Search NASA⌕ Search

SEARCH · Search NASA

Results for “Material flow analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Microfabrication of a Segmented-Involute-Foil Regenerator, Testing in a Sunpower Stirling Convertor and Supporting Modeling and Analysis

Under Phase II of a NASA Research Award contract, a prototype nickel segmented-involute-foil regenerator was microfabricated via LiGA and tested in the NASA/Sunpower oscillating-flow test rig. The resulting figure-of-merit was about twice that of the approx.90% porosity random-fiber material currently used in the small 50-100 W Stirling engines recently manufactured for NASA. That work was reported at the 2007 International Energy Conversion Engineering Conference in St. Louis, was also published as a NASA report, NASA/TM-2007-2149731, and has been more completely described in a recent NASA Contractor Report, NASA/CR-2007-2150062. Under a scaled-back version of the original Phase III plan, a new nickel segmentedinvolute- foil regenerator was microfabricated and has been tested in a Sunpower Frequency-Test-Bed (FTB) Stirling convertor. Testing in the FTB convertor produced about the same efficiency as testing with the original random-fiber regenerator. But the high thermal conductivity of the prototype nickel regenerator was responsible for a significant performance degradation. An efficiency improvement (by a 1.04 factor, according to computer predictions) could have been achieved if the regenerator been made from a low-conductivity material. Also the FTB convertor was not reoptimized to take full advantage of the microfabricated regenerator's low flow resistance; thus the efficiency would likely have been even higher had the FTB been completely reoptimized. This report discusses the regenerator microfabrication process, testing of the regenerator in the Stirling FTB convertor, and the supporting analysis. Results of the pre-test computational fluid dynamics (CFD) modeling of the effects of the regenerator-test-configuration diffusers (located at each end of the regenerator) is included. The report also includes recommendations for accomplishing further development of involute-foil regenerators from a higher-temperature material than nickel.

Ibrahim, Mounir B.↗
DOE OSTI2020

Epsilon Metal: A Waste Form for Noble Metals from Used Nuclear Fuel

Epsilon metal (e-metal) is the metallic phase that forms as inclusions at the grain boundaries in the UO2 fuel during reactor operation. This metal is composed of Pd, Mo, Rh, Ru, and Tc. These metallic inclusions are insoluble in strong acid and remnants of these metallic inclusions have been found in the UO2 matrix that remains from the natural reactors in Gabon that were active 1.8 billion years ago, therefore e-metal should be an excellent waste form for the immobilization of the long-lived isotopes 107Pd (6.5 ? 106 a) and 99Tc (2.13 ? 105 a), with 99Tc being the isotope of interest for repository performance. Therefore, the chemical durability of this potential waste form is assessed in this study. Typically, corrosion rates for metallic materials are measured electrochemically because they are quick, inexpensive, and can reveal the mechanism by which a metal corrodes, at least initially. However, in a repository the waste form would be subjected to slowly flowing water without an applied electrical potential over long time periods. Therefore, the corrosion rates of e-metal specimens were measured with both electrochemical tests and the single-pass flow-through test (SPFT). Potentiodynamic and potentiostatic polarization results suggest that a thin passive film exists on the alloy surface, which seems to be responsible for its high corrosion resistance. Additionally, X-Ray photoelectron spectroscopic results suggest that Pd oxides are significantly enriched in the passive film Results from the SPFT show that the dissolution rates were weakly dependent on pH. Only Mo and Re were found in solution and were used for the calculation of the dissolution rates. In general, the electrochemically determined corrosion rates agree reasonably well with the initial dissolution rate measured with the SPFT test, but they are about one or two orders of magnitude higher than the steady state rates. The causes for this discrepancy are discussed.

epsilon-metal, nuclear waste form, corrosion, sing↗
DOE OSTI2023

Scaling and Complexity of Stress Fluctuations Associated with Smooth and Jerky Flow in FeCoNiTiAl High-Entropy Alloy

