Results for “Operational Acceptability” — Page 10

NASA NTRS2016

Experimental Evaluation of Inlet Distortion on an Ejector Powered Hybrid Wing Body at Take-off and Landing Conditions

As part of the NASA Environmentally Responsible Aircraft project, an ultra high bypass ratio engine integration on a hybrid wing body demonstration was planned. The goal was to include engine and airframe integration concepts that reduced fuel consumption by at least 50% while still reducing noise 42 db cumulative on the ground. Since the engines would be mounted on the upper surface of the aft body of the aircraft, the inlets may be susceptible to vortex ingestion from the wing leading edge at high angles of attack and sideslip, and separated wing/body flow. Consequently, experimental and computational studies were conducted to collect flow surveys useful for characterizing engine operability. The wind tunnel tests were conducted at two NASA facilities, the 14- by 22-foot at NASA Langley and the 40- by 80-foot at NASA Ames Research Center. The test results included in this paper show that the distortion and pressure recovery levels were acceptable for engine operability. The CFD studies conducted to compare to experimental data showed excellent agreement for the angle of attacks examined, although failed to match the low speed experimental data at high sideslip angles.

Carter, Melissa B.↗

NASA NTRS2017

Airborne Trajectory Management (ABTM): A Blueprint for Greater Autonomy in Air Traffic Management

The aviation users of the National Airspace System (NAS) - the airlines, General Aviation (GA), the military and, most recently, operators of Unmanned Aircraft Systems (UAS) - are constrained in their operations by the design of the current paradigm for air traffic control (ATC). Some of these constraints include ATC preferred routes, departure fix restrictions and airspace ground delay programs. As a result, most flights cannot operate on their most efficient business trajectories and a great many flights are delayed even getting into the air, which imposes a significant challenge to maintaining efficient flight and network operations. Rather than accepting ever more sophisticated scheduling solutions to accommodate the existing constraints in the airspace, a series of increasingly capable airborne technologies, integrated with planned improvements in the ground system through the Federal Aviation Administration (FAA) Next Generation Air Traffic Management System (NextGen) programs, could produce much greater operational flexibility for flight path optimization by the aviation system users. These capabilities, described in research coming out of NASA's Aeronautics Research Mission Directorate, can maintain or improve operational safety while taking advantage of air and ground NextGen technologies in novel ways. The underlying premise is that the nation's physical airspace is still abundant and underused, and that the delays and inefficient flight operations resulting from artificial structure in airspace use and procedural constraints on those operations may not be necessary for safe and efficient flight. This article is not an indictment of today's NAS or the people who run it. Indeed, it is an exceptional achievement that Air Traffic Management (ATM) - the complex human/machine conglomeration of communications, navigation and surveillance equipment and the rules and procedures for controlling traffic in the airspace - has both the capacity and enables the degree of efficiency in air travel that it does. But it is also true that sixty years of the "radar religion" (i.e., reliance on radar-based command and control) has produced several generations of ATM system operators and researchers who believe that introducing automation within the existing functional structure of ATM is the only way to "modernize" the system. Even NextGen, which began as a proposal for "transformational" change in the way ATC is performed, has morphed over the last decade and a half to become just the inclusion of Global Positioning System (GPS) for navigation, Automatic Dependent Surveillance Broadcast (ADS-B) for surveillance, and Data Communications (Data Comm) for communications, while still operating in rigidly structured airspace with human controllers being responsible for separation and traffic flow management (TFM) within defined sectors of airspace, using the same horizontal separation standards that have been in use since raw primary radar was introduced in the 1950s. No system as massive as the current NAS ATM can be replaced with a better system while simultaneously meeting the transportation and other aviation needs of the nation. A new generation of more flexible operations must emerge and yet coexist in harmony with the current operation (i.e., share the same airspace without segregation), thereby enabling a long-term transformation to take place in the way increasing numbers of flights are handled. Market forces will be the ultimate driver of this transformation, and investment realities mandate that real benefits must accrue to the first operators to adopt these new capabilities. In fact, the kinds of missions envisioned in the emerging world of UAS operations, unachievable under conventional ATM, demand that this transformation take place. Airborne Trajectory Management (ABTM) is proposed as a series of transformational steps leading to vastly increased flexibility in flight operations and capacity in the airspace to accommodate many varied airspace uses while improving safety. As will be described, ABTM enables the gradual emergence of a new paradigm for user-based trajectory management in ATM that brings tangible benefits to equipped operators at every step while leveraging the air and ground investments of NextGen. There are five steps in this ABTM transformation.1 NASA has extensively studied the first and last of these steps, and a roadmap of increasing capabilities and benefits is proposed for bridging between these operational concepts.

