SEARCH · Search NASA

Results for “PITCHING MOMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS2005

Parachute Aerodynamics From Video Data

A new data analysis technique for the identification of static and dynamic aerodynamic stability coefficients from wind tunnel test video data is presented. This new technique was applied to video data obtained during a parachute wind tunnel test program conducted in support of the Mars Exploration Rover Mission. Total angle-of-attack data obtained from video images were used to determine the static pitching moment curve of the parachute. During the original wind tunnel test program the static pitching moment curve had been determined by forcing the parachute to a specific total angle-of -attack and measuring the forces generated. It is shown with the new technique that this parachute, when free to rotate, trims at an angle-of-attack two degrees lower than was measured during the forced-angle tests. An attempt was also made to extract pitch damping information from the video data. Results suggest that the parachute is dynamically unstable at the static trim point and tends to become dynamically stable away from the trim point. These trends are in agreement with limit-cycle-like behavior observed in the video. However, the chaotic motion of the parachute produced results with large uncertainty bands.

Schoenenberger, Mark↗

NASA NTRS1994

Wind Tunnel Results of Pneumatic Forebody Vortex Control Using Rectangular Slots a Chined Forebody

A subsonic wind tunnel investigation of pneumatic vortex flow control on a chined forebody using slots was accomplished at a dynamic pressure of 50 psf resulting in a R(n)/ft of 1.3 x 10(exp 6). Data were acquired from angles of attack ranging from -4deg to +34deg at side slips of +0.4deg and +10.4deg. The test article used in this study was the 10% scale Fighter Lift and Control (FLAC) advanced diamond winged, vee-tailed fighter configuration. Three different slot blowing concepts were evaluated; outward, downward, and tangential with ail blowing accomplished asymmetrically. The results of three different mass flows (0.067, 0.13, and 0.26 lbm/s; C(sub mu)'s of less than or equal to 0.006, 0.011. and 0.022 respectively) were analyzed and reported. Test data are presented on the effects of mass flows, slot lengths and positions and blowing concepts on yawing moment and side force generation. Results from this study indicate that the outward and downward blowing slots developed yawing moment and side force increments in the direction opposite of the blowing side while the tangential blowing slots generated yawing moment and side force increments in the direction towards the blowing side. The outward and downward blowing slots typically produced positive pitching moment increments while the tangential blowing slots typically generated negative pitching moment increments. The slot blowing nearest the forebody apex was most effective at generating the largest increments and as the slot was moved aft or increased in length, its effectiveness at generating forces and moments diminished.

Alexander, Michael↗

NASA NTRS1973

The results of a low speed wind tunnel test to investigate the effects of installing refan JT8D engines on the McDonnell Douglas DC-9-30

A low speed wind tunnel test was conducted to assess the effects of the larger JT8D refan nacelles on the stability and control characteristics of the DC-9-30, with emphasis on the deep stall regime. Deep stall pitching moment and elevator hinge moment data, and low angle of attack tail-on and tail-off pitching moment data are presented. The refan nacelle was tested in conjunction with various pylons of reduced span relative to the production DC-9-30 pylon. Also, a horizontal tail that was larger than the production tail was tested. The data show that the refan installation has a small detrimental effect on the DC-9-30 deep stall recovery capability, that recovery characteristics are essentially independent of pylon span, and that the larger horizontal tail significantly increases recovery margins. The deep stall characteristics with the refan installation, within the range of pylon spans tested, are acceptable with no additional design changes anticipated.

Chrisenberry, H. E.↗

NASA NTRS1983

A review of preflight estimates of real-gas effects on space shuttle aerodynamic characteristics

Preflight estimates of the hypersonic aerodynamic characteristics of the Shuttle orbiter were based on a diverse series of research studies using state of the art techniques developed by basic research in the 60's and 70's. Real-gas viscous calculations on simple shapes that were used to evaluate correlation parameters indicated that real-gas effects reduce aerodynamic forces and moments. Inviscid calculations on winged lifting shapes indicated reduced forces and a slight nose-up pitch resulted because of real-gas effects. Analysis of the extensive wind tunnel data base indicated viscous correlation parameters provided the most appropriate extrapolation technique for estimating flight aerodynamics. Variations because of changes in the ratio of specific heats, which was the only available experimental tool for evaluating real-gas effects, indicated that reduced loads and nose-up pitching moments would occur at high altitudes and Mach numbers but that the values would not exceed the tolerances and variations established about the aerodynamic design data book values derived from viscous correlations. During STS-1, nose-up pitching moments exceeded the established variations.

