Results for “Microstructure simulation” — Page 10

NASA NTRS2003

Ceramic Foams for TPS Applications

Ceramic foams have potential in many areas of Thermal Protection Systems (TPS) including acreage and tile leading edges as well as being suitable as a repair approach for re-entry vehicles. NASA Ames is conducting ongoing research in developing lower-density foams from pre-ceramic polymer routes. One of the key factors to investigate, when developing new materials for re-entry applications, is their oxidation behavior in the appropriate re-entry environment which can be simulated using ground based arc jet (plasma jet) testing. Arc jet testing is required to provide the appropriate conditions (stagnation pressures, heat fluxes, enthalpies, heat loads and atmospheres) encountered during flight. This work looks at the response of ceramic foams (Si systems) exposed to simulated reentry environments and investigates the influence of microstructure and composition on the material? response. Other foam properties (mechanical and thermal) will also be presented.

Stockpoole, Mairead↗

NASA NTRS2015

NASA's Nuclear Thermal Propulsion Project

Space fission power systems can provide a power rich environment anywhere in the solar system, independent of available sunlight. Space fission propulsion offers the potential for enabling rapid, affordable access to any point in the solar system. One type of space fission propulsion is Nuclear Thermal Propulsion (NTP). NTP systems operate by using a fission reactor to heat hydrogen to very high temperature (>2500 K) and expanding the hot hydrogen through a supersonic nozzle. First generation NTP systems are designed to have an Isp of approximately 900 s. The high Isp of NTP enables rapid crew transfer to destinations such as Mars, and can also help reduce mission cost, improve logistics (fewer launches), and provide other benefits. However, for NTP systems to be utilized they must be affordable and viable to develop. NASA's Advanced Exploration Systems (AES) NTP project is a technology development project that will help assess the affordability and viability of NTP. Early work has included fabrication of representative graphite composite fuel element segments, coating of representative graphite composite fuel element segments, fabrication of representative cermet fuel element segments, and testing of fuel element segments in the Compact Fuel Element Environmental Tester (CFEET). Near-term activities will include testing approximately 16" fuel element segments in the Nuclear Thermal Rocket Element Environmental Simulator (NTREES), and ongoing research into improving fuel microstructure and coatings. In addition to recapturing fuels technology, affordable development, qualification, and utilization strategies must be devised. Options such as using low-enriched uranium (LEU) instead of highly-enriched uranium (HEU) are being assessed, although that option requires development of a key technology before it can be applied to NTP in the thrust range of interest. Ground test facilities will be required, especially if NTP is to be used in conjunction with high value or crewed missions. There are potential options for either modifying existing facilities or constructing new ground test facilities. At least three potential options exist for reducing (or eliminating) the release of radioactivity into the environment during ground testing. These include fully containing the NTP exhaust during the ground test, scrubbing the exhaust, or utilizing an existing borehole at the Nevada National Security Site (NNSS) to filter the exhaust. Finally, the project is considering the potential for an early flight demonstration of an engine very similar to one that could be used to support human Mars or other ambitious missions. The flight demonstration could be an important step towards the eventual utilization of NTP.

Houts, Michael↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRS2017

Analyzing the Chemical and Spectral Effects of Pulsed Laser Irradiation to Simulate Space Weathering of a Carbonaceous Chondrite

Space weathering processes alter the chemical composition, microstructure, and spectral characteristics of material on the surfaces of airless bodies. The mechanisms driving space weathering include solar wind irradiation and the melting, vaporization and recondensation effects associated with micrometeorite impacts e.g., [1]. While much work has been done to understand space weathering of lunar and ordinary chondritic materials, the effects of these processes on hydrated carbonaceous chondrites is poorly understood. Analysis of space weathering of carbonaceous materials will be critical for understanding the nature of samples returned by upcoming missions targeting primitive, organic-rich bodies (e.g., OSIRIS-REx and Hayabusa 2). Recent experiments have shown the spectral properties of carbonaceous materials and associated minerals are altered by simulated weathering events e.g., [2-5]. However, the resulting type of alteration i.e., reddening vs. bluing of the reflectance spectrum, is not consistent across all experiments [2-5]. In addition, the microstructural and crystal chemical effects of many of these experiments have not been well characterized, making it difficult to attribute spectral changes to specific mineralogical or chemical changes in the samples. Here we report results of a pulsed laser irradiation experiment on a chip of the Murchison CM2 carbonaceous chondrite to simulate micrometeorite impact processing.

