Results for “NOZZLE THRUST COEFFICIENT” — Page 10

NASA NTRS1982

Nozzle performance calibration and turbomachinery operational analysis of Turbo-Powered Simulators (TPS) for the NASA-Langley EET propulsion airframe integration investigation

The Boeing flight simulator chamber facility energy efficient transport (EET) propulsion/airframe integration investigation was tested. Two turbopowered simulators (TPS) were calibrated with four different nacelle configurations. Two nacelle configurations were calibrated on each TPS, each calibration simulating the full nozzle pressure ratio range encountered in a one atmosphere total pressure wind tunnel operating over a Mach number range from 0.70 to 0.90 Mach. The results of the calibration test are in the form of velocity and discharge coefficient which is used in determining the simulator thrust while the TPS is operating in the wind tunnel.

Rowe, R. K.↗

NASA NTRS2013

Supersonic Retropropulsion CFD Validation with Ames Unitary Plan Wind Tunnel Test Data

A validation study of Computational Fluid Dynamics (CFD) for Supersonic Retropropulsion (SRP) was conducted using three Navier-Stokes flow solvers (DPLR, FUN3D, and OVERFLOW). The study compared results from the CFD codes to each other and also to wind tunnel test data obtained in the NASA Ames Research Center 90 70 Unitary PlanWind Tunnel. Comparisons include surface pressure coefficient as well as unsteady plume effects, and cover a range of Mach numbers, levels of thrust, and angles of orientation. The comparisons show promising capability of CFD to simulate SRP, and best agreement with the tunnel data exists for the steadier cases of the 1-nozzle and high thrust 3-nozzle configurations.

Schauerhamer, Daniel G.↗

NASA NTRSDate not supplied

Study of a Plug Nozzle for Supersonic Aircraft Concepts

A plug nozzle with a cylindrical cowl is studied. The geometry is adopted following commercial supersonic aircraft concepts considered in an ongoing NASA program. For the given cowl, the plug geometry is varied that includes shapes developed by a numerical optimization study as well as porous plugs. Experimental data on noise and flow field are discussed with an eye for minimum noise at low nozzle pressure ratios (NPR2) representing landing and takeoff (LTO) conditions. NPR up to about 4.7 is covered in the experiments. Limited thrust data with accompanying numerical simulation results are also presented. Results show that a plug designed for optimum thrust at cruise is noisier while a plug designed for optimum thrust at LTO has less noise, throughout the NPR range covered. The results also show that a plug nozzle can generate transonic tones and excess broadband noise (EBBN) at lower NPR, apart from well-known screech tones and broadband shock associated noise (BBSN) at higher NPR. A long porous plug is found to effectively suppress all these aberrant noise components while suffering less than 1% loss in thrust coefficient.

Jets↗

NASA NTRSDate not supplied

Study of a Plug Nozzle for Supersonic Aircraft Concepts

A plug nozzle with a cylindrical cowl is studied. The geometry is adopted following commercial supersonic aircraft concepts considered in an ongoing NASA program. For the given cowl, the plug geometry is varied that includes shapes developed by a numerical optimization study as well as porous plugs. Experimental data on noise and flow field are discussed with an eye for minimum noise at low nozzle pressure ratios (NPR2) representing landing and takeoff (LTO) conditions. NPR up to about 4.7 is covered in the experiments. Limited thrust data with accompanying numerical simulation results are also presented. Results show that a plug designed for optimum thrust at cruise is noisier while a plug designed for optimum thrust at LTO has less noise, throughout the NPR range covered. The results also show that a plug nozzle can generate transonic tones and excess broadband noise (EBBN) at lower NPR, apart from well-known screech tones and broadband shock associated noise (BBSN) at higher NPR. A long porous plug is found to effectively suppress all these aberrant noise components while suffering less than 1% loss in thrust coefficient.