Recent observations of jerky flow in high-entropy alloys (HEA) revealed a high role of self-organization of dislocations in their plasticity. The present work reports the first results of the investigation of stress fluctuations during plastic deformation of an FeCoNiTiAl alloy, examined in a wide temperature range covering both smooth and jerky flow. These fluctuations, which accompany the overall deformation behavior representing an essentially slower stress evolution controlled by the work hardening, were processed using complementary approaches comprising Fourier spectral analysis, refined composite multiscale entropy, and multifractal formalisms. The joint analysis at distinct scales testified that even a macroscopically smooth plastic flow is accompanied by nonrandom fluctuations, disclosing the self-organized dynamics of dislocations. Qualitative changes in such a fine-scale “noise” were found with varying temperature. The observed diversity is significant for understanding the relationships between different scales of plasticity of HEAs and crystal materials in general.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Bounds on the Rate-Dependent Plastic Flow of Tantalum up to 75 GPa

In this study we report on the continued development of thermodynamics-based analysis of shock waves propagation with the objective of extracting information related to materials strength at high strain rates and pressures. Building on previous results reported for peak stresses of 10 GPa and 25 GPa, we present a series of three-step gas-gun shock experiments designed to explore the pressure and strain rate dependence of plastic flow in polycrystalline tantalum. These experiments at nominal peak stresses of 50 GPa and 75 GPa show the irreversible deformation before pullback to be almost entirely confined to the shock loading, with negligible plastic relaxation on the post-shock plateau. We also add a reverse-ballistics shot at 25 GPa, which was designed to reveal the pullback response with negligible interference from free-surface effects. General thermodynamic considerations allow us to place bounds on the plastic behavior even for parts of the curve that change far too rapidly for the velocimetric time resolution of (conservatively) ~ 5 ns. To analyze the data, we found it necessary to substantially improve the interpolation/extrapolation scheme in order to improve its robustness, flexibility and range of applicability. We describe the new scheme based on splines, as well as an extension of free-surface corrections to the post-shock rarefaction waves. Reanalysis with the new scheme produces results essentially within the error bars previously reported, showing that the known systematic errors associated with free-surface effects are relatively inconsequential for determining thermodynamic paths.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1996

Fatigue response of perforated titanium for application in laminar flow control

The room temperature tensile and fatigue response of non-perforated and perforated titanium for laminar flow control application was investigated both experimentally and analytically. Results showed that multiple perforations did not affect the tensile response, but did reduce the fatigue life. A two dimensional finite element stress analysis was used to determine that the stress fields from adjacent perforations did not influence one another. The stress fields around the holes did not overlap one another, allowing the materials to be modeled as a plate with a center hole. Fatigue life was predicted using an equivalent MW flow size approach to relate the experimental results to microstructural features of the titanium. Predictions using flaw sizes ranging from 1 to 15 microns correlated within a factor of 2 with the experimental results by using a flow stress of 260 MPa. By using two different flow stresses in the crack closure model and correcting for plasticity, the experimental results were bounded by the predictions for high applied stresses. Further analysis of the complex geometry of the perforations and the local material chemistry is needed to further understand the fatigue behavior of the perforated titanium.

Johnson, W. Steven↗
DOE OSTI2021

Systems Analysis Approach to Polyethylene Terephthalate and Olefin Plastics Supply Chains in the Circular Economy: A Review of Data Sets and Models

