SEARCH · Search NASA

Results for “MOMENTS OF INERTIA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1994

The determination of the mass and mean density of Enceladus from its observed shape

Application of limb-fitting methods to the 11 best Voyager 2 images of Enceladus has shown that the shape of this satellite is closely represented by a triaxial ellipsoid. The observed ratio of the differences of the principal axes F = (b - c)/(a - c) is 0.23 (sup +0.04 sub - 0.01), consisting with the value F = 0.23 expected for a synchronously rotating satellite in hydrostatic equilibrium. We also deduce from the Voyager observations, after allowing for limb topography, that the mean radius of the satellite is 249.4 +/- 0.2 km. For satellites of known mass, measurement of the size and shape leads to a determination of the satellite's mean density and moment of inertial. We have used this method to determine the moments of inertia of Mimas (1988) and Tethys (1991). Enceladus appears to be hydrostatically relaxed, making it an ideal candidate for this type of analysis. However, none of the Pioneer or Voyager spacecraft had a close encounter with this satellite and thus its mass is effectively unknown. Enceladus is trapped in a 2:1 orbit-orbit resonance with Dione, but the amplitudes of libration are too small to allow a useful mass determination. Using the observed shape alone, without any other assumptions other than that the satellite is in hydrostatic equilibrium at its present orbital radius, we place an upper bound on the mean density of 1.12 +/- 0.05 g/cu cm. Thus, the mean density of Enceladus is probably little more than that of water-ice and we conclude that this satellite is markedly deficient in rock. If the mass of a satellite is unknown, but the satellite is differentiated and has a deep mantle of known composition, then we show that measurement of the shape alone can lead to a determination of the satellite's mass, mean density, and moment of inertia. Application of this method to Enceladus, assuming that the satellite has a deep mantle of water-ice of density 0.93 g/cu cm, gives the result that the mean density of the satellite is 1.00 +/- 0.03 g/cu cm. This result fills the one remaining gap in our knowledge of the structure of the Saturnian satellite system. We now know the mean densities of all the primary Saturnian satellites in the sequence from the coorbital satellites, Janus and Epimetheus, through to the outer satellite Iapetus (the densities of the small, secondary satellites in Trojan-type orbits are still unknown). The Saturnian system possesses two striking features. (1) Because of significant porosity, the mean material densities of the satellites Janus, Epimetheus, and Mimas could be substantially greater than the apparent mean densities of these satellies. (2) The densities of the satellites are not correlated with their distances from the planet; in particular, the satellites Enceladus and Tethys have lower mean densities than their interior and exterior neighbors, Mimas and Dione. This may be the result of gross postformation redistribution of rock and ice, possibly due to satellite disruptions are suggested by Smith et al. (1982).

Dermott, Stanley F.↗

NASA NTRS1944

Experimental Verification of the Rudder-Free Stability Theory for an Airplane Model Equipped with Rudders Having Negative Floating Tendency and Negligible Friction