Cotton, William B.↗

NASA NTRSDate not supplied

Initial Testing the Exploration Extravehicular Mobility Unit (xEMU) in Lunar Environment Simulation at the Neutral Buoyancy Lab (NBL) in 2022

Understanding how to effectively train for Extravehicular Activities (EVAs) for Artemis missions is critical. Tasked by the new Extravehicular Activity and Human Surface Mobility Program(EHP), a team of stakeholders from engineering and flight operations worked together to test the Exploration Extravehicular Mobility (xEMU) in the Neutral Buoyancy Lab(NBL) simulating the lunar environment. The NBL is a pool in which astronauts are typically trained to complete simulated International Space Station (ISS) EVA tasks in a neutral weigh-out. The overall focus for this test series was evaluating how well the NBL could be used as an effective simulated environment for Artemis lunar EVAs. New NBL support hardware was manufactured to support this test series and update the interfaces to be more representative of xEMU hardware such as a new NBL Portable Life Support System(PLSS)mock-up and umbilical, lights and cameras, and display and control unit (DCU).To simulate the 1/6th-gravity (1/6-g) environment, extra weights were added around the suit to create an accurate center of gravity representation. The Partial Gravity Weigh-out Stand (PGWS) predicted where and how much weight would be required for the 1/6th-G simulation and predicted the center of gravity placement. After the weigh-out attempt was completed, the suited participant would complete a set of directed tasks such as kneeling, object pick-up, and walking to evaluate the weigh-out. To create the lunar environment, sand, boulders, and ramps were added to the pool floor. If time allowed after weigh-out was determined acceptable, the flight operations team would direct the suited participants to complete simulated Artemis EVA tasks using flight-like tools and tool cart. The team also evaluated turning out the overhead lights in the NBL for a portion of some of the test runs and using a solar simulator to create amore realistic lunar south pole lighting environment. The test series completed one unmanned test and nine manned tests. With four of the tests, dual xEMU suited operations were completed with subjects in both the small and large xEMU sizes. Overall, the NBL was able to create an acceptable lunar landscape and ability to have two subjects work side by side in pressurized xEMUs which currently cannot be achieved in other test environments. Achieving a stable 1/6th-G lunar weigh-out and clear, consistent dual suit communications was a challenge for this series. Future work is planned to continue to improve this simulation environment.

spacesuit↗

NASA NTRSDate not supplied

Initial Testing of the Exploration Extravehicular Mobility Unit (xEMU) in Lunar Environment Simulation at the Neutral Buoyancy Lab (NBL) in 2022

