aerospace Propulsion and Power

Chemical reactions have long been the mainstay thermal energy source for aerospace propulsion and power. Although it is widely recognized that the intrinsic energy density limitations of chemical bonds place severe constraints on maximum realizable performance, it will likely be several years before systems based on high energy density nuclear fuels can be placed into routine service. In the mean time, efforts to develop high energy density chemicals and advanced combustion devices which can utilize such energetic fuels may yield worthwhile returns in overall system performance and cost. Current efforts in this vein are being carried out at NASA MSFC under the direction of the author in the areas of pulse detonation engine technology development and light metals combustion devices. Pulse detonation engines are touted as a low cost alternative to gas turbine engines and to conventional rocket engines, but actual performance and cost benefits have yet to be convincingly demonstrated. Light metal fueled engines also offer potential benefits in certain niche applications such as aluminum/CO2 fueled engines for endo-atmospheric Martian propulsion. Light metal fueled MHD generators also present promising opportunities with respect to electric power generation for electromagnetic launch assist. This presentation will discuss the applications potential of these concepts with respect to aero ace propulsion and power and will review the current status of the development efforts.

Litchford, Ron J.↗
DOE OSTI2020

Nd, SbNd and Sb 3 Nd 4 and their interactions with the cladding alloy HT9

Lanthanide fission products, such as neodymium, formed during the irradiation of metallic fuels are known to cause deleterious effects from chemical interactions occurring at the fuel-cladding interface; a phenomenon known as fuel-cladding chemical interaction (FCCI). The use of fuel-based additives that bind with the lanthanide elements within the fuel meat, alleviating their interactions at the fuel-cladding interface, is one potential method proposed to mitigate the FCCI phenomenon and extend the burnup potential of such metallic fuel systems. In this study, antimony (Sb) is evaluated as one such additive, and neodymium (Nd) is used to represent the lanthanides. A Sb-Nd alloy is fabricated, which consists of two intermetallic phases, SbNd and Sb 3 Nd 4 . Isothermal diffusion couple experiments are carried out at 675 °C for 24 h between Nd and the Fe-12Cr based HT9 cladding alloy. The results are compared against similar diffusion couple experiments carried out between the Sb-Nd alloy and also HT9. Inter-diffusion between Nd/HT9 diffusion couple is characterized and the phases Fe 17 Nd 5 and Fe 17 Nd 2 were found to form whereas no interactions were observed in the Sb-Nd/HT9 diffusion couple. The lack of compound forming tendencies between Fe, the primary alloying constituent of HT9, and SbNd is elucidated through density functional theory (DFT) calculations on enthalpy of mixing, aligning well with the experimental observations. Lastly, the strong binding of Nd with Sb appears to be favorable, alleviating Nd interactions with HT9 constituent elements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Assessment Approach to Advanced Fuel Models

This document constitutes completion of the NEAMS milestone M3MS-21IN0201016, which is titled: Assessment of advanced fuel improvements. In this report we present: (1) simulations of separate effects creep tests for uranium alloy and HT-9; (2) examples of standardizing and updating metallic fuel assessments to include the latest models and key output figures of merit, which is coordinated with LANL to better evaluate advanced models; (3) examples of how the FIPD database at ANL is integrated into metallic fuel assessment cases; and finally (4) documentation of fuel-specific figures of merit and the BISON review process for assessments with best practices for preparing and reviewing finite element simulations in the appendix.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

FY23 Status of Quality Assurance Plan for Out-of-Pile Test Data

The DOE Advanced Reactor Technology program has supported recovery and preservation of legacy metallic fuel data collected as part of the US fast reactor program, recognizing it as essential to development and licensing activities for advanced fast reactors. Databases were established as organized collections of experimental records and data generated from in-pile experiments at EBRII, FFTF, and TREAT as well as related out-of-pile examinations of irradiated fuels. The Out-of-Pile Transient Database (OPTD), includes records of over 150 out-of-pile furnace transient tests on metallic fuels conducted at Argonne’s Alpha-Gamma Hot Cell Facility to evaluate their transient performance and characterize fuel/cladding interaction. The database is accessible to registered users from US universities, laboratories, and nuclear industry. Because the data in OPTD has not been formally qualified, its applicability and ability to support licensing activities is limited. This report outlines progress and plans to quality assure data in OPTD, maximizing its impact for model validation and verification as well as qualification of fuels for safe and effective use in advanced reactor designs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Comparison of zirconium redistribution in BISON EBR-II models using FIPD and IMIS databases with experimental Post Irradiation Examination