Jets↗

NASA NTRS1973

Design integration and noise studies for jet STOL aircraft. Task 7C: Augmentor wing cruise blowing valveless system. Volume 2: Small-scale development testing of augmentor wing critical ducting components

Augmentor wing ducting system studies conducted on a valveless system configuration that provides cruise thrust from the augmentor nozzles have shown that most of the duct system pressure loss would occur in the strut-wing duct y-junction and the wing duct-augmentor lobe nozzles. These components were selected for development testing over a range of duct Mach numbers and pressure ratios to provide a technical basis for predicting installed wing thrust loading and for evaluating design wing loading of a particular wing aspect ratios. The flow characteristics of ducting components with relatively high pressure loss coefficients were investigated. The turbulent pressure fluctuations associated with flows at high Mach numbers were analyzed to evaluate potential duct fatigue problems.

Runnels, J. N.↗

NASA NTRS1974

Effect of upper-surface blowing on static longitudinal stability of a swept wing

A low-speed wind-tunnel investigation was conducted on a sharp-edged 75 deg delta wing, to determine the effect of upper-surface blowing on static longitudinal stability characteristics. The model incorporated nozzles, located at 0.50 mean aerodynamic chord length, supplied by compressed air to provide blowing on the upper surface. A full span trailing-edge flap was also tested as an additional high-lift device. The angle of attack was varied from 0 to 24 deg for a range of thrust coefficients from 0 to 0.45. The results of the static force tests showed that favorable increments in static longitudinal stability and lift were obtained using upper-surface blowing.

Coe, P. L., Jr.↗

NASA NTRS1974

Lateral static and dynamic aerodynamic parameters of the Kestrel aircraft (XV-6A) extracted from flight data

Flight test data have been used to extract the lateral static and dynamic aerodynamic parameters of the Kestrel aircraft. The aircraft configurations included thrust-jet angles of 0 deg, 15 deg, and 30 deg, and the test Mach numbers were 0.43, 0.62, and 0.82. The results showed that most of the parameters varied linearly with trim normal-force coefficient. The directional stability parameter showed a small increase with increasing trim normal-force coefficient and also with nozzle deflection. The effective-dihedral parameter, the damping-in-roll parameter, and damping-in-yaw parameter all increased (became more negative) with increasing trim normal-force coefficient. For the latter three parameters, the effect of nozzle deflection was dependent on the trim normal-force coefficient.

Suit, W. T.↗

NASA NTRS1978

Calculation of the longitudinal aerodynamic characteristics of upper-surface-blown wing-flap configurations

An engineering method for predicting the longitudinal aerodynamic characteristics of wing-flap configurations with upper surface blowing (USB) was developed. Potential flow models were incorporated into the prediction method: a wing and flap lifting surface model and a jet wake model. The wing-flap model used a vortex-lattice to represent the wing and flaps. The wing had an arbitrary planform and camber and twist, and the flap system was made up of a Coanda flap and other flap segments of arbitrary size. The jet wake model consisted of a series of closely spaced rectangular vortex rings. The wake was positioned such that it was tangent to the upper surface of the wing and flap between the exhaust nozzle and the flap trailing edge. It was specified such that the mass, momentum, and spreading rates were similar to actual USB jet wakes. Comparisons of measured and predicted pressure distributions, span load distributions, and total lift and pitching-moment coefficients on swept and unswept USB configurations are included. A wide range of thrust coefficients and flap deflection angles were considered at angles of attack up to the onset of stall.

Mendenhall, M. R.↗

NASA NTRS1960

Transonic Performance Characteristics of Several Jet Noise Suppressors

An investigation of the transonic performance characteristics of several noise-suppressor configurations has been conducted in the Langley 16-foot transonic tunnel. The models were tested statically and over a Mach number range from 0.70 to 1.05 at an angle of attack of 0 deg. The primary jet total-pressure ratio was varied from 1.0 (jet off) to about 4.5. The effect of secondary air flow on the performance of two of the configurations was investigated. A hydrogen peroxide turbojet-engine simulator was used to supply the hot-jet exhaust. An 8-lobe afterbody with centerbody, short shroud, and secondary air had the highest thrust-minus-drag coefficients of the six noise-suppressor configurations tested. The 12-tube and 12-lobe afterbodies had the lowest internal losses. The presence of an ejector shroud partially shields the external pressure distribution of the 8-lobe after-body from the influence of the primary jet. A ring-airfoil shroud increased the static thrust of the annular nozzle but generally decreased the thrust minus drag at transonic Mach numbers.

