Search NASA⌕ Search

SEARCH · Search NASA

Results for “Nonlinear approximation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Implicit finite-difference simulations of steady and unsteady transonic flows

Implicit methods for several fluid dynamic formulations have been developed and applied to steady-state and low-frequency transonic flows. The basic steps involved in the construction of implicit schemes include: selection of linearly stable accurate implicit difference operators, time-linearization of nonlinear terms, and approximate factorization of the implicit operators into easily solved systems of equations. The proposed schemes are found very efficient for the simpler formulations.

Ballhaus, W. F.↗
NASA NTRS1981

On eigensolutions for discontinuous liners in a duct containing uniform mean flow

Sound attenuation in a rectangular acoustically lined duct containing uniform mean flow is analytically investigated using the generalized Wiener-Hopf technique. Uniqueness of the solution is enforced for lined sections of the finite axial extent by imposing edge conditions at the liner interface. Possible edge conditions are considered, including the Kutta condition, and the causal solution corresponding to edge conditions is considered the best choice. Solution methods such as the mode matching and singularity methods imply differing edge conditions, and results show that power attenuation is insensitive to the imposed edge conditions, although significant differences are observed for the reflection coefficient. The amplitude of the exponentially increasing instability mode in the lined section must be set to zero as a first approximation to the nonlinear situation, and results indicate that measurements of the reflection factor can be used to make a more definite decision about physically appropriate edge conditions.

Koch, W.↗
NASA NTRS1982

Numerical analysis of confined turbulent flow

The considered investigation is concerned with the development of an efficient computational method for obtaining a physical understanding of an internal turbulent field. The employed approach makes use of a 'two equation' type model for the turbulence to obtain the numerical solution of a two-dimensional confined turbulent flow. The mean flow governing equations are considered along with the governing equation of the mean temperature and concentrations, and the boundary conditions. The numerical procedure for solving the turbulent flow is discussed, taking into account an approximation to the nonlinear terms, and the inner and outer coupling. Attention is given to a stability convergence analysis, the stability characteristics, and computational examples.

Lin, A.↗
NASA NTRS1982

Unsymmetrically laminated composites

Classical lamination theory predicts that the room-temperature shapes of all elevated-temperature cure, unsymmetrically laminated composites are saddles. However, experimental observation indicates that the shapes are often cylindrical. In addition, a second cylindrical can sometimes be obtained from the first by a simple snap-through action. A geometrically nonlinear extension to classical lamination theory is used to explain this behavior. Approximate solutions to the nonlinear extension are obtained by using a Rayleigh-Ritz minimization of the laminate's total potential energy. A stability analysis explains the dual cylindrical shapes.

Hyer, M. W.↗
NASA NTRS1983

On the stellar rotation-activity connection

The relationship between rotation rates and surface activity in late-type dwarf stars is explored in a survey of recent theoretical and observational studies. Current theoretical models of stellar-magnetic-field production and coronal activity are examined, including linear kinematic dynamo theory, nonlinear dynamos using approximations, and full numerical simulations of the MHD equations; and some typical results are presented graphically. The limitations of the modeling procedures and the constraints imposed by the physics are indicated. The statistical techniques used in establishing correlations between various observational parameters are analyzed critically, and the methods developed for quasar luminosity functions by Avni et al. (1980) are used to evaluate the effects of upper detection bounds, incomplete samples, and missing data for the case of rotation and X-ray flux data.

Rosner, R.↗
NASA NTRS1986

Computation of turbulent pipe and duct flow using third order upwind scheme

The fully developed turbulence in a circular pipe and in a square duct is simulated directly without using turbulence models in the Navier-Stokes equations. The utilized method employs a third-order upwind scheme for the approximation to the nonlinear term and the second-order Adams-Bashforth method for the time derivative in the Navier-Stokes equation. The computational results appear to capture the large-scale turbulent structures at least qualitatively. The significance of the artificial viscosity inherent in the present scheme is discussed.

Kawamura, T.↗
NASA NTRS1989

Iterative procedures for space shuttle main engine performance models

Performance models of the Space Shuttle Main Engine (SSME) contain iterative strategies for determining approximate solutions to nonlinear equations reflecting fundamental mass, energy, and pressure balances within engine flow systems. Both univariate and multivariate Newton-Raphson algorithms are employed in the current version of the engine Test Information Program (TIP). Computational efficiency and reliability of these procedures is examined. A modified trust region form of the multivariate Newton-Raphson method is implemented and shown to be superior for off nominal engine performance predictions. A heuristic form of Broyden's Rank One method is also tested and favorable results based on this algorithm are presented.