Woods, W. C.↗

NASA NTRS1950

Free-Flight Investigation of the Static and Dynamic Longitudinal Stability Characteristics of 1/3.7-Scale Rocket-Powered Models of the Bell MX-776A

An investigation of the static and dynamic longitudinal stability characteristics of 1/3.7 scale rocket-powered model of the Bell MX-776A has been made for a Mach number range from 0.8 to 1.6. Two models were tested with all control surfaces at 0 degree deflection and centers of gravity located 1/4 and 1/2 body diameters, respectively, ahead of the equivalent design location. Both models were stable about the trim conditions but did not trim at 0 degree angle of attack because of slight constructional asymmetries. The results indicated that the variation of lift and pitching moment was not linear with angle of attack. Both lift-curve slope and pitching-moment-curve slope were of the smallest magnitude near 0 degree angle of attack. In general, an increase in angle of attack was accompanied by a rearward movement of the aerodynamic center as the rear wing moved out of the downwash from the forward surfaces. This characteristic was more pronounced in the transonic region. The dynamic stability in the form of total damping factor varied with normal-force coefficient but was greatest for both models at a Mach number of approximately 1.25. The damping factor was greater at the lower trim normal-force coefficients except at a Mach number of 1.0. At that speed the damping factor was of about the same magnitude for both models. The drag coefficient increased with trim normal-force coefficient and was largest in the transonic region.

Michal, David H.↗

NASA NTRS1974

Engineering simulation evaluation of the two-segment noise abatement approach in the Douglas DC-8-61

The development and operational evaluation are discussed of a noise abatement two-segment approach which is safe and operationally acceptable for routine use in air carrier service. An engineering simulation evaluation was conducted; it was found that the entry speed and initial configuration are more important in the DC-8-61 than in the 727 because of the DC-8's aerodynamic cleanliness and drag programming constraints. It was also found that the altitude required for the DC-8 upper and lower transitions is less than the 727 transitions principally due to the pitching moment from the underslung DC-8 engines as compared to the 727 engines which produce no pitching moment with a change in thrust. The 727 approach was a reduced flaps (30 degrees) procedure with a 10-knot airspeed bleed in the lower transition; the DC-8 approach is a full flaps (50 degrees) procedure with constant airspeed established as soon as possible after upper segment transition.

Nylen, W. E.↗

NASA NTRS2011

Icing Encounter Duration Sensitivity Study

This paper describes a study performed to investigate how aerodynamic performance degradation progresses with time throughout an exposure to icing conditions. It is one of the first documented studies of the effects of ice contamination on aerodynamic performance at various points in time throughout an icing encounter. Both a 1.5 and 6 ft chord, two-dimensional, NACA-23012 airfoils were subjected to icing conditions in the NASA Icing Research Tunnel for varying lengths of time. At the end of each run, lift, drag, and pitching moment measurements were made. Measurements with the 1.5 ft chord model showed that maximum lift and pitching moment degraded more rapidly early in the exposure and degraded more slowly as time progressed. Drag for the 1.5 ft chord model degraded more linearly with time, although drag for very short exposure durations was slightly higher than expected. Only drag measurements were made with the 6 ft chord airfoil. Here, drag for the long exposures was higher than expected. Novel comparison of drag measurements versus an icing scaling parameter, accumulation parameter times collection efficiency was used to compare the data from the two different size model. The comparisons provided a means of assessing the level of fidelity needed for accurate icing simulation.

Addy, Harold E., Jr.↗

NASA NTRS1972

Nacelle-airframe interference at low supersonic Mach numbers.

