SEARCH · Search NASA

Results for “Module”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS2012

W-band Heterodyne Receiver Module with 27 K Noise Temperature

We present noise temperature and gain measurements of a W-band heterodyne module populated with MMIC LNAs designed and fabricated using 35nm InP HEMT process. The module has a WR-10 waveguide input. GPPO connectors are used for the LO input and the I and and Q IF outputs. The module is tested at both ambient (300 K) and cryogenic (25 K) temperatures. At 25 K physical temperature, the module has a noise temperature in the range of 27-45 K over the frequency band of 75-111 GHz. The module gain varies between 15 dB and 27 dB. The band-averaged module noise temperature of 350 K and 33 K were measured over 80-110 GHz for the physical temperature of 300 K and 25 K, respectively. The resulting cooling factor is 10.6.

heterodyne module↗

NASA NTRSDate not supplied

Towers: Critical Initial Infrastructure for the Moon, Such as a Power Module Support

Towers are an efficient structure commonly used to elevate systems against a gravity field, such as above the surface of a planet or the Moon. Towers can be used to elevate antennas, transmitters and sensors for communication, navigation, and observation infrastructure in support of surface operations. Near the Lunar poles, elevation of rotating solar panels enables nearly continuous panel illumination for solar power production despite the Sun remaining near the horizon year-round. Further, once technology is developed for tower assembly, this same technology can be extended to the assembly of a variety of structures including rocket blast containment shields, bridges, shelters, and habitats from either Earth-sourced or Lunar-sourced structural members. Environmental factors on the Lunar surface are vastly different than those found on Earth and have significant impact on the design of towers. Towers designed for the Lunar surface have no heritage nor Earth analog. The designs discussed herein are therefore breaking new ground creating a fundamentally new class of structures outside of current experience and intuition. The purpose of this paper is to: a) describe the unique environmental factors affecting tower design on the Lunar surface compared to Earth-based systems, b) evaluate two structural forms for the tower; telescoping tubes and an assembled truss, as well as c)provide recommendations on when each structural form is most suitable. A major contribution presented in the current paper is to provide parametric plots and supporting equations of mass and volume versus module power level and blanket height above the Lunar surface for the solar array application, to enable system level studies of optimum power module distribution and size. A secondary contribution are plots of the mass and volume of aluminum or structural glass required for assembled truss towers formed from Lunar derived structural members. An objective of achieving 1 MW of total power has been used to enable comparison of structural forms, because the total mass of solar arrays is consistent. It will be shown that for moderate module sizes, up to ~50 kW power modules, based on a telescoping tube tower have advantages, but for power modules from 50 kW to 200 kW an assembled truss tower can be created with half to one third of the tube tower mass. More significantly, when shipped from Earth, an assembled truss tower can be packed into 1/14th to 1/25th of the tube tower volume. Truss designs in the 100 kW to 200 kW range will be shown to be a favorable when assembled from either graphite-epoxy angles shipped from Earth or aluminum angles fabricated from Lunar materials. 50 kW towers are an attractive choice for both a telescoping or assembled tower with the solar arrays elevated 10 m above the Lunar surface, while increased solar array elevation favors 100 kW to 200 kW power modules.

assembly↗

NASA NTRS1975

A dynamic model for the time evolution of the modulated cosmic ray spectrum

A recently developed model predicts an energy dependent phase lag in the modulated cosmic ray density U(t) given by U(t) approximately equal to US (t - tau) where US is the solution to the Fokker-Planck equation under time independent conditions and tau is the average time spent by particles inside the modulating region. The delay times tau are functions of modulating parameters R (the radius of the modulating cavity), V (the solar wind velocity), and K (the effective average diffusion-coefficient which is a function of energy). This model is applied to predict the time evolution of the modulated cosmic ray proton spectrum over a simulated solar cycle. A modulation produced mostly by varying R over the solar cycle is less consistent with the observations.

