PLANNING FOR SEISMIC SHAKE TABLE TEST OF A FULL-SCALE DRY STORAGE OF SPENT NUCLEAR FUEL.
Abstract not provided.
Kalinina, Elena↗
SEARCH · Search NASA
Results for “Nuclear fuel testing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Large Plate Experiment of Chloride-induced Stress Corrosion Cracking in Spent Nuclear Fuel Storage Canisters
This report provides a description of the testing (in progress at the Savannah River National Laboratory) to evaluate the corrosion behavior of a large section of welded plate material harvested from the Sandia National Laboratories’ full-size mockup of a spent nuclear fuel (SNF) dry storage canister. The details of the establishment of this plate test, the interim corrosion results (from visual examination), and the general plan for examination of the plate in CY21 to evaluate crack growth behavior (if any) are provided. This work is intended to inform aging management programs for SNF canisters under conditions of extended dry storage. A “large plate” (approximately 51 x 46 cm with thickness 16 mm and weight about 30 kg) and containing a circumferential weldment from the mockup is the test specimen. The knowledge of the salt, temperature, humidity conditions for chloride-induced stress corrosion cracking (CISCC) including the threshold stress intensity factor, K iscc , were used to setup the large plate test in which a set of part-through-wall and through-wall electrical discharge machined (EDM) defects were positioned in the weld residual stress field of the welded plate material from the mockup canister. A marine salt solution was applied to this plate specimen with an air-brush spray, then dried, and then exposed to a sustained 71-73% RH condition at an ambient room temperature of 22 °C. The salt loading and environmental condition is expected to be aggressive to cause CISCC
12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
Advanced Thermal Simulator Testing: Thermal Analysis and Test Results
Work at the NASA Marshall Space Flight Center seeks to develop high fidelity, electrically heated thermal simulators that represent fuel elements in a nuclear reactor design to support non-nuclear testing applicable to the development of a space nuclear power or propulsion system. Comparison between the fuel pins and thermal simulators is made at the outer fuel clad surface, which corresponds to the outer sheath surface in the thermal simulator. The thermal simulators that are currently being tested correspond to a SNAP derivative reactor design that could be applied for Lunar surface power. These simulators are designed to meet the geometric and power requirements of a proposed surface power reactor design, accommodate testing of various axial power profiles, and incorporate imbedded instrumentation. This paper reports the results of thermal simulator analysis and testing in a bare element configuration, which does not incorporate active heat removal, and testing in a water-cooled calorimeter designed to mimic the heat removal that would be experienced in a reactor core.
Bragg-Sitton, Shannon M.↗
Electrochemical Methods for the Nuclear Fuel Cycle
This poster covers the design and testing of a 3-section electrochemical cell and goes over feasibility of refining uranium from molten salts.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Assessment of the BISON Metallic Fuel Performance Models
The US Department of Energy is leading a project to design and construct a fast spectrum test reactor called the Versatile Test Reactor (VTR). The BISON nuclear fuel performance code will be used to model VTR driver fuel, including looking at the effects of differences between the VTR driver fuel element design and the legacy fuel designs and experiments on which it is based. Simulations will be conducted to help determine whether the design’s behavior and performance are properly understood and to assess the margins to cladding failure and fuel melting relative to those predicted for past metallic fuel experiments. These predictions are expected to streamline VTR design and operation by helping inform the VTR driver fuel element design and by providing supplemental information for the fuel design safety basis.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor
Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this paper are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.
Accident Tolerant Fuels↗
The Use of Immersion Rigs for High Temperature Hydrogen Exposure Testing Within the Nuclear Thermal Rocket Element Environmental Simulator (NTREES)
The Nuclear Thermal Rocket Element Environmental Simulator (NTREES) was designed to perform non-nuclear testing of nuclear thermal rocket (NTR) fuel elements and materials. NTREES can simulate the thermal hydraulic environment within an NTR and has been leveraged to provide critical information on component performance and material compatibility. NTREES has the ability to expose test articles to pressurized Hydrogen gas up to 1000 psig and 225 g/s. NTREES tests are operated in a deoxygenated environment of Nitrogen or Argon pressurized up to 1000 psig. NTREES simulates fission heat through induction heating powered by a 1.2 MW AC power supply, and NTREES has recorded temperatures exceeding 3700K. To perform hot Hydrogen exposure tests on materials more rapidly and earlier in the fuel development process, NTREES must be able to test small material samples on the order of 1 square inch in volume, individual fuel assembly subcomponents, and particle materials. To meet these needs, multiple testing rigs have been developed to immerse test specimens in hot Hydrogen, with each "immersion rig" varying in its capability of sample type and performance range in order to meet the broadest range of testing needs. Herein is a discussion of a selection of these “immersion rigs.”