The aerodynamic interference between the propulsion system and airframe for a low supersonic transport with wing-mounted nacelles is examined. Both a flowfield analysis and the equivalent body approach were used to predict the interference lift, drag, and pitching moment as functions of nacelle size, shape, and position. The results indicate that the interference lift and pitching moment, as well as drag, must be included in the analysis to properly assess the interference effects. In addition, the performance of the basic wing was found to play an important role in determining the effectiveness of the interference lift in reducing the net installation drag. Based on a conservative prediction, the interference effects can reduce the installed propulsion system drag to 40% of the isolated drag of the nacelles. Furthermore, including the interference effects in the optimization of the engine cycle from a thermodynamic and weight standpoint can result in a considerable reduction in the net propulsion system weight fraction (fuel plus engines) while increasing the optimum engine bypass ratio of a typical transport vehicle.

Bencze, D. P.↗

NASA NTRS1955

Note on Hovering Turns with Tandem Helicopters

The source of an appreciable pitching-moment difference between left and right hovering turns for a tandem helicopter is described. The difference in pitching moment results from the difference in rotational speed of the counter rotating rotors with respect to the air while the helicopter is turning.

HELICOPTERS↗

NASA NTRS2010

Computational Aeroelastic Analysis of Ares Crew Launch Vehicle Bi-Modal Loading

A Reynolds averaged Navier-Stokes analysis, with and without dynamic aeroelastic effects, is presented for the Ares I-X launch vehicle at transonic Mach numbers and flight Reynolds numbers for two grid resolutions and two angles of attack. The purpose of the study is to quantify the force and moment increment imparted by the sudden transition from fully separated flow around the crew module - service module junction to that of the bi-modal flow state in which only part of the flow reattaches. The bi-modal flow phenomenon is of interest to the guidance, navigation and control community because it causes a discontinuous jump in forces and moments. Computations with a rigid structure at zero zero angle of attack indicate significant increases in normal force and pitching moment. Dynamic aeroelastic computations indicate the bi-modal flow state is insensitive to vehicle flexibility due to the resulting deflections imparting only very small changes in local angle of attack. At an angle of attack of 2.5deg, the magnitude of the pitching moment increment resulting from the bi-modal state nearly triples, while occurring at a slightly lower Mach number. Significant grid induced variations between the solutions indicate that further grid refinement is warranted.

Massey, Steven J.↗

NASA NTRS1995

Measurements of store forces and moments and cavity pressures for a generic store in and near a box cavity at subsonic and transonic speeds

An experimental force and moment study was conducted in the Langley 8-Foot Transonic Pressure Tunnel for a generic store in and near rectangular box cavities contained in a flat-plate configuration at subsonic and transonic speeds. Surface pressures were measured inside the cavities and on the flat plate. The length-to-height ratios were 5.42, 6.25, 10.83, and 12.50. The corresponding width-to-height ratios were 2.00, 2.00, 4.00, and 4.00. The free-stream Mach number range was from 0.20 to 0.95. Surface pressure measurements inside the cavities indicated that the flow fields for the shallow cavities were either closed or transitional near the transitional/closed boundary. For the deep cavities, the flow fields were either open or near the open/transitional boundary. The presence of the store did not change the type of flow field and had only small effects on the pressure distributions. For transitional or open transitional flow fields, increasing the free-stream Mach number resulted in large reductions in pitching-moment coefficient. Values of pitching-moment coefficient were always much greater for closed flow fields than for open flow fields.

Stallings, Robert L., Jr.↗

NASA NTRS1978

Theoretical evaluation of high speed aerodynamics for arrow wing configurations

A limited study in the use of theoretical methods to calculate the high speed aerodynamics of arrow wing supersonic cruise configurations was conducted. The study consisted of correlations with existing wind tunnel data at Mach numbers from 0.8 to 2.7, using theoretical methods to extrapolate the wind tunnel data to full scale flight conditions, and presentation of a typical supersonic data package for an advanced supersonic transport application prepared using the theoretical methods. A brief description of the methods and their application was given. In general, all three methods had excellent correlation with wind tunnel data at supersonic speeds for drag and lift characteristics and fair to poor agreement with pitching moment characteristics. The VORLAX program had excellent correlation with wind tunnel data at subsonic speeds for lift and pitching moment characteristics and fair agreement in drag characteristics.

