Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASTICS INDUSTRY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Super Clean, Super Safe

The Supersonic Gas/Liquid Cleaning System (SS-GLCS) has applications ranging from cleaning circuit boards to scouring building exteriors. The system does not abrade the surface of the hardware being cleaned, and it requires much lower levels of pressure while using very little water. An alternative to CFC-based solvents, the system mixes air and water from separate pressurized tanks, ejecting the gas- liquid mixture at supersonic speeds from a series of nozzles at the end of a hand-held wand. The water droplets have the kinetic energy to forcibly remove the contaminant material. The system leaves very little fluid that must be handled as contaminated waste. It can be applied in the aerospace, automotive, and medical industries, as well as to circuit boards, electronics, machinery, metals, plastics, and optics. With a nozzle that can be oriented in any direction, the system is adjustable to allow all sides of a part to be cleaned without reorientation. It requires minimal training and is easily moved on built-in casters

Source record↗

Low-Velocity Impact Performances of Healed Polymer Fiber Reinforced Plastics

Extending the lifecycle of traditional carbon or glass fiber-reinforced plastics is a complicated problem. The lack of sustainability limits the applications of the traditional composite materials in the vehicle industries where recycling and repurposing are critical issues. Alternatives for the low-stressed structural components are polymer fiber-reinforced plastics (PFRPs). In PFRPs, both the fibers and matrix are composed of thermoplastic polymers (e.g. polypropylene or polyethylene). They are lightweight, easy to manufacture, and cost-effective. Additionally, recycling and repurposing thermoplastic polymers are well understood. Therefore, the PFRPs have strong advantages compared to the traditional fiber-reinforced composites in low-stressed structural applications. In this study, we investigated the low-velocity impact (LVI) performances of the PFRPs and compared them with carbon fiber-reinforced plastics (CFRPs). A semi-spherical impactor was dropped to flat, square panels, and the absorbed impact energy was measured. The damage mechanisms were examined using a Xray µCT scan. The PFRPs outperformed the CFRPs in terms of perforation energy normalized by plate thickness and density. After the perforation, we healed the fractured plates by leveraging the recyclability of the thermoplastic polymers. The healing process of the panels was identical to the initial panel manufacturing process. No additional materials were added during the healing process. The healed PFRP panels were impacted again and substantially recovered energy absorption capability. We also conducted the repeated-impact test with several different impact energies. Unlike the CFRPs where the impact peak load decreased as the impacts repeated, the PFRPs showed an increasing trend. Such a unique mechanism was due to the strain-hardening behavior of the polymer fibers and matrix. As a result, the repeated-impact life of the PFRPs was significantly enhanced. These results are particularly interesting in the automotive or aerospace industries where repeated LVI is frequently observed.

Ko, Seunghyun↗

Controlling the Plastic Anisotropy of Magnesium Alloy by Tailoring the Grain Size and Yttrium Content

Hexagonal close-packed (HCP) magnesium alloys are widely used in automotive and aerospace industries due to their low density and high specific-strength. Their applicability is mainly restricted due to poor formability and pronounced plastic anisotropy. The formability is usually improved by altering the chemistry (adding rare-earth elements like Y) or modulating the microstructure (e.g., grain refinement). However, grain refinement alone cannot yield the desired ductility, and the scarcity of rare-earth elements also limits the extent to which the alloying strategy can be used. To overcome these issues, in this work, it is proposed that the formability of Mg alloys can be improved by combining the grain refinement and alloying approaches. To quantitively explore this possibility, a crystal-plasticity-based constitutive model, which is sensitive to both alloying concentration and grain sizes, is developed. To demonstrate, the model is applied to study the combined effect of Y content and grain size on the mechanical responses of Mg alloy. The calculations are used to build maps of plastic anisotropy measures, such as tension–compression asymmetry ratio and Lankford coefficients, for a wide range of Y content and grain sizes. From these maps, the grain size that would yield the desired performance of Mg alloy for a fixed Y content can be identified. This work provides an accelerated pathway to optimize both the microstructure and chemistry simultaneously to achieve formability and to reduce the dependence on alloying.