Understanding how to effectively train for Extravehicular Activities (EVAs) for Artemis missions is critical. Tasked by the new Extravehicular Activity and Human Surface Mobility Program(EHP), a team of stakeholders from engineering and flight operations worked together to test the Exploration Extravehicular Mobility (xEMU) in the Neutral Buoyancy Lab(NBL) simulating the lunar environment. The NBL is a pool in which astronauts are typically trained to complete simulated International Space Station (ISS) EVA tasks in a neutral weigh-out. The overall focus for this test series was evaluating how well the NBL could be used as an effective simulated environment for Artemis lunar EVAs. New NBL support hardware was manufactured to support this test series and update the interfaces to be more representative of xEMU hardware such as a new NBL Portable Life Support System(PLSS)mock-up and umbilical, lights and cameras, and display and control unit (DCU).To simulate the 1/6th-gravity (1/6-g) environment, extra weights were added around the suit to create an accurate center of gravity representation. The Partial Gravity Weigh-out Stand (PGWS) predicted where and how much weight would be required for the 1/6th-G simulation and predicted the center of gravity placement. After the weigh-out attempt was completed, the suited participant would complete a set of directed tasks such as kneeling, object pick-up, and walking to evaluate the weigh-out. To create the lunar environment, sand, boulders, and ramps were added to the pool floor. If time allowed after weigh-out was determined acceptable, the flight operations team would direct the suited participants to complete simulated Artemis EVA tasks using flight-like tools and tool cart. The team also evaluated turning out the overhead lights in the NBL for a portion of some of the test runs and using a solar simulator to create amore realistic lunar south pole lighting environment. The test series completed one unmanned test and nine manned tests. With four of the tests, dual xEMU suited operations were completed with subjects in both the small and large xEMU sizes. Overall, the NBL was able to create an acceptable lunar landscape and ability to have two subjects work side by side in pressurized xEMUs which currently cannot be achieved in other test environments. Achieving a stable 1/6th-G lunar weigh-out and clear, consistent dual suit communications was a challenge for this series. Future work is planned to continue to improve this simulation environment.

spacesuit↗

NASA NTRS1977

Theoretic aspects of the identification of the parameters in the optimal control model

The identification of the parameters of the optimal control model from input-output data of the human operator is considered. Accepting the basic structure of the model as a cascade of a full-order observer and a feedback law, and suppressing the inherent optimality of the human controller, the parameters to be identified are the feedback matrix, the observer gain matrix, and the intensity matrices of the observation noise and the motor noise. The identification of the parameters is a statistical problem, because the system and output are corrupted by noise, and therefore the solution must be based on the statistics (probability density function) of the input and output data of the human operator. However, based on the statistics of the input-output data of the human operator, no distinction can be made between the observation and the motor noise, which shows that the model suffers from overparameterization.

Vanwijk, R. A.↗

NASA NTRS2005

Conflict Resolution Performance in an Experimental Study of En Route Free Maneuvering Operations

NASA has developed a far-term air traffic management concept, termed Distributed Air/Ground Traffic Management (DAG-TM). One component of DAG-TM, En Route Free Maneuvering, allows properly trained flight crews of equipped autonomous aircraft to assume responsibility for separation from other autonomous aircraft and from Instrument Flight Rules (IFR) aircraft. Ground-based air traffic controllers continue to separate IFR traffic and issue flow management constraints to all aircraft. To examine En Route Free Maneuvering operations, a joint human-in-the-loop experiment was conducted in summer 2004 at the NASA Ames and Langley Research Centers. Test subject pilots used desktop flight simulators to resolve traffic conflicts and adhere to air traffic flow constraints issued by subject controllers. The experimental airspace integrated both autonomous and IFR aircraft at varying traffic densities. This paper presents a subset of the En Route Free Maneuvering experimental results, focusing on airborne and ground-based conflict resolution, and the effects of increased traffic levels on the ability of pilots and air traffic controllers to perform this task. The results show that, in general, increases in autonomous traffic do not significantly impact conflict resolution performance. In addition, pilot acceptability of autonomous operations remains high throughout the range of traffic densities studied. Together with previously reported findings, these results continue to support the feasibility of the En Route Free Maneuvering component of DAG-TM.