Dollyhigh, S. M.↗

NASA NTRS1952

Wind-Tunnel Investigation of the Static Longitudinal Stability Characteristics of a 0.15-Scale Model of the Hermes A-1E2 Missile at High Subsonic Mach Numbers

The static longitudinal stability characteristics of a 0.15-scale model of the Hermes A-lE2 missile have been determined in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.50 to 0.98, corresponding to Reynolds numbers, based on body length, of 12.3 x 10(exp 6) to 17.1 x 10(exp 6). This paper presents results obtained with body alone and body-fins combinations at 0 degrees (one set of fins vertical and the other set horizontal) and 45 degree angle of roll. The results indicate that the addition of the fins to the body insures static longitudinal stability and provides essentially linear variations of the lift and pitching moment at small angles of attack throughout the Mach number range. The slopes of the lift and pitching-moment curves vary slightly with Mach number and show only small effects due to the angle of roll.

Alford, William J., Jr.↗

NASA NTRS1994

An experimental and theoretical study of the aerodynamic characteristics of some generic missile concepts at Mach numbers from 2 to 6.8

A study has been made of the experimental and theoretical aerodynamic characteristics for some generic high-speed missile concepts at Mach numbers from 2 to 6.8. The basic body for this study had a length-to-diameter ratio of 10 with the forward half being a modified blunted ogive and the rear half being a cylinder. Modifications made to the basic body included the addition of an after body flare, the addition of highly swept cruciform wings and the addition of highly swept aft tails. The effects of some controls were also investigated with all-moving wing controls on the flared body and trailing-edge flap controls on the winged body. The results indicated that the addition of a flare, wings, or tails to the basic body all provided static longitudinal stability with varying amounts of increased axial force. The control arrangements were effective in producing increments of normal-force and pitching-moment at the lower Mach numbers. At the highest Mach number, the flap control on the winged body was ineffective in producing normal-force or pitching-moment but the all-moving wing control on the flared body, while losing pitch effectiveness, still provided normal-force increments. Calculated results obtained through the use of hypersonic impact theory were in generally good agreement with experiment at the higher Mach numbers but were not accurate at the lower Mach numbers.

Spearman, M. Leroy↗

NASA NTRSDate not supplied

Improvements in Simulating a Mach 0.80 Transonic Truss-Braced Wing Configuration using the Spalart-Allmaras and k-ω SST Turbulence

Teams from the NASA Ames Research Centers (ARC) and Langley Research Center (LaRC) have been working on validating their computational fluid dynamics (CFD) results for the Boeing Mach 0.80 Transonic Truss-Braced Wing (TTBW) configuration. Experimental data used for the validation were gathered from a test conducted of a 4.5% scale Mach 0.80 TTBW model in the NASA Ames Research Center 11-by 11-Foot Transonic Wind Tunnel. The CFD simulations were initially run with both LAVA and USM3D Mixed Element solvers utilizing the Spalart-Allmaras (SA) turbulence model. A discrepancy was observed between CFD and experimental loads and moments ranging on average from 0.047 to 0.063 for lift coefficient, 16.5 to 27 in drag counts, and -0.02 to -0.032 for pitching moment, varying with the solver used. With introducing the refactored version of LAVA these values dropped to 0.034 to 0.047 for lift coefficient, 7.74 to 16.5 in drag counts, and lastly -0.012 to -0.02 for pitching moment. Based on findings from Boeing, who observed an improved comparison to experimental data when using the k-ω Shear Stress Transport (SST) turbulence model, the NASA teams conducted simulations with SST to investigate turbulence modeling sensitivities. OVERFLOW and USM3D V6 solvers were used for the comparison of SST and SA simulations. CFD results using the SST turbulence model demonstrate an improvement in matching with experimental CL values, reducing the discrepancies seen by 0.021-0.055 (62-93% reduction in discrepancy respective to the OVERFLOW and USM3D V6). The SST model has varying effects on CD, based on the solver / grid paradigm; for USM3D this prediction is only improved at higher angles of attack (above the cruise design point) resulting in a reduced discrepancy of 8.8–25 drag counts However, at the mid-to-low angles of attack, SST increases the CD discrepancy by 4-55 counts, increasing at lower angles of attack. For OVERFLOW this discrepancy only exists at the low angles of attack and maxes out at 10 counts of drag. Above α = 1.5° OVERFLOW SST reduces discrepancy by 9.3 drag counts on average.