Thompson, M. S.↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

DOE OSTI2025

Holistic Microstructure Control Strategies in Photopolymerization‐Induced Phase Separation of Acrylate Systems

Open porous materials, known for their large surface area and interconnected structures, are essential in various applications, including batteries, ion exchange, catalysis, filtration, and electronic waste recycling. A critical aspect of the functionality of porous membranes is the precise control of pore size and morphology. Photopolymerization-induced phase separation (photo-PIPS) offers a convenient and versatile methods for creating porous structures. However, controlling the porous morphology remains challenging due to the complex interplay between thermodynamics, polymerization kinetics, and monomer structures, which makes it difficult to establish the relationship between processing conditions and resulting morphology in photo-PIPS. Herein, a physics-based phase-field model capable of generating and characterizing the microstructures of porous materials based on both average and localized features is developed. Using the phase-field simulations as test bed, the effects of polarity, light intensity, and curing temperature, as well as the previously unexplored roles of chain transfer agents and substrates, on the morphology of the resulting porous microstructure are investigated. Experiments are performed to verify the results predicted by the simulations. This work lays out a comprehensive guide for designing PIPS-derived porous microstructures and offers practical engineering strategies for tailoring microstructure-level topology and size of pores for application-specific needs.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Investigation of residual stress distribution in wire-arc directed energy deposited refractory molybdenum alloy utilizing numerical thermo-mechanical analysis and neutron diffraction method

Directed energy deposition (DED), a metal additive manufacturing (AM) technique, offers higher deposition rates and energy efficiency, making it suitable for fabricating components from refractory molybdenum alloys, such as molybdenum-titanium-zirconium (TZM). However, large thermal gradients and non-equilibrium thermal cycles in DED could generate high residual stress in the component, potentially deteriorating quality and performance. Thus, this study aims to investigate residual stress generation and its distribution in wire-arc DED of TZM thin-wall, utilizing thermo-mechanical analysis and high-fidelity neutron diffraction (ND) method. Two interpass temperatures (50°C and 200°C) have been considered to investigate their impact on residual stress formation. During experiments, in-situ thermal data has been recorded using thermocouples, which have been utilized for calibrating the thermal model. Thermocouple data shows a good agreement with the simulation results, having a difference of less than 10 %. Post-deposition part deformation has been observed, which is measured using a coordinate measuring machine, showing maximum values of 0.93 mm and 0.78 mm for interpass temperatures of 50°C and 200°C, respectively. Numerical predictions of distortion deviated by less than 15% from the experimental results. ND measurement and simulation results indicate that residual stress magnitude and evolution vary across the TZM deposits, revealing microstructural anisotropy in both conditions. Notably, lower interpass temperatures resulted in higher residual stresses, confirmed by experimental and simulation data. Further, this study demonstrated that an integrated experimental and thermo-mechanical analysis can potentially reveal the temperature history, part deformation, and residual stress formation in wire-arc DED TZM alloy.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Structure and mechanical properties of grain boundaries in molybdenum disulfide (MoS 2 )