Doble, Nathan A.↗

NASA NTRS2017

Integration of an Earth-Based Science Team During Human Exploration of Mars

NASA Extreme Environment Mission Operations (NEEMO) is an underwater spaceflight analog that allows a true mission-like operational environment and uses buoyancy effects and added weight to simulate different gravity levels. A mission was undertaken in 2016, NEEMO 21, at the Aquarius undersea research habitat. During the mission, the effects of varied oper-ations concepts with representative communication latencies as-sociated with Mars missions were studied. Six subjects were weighed out to simulate partial gravity and evaluated different operations concepts for integration and management of a simulated Earth-based science team (ST) who provided input and direction during exploration activities. Exploration traverses were planned in advance based on precursor data collected. Subjects completed science-related tasks including presampling surveys and marine-science-based sampling during saturation dives up to 4 hours in duration that simulated extravehicular activity (EVA) on Mars. A communication latency of 15 minutes in each direction between space and ground was simulated throughout the EVAs. Objective data included task completion times, total EVA time, crew idle time, translation time, ST assimilation time (defined as time available for the science team to discuss, to review and act upon data/imagery after they have been collected and transmitted to the ground). Subjective data included acceptability, simulation quality, capability assessment ratings, and comments. In addition, comments from both the crew and the ST were captured during the post-mission debrief. Here, we focus on the acceptability of the operations concepts studied and the capabilities most enhancing or enabling in the operations concept. The importance and challenges of designing EVA time-lines to account for the length of the task, level of interaction with the ground that is required/desired, and communication latency, are discussed.

Chappell, Steven P.↗

NASA NTRSDate not supplied

Upwind Buildings Effects on Test Section Performance of the NFAC 80- by 120-Foot Wind Tunnel

In 2013, a new development began that would put multi-story buildings within the exclusion zone of the 80- by 120- Foot Wind Tunnel (80x120) inlet that exceeded the then existing building height restriction. This raised questions concerning whether the tunnel could operate within the acceptable turbulence limits of ≤ 0.5% in the axial direction over 75% area in the wind tunnel test section. The goal of this testing was to determine the validity of this hypothesis. Testing was performed using the 1/50th-scale model of the 80- by 120-FootWind Tunnel within the full-scale facility test section to characterize the model’s test section turbulence levels as a function of wind direction with the presence of the upwind buildings that are currently being constructed. This paper reports the first testing performed to date on the 80x120 inlet as-built under controlled test conditions for wind magnitude and wind onset direction for a variety of buildings in the inlet external flow field, including no buildings (the control case). This testing determined that, at rated operational conditions the upwind blockages caused no increase in turbulence intensity levels measured in the test section and, in some limited cases, caused the turbulence levels to decrease. Lastly, looking at generic rectangular blockages showed that, to have a discernible effect on test section turbulence levels, scaled 100-ft tall blockages need to be within 600 ft of the existing inlet.

Upwind Buildings Effects↗

NASA NTRSDate not supplied

Helicopter Pilot Evaluations of the Airborne Collision Avoidance System Xr in a High-Fidelity Motion Simulation

New aircraft and aerial Urban Air Mobility operations require updated technologies to maintain vehicle separation during flight. Specifically, higher-density airspace will need more than traditional air traffic control to keep vehicles well clear of each other and avoid Near Midair Collisions. In response, the Federal Aviation Administration is currently developing the Airborne Collision Avoidance System X (ACAS X) for next-generation air traffic deconfliction, which provides caution-level and warning-level alerts in response to multiple aircraft types. This study recruited six helicopter pilots to fly an electric vertical takeoff and landing vehicle model in simulated operations under Visual Flight Rules (VFR). Flights were accomplished using the high-fidelity Vertical Motion Simulator at the NASA Ames Research Center. Participants controlled the vehicle using two side inceptors and foot rudders. The rotorcraft variant of ACAS X (ACAS Xr) was provided for alerting and guidance during traffic conflicts. Pilots used this system while giving feedback to the researchers through questionnaires, debriefs, and other discussions. Variables of interest to the study were phases of flight (i.e., Cruise, Hover, and Approach) and ACAS Xr configurations: The Collision Avoidance System configuration behaves similarly to current commercial traffic systems used for tactical deconfliction in crewed vehicles, and the Detect and Avoid configuration was developed to provide extra, corrective-level guidance for unmanned aircraft systems. Results showed that pilots found the alerting and guidance from ACAS Xr useful, effective, and acceptable for VFR operations. Certain elements, like speed guidance and text banners, were found to be of no use to the pilots. Hover and Approach scenarios were considered the most difficult for ACAS Xr alerting. Reasons for this difficulty were partially due to learning interference (i.e., overcoming previously learned behavior) and partially due to the vehicle model (i.e., NASA’s Lift Plus Cruise design). Still, alerting-based confounds reveal the need for more development for ACAS Xr during these Hover and Approach flight phases. Study caveats and future projects are discussed.