The environmental and economic impacts of implementing a circular economy in plastic waste supply chains are not well understood. The proposed systems analysis framework assesses environmental, social, and economic impacts of plastic waste supply chains in a circular economy. The first objective of this article is to identify datasets, models and knowledge gaps associated with waste plastic supply chain processes, mainly in the U.S. Our literature review indicated that the best datasets exist for virgin plastic resin production, mechanical recycling, landfilling, and incineration, with materials recovery facility being intermediate, and with chemical recycling the lowest. The second objective of this article is to develop an illustrative application of the framework by conducting a preliminary systems analysis of PET bottles with closed-loop recycling. Here, the preliminary systems analysis of PET bottles utilized a linear programming optimization method. Our optimization model indicated that both chemical and mechanical recycling processes are needed to achieve a true circular economy of PET bottles with the least greenhouse gas emissions, specifically reductions of 24% when compared with the linear economy. Good quality and standardized life cycle assessment and techno-economic analysis studies are needed to better understand the environmental, economic, and social impacts of advanced sorting and chemical recycling technologies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1979

MANTLE: A finite element program for the thermal-mechanical analysis of mantle convection. A user's manual with examples

A finite element computer code for the analysis of mantle convection is described. The coupled equations for creeping viscous flow and heat transfer can be solved for either a transient analysis or steady-state analysis. For transient analyses, either a control volume or a control mass approach can be used. Non-Newtonian fluids with viscosities which have thermal and spacial dependencies can be easily incorporated. All material parameters may be written as function statements by the user or simply specified as constants. A wide range of boundary conditions, both for the thermal analysis and the viscous flow analysis can be specified. For steady-state analyses, elastic strain rates can be included. Although this manual was specifically written for users interested in mantle convection, the code is equally well suited for analysis in a number of other areas including metal forming, glacial flows, and creep of rock and soil.

Thompson, E.↗
DOE OSTI2023

Safeguards Facility Model for Lead-cooled and Gas-cooled Fast Reactors

Efforts have been underway for many years on the development of safeguards for fast neutron reactors. The efforts have been primarily for sodium-cooled fast reactors (SFRs) in cooperation with Japan, to properly implement these safeguards as the reactors are conceptualized and ultimately commercialized. The primary challenge to development of adequate safeguard approaches for fast reactors has been in understanding how to apply different aspects of safeguards when facilities widely vary from one type of fast reactor to another and is largely dependent on several key aspects of the specific reactor type. For this report, the following key areas were identified for further analysis to determine where Lead-cooled Fast Reactors (LFRs) and Gas-Cooled Fast Reactors (GCFR) fuel material flow and key measurement points would differ from previously studied SFR safeguards.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1970

Prediction of gas leakage of environmental control systems

Mathematical models of leakage configurations and various flow theories are presented with the substantive experimental test data to provide background material for future design and failure analysis. Normal-rate leakage and emergency, high-rate leakage are considered.

Jackson, J. K.↗
NASA NTRS1987

Laminate-Moisture-Analysis Computer Program

Diffusion and deleterious effects of moisture predicted. General One-Dimensional, One Material Moisture Analysis computer program developed to predict moisture gradient across composite laminate where moisture enters two surfaces and flows in direction between these surfaces. Designed to monitor flow of moisture in Space Shuttle Orbiter payload bay doors but applicable for general use. Program written in FORTRAN IV.

Martin, Ronald T.↗
NASA NTRS2013

Flutter Analysis of the Thermal Protection Layer on the NASA HIAD

A combination of classical plate theory and a supersonic aerodynamic model is used to study the aeroelastic flutter behavior of a proposed thermal protection system (TPS) for the NASA HIAD. The analysis pertains to the rectangular configurations currently being tested in a NASA wind-tunnel facility, and may explain why oscillations of the articles could be observed. An analysis using a linear flat plate model indicated that flutter was possible well within the supersonic flow regime of the wind tunnel tests. A more complex nonlinear analysis of the TPS, taking into account any material curvature present due to the restraint system or substructure, indicated that significantly greater aerodynamic forcing is required for the onset of flutter. Chaotic and periodic limit cycle oscillations (LCOs) of the TPS are possible depending on how the curvature is imposed. When the pressure from the base substructure on the bottom of the TPS is used as the source of curvature, the flutter boundary increases rapidly and chaotic behavior is eliminated.