36 MATERIALS SCIENCE↗

Assembly and comparative genome analysis of a Patagonian Aureobasidium pullulans isolate reveals unexpected intraspecific variation

Aureobasidium pullulans is a yeast-like fungus with remarkable phenotypic plasticity widely studied for its importance for the pharmaceutical and food industries. So far, genomic studies with strains from all over the world suggest they constitute a genetically unstructured population, with no association by habitat. However, the mechanisms by which this genome supports so many phenotypic permutations are still poorly understood. Recent works have shown the importance of sequencing yeast genomes from extreme environments to increase the repertoire of phenotypic diversity of unconventional yeasts. In this study, we present the genomic draft of A. pullulans strain from a Patagonian yeast diversity hotspot, re-evaluate its taxonomic classification based on taxogenomic approaches, and annotate its genome with high-depth transcriptomic data. Here, our analysis suggests this isolate could be considered a novel variant at an early stage of the speciation process. The discovery of divergent strains in a genomically homogeneous group, such as A. pullulans, can be valuable in understanding the evolution of the species. The identification and characterization of new variants will not only allow finding unique traits of biotechnological importance, but also optimize the choice of strains whose phenotypes will be characterized, providing new elements to explore questions about plasticity and adaptation.

59 BASIC BIOLOGICAL SCIENCES↗

Not Cutting Corners: Bioderived Triggers Driving Oxidative Main Chain Scission of Poly(ethylene terephthalate)

About 20–34 billion poly(ethylene terephthalate) (PET) bottles from the beverage industry leak into aquatic ecosystems annually, necessitating the development of urgent strategies to treat waterborne plastic pollution. Inspired by the scalability of water disinfection infrastructure and protocols, we present a dual depolymerization approach relying on oxidation, followed by hydrolysis. Incorporating bioderived monounsaturated C18 diacid (C18:1-DA) counits at low dosages (2–5%) in the PET backbone overcomes the diffusional limitations of depolymerizing PET in the solid state by suppressing the glass transition temperature of the copolymer by 20 °C. Cryomilled C18:1-PET powder suspended in an oxidant-loaded alkaline slurry underwent bulk depolymerization to oligomers at 80–100 °C via oxidative scissions at the internally located unsaturations. In contrast, conventional PET undergoes only minor end-chain scission under mild alkaline conditions. These oligomers are suitable for low-energy repolymerization or facile solvolysis to monomers. A permanganate-periodate oxidant couple demonstrated successful oxidation through the bulk of the polymer, which subsequently was hydrolyzed to monomers. Furthermore, this model system serves as a proxy for ozonolysis, followed by mild hydrolysis to reduce the energetics of alkaline hydrolysis. This integrated oxidation–hydrolysis strategy paves the way for the industrial adoption of cleaner, advanced oxidation processes, such as ozonolysis for plastic pretreatment, further enabling commercialized chemical recycling of unsaturation-containing polyesters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Embedded Heaters for Joining or Separating Plastic Parts

A proposed thermal-bonding technique would make it possible to join or separate thermoplastic parts quickly and efficiently. The technique would eliminate the need for conventional welding or for such conventional fastening components as bolted flanges or interlocking hooks. The technique could be particularly useful in the sign industry (in which large quantities of thermoplastics are used) or could be used to join plastic pipes. A thin sheet of a suitable electrically conductive material would be formed to fit between two thermoplastic parts to be joined (see figure). The electrically conductive sheet and the two parts would be put together tightly, then an electrical current would be sent through the conductor to heat the thermoplastic locally. The magnitude of the current and the heating time would be chosen to generate just enough heat to cause the thermoplastic to adhere to both sides of the electrically conductive sheet. Optionally, the electrically conductive sheet could contain many small holes to provide purchase or to increase electrical resistance to facilitate the generation of heat. After thermal bonding, the electrically conductive sheet remains as an integral part of the structure. If necessary, the electrically conductive sheet can be reheated later to separate the joined thermoplastic parts.