Molybdenum disulfide (MoS 2 ) is a two-dimensional material widely used as a lubricant in many applications involving mechanical loading under a wide range of operating temperatures. Since many synthesis and processing techniques yield MoS 2 in its polycrystalline form, establishing grain boundary (GB) structure–property relations is key to designing MoS 2 microstructures with tailored properties. Here, we employ classical, reactive atomistic simulations to investigate the structure and mechanical behavior of a wide range of GBs in MoS 2 as a function of temperature. Using a bicrystal MoS 2 geometry, we characterize the atomic structure and calculate the energy of several low-angle GBs. Then, we simulate the tensile deformation behavior of MoS 2 bicrystals at several temperatures. Our results reveal that at temperatures above 100 K, the deformation of MoS 2 bicrystals is characterized by the nucleation of shear bands from GBs that grow, with subsequent loading, into the MoS 2 crystals. At low temperatures, the tensile deformation is characterized by the nucleation and propagation of deformation fronts, resulting in altered bond angles and bond lengths. Quantitative analysis reveals a decrease in the ultimate tensile stress and ultimate failure strain of MoS 2 bicrystals with the increase in temperature. Furthermore, our simulations of the mechanical behavior of metastable GBs reveal that the strength and ductility decrease with the increase in energy of these boundary structures. In broad terms, our work provides future avenues to employ GB engineering as a strategy to tailor the properties of MoS 2 microstructures.

Moore, Robert D. [Lehigh Univ., Bethlehem, PA (Uni↗

DOE OSTI2025

Mesoscale Modeling of Dislocation Cell Structure Evolution and Radiation-Induced Segregation in Additively Manufactured Austenitic Stainless Steel

Structural alloys under irradiation develop radiation-induced segregation (RIS) at point defect sinks, which lead to undesired changes in the alloy's properties. Additively manufactured austenitic stainless steels are expected to yield a distinct response to irradiation damage owing to their unique as-printed dislocation cell structure. In this talk, we present the development of a mesoscale model for dislocation cell structure evolution coupled with RIS using the MOOSE framework. The evolution of network dislocations within spatially distinct cells and cell walls are modeled using climb-mediated edge annihilation and generation processes. Starting with initial microstructures of as-printed non-equilibrium segregations at dislocation cell walls, our 2D and 3D simulations explore the effects of irradiation temperature, dose rate, dislocation sink bias, and specimen thickness on microstructure evolution. The results will be compared against experimental characterizations of in-situ and ex-situ ion-irradiated samples, and the implications of evolving cell structure on irradiation damage response will be discussed.

additive manufacturing↗

DOE OSTI2025

Mobility assessment of the BCC and carbide phases in the C-Nb, C-U and Nb-U systems

Uranium carbides with refractory metal additions are considered for Gen IV nuclear reactors and nuclear thermal propulsion as fuels for their high-temperature and corrosion resistant properties. Understanding kinetic effects that dictate microstructural evolution during fabrication and operating conditions is essential to advance technological development of these fuels. This work presents the development of an atomic mobility database for C-Nb-U systems based off available experimental data supported with ab-initio methods. The mobility assessments and uncertainty quantification (using Markov chain Monte Carlo) were conducted in the Kawin software. Carbon diffusion is considered dominant, as metal diffusion is much slower, with niobium diffusion being even slower and rate limiting than uranium metal. We provide a comprehensive and self-consistent thermo-kinetic database that is validated by diffusion couple simulations through Kawin. In conclusion, this enables prediction of microstructural and phase evolution critical for the development and lifetime assessment of next generation nuclear fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRSDate not supplied

Computational Investigation of Oxidative Etch Pitting in FiberForm and Its Impact on Material Properties