An investigation has been made in the Langley free-flight tunnel to obtain an experimental verification of the theoretical rudder-free stability characteristics of an airplane model equipped with conventional rudders having negative floating tendencies and negligible friction. The model used in the tests was equipped with a conventional single vertical tail having rudder area 40 percent of the vertical tail area. The model was tested both in free flight and mounted on a strut that allowed freedom only in yaw. Tests were made with three different amounts of rudder aerodynamic balance and with various values of mass, moment of inertia, and center-of-gravity location of the rudder. Most of the stability derivatives required for the theoretical calculations were determined from forced and free-oscillation tests of the particular model tested. The theoretical analysis showed that the rudder-free motions of an airplane consist largely of two oscillatory modes - a long-period oscillation somewhat similar to the normal rudder-fixed oscillation and a short-period oscillation introduced only when the rudder is set free. It was found possible in the tests to create lateral instability of the rudder-free short-period mode by large values of rudder mass parameters even though the rudder-fixed condition was highly stable. The results of the tests and calculation indicated that for most present-day airplanes having rudders of negative floating tendency, the rudder-free stability characteristics may be examined by simply considering the dynamic lateral stability using the value of the directional-stability parameter Cn(sub p) for the rudder-free condition in the conventional controls-fixed lateral-stability equations. For very large airplanes having relatively high values of the rudder mass parameters with respect to the rudder aerodynamic parameters, however, analysis of the rudder-free stability should be made with the complete equations of motion. Good agreement between calculated and measured rudder-free stability characteristics was obtained by use of the general rudder-free stability theory, in which four degrees of lateral freedom are considered. When this assumption is made that the rolling motions alone or the lateral and rolling motions may be neglected in the calculations of rudder-free stability, it is possible to predict satisfactorily the characteristics of the long-period (Dutch roll type) rudder-free oscillation for airplanes only when the effective-dihedral angle is small. With these simplifying assumptions, however, satisfactory prediction of the short-period oscillation may be obtained for any dihedral. Further simplification of the theory based on the assumption that the rudder moment of inertia might be disregarded was found to be invalid because this assumption made it impossible to calculate the characteristics of the short-period oscillations.

STABILITY- FAIRCHILD R2K-1↗

NASA NTRS1970

Inertia Tests of a 24 Foot Single Keel Parawing, Model 2

Mass moment of inertia tests for parawings in vacuum sphere

Summers, D. O.↗

NASA NTRS1987

Adaptive momentum management for large space structures

Momentum management is discussed for a Large Space Structure (LSS) with the structure selected configuration being the Initial Orbital Configuration (IOC) of the dual keel space station. The external forces considered were gravity gradient and aerodynamic torques. The goal of the momentum management scheme developed is to remove the bias components of the external torques and center the cyclic components of the stored angular momentum. The scheme investigated is adaptive to uncertainties of the inertia tensor and requires only approximate knowledge of principle moments of inertia. Computational requirements are minimal and should present no implementation problem in a flight type computer and the method proposed is shown to be effective in the presence of attitude control bandwidths as low as .01 radian/sec.

Hahn, E.↗

NASA NTRS1987

Adaptive momentum management for the dual keel Space Station

The report discusses momentum management for a large space structure with the structure selected configuration being the Initial Orbital Configuration of the dual-keel Space Station. The external torques considered were gravity gradient and aerodynamic torques. The goal of the momentum management scheme developed is to remove the bias components of the external torques and center the cyclic components of the stored angular momentum. The scheme investigated is adaptive to uncertainties of the inertia tensor and requires only approximate knowledge of principal moments of inertia. Computational requirements are minimal and should present no implementation problem in a flight-type computer. The method proposed is shown to be effective in the presence of attitude control bandwidths as low as 0.01 radian/sec.

Hopkins, M.↗

NASA NTRS1960

A Theoretical Study of the Angular Motions of Spinning Bodies in Space

A theoretical study was made of the angular motions of spinning bodies in space. The analysis was based on Euler's dynamic equations which were linearized and solved analytically. The results of the study are directly applicable only to spin-stabilized vehicles with constant moments of inertia and angular displacements not exceeding about 15 degrees. Simple analytical expressions were obtained which relate angular motions to spin-rate and inertia distributions for a given disturbance. Consideration was given to the effects produced by having artificial damping in the system. The study included numerical examples and comparisons of analytical solutions with machine solutions of exact dynamic equations. The analysis indicated that angular motions are sensitive to inertia distribution. In considering a rectangular-pulse pitching moment, it was found that the residual motion was very sensitive to the time at which the moment was removed. Artificial damping due to a perfect proportional control system seemed to be more advantageous to pencil-like configurations than to disk-like configurations.