Bryant, Melvin A., III↗

New characterisation method of electrical and electronic equipment wastes (WEEE)

Highlights: ► A novel method of characterisation of components contained in WEEE has been developed. ► This technique was applied on several samples generated from different recycling plants. ► Handheld NIR and XRF were used to determine types of plastics and flame retardants. ► WEEE processing flow-sheet was suggested. - Abstract: Innovative separation and beneficiation techniques of various materials encountered in electrical and electronic equipment wastes (WEEE) is a major improvement for its recycling. Mechanical separation-oriented characterisation of WEEE was conducted in an attempt to evaluate the amenability of mechanical separation processes. Properties such as liberation degree of fractions (plastics, metals ferrous and non-ferrous), which are essential for mechanical separation, are analysed by means of a grain counting approach. Two different samples from different recycling industries were characterised in this work. The first sample is a heterogeneous material containing different types of plastics, metals (ferrous and non-ferrous), printed circuit board (PCB), rubber and wood. The second sample contains a mixture of mainly plastics. It is found for the first sample that all aluminium particles are free (100%) in all investigated size fractions. Between 92% and 95% of plastics are present as free particles; however, 67% in average of ferromagnetic particles are liberated. It can be observed that only 42% of ferromagnetic particles are free in the size fraction larger than 20 mm. Particle shapes were also quantified manually particle by particle. The results show that the particle shapes as a result of shredding, turn out to be heterogeneous, thereby complicating mechanical separation processes. In addition, the separability of various materials was ascertained by a sink–float analysis and eddy current separation. The second sample was separated by automatic sensor sorting in four different products: ABS, PC–ABS, PS and rest product. The fractions were characterised by using the methodology described in this paper. The results show that the grade and liberation degree of the plastic products ABS, PC–ABS and PS are close to 100%. Sink–float separation and infrared plastic identification equipment confirms the high plastic quality. On the basis of these findings, a global separation flow sheet is proposed to improve the plastic separation of WEEE.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Uncertainty Quantification of Fatigue Behavior of Rough AM Surfaces and Microstructures to Enable Hydrogen Gas Turbine

Modifying fossil-fueled industrial gas turbines to utilize low or zero-carbon fuels, such as hydrogen or hydrogen-natural gas blends, is a complex endeavor. The successful implementation of this technology hinges on three key design criteria: (1) developing new fuel injectors capable of efficiently burning alternative fuels, (2) ensuring manufacturability to meet cost and time-to-market goals, and (3) achieving component durability in the demanding environment of an operating gas turbine. Additive manufacturing (AM) accelerates product development, yet concerns persist regarding the durability of parts with rough AM surfaces. A fully experimental approach to quantify the fatigue performance of rough AM microstructures is both costly and labor-intensive. To address this, ORNL and Solar Turbines Incorporated (Solar) employed a crystal plasticity finite element (CPFE) model to identify the factors influencing AM surface fatigue behavior. These CPFE findings, combined with targeted experimental data, were used to develop a computationally efficient surrogate model suitable for assessing the lifespan of gas turbine engine components.