Schmeer, James W.↗

NASA NTRS1975

Thrust chamber life prediction. Volume 1: Mechanical and physical properties of high performance rocket nozzle materials

Pertinent mechanical and physical properties of six high conductivity metals were determined. The metals included Amzirc, NARloy Z, oxygen free pure copper, electroformed copper, fine silver, and electroformed nickel. Selection of these materials was based on their possible use in high performance reusable rocket nozzles. The typical room temperature properties determined for each material included tensile ultimate strength, tensile yield strength, elongation, reduction of area, modulus of elasticity, Poisson's ratio, density, specific heat, thermal conductivity, and coefficient of thermal expansion. Typical static tensile stress-strain curves, cyclic stress-strain curves, and low-cycle fatigue life curves are shown. Properties versus temperature are presented in graphical form for temperatures from 27.6K (-410 F) to 810.9K (1000 F).

Esposito, J. J.↗

NASA NTRS1972

Advanced augmentor-wing research

Results of research on advanced augmentors are discussed. Research concerned with performance indicated that: (1) augmentors with lobe-type nozzles give higher thrust augmentation than those with slot-type primary nozzles; (2) the thrust of augmentor wings at forward speed is greater than that of internally blown flaps for the speed range of interest; and (3) the optimum augmentor geometry at forward speed may be different from the optimum static geometry. Analysis of augmentor-wing data shows that the data may be correlated by accounting for the augmentation and entrainment in defining a net thrust coefficient.

Aiken, T. N.↗

NASA NTRS1972

Advanced augmentor-wing research

Results of research on advanced augmentors are discussed. Research concerned with performance has indicated that: (1) augmentors with lobe-type nozzles give higher thrust augmentation than those with slot-type primary nozzles, (2) the thrust of augmentor wings at forward speed is greater than that of internally blown flaps for the speed range of interest, and (3) the optimum augmentor geometry at forward speed may be different from the optimum static geometry. Analysis of augmentor-wing data has shown that the data may be correlated by accounting for the augmentation and entrainment in defining a net thrust coefficient.

Aiken, T. N.↗

NASA NTRS1987

Comparison of two procedures for predicting rocket engine nozzle performance

Two nozzle performance prediction procedures which are based on the standardized JANNAF methodology are presented and compared for four rocket engine nozzles. The first procedure required operator intercedence to transfer data between the individual performance programs. The second procedure is more automated in that all necessary programs are collected into a single computer code, thereby eliminating the need for data reformatting. Results from both procedures show similar trends but quantitative differences. Agreement was best in the predictions of specific impulse and local skin friction coefficient. Other compared quantities include characteristic velocity, thrust coefficient, thrust decrement, boundary layer displacement thickness, momentum thickness, and heat loss rate to the wall. Effects of wall temperature profile used as an input to the programs was investigated by running three wall temperature profiles. It was found that this change greatly affected the boundary layer displacement thickness and heat loss to the wall. The other quantities, however, were not drastically affected by the wall temperature profile change.

Davidian, Kenneth J.↗

NASA NTRS1987

Comparison of two procedures for predicting rocket engine nozzle performance

Two nozzle performance prediction procedures which are based on the standardized JANNAF methodology are presented and compared for four rocket engine nozzles. The first procedure required operator intercedence to transfer data between the individual performance programs. The second procedure is more automated in that all necessary programs are collected into a single computer code, thereby eliminating the need for data reformatting. Results from both procedures show similar trends but quantitative differences. Agreement was best in the predictions of specific impulse and local skin friction coefficient. Other compared quantities include characteristic velocity, thrust coefficient, thrust decrement, boundary layer displacement thickness, momentum thickness, and heat loss rate to the wall. Effects of wall temperature profile used as an input to the programs was investigated by running three wall temperature profiles. It was found that this change greatly affected the boundary layer displacement thickness and heat loss to the wall. The other quantities, however, were not drastically affected by the wall temperature profile change.

