Search NASASearch

SEARCH · Search NASA

Results for “Measurement Patterns”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Turbomachinery noise studies of the AiResearch QCGAT engine with inflow control

The AiResearch Quiet Clean General Aviation Turbofan engine was tested on an outdoor test stand to compare the acoustic performance of two inflow control devices (ICD's) of similar design, and three inlet lips of different external shape. Only small performance differences were found. Far-field directivity patterns calculated by applicable existing analyses were compared with the measured tone and broadband patterns. For some of these comparisons, tests were made with an ICD to reduce rotor/inflow disturbance interaction noise, or with the acoustic suppression panels in the inlet or bypass duct covered with aluminum tape to determine hard wall acoustic performance. The comparisons showed that the analytical expressions used predict many directivity pattern features and trends, but can deviate in shape from the measured patterns under certain engine operating conditions. Some patterns showed lobes from modes attributable to rotor/engine strut interaction sources.

Mcardle, J. G.

Antenna radiation patterns in the whistler wave regime measured in a large laboratory plasma

Antenna radiation patterns of balanced electric dipoles and shielded magnetic loop antennas are obtained by measuring the relative wave amplitude with a small receiver antenna scanned around the exciter in a large uniform collisionless magnetized laboratory plasma in the whistler wave regime. The boundary effects are assumed to be negligible even for many farfield patterns. Characteristic differences are observed between electrically short and long antennas, the former exhibiting resonance cones and the latter showing dipole-like antenna patterns along the magnetic field. Resonance cones due to small electric dipoles and magnetic loops are observed in both the near zone and the far zone. A self-focusing process is revealed which produces a pencil-shaped field-aligned radiation pattern.

Stenzel, R. L.

Analysis of radiation patterns of interaction tones generated by inlet rods in the JT15D engine

Interaction tones were intentionally generated by circumferential arrays of equally spaced rods that protrude radially from the inlet wall near the face of the 28-blade fan. Arrays of 28 and 41 rods, selected to give specific far field radiation properties, were tested. The expected properties were readily apparent in the measured radiation patterns. A more detailed analysis of the test data showed both the precision and limitations of the applied acoustic theory. Rods protruding 23 percent of the radius predominantly generated only lowest radial order modes, as expected. Measured and predicted radiation patterns were generally in good agreement. The agreement, however, depended on a significant degree of implied refraction due to inlet velocity gradients. Refraction, if present, would impact static-flight noise comparisons.

Heidmann, M. F.

Active Array Measurements using the Portable Laser Guided Robotic Metrology System

In this paper, we will discuss the impact of mounting structures on the installed performance of phased arrays. In particular, performance data for the Conformal, Lightweight Antennas for Aeronautical Communications Technology (CLAS-ACT) antenna will be presented. Performance data from a series of mounting configurations will show that null depth and location is particularly susceptible to change while the main beam steering angle remains relatively stable. In addition, the Portable Laser Guided Robotic Metrology (PLGRM) system will be discussed as a suitable instrument for measuring antenna patterns in complex or difficult locations that are challenging for traditional ranges. The PLGRM system was recently developed at the National Aeronautics and Space Administration's (NASA) Glenn Research Center (GRC) and deployed to measure in situ antenna patterns.

Piasecki, Marie

Active Array Measurements using the Portable Laser Guided Robotic Metrology System

In this paper, we will discuss the impact of mounting structures on the installed performance of phased arrays. In particular, performance data for the Conformal, Lightweight Antennas for Aeronautical Communications Technology (CLAS-ACT) antenna will be presented. Performance data from a series of mounting configurations will show that null depth and location is particularly susceptible while the main beam steering angle remain relatively stable. In addition, the Portable Laser Guided Robotic antenna range (PLGR) will be discussed as a suitable instrument for measuring antenna patterns in complex or difficult locations that are challenging for traditional ranges. The PLGR antenna range was recently developed at the National Aeronautics and Space Administration's (NASA) Glenn Research Center (GRC) and deployed to measure in situ antenna patterns.