Santi, L. Michael↗
NASA NTRS1992

Investigation of forced unsteady separated flows using velocity-vorticity form of Navier-Stokes equations

The phenomenon of forced unsteady separation and eruption of boundary-layer vorticity is a highly-complex, high-Reynolds number flow phenomenon, which abruptly leads to the formation of a dynamic stall vortex as demonstrated earlier by the authors for a NACA 0015 airfoil undergoing constant rate pitch-up motion. This, as well as the results of other researchers, have convincingly demonstrated a complex vortical structure within the state of unsteady separation prior to the evolution of dynamic stall. This phenomenon of vortex eruption, although observed in studying dynamic stall phenomena, is also associated with transition from laminar to turbulence flow and its generic nature has been stressed by many researchers including the present investigators. An unsteady Navier-Stokes (NS) analysis is developed for arbitrarily maneuvering bodies using velocity-vorticity variables; this formulation is nearly form-invariant under a generalized non-inertial coordinate transformation. A fully-implicit uniformly second-order accurate method is used, with the nonlinear convective terms approximated using a biased third-order upwind differencing scheme to be able to simulate higher-Re flows. No explicit artificial dissipation is added. The numerical method is fully vectorized and currently achieves a computational index of 7 micro-seconds per time step per mesh point, using a single processor on a CRAY Y-MP. The simulation results show that the energetic free shear from the leading edge is responsible for the wall viscous layer to abruptly erupt near the center of the counterclockwise rotating eddy in the unsteady boundary layer. Primary, secondary, tertiary and quaternary vortices have been observed before the dynamic stall vortex evolves and gathers its maximum strength. This study will discuss the simulation results of Reynolds number up to Re = 45,000 and will also discuss the efforts of initial acceleration in a specific maneuver, on the evolution of the stall vortex.

Ghia, K. N.↗
NASA NTRS1996

Analysis and Tests of Reinforced Carbon-Epoxy/Foam-Core Sandwich Panels with Cutouts

The results of a study of a low-cost structurally efficient minimum-gage shear-panel design that can be used in light helicopters are presented. The shear-panel design is based on an integrally stiffened syntactic-foam stabilized-skin with an all-bias-ply tape construction for stabilized-skin concept with an all-bias-ply tape construction for the skins. This sandwich concept is an economical way to increase the panel bending stiffness weight penalty. The panels considered in the study were designed to be buckling resistant up to 100 lbs/in. of shear load and to have an ultimate strength of 300 lbs/in. The panel concept uses unidirectional carbon-epoxy tape on a syntactic adhesive as a stiffener that is co-cured with the skin and is an effective concept for improving panel buckling strength. The panel concept also uses pultruded carbon-epoxy rods embedded in a syntactic adhesive and over-wrapped with a bias-ply carbon-epoxy tape to form a reinforcing beam which is an effective method for redistributing load around rectangular cutout. The buckling strength of the reinforced panels is 83 to 90 percent of the predicted buckling strength based on a linear buckling analysis. The maximum experimental deflection exceeds the maximum deflection predicted by a nonlinear analysis by approximately one panel thickness. The failure strength of the reinforced panels was two and a half to seven times of the buckling strength. This efficient shear-panel design concept exceeds the required ultimate strength requirement of 300 lbs/in by more than 100 percent.

Baker, Donald J.↗
NASA NTRS2007

NASA Langley's Approach to the Sandia's Structural Dynamics Challenge Problem

The objective of this challenge is to develop a data-based probabilistic model of uncertainty to predict the behavior of subsystems (payloads) by themselves and while coupled to a primary (target) system. Although this type of analysis is routinely performed and representative of issues faced in real-world system design and integration, there are still several key technical challenges that must be addressed when analyzing uncertain interconnected systems. For example, one key technical challenge is related to the fact that there is limited data on target configurations. Moreover, it is typical to have multiple data sets from experiments conducted at the subsystem level, but often samples sizes are not sufficient to compute high confidence statistics. In this challenge problem additional constraints are placed as ground rules for the participants. One such rule is that mathematical models of the subsystem are limited to linear approximations of the nonlinear physics of the problem at hand. Also, participants are constrained to use these models and the multiple data sets to make predictions about the target system response under completely different input conditions. Our approach involved initially the screening of several different methods. Three of the ones considered are presented herein. The first one is based on the transformation of the modal data to an orthogonal space where the mean and covariance of the data are matched by the model. The other two approaches worked solutions in physical space where the uncertain parameter set is made of masses, stiffnesses and damping coefficients; one matches confidence intervals of low order moments of the statistics via optimization while the second one uses a Kernel density estimation approach. The paper will touch on all the approaches, lessons learned, validation 1 metrics and their comparison, data quantity restriction, and assumptions/limitations of each approach. Keywords: Probabilistic modeling, model validation, uncertainty quantification, kernel density