Goldman, Benjamin D.↗
DOE OSTI2020

Dam-Break Flow Measurements of Liquid–Granular Mixtures in a Channelized Reservoir

Dam-break flows of granular materials exhibit a complex non-Newtonian rheology, which is strongly influenced by various factors, such as the characteristics of the granular material, the degree of initial compaction, and saturation level of the granular matrix. Specially adapted nonintrusive techniques are required to investigate these flows in the laboratory. This paper investigated the nonintrusive technique of image analysis. The methodologies used in the measurement of bulk flow parameters, such as flow depth, front velocity, and flow rate, and the extraction of detailed flow characteristics such as velocity profiles, were discussed in the context of a series of granular dam-break flow experiments. These experiments were performed under three types of initial conditions: dry, saturated (water filling the pore space), and submerged (a layer of saturated granular material submerged under water) using four types of granular materials—PET pellets, crushed walnut shells, urea, and sand—with grain sizes ranging from 200 μm to 2.9 mm. High-speed cameras were used to capture the evolution and local properties of the flow, such as velocity fields using particle image velocimetry (PIV). Bulk properties of the flow were obtained by tracking the surface profile of the granular matrix and the water table. The extracted profiles were used to measure the evolution of the volume of the granular matrix and the fluid phase separately upstream and downstream of the gate, which allowed measuring the dilatancy (increase in pore space). The study showed that the image analysis techniques are versatile and can be adapted to measure different flow parameters in a variety of granular flows to better understand and analyze their complex behavior. Finally, the advantages and drawbacks of each image analysis technique were discussed and best-practice recommendations were provided.

42 ENGINEERING↗
NASA NTRS1998

An Integrated Tool for the Coupled Thermal and Mechanical Analysis of Pyrolyzing Heatshield Materials

Materials that pyrolyze at elevated temperature have been commonly used as thermal protection materials in hypersonic flight, and advanced pyrolyzing materials for this purpose continue to be developed. Because of the large temperature gradients that can arise in thermal protection materials, significant thermal stresses can develop. Advanced applications of pyrolytic materials are calling for more complex heatshield configurations, making accurate thermal stress analysis more important, and more challenging. For non-pyrolyzing materials, many finite element codes are available and capable of performing coupled thermal-mechanical analyses. These codes do not, however, have a built-in capability to perform analyses that include pyrolysis effects. When a pyrolyzing material is heated, one or more components of the original virgin material pyrolyze and create a gas. This gas flows away from the pyrolysis zone to the surface, resulting in a reduction in surface heating. A porous residue, referred to as char, remains in place of the virgin material. While the processes involved can be complex, it has been found that a simple physical model in which virgin material reacts to form char and pyrolysis gas, will yield satisfactory analytical results. Specifically, the effects that must be modeled include: (1) Variation of thermal properties (density, specific heat, thermal conductivity) as the material composition changes; (2) Energy released or absorbed by the pyrolysis reactions; (3) Energy convected by the flow of pyrolysis gas from the interior to the surface; (4) The reduction in surface heating due to surface blowing; and (5) Chemical and mass diffusion effects at the surface between the pyrolysis gas and edge gas Computational tools for the one-dimensional thermal analysis these materials exist and have proven to be reliable design tools. The objective of the present work is to extend the analysis capabilities of pyrolyzing materials to axisymmetric configurations, and to couple thermal and mechanical analyses so that thermal stresses may be efficiently and accurately calculated.