Ogallagher, J. J.↗

NASA NTRS1976

Flexible, FEP-Teflon covered solar cell module development

Techniques and equipment were developed for the large scale, low-cost fabrication of lightweight, roll-up and fold-up, FEP-Teflon encapsulated solar cell modules. Modules were fabricated by interconnecting solderless single-crystal silicon solar cells and heat laminating them at approximately 300 C between layers of optically clear FEP and to a loadbearing Kapton substrate sheet. Modules were fabricated from both conventional and wraparound contact solar cells. A heat seal technique was developed for mechanically interconnecting modules into an array. The electrical interconnections for both roll-up and fold-up arrays were also developed. The use of parallel-gap resistance welding, ultrasonic bonding, and thermocompression bonding processes for attaching interconnects to solar cells were investigated. Parallel-gap welding was found to be best suited for interconnecting the solderless solar cells into modules. Details of the fabrication equipment, fabrication processes, module and interconnect designs, environmental test equipment, and test results are presented.

Rauschenbach, H. S.↗

NASA NTRS1978

ODIN system technology module library, 1972 - 1973

ODIN/RLV is a digital computing system for the synthesis and optimization of reusable launch vehicle preliminary designs. The system consists of a library of technology modules in the form of independent computer programs and an executive program, ODINEX, which operates on the technology modules. The technology module library contains programs for estimating all major military flight vehicle system characteristics, for example, geometry, aerodynamics, economics, propulsion, inertia and volumetric properties, trajectories and missions, steady state aeroelasticity and flutter, and stability and control. A general system optimization module, a computer graphics module, and a program precompiler are available as user aids in the ODIN/RLV program technology module library.

Hague, D. S.↗

NASA NTRS1980

US Coast Guard lightweight fire-fighting module

The U.S. Coast Guard Fire-fighting Module developed for the purpose of fighting fires in harbors and on ships is described. The module can be lifted by a dockside crane or helicopter and placed on the deck of a patrol boat or cutter for transportation to the scene of the fire. At the fire the module can be set up and put in operation by a crew of two in approximately fifteen minutes. Once in operation the module will deliver water to two fire nozzles at a pressure of 150 psi and a flow rate of 2000 gpm. Sufficient fuel is carried in the module for three hours of continuous operation. A record of the development of the fire fighting module is also presented.

Source record↗

NASA NTRS1980

Ocean wave-radar modulation transfer functions from the West Coast experiment

Short gravity-capillary waves, the equilibrium, or the steady state excitations of the ocean surface are modulated by longer ocean waves. These short waves are the predominant microwave scatterers on the ocean surface under many viewing conditions so that the modulation is readily measured with CW Doppler radar used as a two-scale wave probe. Modulation transfer functions (the ratio of the cross spectrum of the line-of-sight orbital speed and backscattered microwave power to the autospectrum of the line-of-sight orbital speed) were measured at 9.375 and 1.5 GHz (Bragg wavelengths of 2.3 and 13 cm) for winds up to 10 m/s and ocean wave periods from 2-18 s. The measurements were compared with the relaxation-time model; the principal result is that a source of modulation other than straining by the horizontal component of orbital speed, possibly the wave-induced airflow, is responsible for most of the modulation by waves of typical ocean wave period (10 s). The modulations are large; for unit coherence, spectra of radar images of deep-water waves should be proportional to the quotient of the slope spectra of the ocean waves by the ocean wave frequency.

Wright, J. W.↗

NASA NTRS1981

On the power spectral density of quadrature modulated signals

The conventional (no-offset) quadriphase modulation technique suffers from the fact that hardlimiting will restore the frequency sidelobes removed by proper filtering. Thus, offset keyed quadriphase modulation techniques are often proposed for satellite communication with bandpass hardlimiting. A unified theory is developed which is capable of describing the power spectral density before and after the hardlimiting process. Using the in-phase and the quadrature phase channel with arbitrary pulse shaping, analytical results are established for generalized quadriphase modulation. In particular MSK, OPSK or the recently introduced overlapped raised cosine keying all fall into this general category. It is shown that for a linear communication channel, the power spectral density of the modulated signal remains unchanged regardless of the offset delay. Furthermore, if the in phase and the quadrature phase channel have identical pulse shapes without offset, the spectrum after bandpass hardlimiting will be identical to that of the conventional QPSK modulation. Numerical examples are given for various modulation techniques. A case of different pulse shapes in the in phase and the quadrature phase channel is also considered.

