Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Effect of Molybdenum Content on Structural, Mechanical, and Tribological Properties of Hot Isostatically Pressed β-Type Titanium Alloys for Orthopedic Applications

Aiming to develop alloys with better properties for orthopedic applications, the focus of the present research was to evaluate the effect of Mo at.% content on structural, mechanical, and tribological properties of hot isostatically pressed Ti-xMo (x = 4, 8, 12, 15, and 20 at.%) alloys. The structural evolution, mechanical properties, and tribological behavior of the nanostructured Ti-xMo alloys were evaluated using x-ray diffraction, scanning electron microscope, and ball-on-disk tribometer. Wear tests were conducted under different applied loads of 2, 8, and 16 N. Experimental results indicated that the structural evolution and morphological changes of the milled alloys were sensitive to their molybdenum (Mo) content. The morphological characterization showed that the crystallite size and the particle size decreased with increasing Mo content (at.%) reaching the lowest values of 27 and 26 nm in the case of Ti-15Mo and Ti-20Mo, respectively. On the other hand, the coefficient of friction and wear rates were found to be decreasing with increasing Mo content.

36 MATERIALS SCIENCE↗

ASSESSMENT OF RESIDUAL STRESSES ON U10MO ALLOY BASED MONOLITHIC MINI-PLATES DURING HOT ISOSTATIC PRESSING

This article presents an assessment of the residual stress field on U10Mo alloy based monolithic fuel plates and their elasto-plastic response to the thermo-mechanical fabrication process. Monolithic plate-type fuel for research and test reactors is a new fuel form proposed and developed by Idaho National Laboratory (INL) to accomplish higher uranium densities in the reactor core and allow multi-fold reduction of fuel enrichment. Identification of the 3D residual field is critical for benchmarking the new design and understanding the overall performance of the new plate-type fuels. To define fuel-cladding stress-strain characteristics, a new thermo-mechanical finite element model was developed. Material properties at high temperatures and material plasticity were considered carefully to improve the accuracy as the Hot Pressing temperature reaches the melting temperature of the cladding material. By using elasto-thermo-plastic material models, it was determined that the cladding material (AL6061-TO) is exposed to tensile stress field and exceeds its proportional limits, while the fuel foil (U10Mo) is under compression and remains below its yield limit. It was shown that the residual stresses would govern the overall behavior of the plates, and therefore, should not be neglected. In particular, the simulations have revealed the existence of stress gradients at the fuel/cladding interface, thus emphasizing the necessity of excellent bonding quality at the bond region for mechanical endurance.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

An Initial Evaluation of the Elevated-Temperature Cyclic Properties of Optimized 316H Stainless Steel Fabricated by Powder Metallurgy Hot Isostatic Pressing

Powder metallurgy hot isostatic pressing (PM-HIP) is a mature advanced manufacturing technology, which can consolidate metallic powder under high temperature and pressure to generate near-net shape components. This process can lower production costs and reduce component lead times for nuclear reactor construction and can be readily deployed in the near term for microreactor components because of their smaller size. The purpose of this work is to continue the evaluation of elevated-temperature cyclic material properties for PM-HIP 316H stainless steel. Prior scoping results have shown that the commercially procured PM-HIP stainless-steel materials have reduced creep-fatigue performance compared to wrought 316 stainless steels. To better understand how PM-HIP processed material properties compare to traditional manufacturing methods, additional billets of PM-HIP 316H stainless steel were procured and tested. This testing is necessary to understand how elevated-temperature properties are influenced by the PM-HIP process and what data are needed for incorporating PM HIP 316H into the American Society of Mechanical Engineers Boiler Pressure Vessel Code, Section III, Division 5 for high temperature reactor construction. Specifically, an additional PM-HIP 316H stainless steel billet with lower oxygen and nitrogen concentrations was fabricated by the Nuclear Advanced Manufacturing Research Centre of the United Kingdom and tested to understand if elevated-temperature cyclic properties can be improved. The creep-fatigue resistance of the material from this new billet did not show appreciable improvement compared to prior testing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of the Pressing Characteristics of Commercially Pure Titanium Using an Instrumented Double Acting Die

With recent advances in synthesizing titanium powder by low-cost routes, there has been growing interest in identifying process/material conditions that overcome the powder compaction problems typically found with this reactive metal. The use of instrumented dies in studying the cold pressing process for commercial iron and steel powders has provided greater insight into the complex phenomena that occur and may be used to evaluate constitutive relations that describe the compaction process. Nevertheless, little work has been conducted on the special, more problematic case of reactive metal powders such as titanium. An instrumented die was developed that allows die wall friction to be characterized and the radial stress distribution along the die wall and throughout the compact to be monitored. As will be presented, this tool has been used to investigate titanium compaction and to draw comparisons with results obtained on a baseline commercial iron powder. Both sets of data were systematically collected using various powder/die lubrication combinations.