Nuclear Thermal Propulsion↗
Analysis of Dust and Corrosion Witness Samples Recovered from SNF Dry Storage Systems, Maine Yankee, 2023
This report documents the results of a long-term (5.79 year) exposure of 4-point bend corrosion test samples in the inlet and outlet vents of four spent nuclear fuel dry storage systems at the Maine Yankee Independent Spent Fuel Storage Installation. The goal of the test was to evaluate the corrosiveness of salt aerosols in a realistic near-marine environment, providing a data set for improved understanding of stress corrosion cracking of spent nuclear fuel dry storage canisters. Examination of the samples after extraction showed minor corrosion was present, mostly on rough-ground surfaces. However, dye penetrant testing showed that no SCC cracks were present. Dust collected on coupons co-located with the corrosion specimens was analyzed by scanning electron microscopy and leached to determine the soluble salts present. The dust was mostly organic material (pollen and stellate trichomes), with lesser detrital mineral grains. Salts present were a mix of sea-salts and continental salts, with chloride dominating the anions, but significant amounts of nitrate were also present. Both corrosion samples and dust samples showed evidence of wetting, indicating entry of water into the vents. The results of this field test suggest that the environment at Maine Yankee is not highly aggressive, although extrapolation from the periodically wetted vent samples to the hot, dry, canister surface may be difficult. No stress corrosion cracks were observed, but minor corrosion was present despite high nitrate concentrations in the salts. These observations may help address the ongoing question of the importance of nitrate in suppressing corrosion and SCC.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Pellet Cladding Interaction In-Reactor Ramp Testing in a World without the Halden Boiling Water Reactor
One of the most crucial performance areas for fuel rods in water cooled nuclear power plants is interaction between cladding tubes and fuel pellets. Experimental programs in test reactors have provided key data to help fuel developers and plant operators understand Pellet Cladding Interaction (PCI) phenomena and optimize their strategies for reliable fuel performance. Approximately 50 years of “ramp” testing programs, where the fission heating rate is deliberately manipulated in test rods, have been performed in a handful of test reactors to reveal and understand PCI behaviors such as iodine-assisted stress corrosion cracking. Unfortunately, the test reactors most engaged in this type of work have all been retired over the years up to the recent and unexpected closure of the Halden Boiling Water Reactor which effectively caused a hiatus in PCI ramp testing programs. The need for ramp testing is crucial at this time to enable refined PCI understanding as more plants consider implementing flexible operations, increased fuel rod burnup limits, and new fuel technologies with enhanced accident tolerance. This paper reviews some of the key PCI phenomena that must be addressed with in-pile testing and surveys past test reactor’s methods for achieving the needed conditions. A strategic approach is then presented using test reactors and complimentary facilities which are still available today. Near term data opportunities are put forth along with capability development strategies that will ensure future longevity in this field of research.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Raising Nuclear Thermal Propulsion (NTP) Technology Readiness Above 3
NTP development is currently supported by the NASA program office "Advanced Exploration Systems". The concept is a main propulsion option being considered for human missions to Mars in the 2030's. Major NTP development took place in the 1960's and 1970's under the Rover/NERVA program. The technology had matured to TRL 6 and was preparing to go to TRL 7 with a prototype flight engine before the program was cancelled. Over the last 40 years, a variety of continuations started, but only lasted a few years each. The Rover/NERVA infrastructure is almost all gone. The only remains are a few pieces of hardware, final reports and a few who worked the Rover/NERVA. Two types of nuclear fuel are being investigated to meet the current engine design specific impulse of 900 seconds compared to approximately 850 seconds demonstrated during Rover/NERVA. One is a continuation of composite fuel with new coatings to better control mid-band corrosion. The other type is a CERMET fuel made of Tungsten and UO2. Both fuels are being made from Rover/NERVA lessons learned, but with slightly different recipes to increase fuel endurance at higher operating temperatures. The technology readiness level (TRL) of these current modified reactor fuels is approximately TRL 3. To keep the development cost low and help mature the TRL level past 4 quickly, a few special non-nuclear test facilities have been made to test surrogate fuel, with depleted uranium, as coupons and full length elements. Both facilities utilize inductive heating and are licensed to handle depleted uranium. TRL 5 requires exposing the fuel to a nuclear environment and TRL 6 requires a prototype ground or flight engine system test. Currently, three different NTP ground test facility options are being investigated: exhaust scrubber, bore hole, and total exhaust containment. In parallel, a prototype flight demonstration test is also being studied. The first human mission to Mars in the 2030's is currently 2033. For an advanced propulsion concept to be seriously considered for use, the engine development plans need to show it is feasible and affordable to reach TRL 8 by 2027 and can be qualified for human mission use.