08 HYDROGEN↗

Investigation on Strength, Ductility and Electrical Conductivity of Cu-4Ag Alloy Prepared by Cryorolling and Subsequent Annealing Process

Cu-Ag alloy is widely used as conductive material for high-field pulsed magnets in electrical industry. The cryorolling technique is considered as the most applicable severe plastic deformation technique. Therefore, in this study, cryorolling and subsequent annealing process were used to prepare Cu-4Ag (in wt.%) alloy sheets. The strength, ductility and electrical conductivity of Cu-4Ag alloy sheets were investigated. Microstructure of Cu-4Ag alloy was also studied by OM, SEM, XRD and TEM. As a result, the cryorolling specimens after annealing at temperature of 300 °C display a good combination of tensile strength of 652.2 ± 6.0 MPa, moderate elongation of 12.5 ± 0.7% and electrical conductivity of 80.6 ± 0.2% IACS. This is due to the presence of dislocations, dislocation cells, nanograins and nanotwins in the non-recrystallized regions and fine nanoscaled silver precipitates. Besides, a good ductility is achieved in this condition due to its desirable ductile fracture characteristics.

36 MATERIALS SCIENCE↗

Recent advances in enzyme engineering for improved deconstruction of poly(ethylene terephthalate) (PET) plastics

In the last ~20 years, a multitude of natural enzymes have been discovered that can catalyze the breakdown of the common plastic poly(ethylene terephthalate) (PET). While enzymatic PET recycling is an attractive alternative end-of-life route for this waste plastic, the enzymes are not yet optimized for efficient and economical industrial use. Here, we discuss recent advances in engineering these PET-degrading enzymes, which include PET, bis(2-hydroxyethyl) terephthalate (BHET), and 2-hydroxyethyl terephthalic acid (MHET) hydrolases, toward industrially-relevant engineering goals. We place emphasis on trends from past efforts in rational and semi-rational design and emerging areas in directed evolution/high throughput screening and computational design for engineering these enzymes.

54 ENVIRONMENTAL SCIENCES↗

Absolute dosimetric characterization of Gafchromic EBT3 and HDv2 films using commercial flat-bed scanners and evaluation of the scanner response function variability

Radiochromic films (RCF) are commonly used in dosimetry for a wide range of radiation sources (electrons, protons, and photons) for medical, industrial, and scientific applications. They are multi-layered, which includes plastic substrate layers and sensitive layers that incorporate a radiation-sensitive dye. Quantitative dose can be retrieved by digitizing the film, provided that a prior calibration exists. Here, to calibrate the newly developed EBT3 and HDv2 RCFs from Gafchromic™, we used the Stanford Medical LINAC to deposit in the films various doses of 10 MeV photons, and by scanning the films using three independent EPSON Precision 2450 scanners, three independent EPSON V750 scanners, and two independent EPSON 11000XL scanners. The films were scanned in separate RGB channels, as well as in black and white, and film orientation was varied. We found that the green channel of the RGB scan and the grayscale channel are in fact quite consistent over the different models of the scanner, although this comes at the cost of a reduction in sensitivity (by a factor ∼2.5 compared to the red channel). To allow any user to extend the absolute calibration reported here to any other scanner, we furthermore provide a calibration curve of the EPSON 2450 scanner based on absolutely calibrated, commercially available, optical density filters.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Carbon Nanotube and Graphene Oxide Reinforced Composites for Lightning Strike Protection of Composite Structures

Carbon fiber reinforced plastics (CFRP) composites have become the primary materials in the aerospace industry. Future transportation means, such as urban air mobility (UAM), will be employing CFRP structures. However, lightning strike damage on composite structures is a serious concern. CFRP composites possess low through-thickness electrical conductivity (≈ 1 S/m), which can cause extreme resistive heat in the event of lightning strikes. Research on polymeric lightning strike protection has gained momentum in the past few years. Researchers have studied various conductive fillers to improve the CFRP performance against lightning strikes. Carbon nanotubes (CNTs) and graphene oxide (GO) have been studied as future lightning Strike Protection (LSP) materials the most. The use of CNT and GO-based composites has shown improved mechanical properties and improved electrical conductivity of the composites. Researchers investigated CNTs and GO as the fillers to the matrix system, sizing the carbon fibers and the surface coating on top of the CFRP surface. This chapter highlights the remarkable improvement in the lightning damage suppression of CNT and GO-based composites and their structural applications. Special attention is given to their potential use as LSP material in future aircraft.