Davidian, Kenneth J.↗

NASA NTRS1979

Wind-tunnel investigation of a large-scale VTOL aircraft model with wing root and wing thrust augmentors

Tests were conducted in the Ames 40 by 80 foot wind tunnel to determine the aerodynamic characteristics of a large-scale V/STOL aircraft model with thrust augmentors. The model had a double-delta wing of aspect ratio 1.65 with augmentors located in the wing root and the wing trailing edge. The supply air for the augmentor primary nozzles was provided by the YJ-97 turbojet engine. The airflow was apportioned approximately 74 percent to the wing root augmentor and 24 percent to wing augmentor. Results were obtained at several trailing-edge flap deflections with the nozzle jet-momentum coefficients ranging from 0 to 7.9. Three-component longitudinal data are presented with the agumentor operating with and without the horizontal tail. A limited amount of six component data are also presented.

Aoyagi, K.↗

NASA NTRSDate not supplied

The Challenges with Material Interfaces in a Nuclear Thermal Propulsion Engine Heat Exchanger

Nuclear Thermal Propulsion (NTP) technology is an enabling technology to send humans to Mars and for agile cis-lunar mobility. NTP systems operate by flowing a propellent through a nuclear reactor. The resulting heated propellent is expulsed through a nozzle to create thrust. A key component in an NTP engine is the heat exchange tubes located within the nuclear reactor. The heat exchange tubes must be able to operate structurally at temperatures up to 2900 K. Carbon-Carbon is a potential material choice for the heat exchange tubes as the material maintains structural integrity at high temperatures. To achieve desired propulsion performance, NTP engines operate at extreme temperatures. In the extreme environment, differences in material coefficients of thermal expansion must be taken into account to avoid potential reduction of engine performance or system failure. Identified potential problems and proposed solutions to material interface challenges in the material interfaces of the heat exchange tubes are discussed, along with lessons learned for future work on NTP engine designs.

Nuclear Thermal Propulsion↗

NASA NTRSDate not supplied

The Challenges with Material Interfaces in a Nuclear Thermal Propulsion Engine Heat Exchanger

Nuclear Thermal Propulsion (NTP) technology is an enabling technology to send humans to Mars and for agile cis-lunar mobility. NTP systems operate by flowing a propellent through a nuclear reactor. The resulting heated propellent is expulsed through a nozzle to create thrust. A key component in an NTP engine is the heat exchange tubes located within the nuclear reactor. The heat exchange tubes must be able to operate structurally at temperatures up to 2900 K. Carbon-Carbon is a potential material choice for the heat exchange tubes as the material maintains structural integrity at high temperatures. To achieve desired propulsion performance, NTP engines operate at extreme temperatures. In the extreme environment, differences in material coefficients of thermal expansion must be taken into account to avoid potential reduction of engine performance or system failure. Identified potential problems and proposed solutions to material interface challenges in the material interfaces of the heat exchange tubes are discussed, along with lessons learned for future work on NTP engine designs.

Nuclear Thermal Propulsion↗

NASA NTRS1993

Tracking flow features using overset grids

A method is proposed to use overset grid topology to track dynamic flow features. Features of interest such as moving shock waves and vortices are overset with relatively fine tracker grids. Solutions are computed on the various grids and information is exchanged at intergrid boundaries. A grid track-sensor variable such as pressure is used to track the position of the flow feature to be resolved. The tracker grid is moved to the position where the track-sensor variable has the desired value (generally a maximum or a minimum) and new interpolation coefficients are computed for information exchange across grid boundaries. Solutions are computed at the current location and time-step, and grid motion is brought into the solution via time metrics. The method is demonstrated by tracking a moving shock and vortices shed behind a circular cylinder. It is conjectured that the method would show significant benefits in resolving features such as wakes behind oscillating airfoils and trajectories of jets issuing from rotating nozzles as encountered during thrust-vectoring.

Chawla, Kalpana↗