Gerrish, Harold P., Jr.↗
Integrating Advanced Modeling and Accelerated Testing for a Modernized Fuel Qualification Paradigm
With the increasing interest in sodium fast reactor technology, as seen by applications to the U.S. Nuclear Regulatory Commission for the OKLO Aurora plant, fuel testing for the TerraPower Traveling Wave Reactor, and the impending construction and startup of the versatile test reactor (VTR), a modernized, accelerated approach to fuel qualification is needed. To guide this effort, a Phenomena Identification Ranking Table–styled analysis was performed for a U-Pu-Zr sodium-free annular fuel system. This analysis evaluated a series of fuel design properties and parameters against their contributions to key fuel performance phenomena. The resulting priority parameters were then reviewed against existing modeling and experimental capabilities to support investigation of the highest-priority parameters. A pathway for qualification was then established using highthroughput, high-volume experiments from MiniFuel and FAST in parallel with advanced physics-based model development. This effort outlines how the first stages of qualification can be reduced from the typical 20+-year development cycle to 5 to 7 years by deploying accelerated irradiation testing platforms. As with any accelerated test, these methods are prototypic in some aspects and less so in others; however, by coupling with advanced fuel performance modeling and simulation capabilities, the larger space of irradiation parameters and material response provided offers advantages for the validation of physics-based models supporting the deployment of novel fuel designs. As a test case, this paper utilizes a proposed Mark II fuel system for the upcoming VTR. Thus, an accelerated qualification method can be tested for the development of MARK II driver fuel so that by the time of VTR startup, lead test assemblies for a Mark II fuel can be initiated.
73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
Refining Absorber Shroud Geometry to Maximize Power Output and Reduce Power Peaking in ATF Test Train
In the wake of the Fukushima Daiichi nuclear power plant accident in 2011, the accident tolerant fuels (ATF) program was initiated to enhance the safety of light-water reactor fuels, placing significant emphasis on cladding. A crucial step for the broad implementation of ATF in commercial reactors involves irradiation testing of the fuel designs. ATF-2D, the latest experiment in the ATF series, is slated to undergo irradiation in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). ATF-2D is a joint effort of the INL with industry partners General Electric Global Research; Framatome; General Atomics; the Japan Atomic Energy Agency; Hitachi-GE Nuclear Energy, Ltd; Global Nuclear Fuel-Japan Co., Ltd; Nippon Nuclear Fuel Development Co., Ltd; and Mitsubishi Heavy Industries, Ltd. The ATF-2D test train design consists of four tiers, each housing six rodlets. The device will be inserted in Loop 2A within the central flux trap of the ATR, and is anticipated to undergo irradiation throughout three 60-day cycles. Typical pressurized water reactor conditions will be emulated during the irradiation. The objective of the work presented here is to dimension neutron-absorbing hafnium (Hf) components surrounding the fuel rodlets, such that the axial power profile is flattened, while simultaneously ensuring that the total fission power output of the entire test train remains below 200 kW.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Refining Absorber Shroud Geometry to Maximize Power Output and Reduce Power Peaking in ATF Test Train
In the wake of the Fukushima Daiichi nuclear power plant accident in 2011, the accident tolerant fuels (ATF) program was initiated to enhance the safety of light-water reactor fuels, placing significant emphasis on cladding. A crucial step for the broad implementation of ATF in commercial reactors involves irradiation testing of the fuel designs. ATF-2D, the latest experiment in the ATF series, is slated to undergo irradiation in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). ATF-2D is a joint effort of the INL with industry partners General Electric Global Research; Framatome; General Atomics; the Japan Atomic Energy Agency; Hitachi-GE Nuclear Energy, Ltd; Global Nuclear Fuel-Japan Co., Ltd; Nippon Nuclear Fuel Development Co., Ltd; and Mitsubishi Heavy Industries, Ltd. The ATF-2D test train design consists of four tiers, each housing six rodlets. The device will be inserted in Loop 2A within the central flux trap of the ATR, and is anticipated to undergo irradiation throughout three 60-day cycles. Typical pressurized water reactor conditions will be emulated during the irradiation. The objective of the work presented here is to dimension neutron-absorbing hafnium (Hf) components surrounding the fuel rodlets, such that the axial power profile is flattened, while simultaneously ensuring that the total fission power output of the entire test train remains below 200 kW.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Final Seismic Shake Table Test Plan
The Spent Fuel Waste Disposition (SFWD) program is planning to conduct a full-scale seismic shake table test on the dry storage systems of spent nuclear fuel (SNF) to close the gap related to seismic loads on fuel assemblies in dry storage systems. This test will allow for quantifying the strains and accelerations on surrogate fuel assembly hardware and cladding during earthquakes of different magnitudes and frequency content. Full-scale testing is needed because a dry storage system is a complex and highly nonlinear system making it hard to predict (model) the responses to seismic excitations. The non-linearity arises from the multiple spatial gaps in the system – between fuel rods and the basket, between the basket and dry storage canister, between the dry storage canister and the storage cask (overpack), and ventilation gaps. The non-linearities pose significant limitations on the value of tests with scaled systems.