Piasecki, Marie

Assimilation of TROPICS Radiance Data in Nasa Geos System and Impact Assessments Through Observing System Experiments

Since the first full-scale weather satellite Television Infrared Observation Satellite (TIROS)-1 was launched in 1960 to measure weather patterns from space, the number of satellites carrying various sensors to measure atmospheric properties has increased rapidly. Data from these meteorological satellites have been crucial to the advancement of the NWP forecasts. Especially, space-borne measurements of atmospheric temperature and moisture information provided by microwave sounders were reported to contribute most to positive impacts on global NWP forecasts. Developing and launching an operational weather satellite is a daunting and tremendously expensive mission that requires many years of planning, developments, and maintenance after the launch. Small satellites with low size, weight, and power requirements can reduce the cost associated with the construction and launch of large bus platforms and draw attention of several space agencies and weather technology companies that started investing their resources to develop small satellites and measure the potential benefits and weaknesses. The NASA Time-Resolved Observations of Precipitation structure and storm Intensity with a Constellation of Smallsats (TROPICS) mission is a constellation of small satellites carrying state-of-art microwave temperature and humidity sounders with 12 channels between 91 GHz and 205 GHz frequency. Currently five TROPICS cubsats, including TROPICS-pathfinder, are in space and provide the temperature and humidity data from space to the meteorological community. This study seeks to assess the potential impact that the constellation of TROPICS satellites may bring to the global NWP analysis and forecasts by assimilating all-sky TROPICS data and implementing observing system experiments (OSE) using the NASA GEOS system. Various evaluations metrics including forecast skills, fit to other observations such as radiosondes and microwave and infrared sounder are used. Along with the NWP impact assessment, the quality of the TROPICS data is evaluated by looking at observation minus forecast statistics in comparisons with other conventional satellite temperature and humidity sounders.

Min-Jeong Kim

Assimilation of TROPICS Radiance Data in NASA GEOS System and Impact Assessments Through Observing System Experiments

Since the first full-scale weather satellite Television Infrared Observation Satellite (TIROS)-1 was launched in 1960 to measure weather patterns from space, the number of satellites carrying various sensors to measure atmospheric properties has increased rapidly. Data from these meteorological satellites have been crucial to the advancement of the NWP forecasts. Especially, space-borne measurements of atmospheric temperature and moisture information provided by microwave sounders were reported to contribute most to positive impacts on global NWP forecasts. Developing and launching an operational weather satellite is a daunting and tremendously expensive mission that requires many years of planning, developments, and maintenance after the launch. Small satellites with low size, weight, and power requirements can reduce the cost associated with the construction and launch of large bus platforms and draw attention of several space agencies and weather technology companies that started investing their resources to develop small satellites and measure the potential benefits and weaknesses. The NASA Time-Resolved Observations of Precipitation structure and storm Intensity with a Constellation of Smallsats (TROPICS) mission is a constellation of small satellites carrying state-of-art microwave temperature and humidity sounders with 12 channels between 91 GHz and 205 GHz frequency. Currently five TROPICS cubsats, including TROPICS-pathfinder, are in space and provide the temperature and humidity data from space to the meteorological community. This study seeks to assess the potential impact that the constellation of TROPICS satellites may bring to the global NWP analysis and forecasts by assimilating all-sky TROPICS data and implementing observing system experiments (OSE) using the NASA GEOS system. Various evaluations metrics including forecast skills, fit to other observations such as radiosondes and microwave and infrared sounder are used. Along with the NWP impact assessment, the quality of the TROPICS data is evaluated by looking at observation minus forecast statistics in comparisons with other conventional satellite temperature and humidity sounders.

Min-Jeong Kim

Aperture excited dielectric antennas

The results of a comprehensive experimental and theoretical study of the effect of placing dielectric objects over the aperture of waveguide antennas are presented. Experimental measurements of the radiation patterns, gain, impedance, near-field amplitude, and pattern and impedance coupling between pairs of antennas are given for various Plexiglas shapes, including the sphere and the cube, excited by rectangular, circular, and square waveguide feed apertures. The waveguide excitation of a dielectric sphere is modeled using the Huygens' source, and expressions for the resulting electric fields, directivity, and efficiency are derived. Calculations using this model show good overall agreement with experimental patterns and directivity measurements. The waveguide under an infinite dielectric slab is used as an impedance model. Calculations using this model agree qualitatively with the measured impedance data. It is concluded that dielectric loaded antennas such as the waveguide excited sphere, cube, or sphere-cylinder can produce directivities in excess of that obtained by a uniformly illuminated aperture of the same cross section, particularly for dielectric objects with dimensions of 2 wavelengths or less. It is also shown that for certain configurations coupling between two antennas of this type is less than that for the same antennas without dielectric loading.