Horta, Lucas G.↗
NASA NTRS1978

An advanced structural analysis/synthesis capability - ACCESS 2

An advanced automated design procedure for minimum weight design of structures (ACCESS 2) is reported. Design variable linking, constraint deletion, and explicit constraint approximation are used to effectively combine finite element and nonlinear mathematical programming techniques. The approximation concepts approach to structural synthesis is extended to problems involving fiber composite structure, thermal effects and natural frequency constraints in addition to the usual static stress and displacement limitations. Sample results illustrating these new features are given.

Schmit, L. A.↗
NASA NTRS1986

Solving Nonlinear Coupled Differential Equations

Harmonic balance method developed to obtain approximate steady-state solutions for nonlinear coupled ordinary differential equations. Method usable with transfer matrices commonly used to analyze shaft systems. Solution to nonlinear equation, with periodic forcing function represented as sum of series similar to Fourier series but with form of terms suggested by equation itself.

Mitchell, L.↗
NASA NTRSDate not supplied

Bayesian Symbolic Regression: Addressing Challenges in Estimating Fractional Bayes Factors and Application to Fatigue Crack Growth Modeling

This research pioneers advancements in computational mechanics by integrating Bayesian-based uncertainty quantification into symbolic regression, specifically focusing on the critical task of accurately estimating the fractional Bayes factor for selecting arbitrary equations. In our exploration, we rigorously study two prominent methods—sequential Monte Carlo and the Laplace approximation—employed for computing the fractional Bayes factor. Our findings underscore the limitations of the Laplace approximation, revealing its diminished accuracy in nonlinear and multimodal scenarios. Specifically, the Laplace approximation is shown to underpredict fractional Bayes factor on a wide set of equations associated with a symbolic regression benchmark. This comparative analysis sheds light on the nuanced performance of these techniques, guiding researchers toward more informed choices in uncertainty quantification within symbolic regression. Furthermore, we showcase the practical utility of these enhanced symbolic regression tools through their application to a real-world problem in fatigue crack growth modeling, emphasizing their efficacy in capturing the complexities of mechanical systems.

Geoffrey Bomarito↗
NASA NTRS1979

An evaluation of linear acoustic theory for a hovering rotor

Linear acoustic calculations are compared with previously reported data for a small-scale hovering rotor operated at high tip Mach numbers. A detailed calculated description of the distributions of blade surface pressure and shear stress due to skin friction is presented. The noise due to skin friction and loading, in the rotor disk plane, is small compared to thickness noise. The basic conclusions of Boxwell et al about the importance of nonlinear effects are upheld. Some approximations involved in the current theories for the inclusion of nonlinear effects are discussed. Using a model nonlinear problem, it is shown that to use the acoustic analogy, good knowledge of the flowfield is required.

Morris, C. E. K., Jr.↗
NASA NTRS1997

On the Role of Resonances in Nonradial Pulsators

Resonances or near resonances are ubiquitous among the excited nonradial pulsation modes of variable stars and they must play an important role in determining their pulsational behavior. Here in a first step at nonlinear asteroseismology, we explore some of the consequences of resonances by means of the amplitude equation formalism. We show how parity and angular momentum constraints can be used to eliminate many of the possible nonlinear resonant couplings between modes (and multiplets of modes), and how the amplitude equations can thus be simplified. Even when we may not be able, nor wish, to make an ab initio computation of the values of the coupling coefficients, it is still possible to obtain constraints on the nature of the excited modes if a resonance between observed frequencies can be identified. Resonances can cause nonlinear frequency locking of modes. This means that the observed frequencies appear in exact resonance even though the linear frequencies are only approximately in resonance. The nonlinear frequency lock, when it occurs, it does so over a range of departures from linear resonance, and it is accompanied by constant pulsation amplitudes. The locked, nonlinear frequencies can differ noticeably from their nonresonant counterparts which are usually used in seismology. This is particularly true for multiplets of modes split by rotation. Beyond the regime of the frequency lock, amplitude and frequency modulations can appear in the pulsations. Far from the resonance condition one recovers the regime of steady pulsations with nonresonant frequencies for which the seismological studies, as they are presently carried out, are justified (provided furthermore, of course, that nonlinear frequency shifts are negligible). Success in identifying a resonance in an observed power spectrum depends on the quality of the data. While keeping this limitation in mind, ew discuss the possible existence of peculiar resonances the pulsations specific variable white dwarfs and delta Scuti stars.

Buchler, J. R.↗