air taxis↗

NASA NTRSDate not supplied

Helicopter Pilot Evaluations of the Airborne Collision Avoidance System Xr in a High-Fidelity Motion Simulation

New aircraft and aerial Urban Air Mobility operations require updated technologies to maintain vehicle separation during flight. Specifically, higher-density airspace will need more than traditional air traffic control to keep vehicles well clear of each other and avoid Near Midair Collisions. In response, the Federal Aviation Administration is currently developing the Airborne Collision Avoidance System X (ACAS X) for next-generation air traffic deconfliction, which provides caution-level and warning-level alerts in response to multiple aircraft types. This study recruited six helicopter pilots to fly an electric vertical takeoff and landing vehicle model in simulated operations under Visual Flight Rules (VFR). Flights were accomplished using the high-fidelity Vertical Motion Simulator at the NASA Ames Research Center. Participants controlled the vehicle using two side inceptors and foot rudders. The rotorcraft variant of ACAS X (ACAS Xr) was provided for alerting and guidance during traffic conflicts. Pilots used this system while giving feedback to the researchers through questionnaires, debriefs, and other discussions. Variables of interest to the study were phases of flight (i.e., Cruise, Hover, and Approach) and ACAS Xr configurations: The Collision Avoidance System configuration behaves similarly to current commercial traffic systems used for tactical deconfliction in crewed vehicles, and the Detect and Avoid configuration was developed to provide extra, corrective-level guidance for unmanned aircraft systems. Results showed that pilots found the alerting and guidance from ACAS Xr useful, effective, and acceptable for VFR operations. Certain elements, like speed guidance and text banners, were found to be of no use to the pilots. Hover and Approach scenarios were considered the most difficult for ACAS Xr alerting. Reasons for this difficulty were partially due to learning interference (i.e., overcoming previously learned behavior) and partially due to the vehicle model (i.e., NASA’s Lift Plus Cruise design). Still, alerting-based confounds reveal the need for more development for ACAS Xr during these Hover and Approach flight phases. Study caveats and future projects are discussed.

air taxis↗

NASA NTRS2012

Characterization of Aerodynamic Performance of Boundary-Layer-Ingesting Inlet Under Crosswind