Crosswell, W. F.

Modes of vibration on sqaure fiberglass epoxy composite thick plate

The frequencies and nodal patterns of a square thick plate of unidirectional fiberglass epoxy composite are measured experimentally. The constituent material is transversely isotropic. The plate is transversely excited at the center of the upper face, its resonant frequencies in the frequency range of 3 kHz to 21.73 kHz are detected and the measured nodal patterns are sketched.

Williams, J. H., Jr.

Planned LMSS propagation experiment using ACTS: Preliminary antenna pointing results during mobile operations

An overview and a status description of the planned LMSS mobile K band experiment with ACTS is presented. As a precursor to the ACTS mobile measurements at 20.185 GHz, measurements at 19.77 GHz employing the Olympus satellite were originally planned. However, because of the demise of Olympus in June of 1991, the efforts described here are focused towards the ACTS measurements. In particular, we describe the design and testing results of a gyro controlled mobile-antenna pointing system. Preliminary pointing measurements during mobile operations indicate that the present system is suitable for measurements employing a 15 cm aperture (beamwidth at approximately 7 deg) receiving antenna operating with ACTS in the high gain transponder mode. This should enable measurements with pattern losses smaller than plus or minus 1 dB over more than 95 percent of the driving distance. Measurements with the present mount system employing a 60 cm aperture (beamwidth at approximately 1.7 deg) results in pattern losses smaller than plus or minus 3 dB for 70 percent of the driving distance. Acceptable propagation measurements may still be made with this system by employing developed software to flag out bad data points due to extreme pointing errors. The receiver system including associated computer control software has been designed and assembled. Plans are underway to integrate the antenna mount with the receiver on the University of Texas mobile receiving van and repeat the pointing tests on highways employing a recently designed radome system.

Rowland, John R.

A petabyte size electronic library using the N-Gram memory engine

A model library containing petabytes of data is proposed by Triada, Ltd., Ann Arbor, Michigan. The library uses the newly patented N-Gram Memory Engine (Neurex), for storage, compression, and retrieval. Neurex splits data into two parts: a hierarchical network of associative memories that store 'information' from data and a permutation operator that preserves sequence. Neurex is expected to offer four advantages in mass storage systems. Neurex representations are dense, fully reversible, hence less expensive to store. Neurex becomes exponentially more stable with increasing data flow; thus its contents and the inverting algorithm may be mass produced for low cost distribution. Only a small permutation operator would be recalled from the library to recover data. Neurex may be enhanced to recall patterns using a partial pattern. Neurex nodes are measures of their pattern. Researchers might use nodes in statistical models to avoid costly sorting and counting procedures. Neurex subsumes a theory of learning and memory that the author believes extends information theory. Its first axiom is a symmetry principle: learning creates memory and memory evidences learning. The theory treats an information store that evolves from a null state to stationarity. A Neurex extracts information data without a priori knowledge; i.e., unlike neural networks, neither feedback nor training is required. The model consists of an energetically conservative field of uniformly distributed events with variable spatial and temporal scale, and an observer walking randomly through this field. A bank of band limited transducers (an 'eye'), each transducer in a bank being tuned to a sub-band, outputs signals upon registering events. Output signals are 'observed' by another transducer bank (a mid-brain), except the band limit of the second bank is narrower than the band limit of the first bank. The banks are arrayed as n 'levels' or 'time domains, td.' The banks are the hierarchical network (a cortex) and transducers are (associative) memories. A model Neurex was built and studied. Data were 50 MB to 10 GB samples of text, data base, and images: black/white, grey scale, and high resolution in several spectral bands. Memories at td, S(m(sub td)), were plotted against outputs of memories at td-1. S(m(sub td)) was Boltzman distributed, and memory frequencies exhibited self-organized criticality (SOC); i.e., 'l/f(sup beta)' after long exposures to data. Whereas output signals from level n may be encoded with B(sub output) = O(-log(2)f(sup beta)) bits, and input data encoded with B(sub input) = O((S(td)/S(td-1))(sup n)), B(sup output)/B(sub input) is much less than 1 always, the Neurex determines a canonical code for data and it is a lossless data compressor. Further tests are underway to confirm these results with more data types and larger samples.