Kumar, Vipin↗

Moving to Sustainable Metals: Multifunctional Ligands in Catalytic, Outer Sphere C-H, N-H and O-H Activation

Much of our work during this grant period has emphasized green chemistry and sustainability. For example, we were able to convert glycerine, a waste byproduct of biodiesel production, into lactic acid, a compound with numerous applications, notably in the food and cosmetics industry, as well as being a source material for a biodegradable plastic. This work required a catalyst, that ceases to work after a certain lapse of time. We were able to identify the way in which this deactivation occurs by identifying some of the metal catalyst deactivation products. These proved to be multimetallic clusters containing up to six metals and up to 14 hydrogen atoms. Both the catalytic reaction itself and the deactivation structures are novel and unexpected. We have previously proposed that nitrogen heterocycles could be good energy carriers in a low CO 2 future world. In another part of our study, we found catalysts for introduction of hydrogen, an energy carrier that is hard to store, into nitrogen heterocycles. The mechanism of this process proved to be unusual in that the catalyst transfers the H 2 to the heterocycle in the form of H + and H - , first transferring the H + and only then the H - . In a third area of study, some of our compounds, originally prepared for DOE catalysis purposes, also proved useful in hydrocarbon oxidation and in water oxidation. The latter is important in solar-to-fuel work, because, by analogy with natural photosynthesis, the goal of the Yale Solar Group of four PIs is to convert sunlight to hydrogen and oxygen, which requires water splitting catalysts. The catalysts that proved useful mediate the latter reaction: water oxidation to oxygen. In a more technical study, we developed methods for distinguishing the case where catalysis is mediated by a soluble catalyst from cases where catalysis arises from a deposit of finely divided solid. One particular application involved electrocatalysis, where catalysis is driven by application of a voltage to electrodes dipped in the reactant mixture. We measured the mass increase of an electrode as material is deposited, and were able to see how this process is affected by the voltage supplied to the electrode. Our work continues to be well cited and we often receive requests for information or samples from fellow researchers.

08 HYDROGEN↗

NASA Tech Briefs, June 2013

Topics include: Cloud Absorption Radiometer Autonomous Navigation System - CANS, Software Method for Computed Tomography Cylinder Data Unwrapping, Re-slicing, and Analysis, Discrete Data Qualification System and Method Comprising Noise Series Fault Detection, Simple Laser Communications Terminal for Downlink from Earth Orbit at Rates Exceeding 10 Gb/s, Application Program Interface for the Orion Aerodynamics Database, Hyperspectral Imager-Tracker, Web Application Software for Ground Operations Planning Database (GOPDb) Management, Software Defined Radio with Parallelized Software Architecture, Compact Radar Transceiver with Included Calibration, Software Defined Radio with Parallelized Software Architecture, Phase Change Material Thermal Power Generator, The Thermal Hogan - A Means of Surviving the Lunar Night, Micromachined Active Magnetic Regenerator for Low-Temperature Magnetic Coolers, Nano-Ceramic Coated Plastics, Preparation of a Bimetal Using Mechanical Alloying for Environmental or Industrial Use, Phase Change Material for Temperature Control of Imager or Sounder on GOES Type Satellites in GEO, Dual-Compartment Inflatable Suitlock, Modular Connector Keying Concept, Genesis Ultrapure Water Megasonic Wafer Spin Cleaner, Piezoelectrically Initiated Pyrotechnic Igniter, Folding Elastic Thermal Surface - FETS, Multi-Pass Quadrupole Mass Analyzer, Lunar Sulfur Capture System, Environmental Qualification of a Single-Crystal Silicon Mirror for Spaceflight Use, Planar Superconducting Millimeter-Wave/Terahertz Channelizing Filter, Qualification of UHF Antenna for Extreme Martian Thermal Environments, Ensemble Eclipse: A Process for Prefab Development Environment for the Ensemble Project, ISS Live!, Space Operations Learning Center (SOLC) iPhone/iPad Application, Software to Compare NPP HDF5 Data Files, Planetary Data Systems (PDS) Imaging Node Atlas II, Automatic Calibration of an Airborne Imaging System to an Inertial Navigation Unit, Translating MAPGEN to ASPEN for MER, Support Routines for In Situ Image Processing, and Semi-Supervised Eigenbasis Novelty Detection.