NASA has been studying future transport concepts, envisioned to be technically realizable in the timeframe of 2020-2030, to meet environmental and performance goals. One concept receiving considerable interest involves a propulsion system embedded into a hybrid wing-body aircraft. While offering significant advantages in fuel savings and noise reduction by this concept, there are several technical challenges that are not encountered in the current fleet and must be overcome so as to deliver target performance and operability. One of these challenges is associated with an inlet system that ingests a significantly thick boundary layer, developing along the wing-body surface, into a serpentine diffuser before the flow meeting fan blades. The flow is subject to considerable total pressure loss and distorted at the fan face, much more significantly than in the inlet system of conventional aircraft. In our previous studies [1, 2], we have shown that through innovative design changes on the airframe surface, it is possible to simultaneously increase total pressure recovery and decrease distortion in the flow, without resorting to conventional penalty-ridden flow control concepts, such as vortex generator or boundary layer bleeding/suction. In the current study, we are interested in understanding the following issues: how the embedded propulsion system performs under a crosswind condition by studying in detail the flow characteristics of two inlets, the baseline and another optimized previously under the cruise condition. With the insight, it is hoped that it can help in the follow-on study by devising effective strategies to minimize flow distortion arising from the integration of an embedded-engine system into an airframe to the level acceptable to the operation and fuel consumption before 2030. To achieve these demanding goals, non-conventional concepts are called for; but technology gap is too big that it requires evolutionary approach by focusing various concepts and technologies needed in the next three generations of aircraft, respectively named as N+1, N+2, and N+3. Noticeably, considerable reduction in each category of 1 is required in N+2 (relative to Boeing 777-200 and GE90 engines) and N+3 (relative to Boeing 737-800 and CFM56-7B engines). In this study, concepts for N+2 is our interest. A concept that has potential to achieve these metrics and has been under intensive study is the hybrid wing body (HWB) airframe with a tightly integrated propulsion system, see Fig. 1. The inlet is non-circular at the entrance and the entering flow, no longer uniform or free of disturbances, and is now carrying with it a boundary layer developing along the fuselage; the inlet is thus known as boundary-layer-ingesting (BLI) inlet.

Liou, Meng-Sing↗

NASA NTRS2004

Unique Systems Analysis Task 7, Advanced Subsonic Technologies Evaluation Analysis

To retain a preeminent U.S. position in the aircraft industry, aircraft passenger mile costs must be reduced while at the same time, meeting anticipated more stringent environmental regulations. A significant portion of these improvements will come from the propulsion system. A technology evaluation and system analysis was accomplished under this task, including areas such as aerodynamics and materials and improved methods for obtaining low noise and emissions. Previous subsonic evaluation analyses have identified key technologies in selected components for propulsion systems for year 2015 and beyond. Based on the current economic and competitive environment, it is clear that studies with nearer turn focus that have a direct impact on the propulsion industry s next generation product are required. This study will emphasize the year 2005 entry into service time period. The objective of this study was to determine which technologies and materials offer the greatest opportunities for improving propulsion systems. The goals are twofold. The first goal is to determine an acceptable compromise between the thermodynamic operating conditions for A) best performance, and B) acceptable noise and chemical emissions. The second goal is the evaluation of performance, weight and cost of advanced materials and concepts on the direct operating cost of an advanced regional transport of comparable technology level.

Eisenberg, Joseph D.↗

NASA NTRS2010

Use of Data Comm by Flight Crew in High-Density Terminal Areas

This paper describes a collaborative FAA and NASA experiment using 22 commercial airline pilots to determine the effect of using Datalink Communication (Data Comm) to issue messages in busy, terminal area operations. Four conditions were defined that span current day to future flight deck equipage levels (voice communication only, Data Comm only, Data Comm with Moving Map Display, Data Comm with Moving Map displaying taxi route), and each condition was used to create an arrival and a departure scenario at the Boston Logan Airport. These eight scenarios were repeated twice for a total of 16 scenarios for each of the eleven crews. Quantitative data was collected on subject reaction time and eye tracking information. Questionnaires collected subjective feedback on workload and acceptability to the flight crew for using Data Comm in a busy terminal area. 95% of the Data Comm messages were responded to by the flight crew within one minute; however, post experiment debrief comments revealed almost unanimous consensus that two minutes was a reasonable expectation for crew response. Eye tracking data indicated an insignificant decrease in head-up time for the Pilot Flying when Data Comm was introduced; however, the Pilot Monitoring had significantly less head-up time. Data Comm workload was rated as operationally acceptable by both crew members in all conditions in flight at any altitude above the Final Approach Fix in terms of response time and workload. Results also indicate the use of Data Comm during surface operations was acceptable, the exception being the simultaneous use of voice, Data Comm, and audio chime required for an aircraft to cross an active runway. Many crews reported they believed Data Comm messages would be acceptable after the Final Approach Fix or to cross a runway if the message was not accompanied by a chime and there was not a requirement to immediately respond to the uplink message.