36 MATERIALS SCIENCE↗

Understanding Oxide–Metal Interactions During Hot Isostatic Pressing to Diffusion Bond Aluminum Alloy 6061 Plates

The interaction between Mg, Si, and Al 2 O 3 during hot isostatic pressing diffusion bonding of aluminum alloy 6061 (AA6061) plates was investigated through thermodynamic calculations and experimental microstructural characterization. Thermodynamic calculations as functions of temperature, pressure, and composition revealed that the interaction among Mg, Si, and Al 2 O 3 yields Mg 2 Si and either MgO + Al or MgAl 2 O 4 + Al, facilitating the reduction of Al 2 O 3 and allowing Al/Al metallic bonds to form. Total pressure variation had a negligible influence on the oxygen partial pressure, and consequently, the reaction product formation. Oxygen partial pressure variation as a function of temperature and initial amount of Al 2 O 3 determined the formation of either MgO or MgAl 2 O 4 . Experimental Hot Isostatic Pressure (HIP) bonding at 723 K and 833 K under a constant pressure of 1017 atm documented the cooling rate-dependent formation of β–Mg 2 Si precipitates. High-resolution transmission electron microscopy imaging and selected area electron diffraction patterns verified the formation of β–Mg 2 Si and MgO at the interface but did not detect MgAl 2 O 4 . In conclusion, findings from this study clarify the role of thermochemical interactions in oxide disruption and bonding mechanisms during HIP diffusion bonding of AA6061 and provide guidance for optimizing joining processes for monolithic nuclear fuel assemblies.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Workability Limits of Magnesium Alloy AZ31B Subjected to Equal Channel Angular Pressing

Equal channel angular pressing (ECAP) is an important severe plastic deformation process to produce ultrafine grained microstructures in metals and alloys. Magnesium and its alloys generally possess poor workability at temperatures below 250 °C. This investigation examines the influence of different passes and processing routes of ECAP on improving the workability of Mg alloy AZ31B. ECAP was carried out for three passes using a die of angle 120° using processing routes Bc and C. The operating temperature was 523 K for the first pass and 423 K for the subsequent two passes. The resultant microstructure and mechanical properties were determined. Workability of the alloy at 423 K (150 °C) was determined using upsetting experiments on cylindrical specimens machined from the annealed and ECAPed samples. Workability limit diagrams have been constructed for the various processed conditions. The workability data generated were also analyzed using five different workability criteria (also referred to as ductile fracture models) and the material constants for these five models were evaluated. Specimens processed by two passes through route C (pass 2C) exhibits better workability compared to other passes since the workability limit line after this pass shows maximum safe working area and lies above the other workability lines. Among the five different workability criteria investigated, the Freudenthal workability criterion is more suitable for prediction of failure in this alloy.

36 MATERIALS SCIENCE↗

Experimental and Numerical Analyses of the Consolidation Process of AA 7075–2 wt.% ZrO{sub 2} Powders by Equal Channel Angular Pressing

AA7075 matrix composite was obtained by mechanical alloying using ZrO{sub 2} particles as reinforcement. After that, the powders were cold-compacted into an aluminum tube and consolidated by equal channel angular pressing at 220 °C. The temperature influence was analyzed, and it was found by scanning electron microscopy that this route gave the minimum pore percentage. Besides, it was noticeable that the hardness was wide superior in comparison with the AA 7075 aged bulk alloy. In addition, there was no evidence of any chemical reaction between ZrO{sub 2} and alloying elements at the temperature employed. On the other hand, it was numerically and experimentally demonstrated that the more strained regions exhibited a higher relative density values.