AATT↗

NASA NTRS1959

Investigation of the Stability of Very Flat Spins and Analysis of Effects of Applying various Moments Utilizing the Three Moment Equations of Motion

Based on linearized equations of motion utilizing only the three moment equations and assuming only flat-spin conditions, it appears that contemporary designs (with the moment of inertia about the wing axis I(sub Y) considerably greater than the moment of inertia about the fuselage axis I(sub X) having positive values of C(sub l, sub p) (rolling-moment coefficient due to rolling) or positive values of C(sub l, sub beta) (rolling-moment coefficient due to sideslip) will probably not have a stable spin in the flat-spin region near an angle of attack of 90 deg. If the damping in pitch in flat-spin attitudes is zero, stable flat-spin conditions may not be possible on an airplane having the mass primarily distributed along the wings. The effect of moving ailerons with the spin or the effect of applying a positive pitching moment producing recovery for contemporary fighter designs will be greatest for large negative values of C(sub n, sub beta) (yawing-moment coefficient due to sideslip). In addition, for a certain critical value of positive C(sub n, sub beta), the rolling moment applied by moving ailerons with the spin or the application of a positive pitching moment will have no effect on reducing the spin rate.

Klinar, Walter J.↗

NASA NTRS1961

Static Lateral Characteristics at High Subsonic Speeds of a Complete Airplane Model with a Highly Tapered Wing having the 0.80 Chord Line Unswept and with Several Tail Configurations

An investigation was made at high subsonic speeds of a complete model having a highly tapered wing and several tail configurations. The aspect-ratio-3.50 wing had a taper ratio of 0.067 and an unswept 0.80 chord line. The complete model was tested with a wing-chord-plane tail, a T-tail, and a biplane tail (combined T-tail and wing-chord-plane tail). The model was tested in the Langley high-speed 7- by 10-foot tunnel at Mach numbers from 0.60 to 0.92 over a range of angle of attack of about +/- 20 deg. and a range of sideslip of -15 deg. to 13 deg. Some data were obtained with the horizontal stabilizer deflected. A few tests were also made with the wing tips clipped to an aspect ratio of 3.00. The data show that shock-interference effects between the tail surfaces (T-tail) can have considerable influence on the directional stability and effective dihedral. For example, the T-tail configuration with horizontal-tail leading-edge overhang showed a considerable loss in directional stability as the angle of attack was reduced to zero or negative values; whereas, the T-tail with zero leading-edge overhang showed the loss to be considerably less. The directional stability of the model with the low tail was essentially constant over a range of angle of attack of +/- 50 deg. All configurations tested showed a large reduction in stability at positive and negative angles of attack larger than about 15 deg., probably because of adverse sidewash associated with wing stall. The data show that a wing-chord-plane horizontal tail (low tail) tends to give a positive pitching-moment increment with increase in sideslip angle; whereas, a high tail (T-tail) tends to give negative increments in pitching moment.

Goodson, Kenneth W.↗

NASA NTRS1986

An experimental study of a three lifting surface configuration

The aerodynamic ramifications of utilizing three lifting surfaces as opposed to the conventional or canard lifting configurations have been studied on a theoretical basis by previous researchers. This paper presents an experimental investigation of various configuration modifications for an unyawed typical business jet at a Reynolds number of 1.3 million. The three surface has better lift and high-lift drag characteristics than either the canard or tail-aft configurations, but the cruise drag is more. The induced drag at cruise is highest for the canard and lowest for the tail-aft configuration. The pitching moment characteristics are somewhat between those of the canard and tail-aft configurations. A decrease in gap adversely affects the pitching moment characteristics. A smaller stagger leads to better aerodynamic and stability characteristics. A decrease in span of the forward wing gives better cruise drag and longitudinal stability characteristics, but has adverse effects on high-lift drag. A variation in the incidence angles of either or both the forward and aft wings changes the zero-lift moments of the configuration, while marginally affecting overall lift and drag. At cruise, the lift to drag ratio is highest for the conventional and lowest for the three surface. For high lift conditions, the order is reversed.

Ostowari, C.↗