Baxley, Brian T.↗

NASA NTRS1973

Extravehicular mobility unit thermal simulator

The analytical methods, thermal model, and user's instructions for the SIM bay extravehicular mobility unit (EMU) routine are presented. This digital computer program was developed for detailed thermal performance predictions of the crewman performing a command module extravehicular activity during transearth coast. It accounts for conductive, convective, and radiative heat transfer as well as fluid flow and associated flow control components. The program is a derivative of the Apollo lunar surface EMU digital simulator. It has the operational flexibility to accept card or magnetic tape for both the input data and program logic. Output can be tabular and/or plotted and the mission simulation can be stopped and restarted at the discretion of the user. The program was developed for the NASA-JSC Univac 1108 computer system and several of the capabilities represent utilization of unique features of that system. Analytical methods used in the computer routine are based on finite difference approximations to differential heat and mass balance equations which account for temperature or time dependent thermo-physical properties.

Hixon, C. W.↗

NASA NTRS1974

The cryogenic wind tunnel for high Reynolds number testing

Experiments performed at the NASA Langley Research Center in a cryogenic low-speed continuous-flow tunnel and in a cryogenic transonic continuous-flow pressure tunnel have demonstrated the predicted changes in Reynolds number, drive power, and fan speed with temperature, while operating with nitrogen as the test gas. The experiments have also demonstrated that cooling to cryogenic temperatures by spraying liquid nitrogen directly into the tunnel circuit is practical and that tunnel temperature can be controlled within very close limits. Whereas most types of wind tunnel could operate with advantage at cryogenic temperatures, the continuous-flow fan-driven tunnel is particularly well suited to take full advantage of operating at these temperatures. A continuous-flow fan-driven cryogenic tunnel to satisfy current requirements for test Reynolds number can be constructed and operated using existing techniques. Both capital and operating costs appear acceptable.

Kilgore, R. A.↗

NASA NTRS1976

Delayed flap approach procedures for noise abatement and fuel conservation

The NASA/Ames Research Center is currently investigating the delayed flap approach during which pilot actions are determined and prescribed by an onboard digital computer. The onboard digital computer determines the proper timing for the deployment of the landing gear and flaps based on the existing winds and airplane gross weight. Advisory commands are displayed to the pilot. The approach is flown along the conventional ILS glide slope but is initiated at a higher airspeed and in a clean aircraft configuration that allows for low thrust and results in reduced noise and fuel consumption. Topics discussed include operational procedures, pilot acceptability of these procedures, and fuel/noise benefits resulting from flight tests and simulation.

Edwards, F. G.↗

NASA NTRS1979

Experimental Evaluation of a Low Emissions High Performance Duct Burner for Variable Cycle Engines (VCE)

An evaluation was conducted with a three stage Vorbix duct burner to determine the performance and emissions characteristics of the concept and to refine the configuration to provide acceptable durability and operational characteristics for its use in the variable cycle engine (VCE) testbed program. The tests were conducted at representative takeoff, transonic climb, and supersonic cruise inlet conditions for the VSCE-502B study engine. The test stand, the emissions sampling and analysis equipment, and the supporting flow visualization rigs are described. The performance parameters including the fuel-air ratio, the combustion efficiency/exit temperature, thrust efficiency, and gaseous emissions calculations are defined. The test procedures are reviewed and the results are discussed.

Lohmann, R. P.↗

NASA NTRS1980

Solar heating and cooling demonstration project at the Florida solar energy center

The retrofitted solar heating and cooling system installed at the Florida Solar Energy Center is described. The system was designed to supply approximately 70 percent of the annual cooling and 100 percent of the heating load. The project provides unique high temperature, nonimaging, nontracking, evacuated tube collectors. The design of the system was kept simple and employs five hydronic loops. They are energy collection, chilled water production, space cooling, space heating and energy rejection. Information is provided on the system's acceptance test results operation, controls, hardware and installation, including detailed drawings.

Source record↗