Source record↗

Characterization of Prepreg Tack for Composite Manufacturing by Automated Fiber Placement

Automated fiber placement (AFP) has become the industry standard for large-scale production of carbon fiber reinforced plastics (CFRP) to improve rate and reduce defects associated with manual layup. Still, defects generated during AFP processes require manual, painstaking inspection by technicians and rework of the part when substantial defects are found. Prepreg (carbon fiber infused with uncured epoxy resin) tack is one of the primary factors that influences the generation of defects that arise during auto-mated fiber placement (AFP). Tack, as it relates to AFP processes and defect formation, can be understood as a combination of two stages, cohesion and decohesion. During the cohesion phase, two pieces of prepreg are brought into contact under elevated temperature and pressure. Compaction of the resin within the contact area will result in a degree of intimate contact, I, between the mating prepreg surfaces. Defect formation, as a result of decohesion between prepreg surfaces, occurs after the cohesion phase and arises due to stress from events such as fiber placement over an existing defect, on a contoured path, etc. (Figure 1). Tack strength resists the displacement of prepreg on a surface due to stresses developed during deposition.

Wohl, Christopher J↗

Characterizing Char Rate and Extent in Fiber-Reinforced Plastics Using X-ray Computed Tomography

Orbital debris is a growing problem for the space industry and the world in general, and an important component of the problem is what happens when that debris reenters the Earth’s atmosphere. With more spacecraft opting for fiber-reinforced polymer (FRP) components, we need to understand the thermal destruction process of these materials during an atmospheric reentry and how much of the material can survive to impact the ground. The NASA Orbital Debris Program Office (ODPO) has developed a new charring model for FRP components to be integrated into the latest version of the Object Reentry Survival Analysis Tool (ORSAT). To validate this new model, the ODPO performed several test series using the Inductively Coupled Plasma (ICP) Torch facility at UT Austin. To measure the extent of charred material at different conditions, some of the test samples were scanned using x-ray computed tomography (CT) by the Astromaterials Curation Lab at Johnson Space Center. 3D image analysis was then used to calculate the volume and density of the char in each test sample. This paper presents the image analysis methodology, an assessment of the accuracy of the data analysis, and a comparison with calculations using the ORSAT charring model.

Benton Greene↗

NETL Plastic Pipes Project (Final Report)