Oxidation-driven carbon erosion does not occur uniformly but rather through the development of localized etch pits at active surface sites. These active sites form due to atomic defects on the carbon surface, making them significantly more reactive than the surrounding, non-defective areas. As a result, these sites are the first to react during ablation, leading to their removal. This process creates new defects in neighboring atoms, increasing their reactivity and causing localized carbon removal around these active sites. In this way, the highly reactive defective areas serve as nucleation points for the formation and growth of etch pits, which can have adverse effects on structural integrity of FiberForm. To better understand how these etch pits impact the material properties of carbon fiber microstructures, we have developed a new capability within the direct simulation Monte Carlo (DSMC) framework to capture the etch pit formation process. This capability, integrated into the DSMC code SPARTA (Stochastic Parallel Rarefied-gas Time-accurate Analyzer), models material removal in the presence of active sites, leading to the formation of etch pits. The current work focuses on studying the effects of these etch pits on the material properties of FiberForm, a widely used base material in thermal protection systems (TPS). The microstructure of virgin FiberForm, obtained via X-ray microtomography, is imported into SPARTA to generate the ablated geometries with etch pits. These modified microstructures are then analyzed using the Porous Microstructure Analysis (PuMA) software to compute various material properties, including elasticity, thermal conductivity, and permeability. We investigate the variation of these properties due to the complex surface topology changes caused by etch pit formation. Additionally, we compare the effects of pitting with the conventional model of shrinking fibers, traditionally used to simulate the ablation of carbon structures. Significant differences emerge between the two approaches. Consequently, this physically realistic model of material removal through etch pit formation offers improved accuracy in predicting the degradation of carbon-based TPS during oxidation. It also provides insights into other mechanisms, such as spallation, where chunks of material are removed into the flow due to etch pit growth. Ultimately, this model enhances our understanding of failure modes in these materials during ablation.

PuMA↗

DOE OSTI2026

Inverse design of hypoeutectoid pearlite steel microstructures using a deep learning and genetic algorithm optimization framework

Goal-oriented microstructure design in metallic materials is a challenging task due to complex structure-property relationships. Traditional experimental and computational approaches are time-intensive and economically inefficient, limiting their applicability for large-scale design space exploration. Here, in this work, we propose an end-to-end framework that integrates deep learning models with genetic optimization to design microstructures with targeted mechanical properties. Deep learning models enable accurate forward design, while their integration with genetic optimization enables efficient inverse design within a few hours, compared to days or weeks using conventional finite element simulations. The framework combines experimental characterization and finite element modeling to analyze the influence of microstructural features on the mechanical behavior of hypoeutectoid steels. Data from both experiments and simulations are used to train the deep learning models. To demonstrate its effectiveness, we apply the framework to 0.63% carbon steel with proeutectoid ferrite and pearlite phases, commonly used in industrial applications. In this study, 2D microstructures were used for modeling, selected primarily for computational efficiency and to establish proof of concept. The framework successfully optimizes microstructures for targeted yield strength, ultimate strength, and stress concentration factors while significantly reducing computational time. Beyond hypoeutectoid steels, this scalable framework can be extended to other material systems and integrated with additive manufacturing, offering an efficient approach for accelerating microstructure design for specific engineering applications.

ConvLSTM↗

DOE OSTI2025

Assessment of Microstructure Prediction Capabilities for Powder Bed Fusion Stainless Steel 316

The Advanced Materials and Manufacturing Technologies program aims to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy. However, the characteristic process-structure-property relationships of additive manufacturing (AM) materials pose challenges for the qualification and certification of AM nuclear components. In particular, component-scale variations in microstructure and properties can be driven by localized changes in melt pool dynamics due to how process parameters interact with different part geometries. Computational modeling tools can play a crucial role in predicting and controlling this variability. This report presents final results on process modeling tools designed to predict microstructure variability in additively manufactured stainless steel 316 parts. It details the software packages and physical modeling approaches employed to simulate an AM component within an automated process modeling workflow. Results are demonstrated through comparisons between predicted microstructures and experimental measurements across various representative processing conditions. The report concludes by discussing identified challenges and future opportunities for connecting the developed simulation workflow with mechanics simulations for prediction of part performance.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Link statistics of dislocation network during strain hardening

Dislocations are line defects in crystals that multiply and self-organize into a complex network during strain hardening. The length of dislocation links, connecting neighboring nodes within this network, contains crucial information about the evolving dislocation microstructure. By analyzing data from Discrete Dislocation Dynamics (DDD) simulations in face-centered cubic (fcc) Cu, we characterize the statistical distribution of link lengths of dislocation networks during strain hardening on individual slip systems. Here, our analysis reveals that link lengths on active slip systems follow a double-exponential distribution, while those on inactive slip systems conform to a single-exponential distribution. The distinctive long tail observed in the double-exponential distribution is attributed to the stress-induced bowing out of long links on active slip systems, a feature that disappears upon removal of the applied stress. We further demonstrate that both observed link length distributions can be explained by extending a one-dimensional Poisson process to include different growth functions. Specifically, the double-exponential distribution emerges when the growth rate for links exceeding a critical length becomes super-linear, which aligns with the physical phenomenon of long links bowing out under stress. This work advances our understanding of dislocation microstructure evolution during strain hardening and elucidates the underlying physical mechanisms governing its formation.

