Search NASA⌕ Search

SEARCH · Search NASA

Results for “PROPELLER SLIPSTREAM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

176 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1942

Wind-Tunnel Tests of Four- and Six-Blade Single- and Dual-Rotating Tractor Propellers

Test of 10-foot diameter, four and six blade single-rotating and dual-rotating propellers were conducted in the NACA propeller-research tunnel. The propellers were mounted at the front end of a streamline body incorporating spinners to house the hub portions. The effect of a symmetrical wing mounted in the slipstream ranged from 20 degrees to 65 degrees setting corresponds to airplane speeds greater than 500 miles per hour. The results indicate that dual-rotating propellers were from 0 to 6 percent more efficient than single-rotating ones; but, when the propellers operated in the presence of a wing, the gain was reduced by about one-half. Other advantages of dual-rotating propellers were found to include greater power absorption and greater efficiency at the low V/nD operating range of high-pitch propellers.

Biermann, David↗
NASA NTRS1934

Contribution to the mutual interference of wing and propeller

The change of induced wing drag due to the field of flow of the propeller was analyzed quantitatively. The field of flow of the propeller is represented by a uniform distribution of sinks over the propeller disk area, whose strength is determined by the increase in speed in the slipstream. The superposition of this sink flow on the basic flow reproduces the actual field of flow outside of the slipstream with close approximation.

Wieselsberger, C↗
NASA NTRS1940

Full-Scale Tests of 4- and 6-Blade, Single- and Dual-Rotating Propellers, Special Report

Test of 10-foot diameter, 4- and 6-blade single- and dual-rotating propellers were conducted in the 20-foot propeller-research tunnel. The propellers were mounted at the front end of a streamline body incorporating spinners to house the hub portions. The effect of a symmetrical wing mounted in the slipstream was investigated. The blade angles investigated ranged from 20 degrees to 65 degrees; the latter setting corresponds to airplane speeds of over 500 miles per hour. The results indicate that dual-rotating propellers were from 0 to 6% more efficient than single-rotating ones; but when operating in the presence of a wing the gain was reduced about one-half. Other advantages of dual-rotating propellers were found to include greater power absorption and greater efficiency at the low V/nD operating range of high pitch propellers.

Biermann, David↗
NASA NTRS1941

Wind-tunnel Tests of Eight-blade Single and Dual-rotating Propellers in the Tractor Position

Tests of 10-ft. diameter, eight-blade, single - and dual - rotating propellers were conducted in 20-ft propeller research tunnel. Propellers were mounted at front end of a streamline body in spinners that covered hubs and parts of shanks. Effect of a symmetrical wing mounted in slipstream was investigated. Blade-angle settings ranged from 20 Degrees to 65 Degrees. Results indicated that dual rotation resulted in gains of from 1 to 8 percent in efficiency over single rotation for eight-blade propellers, but presence of a wing reduced gain about one-half. Greater power absorption caused by dual rotation over flight range and higher efficiency or thrust for range of take-off and climb was indicated

PROPELLER-WING COMBINATIONS↗
NASA NTRS1946

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loadings: Hamilton Standard 6507A-2 Four- and Three-Blade Propellers - 6

An altitude-wind-tunnel investigation has been made to determine the performance of Hamilton Standard 6507A-2 four-blade and three-blade propellers on a YP-47M airplane at high blade loadings and high engine powers. Characteristics of the four-blase propeller were obtained for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.20, 0.30, 0.40. Characteristics of the three-blade propeller were obtained for a range of power coefficients from 0.30 to 1.00 at a free-stream Mach number of 0.40. Results of the force measurements indicate primarily the trend of propeller efficiency for changes in power coefficient or advance-diameter ratio because no corrections for the effects of tunnel-wall constriction on the installation were applied. Slipstream surveys are presented to illustrate blade thrust load distribution for certain operating conditions. Within the range of advance-diameter ratios investigated at each free-stream Mach number, the efficiency of the four-blade propeller decreased as the power coefficient was increased from 0.10 to 1.00. For the three-blade propeller, nearly constant maximum efficiencies were obtained for power coefficients from 0.32 to 0.63 at advance-diameter ratios between 1.90 and 3.00. In general, for conditions below the stall and critical tip Mach number, the maximum thrust load shifted from the inboard sections toward the tip sections as the power coefficient was increased or as the advance-diameter ratio was decreased. For conditions beyond the stall or critical tip Mach number, losses in thrust occurred on the outboard blade sections owing to flow break-down; the thrust load increased slightly on the inboard sections.