The BISON code framework is utilized to model and analyze zirconium redistribution within UPuZr metallic fuels. The simulation results are compared against past experimental metallography data to validate the BISON code models. Various BISON models are implemented and compared to properly reflect the Zr present in past data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Mesoscale modeling of microstructure-dependent thermal conductivity in U-Zr fuels

In uranium-zirconium (U-Zr) based metallic fuels, different phases can form at different compositions and temperatures. Typically, lamellar δ-UZr 2 and α-U phases are the dominant microstructures in U-rich U-Zr alloys at temperatures below 880 K. In this work, a finite element method based mesoscale modeling technique is used to calculate the effective thermal conductivities of such heterogeneous microstructures, using the thermal conductivities of two individual phases and their interphase thermal resistance (Kapitza resistance) as input parameters. The Kapitza resistance between δ-UZr 2 and α-U is determined at different temperatures, which shows an approximately T 3 dependence in the temperature range between 300 and 800 K. In addition, the Kapitza resistance exhibits a strong dependence on the aspect ratio of the δ-UZr 2 phase. Further, an analytical model is therefore developed to quantify the effects of both temperature and δ-UZr 2 aspect ratio on the Kapitza resistance. Using this newly developed Kapitza resistance model, the effective thermal conductivities of a number of δ-UZr 2 + α-U heterogeneous microstructures in U-Zr alloys, including non-lamellar microstructures, can be estimated accurately.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Pros and Cons Analysis of HALEU Utilization in Example Fuel Cycles

The Systems Analysis and Integration campaign assessed the pros and cons of high-assay low-enriched uranium (HALEU) utilization in advanced reactors and associated fuel cycles. The assessment was done for three example fuel cycles at equilibrium states: once-through, limited recycle, and continuous recycle (CR) starting with HALEU. Front- and back-end fuel cycle parameters and the Levelized Cost of Fuel (LCF), which is the Levelized Cost of Electricity excluding reactor cost, of the three example fuel cycles were calculated using a single Analysis Example Reactor. The pros and cons of HALEU utilization were assessed by normalizing the fuel cycle parameters and LCF to a unit of electricity generation (GWe-year) and comparing them with a Basis of Comparison. In this study, a sodium-cooled reactor with sodium-bonded metallic fuel having a burnup of ~100 GWd/t was used as the Analysis Example Reactor because its technology readiness level is high, and the burnup and fuel enrichment are in the middle of those ranges of advanced reactor concepts that are under development. The current once-through Light Water Reactors (OT-LWRs) with <5% low-enriched uranium and 50 GWd/t burnup were used as the Basis of Comparison. In addition, a series of sensitivity analyses was conducted by varying burnup, enrichment, fuel forms, and reactor types to capture the design variations in two once-through Advanced Reactor Demonstration Program (ARDP) reactors, Natrium with sodium-free metallic fuel having a burnup of ~150 GW/t and Xe-100 with Tristructural-Isotropic (TRISO) pebble fuel having a burnup of ~168 GWd/t.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1982

Effects of simulated lightning on composite and metallic joints

The effects of simulated lightning strikes and currents on aircraft bonded joints and access/inspection panels were investigated. Both metallic and composite specimens were tested. Tests on metal fuel feed through elbows in graphite/epoxy structures were evaluated. Sparking threshold and residual strength of single lap bonded joints and sparking threshold of access/inspection panels and metal fuel feed through elbows are reported.

Howell, W. E.↗