36 MATERIALS SCIENCE↗

Performance of Nd-Fe-B Magnets Fabricated by Hot Isostatic Pressing and Low-Temperature Sintering

Magnetic properties and microstructure of Nd-Fe-B sintered magnets fabricated by hot isostatic pressing (HIP) were studied. For comparison, magnets were also fabricated by vacuum sintering. The density reached 7.58 g/cm{sup 3} for the magnets HIP-sintered at 1123 K. The density of the magnets vacuum-sintered at 1123 K was much lower, which is of about 6.92 g/cm{sup 3}. While the density of magnets vacuum-sintered at 1318 K was the same as the HIP-sintered magnets, the sintering temperature was significantly decreased to 1123 K. In addition, the average grain size decreased from 9 to 6 μm, which has enhanced coercivity. Therefore, the coercivity increased from 1067.7 to 1238.5 kA/m, which is 16% higher than the vacuum-sintered magnets. HIP is a promising method to obtain high density and high coercivity Nd-Fe-B sintered magnets.

36 MATERIALS SCIENCE↗

Investigation on Equal-Channel Angular Pressing-Induced Grain Refinement in an Aluminum Matrix Composite Reinforced with Al-Cu-Ti Metallic Glass Particles

In the present study, a homogeneous ultrafine grain structure composite consisting of metallic glass particles reinforcements was developed by equal-channel angular pressing (ECAP) process. The microstructure of composite was characterized using x-ray diffraction (XRD), transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD) techniques. The uniaxial compression test was used to determine the mechanical properties. The mechanisms of grain refinement during ECAP process were discussed based on the microstructural evolutions. A composite was successfully produced after four passes of ECAP, having an average grain size of 610 nm and compressive yield strength of 242 MPa. Also, the yield strength of composite after each pass was quantitatively estimated by considering all the effective strengthening mechanism. The findings showed that the dislocations strengthening mechanism with contribution of more than 50% plays a major role in strengthening the composite. There was a negligible gap between the experimental and theoretical values of yield strength for all ECAP pass numbers.

36 MATERIALS SCIENCE↗

Fabrication, Microstructures, and Properties of 50 vol.% SiCp/6061Al Composites via Hot Pressing

Nearly fully dense 50 vol.% SiCp/6061Al composites were fabricated via hot pressing (HPing) at temperatures ranging from 610 to 650 °C, with the axial load and holding time fixed as 25 MPa and 120 min, respectively. The interfacial reactions, microstructures, and properties of the SiCp/Al alloy were studied. The interface reaction between SiCp and the Al alloy was suppressed at annealing temperatures of 620 °C and below; however, the reaction intensified as the annealing temperature increased, producing Al{sub 4}C{sub 3}, Si, and Mg{sub 2}Si. With an increase in HPing temperature from 610 to 630 °C, the 6061Al alloy melted and gradually filled the pores in the SiC particles under the applied load. The density, bending strength, and thermal conductivity (TC) of the composites increased, whereas the coefficient of thermal expansion (CTE) of the composites decreased. With an increase in HPing temperature increased from 630 to 650 °C, the 6061Al alloy melt leaked through the sintered bodies, resulting in the microstructural degradation and property reduction of the composites. The 50 vol.% SiCp/6061Al composites fabricated by HPing at 630 °C exhibited optimal comprehensive properties [bending strength, 332.4 MPa; TC, 186.3 W(m K){sup −1}; and CTE, 7.9 × 10{sup −6}/°C (20-100 °C)], which were attributed to the highest relative density and the best SiCp/Al interfacial structure of the composites.

36 MATERIALS SCIENCE↗

Development of Texture in Ultrafine-Grained Low-Carbon Steel Processed through Equal-Channel Angular Pressing

Developments of microstructures and texture are investigated for a low-carbon steel deformed by equal-channel angular pressing (ECAP) at room temperature for equivalent strain (ε{sub vm}) of 16.8. ECAP at ε{sub vm} = 0.6 reduces grain size by two orders of magnitude. With increasing strain, grain size reduces further and high-angle grain boundary (HAGB) fraction improves by grain subdivision and its change in orientation. ECAP of low-carbon steel up to ε{sub vm} = 16.8 can produce ultrafine grains of 0.2 µm size with HAGB fraction of 82%. The as-received steel has low texture index. Microstructural changes strongly influence texture development. It increases with equivalent strain as grain subdivision continues. Texture index fluctuates at intermediate strain range due to randomization of initial texture. Texture index reaches saturation at the high equivalent strain. On ECAP at low to intermediate strain ε{sub vm} = 0.6-6, components of both α (F{sub θ}, J{sub θ}, and J-bar {sub θ}) and γ (D{sub 1θ}, D{sub 2θ}, and E{sub θ}) fibers are developed though all of them deviate from their ideal positions. At higher strain (ε{sub vm} = 9-16.8), the γ fiber components (D{sub 1θ}, D{sub 2θ}, E{sub θ}) are strengthened, and the E{sub θ} component reaches the highest intensity of ≈ 17 at ε{sub vm} = 12. There is no texture symmetry at low to high strain level. The presence of pearlite in low-carbon steel enhances strongly the deviation of texture components from their ideal positions in Euler’s space as well as it increases the intensities of the components more than that of IF steel for a similar equivalent strain.