Crystal plasticity↗

DOE OSTI2025

Design of a separate effects MiniFuel irradiation experiment investigating microstructure evolution in high burnup UO 2

The microstructural evolution of UO 2 fuel pellets during commercial operation in light water reactors (LWRs) is known to vary significantly across the pellet radius due to spatial variations in local temperature and burnup. The primary obstacle to extending LWR refueling cycles to 24-month intervals is the susceptibility of certain high burnup fuel microstructures to fuel fragmentation, relocation, and dispersal (FFRD) during a loss of coolant accident (LOCA). Although FFRD of the high burnup structure in the rim region of a pellet is well studied, the fine fragmentation that has been observed in a second region, near the midradius of the pellet (termed the “dark zone”) following mock LOCA testing of high burnup commercial fuel rods is less understood. This paper describes the design, analysis, and execution of a separate effects MiniFuel irradiation experiment that aims to identify the specific temperature and burnup regimes under which FFRD-susceptible dark zone microstructures form. The small disc specimens (3 mm diameter by ∼0.3 mm thick) enable more precise control of the relatively uniform temperature and burnup conditions. A total of 42 specimens were fabricated with typical LWR fuel densities (∼96%–98% of theoretical density) and grain sizes (∼12 μm) and are being irradiated over a range of temperatures (600°C–1000°C) and discharge burnups (50–72 MWd/kg-U) that bound the midradius region of high burnup LWR fuel. Fuel specimens with identical 235 U enrichments were inserted in two irradiation locations in the High Flux Isotope Reactor and are currently undergoing irradiation to further evaluate the impact of rate effects (fission rate, time at temperature) on the microstructural evolution. The fuel fabrication and the thermal and neutronic simulations used for designing the experiment are detailed in this paper. A secondary objective of the experiment is to observe fission gas release (FGR) under the various irradiation conditions, and this work provides first-order predictions of FGR from all fuel specimens. The insights gained from these experiments will inform future high burnup core designs that could minimize the formation of susceptible microstructures and ultimately enable 24-month refueling cycles while minimizing the fraction of the fuel susceptible to FFRD.

FFRD↗

DOE OSTI2025

Physics-Informed Machine Learning Model for Ceramic Matrix Composite Creep

A physics-informed recurrent neural network (RNN) based surrogate model is developed to emulate the nonlinear, time-dependent constitutive behavior of ceramic matrix composites (CMCs) driven by matrix damage and constituent creep at the microscale. Physics-informed constraints are introduced into the surrogate model through regularization to ground the prediction in physics and improve its predictive capabilities. Training data is generated using the high-fidelity generalized method of cells (HFGMC) approach which calls appropriate creep and damage models for each of the constituents. This coupling permits simulating the nonlinear behavior of CMCs based on constituent response at the microscale along with microstructural features such as fiber and porosity volume fraction and fiber radius. The microscale repeating unit cell is loaded under creep fatigue conditions to replicate the material loading experienced in a turbine engine. Therefore, the RNN-based surrogate model is tasked with predicting, as a function of variable input stress sequence, temperature, and microstructural features, the resulting strain history response while satisfying physical constraints related to creep rate, isochoric inelastic deformation, and strain energy density. The trained surrogate model is shown to effectively match the strain history over quantified distributions of microstructural features and relevant loading regimes and temperatures. Neural network based surrogate models can offer efficient alternatives to running computationally intensive multiscale material models to simulate the nonlinear response of large structural models. Therefore, the presented work provides evidence towards the feasibility of developing, training, and running such models for CMCs with complex microstructures, nonlinear time-dependent material response, and under non-monotonic loading conditions.

ceramic matrix composites↗