12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
A Corrosion Test Station for Improved Characterization and Examination Capabilities of Advanced Nuclear Reactor Fuels and Materials
Explore the source record for details and available documents.
Grimm, Terry↗
Photoluminescence in Tagging: A Glowing Review
This literature review explores the options of using photoluminescence for tagging uranium fuel and zirconium cladding in order to easily and quickly associate interdicted material to its facility of origin or pathway after loss of institutional control. Photoluminescence is the spontaneous emission of radiation by a substance when excited by interaction with light. The source of photoluminescence can be from organic, inorganic, and organometallic compounds. Each luminophore, or compound responsible for luminescent properties, has individual strengths and weaknesses, depending on the intended use. Many factors can affect the brightness, lifetime, color, and detectability of luminophores, such as humidity, temperature, oxygen availability, noise from radiation–induced luminescence, and the presence of quenching substances like iron. Application of luminescent compound to the surface of an item can be done using paint, dye, thin film, thick film, or electrochemical coating. Several of the application techniques may have secondary functions such as corrosion resistance and detection, heat resistance, protective properties, and more. When considering cladding, there are various successful studies on the application of luminescent coatings on zirconium. However, significant research will be necessary to explore which luminophore and which application technique would best fit the intended use. In order to proceed with this research, a baseline of the natural luminescence of the intended base material (nuclear fuel or cladding) is necessary. While there may be issues with background noise, quenching from the environment, quenching from the substrate, signal to noise weakness, etc. the multitude of options may make photoluminescent tagging an option. In summary, this review has demonstrated that photoluminescence is a potential option to tag nuclear fuel and cladding, but additional paper–studies, testing, and research is required to understand the compatibility of luminescent tags in nuclear reactor environments, manufacturability, and detectability.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Development and Standup Testing of a System to Observe Fission Gas Release During Transient Heating of Nuclear Fuel Element Segments
As part of an effort to increase the burnup of nuclear fuels used in Light Water Reactors, the mechanisms and timing of fission gas release during high temperature transients must be studied. In this work, a system was built to observe fission gas release of fuel element sections under evacuated conditions, at temperatures up to 800 °C. System capabilities and limitations are overviewed in this report. The system was further tested with a hydrogen-infused titanium foils and gas release was observed in agreement with literature observations. Pressure was monitored with two sensors, and temperature was monitored using a thermocouple and a pyrometer with continuous visual imaging.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Hot Hydrogen Testing of W-coated dUN Kernels for Nuclear Thermal Propulsion
Tungsten-coated kernels of uranium nitride (UN) are a possible reactor fuel component for nuclear thermal propulsion. Hot hydrogen testing of such kernels (approx. 250μm diameter, coating thickness 5μm) has been performed at temperatures from 1800°C to 2300°C for 30min each, using depleted uranium nitride (dUN). In addition to direct observations and mass loss measurements, the samples were analyzed by XRD and SEM/EDS after each run. Decomposition of dUN and the formation of molten uranium happened at all temperatures tested with reaction rates increasing with temperature, despite the tungsten coating. At 2300°C, the kernels disintegrated and molten uranium seeped through the wall and bottom of the tungsten crucible employed. These hot hydrogen tests allowed to test the integrity of the tungsten coating and addressed the operating limits of the loose tungsten-coated dUN kernels. Improved results are expected upon consolidation of the tungsten-coated dUN kernels in a Mo-W alloy matrix.
nuclear fuels↗