36 MATERIALS SCIENCE↗

An Investigation on Microstructure Evolution, Mechanical Properties, and Strain Aging of Mg-1.8Zn-0.7Si-0.4Ca Biomedical Alloy Processed by Equal Channel Angular Pressing

The influence of equal channel angular pressing (ECAP) on microstructure and mechanical behavior, as well as, strain aging during ECAP and post-ECAP of Mg-1.8Zn-0.7Si-0.4Ca biomedical alloy was examined. The alloy in solid solution heat-treated condition was processed by ECAP with route B{sub C} at 350 and 400 °C. The specimens ECAPed at 350 °C were aged at 125 and 150 °C for different times. The hardness and shear punch test results indicated that performing ECAP at 350 °C for 4 passes increases the hardness and shear strength of the alloy from 48 HV and 110 MPa to 71 HV and 188 MPa, respectively. It was revealed that the average grain size of the alloy decreases from 78 µm to about 3 µm after 4 passes of ECAP. Three precipitates of CaMgSi, Ca{sub 2}Mg{sub 6}Zn{sub 3}, and Mg{sub 2}Si were detected in the solid solution specimen. After 4 passes of ECAP at 350 °C, Ca{sub 2}Mg{sub 6}Zn{sub 3} was completely dissolved and the morphology of Mg{sub 2}Si changed from Chinese script to fiber-shaped particles. Dynamic strain aging occurred at high-temperature ECAP, and the specimens were overaged during post-ECAP aging. Small MgZn particles were detected in the overaged sample.

36 MATERIALS SCIENCE↗

An innovative radial gradient material design using hot isostatic pressing for applications in extreme environments

Functionally graded materials (FGMs) are highly advanced continuous or discontinuous structures whose structural and material properties vary along a singular geometric dimension either in the axial or radial direction. Here, the radial gradient FGM design makes for an optimal structural design to incorporate a bi-metallic structure with a copper-based high entropy alloy (Cu-HEA) with good mechanical properties and high irradiation resistance, and Chromium (Cr) with great corrosion resistance. This study focuses on the experimental design of a metal powder loading mechanism to fabricate a bi-metallic radial gradient structure using Cu-HEA and 99.9 % pure Cr metal powders. The powder loading strategy uses custom-designed concentric cylindrical dividers to separate the individual compositions. Two benchtop trial runs were performed for design optimization. The optimized design was then implemented to eventually load the HEA and Cr powders for consolidation via powder metallurgy hot isostatic pressing (PM-HIP). The electron microscopy analysis reveals the successful fabrication of the radial gradient structure with the chemical mapping analysis, demonstrating the gradual composition shift from the HEA at the center to the pure-Cr at the periphery via a three-step gradient.

High Entropy Alloys (HEAs)↗

Binder-jetted AISI M2 tool steel during hot isostatic pressing: Densification and carbide transformation

Binder jetting (BJ) enables fabrication of complex components from high-alloy steels such as AISI M2; however, residual porosity after sintering limits mechanical performance. This study investigates the coupled effects of binder chemistry, sintering conditions, cooling rate, and subsequent hot isostatic pressing (HIP) on densification, microstructure, and mechanical response in binder-jetted M2 tool steel. HIP increased relative density from ∼93 to 95% to >99% and improved compressive strength by ∼40-70%. Densification was governed by initial pore morphology, where closed porosity was effectively eliminated, while interconnected porosity limited full consolidation. Microstructural analysis (XRD, EBSD, SEM) shows that HIP promotes dissolution of metastable carbides and redistribution of alloying elements (W, Mo, V), transforming heterogeneous carbide networks into finer and more uniformly distributed M 2 C, MC, and M 6 C phases through diffusion-assisted homogenization. Among the investigated conditions, the FluidFuse binder combined with sintering at 1270 °C for 60 min and furnace cooling produced the most balanced response, achieving ∼99.7% density, ∼855 HV hardness, ∼4130 MPa compressive strength, and ∼24% strain. In contrast, higher sintering temperatures promoted carbide coarsening, reducing ductility despite high density. HIP reduces microstructural heterogeneity and drives the system toward a near-equilibrium state with reduced sensitivity to prior processing history. A comparative assessment with conventional and additive manufacturing routes (LPBF, DED, EBM, FFF) shows that the BJ-HIP approach achieves competitive densification and mechanical performance. These findings provide a mechanistic basis for controlling densification and microstructure in high-alloy steels processed via BJAM.