Plastic or composite pipelines have been the bane of the utility locating industry because they are neither conductive nor magnetic which are the properties traditionally used to locate buried utilities. Ground penetrating radar (GPR) is an effective geophysical tool for locating plastic/composite pipelines where resistive cover allows for adequate penetration of radar energy. However, GPR has limited applicability in areas where the soil cover is conductive due to significant clay and/or salt content. This study examines complementary near-surface geophysical methods that are potentially useful for locating buried plastic/composite pipelines, either singly or in combination. Specifically, this modeling study used computational numerical methods to forward model the response of GPR, resistivity, seismic, gravity gradiometry, and photoacoustic/thermoacoustic imaging methods to plastic/composite pipelines for various scenarios including: (1) pipe diameters ranging between 2 in. to 12 in.; (2) burial depths ranging between 3 ft. to 4 ft.; (3) various degrees in contrast in physical properties (i.e., electrical permittivity, elasticity, resistivity, density); and (4) various experimental acquisition choices (e.g., GPR radar and seismic source frequencies, electrode spacing). Numerical modeling performed herein reconfirmed that GPR is the preferred method for detecting/locating plastic pipelines. A caveat for GPR detection is that the material covering the plastic pipe (trench fill material and adjacent soil) must be sufficiently resistive to allow the two-way propagation to the required depth of investigation and back to the surface. GPR was the only method modeled in this study that can be used to directly detect plastic pipelines of 2-in.-diameter and larger when buried 3-ft-deep. GPR data processing and imaging also can determine pipe depth, pipe diameter, trench dimensions, and moisture conditions. Seismic modeling results suggest that direct detection of a 12-in.-diameter plastic pipe at 3-ft.-depth may be possible under favorable conditions; however, the associated signature would be weak (e.g., surface- to S-wave, backscattered surface-waves, and/or forward scattered surface-waves to S-wave). Direct pipe detection under field conditions with noise and strong lateral geologic heterogeneity is doubtful. Numerical modeling also suggests that plastic pipelines can be indirectly located by detecting the trench in which they are buried. GPR, direct current (DC) resistivity, and seismic methods have the potential to locate the pipeline trench if there is sufficient contrast between the trench-wall and trench-fill materials for the physical property being measured by each method (i.e., electrical permittivity for GPR; resistivity for DC resistivity; or density, compressional velocity, or shear velocity for seismic). Modeling also indicated that currently available (commercial) gravity gradiometers would be unable to directly detect/locate plastic pipelines ≤ 8-in.-diameter when buried 3-ft.-deep given the typical instrument noise floor for field surveying as well as the expected density variations due to geologic heterogeneity. The numerical modeling performed in this project did not identify a universal geophysical technology that can locate buried plastic pipelines in all parts of the United States (although GPR is suggested for all areas with resistive cover). However, the project results suggest that a towed land streamer simultaneously acquiring multiple geophysical data types including multi-offset GPR, multi-channel DC resistivity, seismic geophone- and/or distributed acoustic sensing (DAS), and potentially photoacoustic/thermoacoustic data would be an appropriate platform for locating buried plastic pipeline. Moreover, the complementary multiphysics data acquired by a towed land streamer would permit the use of joint and/or cooperative inversion frameworks for a more rigorous and consistent data interpretation.

42 ENGINEERING↗

Interplay Between Plastic Deformations and Optical Properites of Metal Surfaces: A Multiscale Study

The design of metallic surfaces with required surface quality and visual appearance represents a significant challenge for scientists and engineers. For example, the surface of aluminum products such as reflector bright sheet, aerospace structural components, and architectural materials is always required to have an attractive appearance under different lighting conditions and to be free of defects and corrosion [ref. 1]. Industrial-scale modification processes of metal alloy products (heat treatment, rolling, stretching, extruding, etc.) are closely related to different plastic phenomena. Although plastic deformation takes place at the macroscopic level, it significantly changes the surface geometry at the meso- and microscopic scales which may result in spectacular modifications of visual appearance of the deformed surface. Here we use a combination of confocal optical microscopy, orientation imaging microscopy with electron back scattering diffraction (EBSD), original morphological image analysis approach developed by the authors, and finite element simulations, in order to investigate the interplay of different plastic instabilities emerging in the course of plastic deformation, and visual appearance. It is demonstrated that visual brightness of aluminum sheet products could be significantly suppressed by some widely used industrial processes such as uniaxial stretching of the sheet. On the other hand, a properly designed “texture rolling” (i.e., embossing additional controlled engineered features into the metal surface) makes it significantly brighter than a conventionally rolled surface because these features may serve as sinks for otherwise incompatible plastic deformations and enhance brightness due to the suppression of roughness. It is expected that such “imaging transitions” are of general nature and could be observed for different metals and alloys exhibiting plastic instabilities. In turn, these results provide guidelines for the control of metal surface morphology in order to achieve desirable visual appearance, such as visual brightness and omnidirectional coloration.

36 MATERIALS SCIENCE↗