Saari, Martin J.↗
NASA NTRS1940

Longitudinal stability and control with special reference to slipstream effects

Report presents the results of a study of data obtained in the NACA full-scale wind tunnel concerning the effects of interference and of propeller operation on longitudinal stability and control. The data include pitching moments for various power conditions for airplanes with tails removed and with tails set at various stabilizer and elevator angles. A number of surveys of the dynamic pressure and the flow direction in the region of the horizontal tail surface are also included. Results are given for eight airplanes, including a model of a four-engine airplane tested both as a tractor and as a pushed and a model of two-engine pusher. The effects are shown of propeller operation on the downwash angles and the dynamic pressures at the tail and on the pitching-moment contribution of the propeller and the wing.

Katzoff, S↗
NASA NTRS1946

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loadings V - Curtiss 836-14C2-18R1 Four-Blade Propeller

An investigation of the performance of several propellers on the YP-47M airplane at high blade loadings has been conducted in the Cleveland altitude wind tunnel at the request of the Air Materiel Command, Army Air Forces. As part of the program, a study was made of a Curtiss 836-14C2-18R1 four-blade propeller. The investigation was made for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.30, 0.40, and 0.50 for density altitudes from 10,000 to 45,000 feet, engine powers from 150 to 2500 brake horsepower, and for engine speeds from 1000 to 2900 rpm. The propeller efficiencies were obtained from force measurements and the blade thrust load distribution was obtained by two diametrically opposed slipstream survey rakes shown in this paper.

Saari, Martin J.↗
NASA NTRS1975

Optimum performance and potential flow field of hovering rotors

Rotor and propeller performance and induced potential flowfields were studied on the basis of a rotating actuator disk concept, with special emphasis on rotors hovering out of ground effect. A new theory for the optimum performance of rotors hovering OGE is developed and presented. An extended theory for the optimum performance of rotors and propellers in axial motion is also presented. Numerical results are presented for the optimum distributions of blade-bound circulation together with axial inflow and ultimate wake velocities for the hovering rotor over the range of thrust coefficient of interest in rotorcraft applications. Shapes of the stream tubes and of the velocities in the slipstream are obtained, using available methods, for optimum and off-optimum circulation distributions for rotors hovering in and out of ground effect. A number of explicit formulae useful in computing rotor and propeller induced flows are presented for stream functions and velocities due to distributions of circular vortices over axi-symmetric surfaces.

Wu, J. C.↗
NASA NTRS1986

Evaluation of propeller/nacelle interactions in the PTA program

Advanced highly-loaded propellers are proposed to power transport aircraft that cruise at high subsonic speeds giving significant fuel savings over the equivalent turbofan engine. In order to realize these savings, the propeller must be installed so that the aerodynamics of the propeller/nacelle combination do not lead to excessive cyclic blade stresses or installation losses. The on-going, NASA sponsored, Propfan Test Assessment Program (PTA) has provided the first high-speed wind-tunnel data on an installed propfan complete with an inlet. This paper presents computational techniques that allow: (1) optimization of inlet plane location, (2) contouring of lip and cowl, and (3) estimation of propeller cyclic loads due to a nonuniform flowfield. These computational methods, in spite of the complexity of the configuration and the slipstream effects, provide predictions of aerodynamic performance which are in excellent agreement with wind-tunnel data.

Aljabri, A. S.↗
NASA NTRS2019

Evaluation of a Commercial Surface Vorticity Flow Solver for the Modeling of Propeller-Wing Interaction

A commercially available surface vorticity flow solver’s ability to model propeller-wing interaction effects was evaluated. First, a study was conducted to determine solution sensitivity to simulation parameters. Then, a deflected slipstream experiment was replicated with an actuator disk and wing model. Comparison with experimental data showed that predictions of lift and longitudinal force coefficients matched well at low flap deflections, but experienced offsets in magnitude with increasing flap deflection. Predictions of pitching moment differed significantly from experimental data largely due to the simple actuator disk model being insufficient for capturing the effects of non-zero flow incidence and non-uniform inflow.