Yan, T. Y.↗

NASA NTRS1981

Comparison of photovoltaic cell temperatures in modules operating with exposed and enclosed back surfaces

Four different photovoltaic module designs were tested to determine the cell temperature of each design. The cell temperatures were compared to those obtained on identical design, using the same nominal operating cell temperature (NOCT) concept. The results showed that the NOCT procedure does not apply to the enclosed configurations due to continuous transient conditions. The enclosed modules had higher cell temperatures than the open modules, and insulated modules higher than the uninsulated. The severest performance loss - when translated from cell temperatures - 17.5 % for one enclosed, insulated module as a compared to that module mounted openly.

Namkoong, D.↗

NASA NTRS1984

Block V module program

An outlined overview of this module program is given. Tables are given for the following characteristics: module power trend, packing factor trend, cell and circuit characteristics, module physical characteristics, electrical performance, cell efficiency trend, module efficiency trend and module cost trend. The principal improvements are larger modules and higher performance.

Smokler, M. I.↗

NASA NTRS1984

Flammability of photovoltaic modules

A series of Class B burning-brand tests were performed on experimental modules using high-temperature, back-surface materials to develop the technology base required to construct fire-ratable modules. Results indicate the existence of synergistic relationships between hydrocarbon encapsulation materials and the experimental module configurations that provide increased fire resistance. These configurations use Kapton, fiberglass, neoprene rubber, stainless-steel foil or aluminum foil as the back surface. Successful test results occur when the structural integrity of the module back surface is maintained. Test failures of these modules always occur for one of three reasons: the outermost back cover melts, rips, or is too porous. In each case flammable molten encapsulant, its gaseous byproducts, or both, penetrates the back surface of the module and bursts into flame. Future efforts to complete the technology base will concentrate on the spread-of-flame test, focusing on the more promising configurations identified in the initial series of tests.

Sugimura, R. S.↗

NASA NTRS1984

Status of high efficiency module design and fabrication

The status of an ongoing DOE program to develop an AM1 photoelectric module with 15 percent conversion efficiency at normal heating temperatures, is reviewed. Emphasis is given to the efforts of a private company to develop a high efficiency module which also has high durability in normal operating conditions. The main design options considered are: high efficiency modules; large area modules; and optimized module fabrication techniques. The design of an automatic system for encapsulating module stacks is described.

Nowlan, M. J.↗

NASA NTRS1985

Reliability and engineering of thin-film photovoltaic modules

Objectives were to: examine thin-film cell attributes that influence module performance and reliability, explore the lessons and applicability of crystalline-silicon module technology to thin-film modules, review the current status of thin-film module technologies, and identify problem areas and needed research. A major need is to separate the effects and resons for reversible degradatin from nonreversible degradation. Amorphous-silicon (a-Si) reliability investigations are focusing on exploratory research investigations, accelerated Arrhenius-type testing of a-Si cells, real-time outdoor exposure testing of a-Si cells, cell failure analysis, and failure mechanism research. Studies included the reduction in strength of glass by high temperature depositions on glass and laser scribing, encapsulation materials development needs, and the testing of modules. The new materials and processes in thin-film modules will require a delinquent reliability effort, including: establishment of mechanism-specific reliability goals; quantification of mechanism parameter dependencies; prediction of expected long-term degradation; identification of cost-effective solutions; and testing and failure analysis of trial solutions.