Bugajski, Joseph M.

PM 2.5 Concentrations over Major Metropolitan Regions Inferred from Airborne High Spectral Resolution Lidar Measurements Using Machine Learning Regression

We use measurements of near-surface aerosol backscatter, extinction, and depolarization acquired by four NASA Langley Research Center airborne High Spectral Resolution Lidars (HSRLs) to develop a machine learning regression methodology to infer PM2.5 concentrations at the surface and aloft. These airborne HSRL measurements were acquired over major metropolitan regions in the United States and Asia during more than 170 flights since 2010. Hourly surface PM2.5 measurements from the EPA air quality system and similar networks in other countries acquired within 10 km and 15 minutes of these near-surface HSRL measurements are used to train models that compute PM2.5 concentrations from the HSRL measurements. We examine several regression methods and find that exponential Gaussian Process algorithms consistently give the best performance in terms of the lowest root-mean-square (RMS) errors and the highest correlations. Model performance varies significantly depending on various combinations of HSRL aerosol measurements (e.g., aerosol backscatter, extinction, depolarization, backscatter color ratios, lidar ratios, aerosol optical thickness) and retrievals (e.g., mixed layer height, aerosol type) used in the regressions. Models that use near-surface measurements of aerosol backscatter and aerosol intensive properties such as depolarization, backscatter color ratio, and lidar ratio typically give the best performance with RMS errors around 4 mg/m3 and correlation coefficients above 0.9. HSRL measurements were often acquired when the aircraft flew systematic “raster-scan” patterns for several hours over these cities. These flight patterns enabled measurements of the spatial, temporal, and vertical variabilities in the distributions of aerosol backscatter and aerosol intensive properties and allowed us to derive the corresponding variabilities in PM2.5 concentrations. We present examples of such variabilities over urban areas in the United States as well as Asia. We describe also how the distribution of surface PM2.5 varies with aerosol type and use these retrievals to examine model simulations of surface PM2.5 in these metropolitan regions. We also discuss how this methodology may be applied to measurements from satellite lidars such as CALIOP on CALIPSO and ATLID on EarthCARE.

lidar

Development of test methods for scale model simulation of aerial applications in the NASA Langley Vortex Research Facility

As part of basic research to improve aerial applications technology, methods were developed at the Langley Vortex Research Facility to simulate and measure deposition patterns of aerially-applied sprays and granular materials by means of tests with small-scale models of agricultural aircraft and dynamically-scaled test particles. Interactions between the aircraft wake and the dispersed particles are being studied with the objective of modifying wake characteristics and dispersal techniques to increase swath width, improve deposition pattern uniformity, and minimize drift. The particle scaling analysis, test methods for particle dispersal from the model aircraft, visualization of particle trajectories, and measurement and computer analysis of test deposition patterns are described. An experimental validation of the scaling analysis and test results that indicate improved control of chemical drift by use of winglets are presented to demonstrate test methods.

Jordan, F. L., Jr.

Error analysis of image reconstruction by a synthetic aperture interferometric radiometer

An error analysis is presented for the image reconstruction algorithm currently employed by the electronically steered thinned array radiometer aircraft instrument. This instrument samples components of the Fourier transform of the brightness temperature distribution at 1.4 GHz. Sources of error are identified, including systematic offsets and stochastic noise in the measurements, errors in the interference pattern antenna calibration, multipath scattering from the antenna support structure, mutual coupling between nearby array elements, and variations in the antenna patterns of the array elements. These errors are shown to produce artifacts in the image which appear as 'streaks' running along the instrument flight line. Possible hardware corrections are discussed. These include a reduction in the profile of the antenna support structure and a decoupling of adjacent and other nearby array elements using corrugated 'skirts'. Also discussed are several image enhancement techniques which detect and correct for some of the streaking. These techniques include a renormalization of the interference patterns based on the measured element patterns, a perturbation based interpretation of image contrast, and a covariance analysis of noise present in the image.

Ruf, Christopher S.