Fei, Xiaofan↗
NASA NTRS1961

Aerodynamic Characteristics of Propeller-Driven VTOL Aircraft

This paper discusses the two major configurations that are usually considered for achieving VTOL while keeping the fuselage essentially horizontal - that is, the tilt-wing and the deflected-slipstream configurations. Because of the high turning losses incurred by deflected-slipstream configurations in hovering and because of the wing-stalling problem of the pure tilt-wing configurations during the transition, it appears that a combination of the two principles should be used. This tilt-wing and flap configuration should make use of a programmed extensible-chord slotted flap together with a leading-edge high-lift device in order to avoid the performance and handling qualities problems associated with wing stalling during the transition while keeping the wing area as low as possible for efficiency in cruising flight.

Kirby, Robert H.↗
NASA NTRS1939

Preliminary Tests of Blowers of Three Designs Operating in Conjunction with a Wing-Duct Cooling System for Radial Engines, Special Report

This paper is one of several dealing with methods intended to reduce the drag of present-day radial engine installations and improve the cooling at zero and low air speeds, The present paper describes model wind-tunnel tests of blowers of three designs tested in conjunction with a wing-nacelle combination. The principle of operation involved consists of drawing cooling air into ducts located in the wing root at the point of maximum slipstream velocity, passing the air through the engine baffles from rear to front, and exhausting the air through an annular slot located between the propeller and the engine with the aid of a blower mounted on the spinner. The test apparatus consisted essentially of a stub wing having a 5-foot chord and a 15-foot span, an engine nacelle of 20 inches diameter enclosing a 25-horsepower electric motor, and three blowers mounted on propeller spinners. Two of the blowers utilize centrifugal force while the other uses the lift from airfoils to force the air out radially through the exit slot. Maximum efficiencies of over 70 percent were obtained for the system as a whole. Pressures were measured over the entire flight range which were in excess of those necessary to cool present-day engines, The results indicated that blowers mounted on propeller spinners could be built sufficiently powerful and efficient to warrant their use as the only, or chief, means of forcing air through the cooling system, so that cooling would be independent of the speed of the airplane.

Biermann, David↗
NASA NTRS1972

Optimum performance of static propellers and rotors.

A criterion for the optimum performance of static propellers and hovering helicopter rotors is developed. Numerical results are presented for the optimum radial distributions of circulation and inflow at the propeller disk and relating the optimum power coefficient and the figure of merit to the thrust coefficient. It is shown that the present theory, which fully accounts for the effect of slipstream rotation, predicts optimum distributions of circulation and inflow that differ significantly from those based on approximate methods.

Wu, J. C.↗
NASA NTRS2000

Test Report for NASA MSFC Support of the Linear Aerospike SR-71 Experiment (LASRE)

The Linear Aerospike SR-71 Experiment (LASRE) was performed in support of the Reusable Launch Vehicle (RLV) program to help develop a linear aerospike engine. The objective of this program was to operate a small aerospike engine at various speeds and altitudes to determine how slipstreams affect the engine's performance. The joint program between government and industry included NASA!s Dryden Flight Research Center, The Air Force's Phillips Laboratory, NASA's Marshall Space Flight Center, Lockheed Martin Skunkworks, Lockheed-Martin Astronautics, and Rocketdyne Division of Boeing North American. Ground testing of the LASRE engine produced two successful hot-fire tests, along with numerous cold flows to verify sequencing and operation before mounting the assembly on the SR-71. Once installed on the aircraft, flight testing performed several cold flows on the engine system at altitudes ranging from 30,000 to 50,000 feet and Mach numbers ranging from 0.9 to 1.5. The program was terminated before conducting hot-fires in flight because excessive leaks in the propellant supply systems could not be fixed to meet required safety levels without significant program cost and schedule impacts.

Elam, S. K.↗