Suddath, Jerrold H.↗

NASA NTRS1981

On the motion of a flexible shallow spherical shell in orbit

A mathematical model for the motion of a large, flexible shallow spherical shell in a circular orbit is presented. For small elastic displacements and attitude angles the linearized equations for the roll and yaw (out-of-plane) motions completely separate from the pitch (in-plane) and elastic motions. However, the pitch and only the axisymmetric elastic modes are seen to be coupled in the linear range. With the shell's symmetry axis following the local vertical, the structure undergoes a static deformation under the influence of gravity and inertia. Further, the pitch and roll motions are unstable due to the unfavorable moment of inertia distribution. A rigid lightweight dumbbell with heavy tip masses and connected to the shell at its apex by a spring loaded double gimbal joint is proposed to gravitationally stabilize the structure. It is noted that the dumbbell motion can excite only those elastic modes having one nodal diameter. A sensitivity study of the system response characteristics to the key system parameters is carried out.

Kumar, V. K.↗

NASA NTRS2015

Testing and Validation of the Dynamic Inertia Measurement Method

The Dynamic Inertia Measurement (DIM) method uses a ground vibration test setup to determine the mass properties of an object using information from frequency response functions. Most conventional mass properties testing involves using spin tables or pendulum-based swing tests, which for large aerospace vehicles becomes increasingly difficult and time-consuming, and therefore expensive, to perform. The DIM method has been validated on small test articles but has not been successfully proven on large aerospace vehicles. In response, the National Aeronautics and Space Administration Armstrong Flight Research Center (Edwards, California) conducted mass properties testing on an "iron bird" test article that is comparable in mass and scale to a fighter-type aircraft. The simple two-I-beam design of the "iron bird" was selected to ensure accurate analytical mass properties. Traditional swing testing was also performed to compare the level of effort, amount of resources, and quality of data with the DIM method. The DIM test showed favorable results for the center of gravity and moments of inertia; however, the products of inertia showed disagreement with analytical predictions.

moments of inertia↗

NASA NTRS1943

Requirements for Auxiliary Stiffeners Attached to Panels Under Combined Compression and Shear

Panels of aluminum alloy sheets, framed by side and end stiffeners, were subjected to combined loading by means of offset knife edges applying loads to top and bottom end plates with reacting forces against the end plates supplied by laterally acting rollers. The test specimens were 17S-T aluminum alloy shoots 0.040 inch thick in panels of 10-inch width and three different lengths (approximately 10, 26, and 30 inch). Data were obtained for the bowing of transverse and longitudinal ribs of rectangular cross section and varying depths mounted on one side of the sheet only, for several ratios of compression to shear loads. Limiting values of the moments of inertia were calculated from these measurements. The experimental values exceed the theoretical values given by Timoshenko for the case of simply supported sheets with uniformly distributed boundary stresses. The work reported includes measurements of the effective shear moduli of the nine test panels with and without ribs. These data are compared with values published by Lahdo and Wagner.

ALUMINUM ALLOYS, SHEET - ALCOA 17ST - STRENGTH↗

NASA NTRS1992

Gravity and topography

The paper summarizes the fundamental gravity field constants for Mars and a brief historical review of early determinations and current-day accurate estimates. These include the planetary gravitational constant, global figure, dynamical oblateness, mean density, and rotational period. Topographic results from data acquired from the 1967 opposition to the most recent, 1988, opposition are presented. Both global and selected local topographic variations and features are discussed. The inertia tensor and the nonhydrostatic component of Mars are examined in detail. The dimensionless moment of inertia about the rotational axis is 0.4 for a body of uniform density and 0.37621 if Mars were in hydrostatic equilibrium. By comparing models of both gravity and topography, inferences are made about the degree and depth of compensation in the interior and stresses in the lithosphere.