AISI M2 tool steel↗

Growth kinetics and microstructural evolution during hot isostatic pressing of U-10 wt.% Mo monolithic fuel plate in AA6061 cladding with Zr diffusion barrier

Phase constituents and microstructure changes in RERTR fuel plate assemblies as functions of temperature and duration of hot-isostatic pressing (HIP) during fabrication were examined. The HIP process was carried out as functions of temperature (520, 540, 560 and 580 °C for 90 min) and time (45–345 min at 560 °C) to bond 6061 Al-alloy to the Zr diffusion barrier that had been co-rolled with U-10 wt.% Mo (U10Mo) fuel monolith prior to the HIP process. Scanning and transmission electron microscopies were employed to examine the phase constituents, microstructure and layer thickness of interaction products from interdiffusion. At the interface between the U10Mo and Zr, following the co-rolling, the UZr2 phase was observed to develop adjacent to Zr, and the a-U phase was found between the UZr2 and U10Mo, while the Mo2Zr was found as precipitates mostly within the a-U phase. The phase constituents and thickness of the interaction layer at the U10Mo-Zr interface remained unchanged regardless of HIP processing variation. Observable growth due to HIP was only observed for the (Al,Si)3Zr phase found at the Zr/AA6061 interface, however, with a large activation energy of 457 ± 28 kJ/mole. Thus, HIP can be carried to improve the adhesion quality of fuel plate without concern for the excessive growth of the interaction layer, particularly at the U10Mo-Zr interface with the a-U, Mo2Zr, and UZr2 phases.

99 GENERAL AND MISCELLANEOUS↗

Micro-tensile testing of the bond line in hot isostatic pressed aluminum

Considerable effort is being devoted to development and regulatory qualification of low enriched fuels for research and test reactors by many agencies worldwide. One promising fuel configuration being examined for United States higher power research and test reactors (USHPRRs) are plate-type fuels composed of a metallic uranium-molybdenum foil clad in an aluminum alloy. The two pieces of aluminum alloy cladding are bonded using a hot isostatic pressing method. The mechanical properties of the resulting bond line in the aluminum alloy cladding will vary by the HIP'ing parameters, requiring a need to characterize the bond line. Small scale mechanical testing can provide a path for evaluating the mechanical properties and deformation behavior of the bond line both prior to and following irradiation. Here, in this research, room temperature micro-tensile specimens of non-irradiated and irradiated samples containing an Al alloy (AA 6061) bond line were tested to evaluate its strength and deformation behavior. Observations indicated that the strain rate did not affect the deformation behavior or strength and most of the micro-tensile specimens failed in a ductile mode in grains around the bond line. There was no indication that the microstructural features from the bond line affected the mechanical properties of the micro-tensile specimens. An initial examination was performed on irradiated material but further systematic studies of the effects of irradiation can be performed in the future.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Insight into the interfacial microstructure and chemistry of hot isostatically pressed AA6061-AA6061 bonds for U-10Mo fuel cladding application

Here, in the present study, hot isostatic pressing (HIP) bonding was carried out using AA6061-AA6061 plates for U-10Mo monolithic fuel cladding application. HIP was performed at 560°C with an applied isostatic pressure of 103 MPa for 90 min. Interfacial microstructure characterizations were performed using scanning electron microscopy (SEM) combined with electron backscatter diffraction (EBSD) to quantify precipitate fractions and study recrystallization, grain growth, and orientation relationships across the interface. EBSD results confirmed that no interfacial grain growth occurred during the HIP process. Transmission electron microscopy (TEM) was also employed to quantify composition and identify phases of various precipitates and an oxide layer that formed at the interface during HIP bonding. Microstructural analyses revealed the formation of a large fraction of Mg 2 Si precipitate and a ~50 nm thick Mg-oxide layer at the interface. Further TEM analysis confirmed that the oxide layer was not continuous, and Mg 2 Al 2 O 5 oxide particles with an average size of 18 nm were present in the oxide layer. Finite element modeling analysis was performed to study the stress distribution at the interface during HIP processing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