Royal, E. L.↗

NASA NTRS1985

Amorphous-silicon module hot-spot testing

Hot spot heating occurs when cell short-circuit current is lower than string operating current. Amorphous cell hot spot are tested to develop the techniques required for performing reverse bias testing of amorphous cells. Also, to quantify the response of amorphous cells to reverse biasing. Guidelines are developed from testing for reducing hot spot susceptibility of amorphous modules and to develop a qualification test for hot spot testing of amorphous modules. It is concluded that amorphous cells undergo hot spot heating similarly to crystalline cells. Comparison of results obtained with submodules versus actual modules indicate heating levels lower in actual modules. Module design must address hot spot testing and hot spot qualification test conducted on modules showed no instabilities and minor cell erosion.

Gonzalez, C. C.↗

NASA NTRS1986

Evaluation of an electronic scanner of pressure (ESOP) module

An electronic scanner of pressure (ESOP) module, developed by NASA Ames Research Center, was installed in a wind tunnel and evaluated over a 5-month testing period. The solid-state ESOP module has 48 miniature pressure transducers and a heater circuit to maintain a constant module temperature. During the wind tunnel test, the module was subjected to an environmental temperature range from 60 F to 104 F, and to considerable module vibration. Zero drift was within + or - 0.5 percent of full-scale output for 37 of the transducers, and was greater than 5.0 percent for four transducers. Pressure measurements from 12 transducers were compared with Scanivalve modules. The agreement of these measurements was considered to be good.

Smeltzer, D. B.↗

NASA NTRS1986

Electrochemical aging effects in photovoltaic modules

Leakage currents were experimentally measured in PV modules undergoing natural aging outdoors, and in PV modules undergoing accelerated aging in laboratory environmental chambers. The significant contributors to module leakage current were identified with a long range goal to develop techniques to reduce or stop module leakage currents. For outdoor aging in general, module leakage current is relatively insensitive to temperature fluctuations, but is very sensitive to moisture effects such as dew, precipitation, and fluctuations in relative humidity. Comparing ethylene vinyl acetate (EVA) and polyvinyl butyral (PVB), module leakage currents are much higher in PVB as compared to EVA for all environmental conditions investigated. Leakage currents proceed in series along two paths, bulk conduction followed by interfacial (surfaces) conduction.

Mon, G. R.↗

NASA NTRS1987

Investigation of a GaAlAs Mach-Zehnder electro-optic modulator

A GaAs modulator operating at 0.78 to 0.88 micron wavelength has the potential to be integrated with a GaAs/GaAlAs laser diode for an integrated fiber-optic transmitter. A travelling-wave Mach-Zehnder modulator using the electro-optic effect of GaAs and operating at a wavelength of 0.82 microns has been investigated for the first time. A four layer Strip-loaded ridge optical waveguide has been analyzed using the effective index method and single mode waveguides have been designed. The electro-optic effect of GaAs has also been analyzed and a modulator using the geometry producing the maximum phase shift has been designed. A coplanar transmission line structure is used in an effort to tap the potentially higher bandwidth of travelling-wave electrodes. The modulator bandwidth has been calculated at 11.95 GHz with a required drive power of 2.335 Watts for full intensity modulation. Finally, some preliminary experiments were performed to characterize a fabrication process for the modulator.

Materna, David M.↗

NASA NTRS1986

Multiple trellis coded modulation (MTCM)

A new trellis coded modulation technique, referred to as multiple trellis coded modulation wherein more than one channel symbol per trellis branch is transmitted and demonstrated. Simple two state trellis codes for symmetric MPSK and AM modulations, which can achieve 3 dB gain over uncoded modulation at very high signal-to-noise ratios without bandwidth expansion and without reduction in information bit rate have been found. The gain of the new trellis codes with respect to previously reported two state trellis codes is between 1 to 2 dB at very high signal-to-noise ratios, depending on the number of bits per hertz transmitted. These gains are achieved with no additional cost in complexity; while indeed additional computations per branch are needed for the multiple trellis coding scheme. This concept can be extended to higher number of states and other type of modulations; i.e., quadrature amplitude modulation.

Divsalar, D.↗