Esposito, P. B.↗

DOE OSTI2021

Understanding the Angular Momentum Evolution of T Tauri and Herbig Ae/Be Stars

We investigate a sample of six Herbig Ae/Be stars belonging to the Orion OB1 association, as well as 73 low-mass objects, members of the σ Orionis cluster, in order to explore the angular momentum evolution at early stages of evolution, and its possible connection with main-sequence Ap/Bp magnetic stars. Using FIES and HECTOCHELLE spectra, we obtain projected rotational velocities through two independent methods. Individual masses, radii, and ages are computed using evolutionary models, distance, and cluster extinction. Under the assumption that similar physical processes operate in both T Tauri and Herbig Ae/Be stars, we construct snapshots of the protostar’s rotation against mass during the first 10 Myr with the aid of a rotational model that includes a variable disk lifetime, changes in the stellar moment of inertia, a dipolar magnetic field with variable strength, and angular momentum loss through stellar winds powered by accretion. We use these snapshots, as well as the rotational data, to infer a plausible scenario for the angular momentum evolution. We find that magnetic field strengths of a few kilo-Gauss at 3 Myr are required to match the rotational velocities of both groups of stars. Models with masses between 2 M {sub ⊙} and 3 M {sub ⊙} display larger angular momentum values by a factor of ~3, in comparison to stars of similar spectral types on the main sequence. Even though some quantitative estimates on this dramatic decrease with age for Ap/Bp magnetic main-sequence stars are presented, the results obtained for the angular momentum evolution do not explain their low rotation rates.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

NASA NTRS2007

Evidence for a Past High-Eccentricity Lunar Orbit

The large differences between the Moon's three principal moments of inertia have been mystery since Laplace considered them in 1799. Here we present calculations that show how past high eccentricity orbits can account for the moment differences, represented by the low-order lunar gravity field and libration parameters. One of our solutions is that the Moon may have once been in a 3:2 resonance of the orbit period to spin-period, similar to Mercury's present state. The possibility of past high-eccentricity orbits suggests a rich dynamical history and may influence our understanding of the early thermal evolution of the Moon.

Garrick-Betthell, Ian↗

NASA NTRS1962

Use of an Inertia Sphere to Damp the Angular Motions of Spinning Space Vehicles

A theoretical study was made of a device which might be used to damp the angular motions of spin-stabilized space vehicles with constant moments of inertia. the device was assumed to consist of a rate gyro, a servo control, and a rotor mounted in a single gimbal. The investigation was conducted by considering the general equations of motion of the vehicle-damper system and noting that simplification would result if the damper had a spherical inertia distribution. Such a distribution was assumed thereafter, and a control command was defined so that the gimbal angle would be proportional to the angular velocity of the vehicle about the gimbal axis. The resulting equations were linearized, and the Routh-Hurwitz criterion was applied to determine the conditions for stability. The study included two numerical examples showing possible application of inertia-sphere rate dampers. The general conditions for stability were found to be feasible for practical applications. A simplified stability criterion covers a large class of practical problems.

SPHERE↗

NASA NTRS2018

Change of Inertia Tensor Due to a Severed Radial Boom for Spinning Spacecraft

Many spinning spacecraft have long, flexible, radial booms to carry science instrumentation. These radial booms often have low mass but contribute significantly to the spacecraft moment of inertia due to their length. There are historical cases where radial booms have been severed or have failed to deploy. This paper presents models for the center of mass (CM) and inertia tensor that account for variable boom geometry and investigates how the CM and inertia tensor change when a radial boom is severed.The CM and inertia tensor models presented here will be included in the Attitude Ground System (AGS) for the Magnetospheric Multiscale (MMS) mission. This work prepares the AGS to provide uninterrupted support in the event of a radial boom anomaly. These models will improve the AGS computations for spin-axis precession prediction, Kalman filter propagation for the definitive attitude, and mass property generation needed for the onboard control system. As an additional application, a method is developed for approximating the location on the boom where the break occurred based on the new models and readily observable attitude parameters.