Pronchick, Stephen W.↗
DOE OSTI2021

Evolution of Microstructure and Surface Characteristics of FeCrAl alloys when Subjected to Flow Boiling Testing

FeCrAl alloys are candidate materials for manufacturing accident-tolerant fuel (ATF) cladding intended for light water reactors to increase fuel reliability and safety during design-basis and beyond-design-basis accident scenarios. The evolution of the materials' surface characteristics, microstructure, and mechanical properties when exposed to the Critical Heat Flux (CHF) in flow boiling testing is crucial for safety analysis while providing insights into their thermal-hydraulic performance in nuclear reactors. After CHF, the surface chemistry of two FeCrAl alloys, APMT and C26M, was studied to understand their evolution at the early stage of high-temperature excursions in short time periods. The results indicated a thin layer composed of oxides and hydroxides of Al, Cr, and Fe with varying proportions at different depths in the layer, as indicated by X-ray photoelectron spectroscopy (XPS) and depth profiling. The cross-sections prepared by focused ion beam (FIB) revealed the growth of an oxide layer, in the range of 90-180 nm thick, on the alloys' surfaces. The evolution of the materials' surface chemistry also led to a noticeable post CHF excursion increase in their wettability, with a slight increase in roughness. Further, the investigation of the materials' mechanical properties indicated a modest increase in hardness by 10-15% as well as an increase in their yield strength, as evidenced by the microindentation and ring compression tests conducted before and after CHF testing. Scanning electron Microscopy (SEM) and X-ray diffraction (XRD) were used to investigate microstructural features of the materials and their changes after CHF treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2024

REDOTHERM (Redox Countercurrent Thermodynamic Limits Model) [SWR-24-88]

REDOTHERM is an open-source, MATLAB-based thermodynamic modeling framework developed to evaluate the performance of redox-active materials for water (H2O) and carbon dioxide (CO2) splitting. It includes models of all major unit operations and supports comparative analysis of different redox-active material candidates. The model is tailored for systems of moving oxide under a parallel/cocurrent flow (PF) and countercurrent flow (CF) configurations. Unvalidated mixed flow reactor (MFR, also known as CSTR) model is also included as an optional addition.

Lidor, Alon [National Renewable Energy Laboratory ↗
NASA NTRS1974

Metallurgical processing in space

Research in metallurgical processing to study the effects of reduced gravity started with Apollo 14 and advanced with Skylab. Experiments provided specimens for analysis which solidified while constrained and while freely floating, which contained a mixture of normally immiscible materials, demonstrated enhanced capillary flow, solubility and ordered growth of a directionally solidified eutectic. The smaller, equiaxed grain structure obtained in reduced gravity compared to the larger, elongated grains obtained in one gravity indicate a difference in convection due to gravity in constrained solidification. Freely floating nickel alloy specimens showing metallic gas evolution at low pressure and reduced gravity suggest reduced pressure reactions which cannot occur on earth even in high vacuum chambers due to the hydrostatic head in the molten metal. Directionally solidified eutectics showed fewer termination defects when grown in reduced gravity. These are a few of the differences observed due to reduced gravity which could have important consequences on the future of metallurgy. In this paper we attempt to correlate the results of several Skylab solidification experiments.

Mckannan, E. C.↗
NASA NTRS1980

Thermal energy storage systems using fluidized bed heat exchangers

A rotary cement kiln and an electric arc furnace were chosen for evaluation to determine the applicability of a fluid bed heat exchanger (FBHX) for thermal energy storage (TES). Multistage shallow bed FBHX's operating with high temperature differences were identified as the most suitable for TES applications. Analysis of the two selected conceptual systems included establishing a plant process flow configuration, an operational scenario, a preliminary FBHX/TES design, and parametric analysis. A computer model was developed to determine the effects of the number of stages, gas temperatures, gas flows, bed materials, charge and discharge time, and parasitic power required for operation. The maximum national energy conservation potential of the cement plant application with TES is 15.4 million barrels of oil or 3.9 million tons of coal per year. For the electric arc furnance application the maximum national conservation potential with TES is 4.5 million barrels of oil or 1.1 million tons of coal per year. Present time of day utility rates are near the breakeven point required for the TES system. Escalation of on-peak energy due to critical fuel shortages could make the FBHX/TES applications economically attractive in the future.

Weast, T.↗