Inertia↗

NASA NTRS2018

Change of Inertia Tensor Due to a Severed Radial Boom for Spinning Spacecraft

Sedlak, Joseph E.↗

DOE OSTI2023

Additive Manufacturing Case Study Test Report

Sandia National Labs collaborated with Oak Ridge National Laboratory on a case study examining additive manufacturing opportunities for Geothermal applications. The study focused on designing components with improved performance characteristics that cannot be fabricated conventionally. A rotor for a downhole motor was chosen based on the potential for improving its rotational dynamics. Topology optimization was used as a design method to reduce the rotational inertia of the part while preserving sufficient rotational stiffness to transmit the torque required for the drilling application. The optimization resulted in a nearly 50% reduction in polar moment of inertia while maintaining other desired performance characteristics. The design developed using the topology optimization approach was fabricated using additive manufacturing and cannot be fabricated conventionally.

15 GEOTHERMAL ENERGY↗

DOE OSTI2021

Additive Manufacturing Case Study

Geothermal technologies include an extremely wide range of products required for well construction, completion, production, intervention and surface energy conversion activities. Many of these products are geometrically complex, require multi-step and highly specialized fabrication processes, and are expensive due to the low production numbers typically associated with the geothermal market. These challenges along with the high temperature demands of the geothermal environment have also hindered the adoption of many tools routinely used in the oil & gas industry.Recent advancements in Additive Manufacturing (AM) materials of construction, build volumes and part quality have transitioned the technology from primarily cosmetic prototyping applications to the point where AM can be used to make production parts, even for the most demanding applications. These improved AM capabilities along with the inherent ability of AM to produce complex parts and, in some cases, geometries that cannot be manufactured using conventional casting, machining and joining fabrication approaches motivate an exploration of its potential to positively impact geothermal well construction and operations technologies.Sandia National Labs collaborated with Oak Ridge National Laboratory on a case study examining additive manufacturing opportunities for Geothermal applications. The study focused on designing components with improved performance characteristics that cannot be fabricated conventionally. A rotor for a downhole motor was chosen based on the potential for improving its rotational dynamics. Topology optimization was used as a design method to reduce the rotational inertia of the part while preserving sufficient rotational stiffness to transmit the torque required for the drilling application. The optimization resulted in a nearly 50% reduction in polar moment of inertia while maintaining other desired performance characteristics. The design developed using the topology optimization approach was fabricated using additive manufacturing and cannot be fabricated conventionally. This paper will discuss the design approach, performance improvements and manufacturing methods used to produce the part.

Polsky, Yarom↗

NASA NTRS2013

Next-Generation Maneuvering System with Control-Moment Gyroscopes for Extravehicular Activities Near Low-Gravity Objects

Looking ahead to the human exploration of Mars, NASA is planning for exploration of near-Earth asteroids and the Martian moons. Performing tasks near the surface of such low-gravity objects will likely require the use of an updated version of the Manned Maneuvering Unit (MMU) since the surface gravity is not high enough to allow astronauts to walk, or have sufficient resistance to counter reaction forces and torques during movements. The extravehicular activity (EVA) Jetpack device currently under development is based on the Simplified Aid for EVA Rescue (SAFER) unit and has maneuvering capabilities to assist EVA astronauts with their tasks. This maneuvering unit has gas thrusters for attitude control and translation. When EVA astronauts are performing tasks that require ne motor control such as sample collection and equipment placement, the current control system will re thrusters to compensate for the resulting changes in center-of-mass location and moments of inertia, adversely affecting task performance. The proposed design of a next-generation maneuvering and stability system incorporates control concepts optimized to support astronaut tasks and adds control-moment gyroscopes (CMGs) to the current Jetpack system. This design aims to reduce fuel consumption, as well as improve task performance for astronauts by providing a sti er work platform. The high-level control architecture for an EVA maneuvering system using both thrusters and CMGs considers an initial assessment of tasks to be performed by an astronaut and an evaluation of the corresponding human-system dynamics. For a scenario in which the astronaut orbits an asteroid, simulation results from the current EVA maneuvering system are compared to those from a simulation of the same system augmented with CMGs, demonstrating that the forces and torques on an astronaut can be significantly reduced with the new control system actuation while conserving onboard fuel.

Carpenter, Michele↗